Experiment: Combined effects of CO2, temperature, irradiance and time on the physiological performance of Chondrus crispus (Rhodophyta)

In natural environments, marine biotas are exposed to a variety of simultaneously acting abiotic factors. Among these, temperature, irradiance and CO2 availability are major factors influencing the physiological performance of marine macroalgae. To test whether elevated levels of CO2 may remediate the otherwise reduced performance of uncalcified seaweeds under the influence of other stressful abiotic factors, we performed multifactorial experiments with the red alga Chondrus crispus from Helgoland (North Sea) with two levels of CO2, temperature and irradiance: low and high pCO2 levels were tested in combination with either (1) optimal and low irradiances or (2) optimal and sub-lethal high temperatures for growth. Performance of C. crispus was evaluated as biomass increase and relative growth rates (RGR), gross photosynthesis and pigment content. Acclimations of growth and photosynthesis were measured after 4 and 8 days. Acclimation time was crucial for elucidating single or combined CO2 effects on growth and photosynthesis. Signifi- cant CO2 effects became evident only in combination with either elevated temperature or reduced irradiance. Growth and photosynthesis had divergent patterns: RGR and biomass significantly increased only under a combination of high pCO2 and elevated temperature; gross photosynthesis was significantly reduced under high pCO2 conditions at low irradiance. Pigment content varied in response to irradiance and temperature, but was independent of pCO2.

Comparative responses of two dominant Antarctic phytoplankton taxa to interactions between ocean acidification, warming, irradiance, and iron availability

We investigated the responses of the ecologically dominant Antarctic phytoplankton species Phaeocystis antarctica (a prymnesiophyte) and Fragilariopsis cylindrus (a diatom) to a clustered matrix of three global change variables (CO2, mixed-layer depth, and temperature) under both iron (Fe)-replete and Fe-limited conditions based roughly on the Intergovernmental Panel on Climate Change (IPCC) A2 scenario: (1) Current conditions, 39 Pa (380 ppmv) CO2, 50 µmol photons/m**2/s light, and 2°C; (2) Year 2060, 61 Pa (600 ppmv) CO2, 100 µmol photons/m**2/s light, and 4°C; (3) Year 2100, 81 Pa (800 ppmv) CO2, 150 µmol photons/m**2/s light, and 6°C. The combined interactive effects of these global change variables and changing Fe availability on growth, primary production, and cell morphology are species specific. A competition experiment suggested that future conditions could lead to a shift away from P. antarctica and toward diatoms such as F. cylindrus. Along with decreases in diatom cell size and shifts from prymnesiophyte colonies to single cells under the future scenario, this could potentially lead to decreased carbon export to the deep ocean. Fe : C uptake ratios of both species increased under future conditions, suggesting phytoplankton of the Southern Ocean will increase their Fe requirements relative to carbon fixation. The interactive effects of Fe, light, CO2, and temperature on Antarctic phytoplankton need to be considered when predicting the future responses of biology and biogeochemistry in this region.

Combined effects of short-term ocean acidification and heat shock in a benthic copepod Tigriopus japonicus Mori

Warming of the world's oceans is predicted to have many negative effects on organisms as they have optimal thermal windows. In coastal waters, however, both temperatures and pCO2 (pH) exhibit diel variations, and biological performances are likely to be modulated by physical and chemical environmental changes. To understand how coastal zooplankton respond to the combined impacts of heat shock and increased pCO2, the benthic copepod Tigriopus japonicus were treated at temperatures of 24, 28, 32 and 36 °C to simulate natural coastal temperatures experienced in warming events, when acclimated in the short term to either ambient (LC, 390 µatm) or future CO2 (HC, 1000 µatm). HC and heat shock did not induce any mortality of T. japonicus, though respiration increased up to 32 °C before being depressed at 36 °C. Feeding rate peaked at 28 °C but did not differ between CO2 treatments. Expression of heat shock proteins (hsps mRNA) was positively related to temperature, with no significant differences between the CO2 concentrations. Nauplii production was not affected across all treatments. Our results demonstrate that T. japonicus responds more sensitively to heat shocks rather than to seawater acidification; however, ocean acidification may synergistically act with ocean warming to mediate the energy allocation of copepods.

Preconditioning in the reef-building coral Pocillopora damicornis and the potential for trans-generational acclimatization in coral larvae under future climate change conditions

Coral reefs are globally threatened by climate change-related ocean warming and ocean acidification (OA). To date, slow-response mechanisms such as genetic adaptation have been considered the major determinant of coral reef persistence, with little consideration of rapid-response acclimatization mechanisms. These rapid mechanisms such as parental effects that can contribute to trans-generational acclimatization (e.g. epigenetics) have, however, been identified as important contributors to offspring response in other systems. We present the first evidence of parental effects in a cross-generational exposure to temperature and OA in reef-building corals. Here, we exposed adults to high (28.9°C, 805 µatm PCO2) or ambient (26.5°C, 417 µatm PCO2) temperature and OA treatments during the larval brooding period. Exposure to high treatment negatively affected adult performance, but their larvae exhibited size differences and metabolic acclimation when subsequently re-exposed, unlike larvae from parents exposed to ambient conditions. Understanding the innate capacity corals possess to respond to current and future climatic conditions is essential to reef protection and maintenance. Our results identify that parental effects may have an important role through (1) ameliorating the effects of stress through preconditioning and adaptive plasticity, and/or (2) amplifying the negative parental response through latent effects on future life stages. Whether the consequences of parental effects and the potential for trans-generational acclimatization are beneficial or maladaptive, our work identifies a critical need to expand currently proposed climate change outcomes for corals to further assess rapid response mechanisms that include non-genetic inheritance through parental contributions and classical epigenetic mechanisms.

CO2 and vitamin B12 interactions determine bioactive trace metal requirements of a subarctic Pacific diatom

Phytoplankton growth can be limited by numerous inorganic nutrients and organic growth factors. Using the subarctic diatom Attheya sp. in culture studies, we examined how the availability of vitamin B(12) and carbon dioxide partial pressure (pCO(2)) influences growth rate, primary productivity, cellular iron (Fe), cobalt (Co), zinc (Zn) and cadmium (Cd) quotas, and the net use efficiencies (NUEs) of these bioactive trace metals (mol C fixed per mol cellular trace metal per day). Under B(12)-replete conditions, cells grown at high pCO(2) had lower Fe, Zn and Cd quotas, and used those trace metals more efficiently in comparison with cells grown at low pCO(2). At high pCO(2), B(12)-limited cells had ~50% lower specific growth and carbon fixation rates, and used Fe ~15-fold less efficiently, and Zn and Cd ~3-fold less efficiently, in comparison with B(12)-replete cells. The observed higher Fe, Zn and Cd NUE under high pCO(2)/B(12)-replete conditions are consistent with predicted downregulation of carbon-concentrating mechanisms. Co quotas of B(12)-replete cells were 5- to 14-fold higher in comparison with B(12)-limited cells, suggesting that >80% of cellular Co of B(12)-limited cells was likely from B(12). Our results demonstrate that CO(2) and vitamin B(12) interactively influence growth, carbon fixation, trace metal requirements and trace metal NUE of this diatom. This suggests the need to consider complex feedback interactions between multiple environmental factors for this biogeochemically critical group of phytoplankton in the last glacial maximum as well as the current and future changing ocean.

Short- and long-term conditioning of a temperate marine diatom community to acidification and warming

Ocean acidification and greenhouse warming will interactively influence competitive success of key phytoplankton groups such as diatoms, but how long-term responses to global change will affect community structure is unknown. We incubated a mixed natural diatom community from coastal New Zealand waters in a short-term (two-week) incubation experiment using a factorial matrix of warming and/or elevated pCO2 and measured effects on community structure. We then isolated the dominant diatoms in clonal cultures and conditioned them for 1 year under the same temperature and pCO2 conditions from which they were isolated, in order to allow for extended selection or acclimation by these abiotic environmental change factors in the absence of interspecific interactions. These conditioned isolates were then recombined into 'artificial' communities modelled after the original natural assemblage and allowed to compete under conditions identical to those in the short-term natural community experiment. In general, the resulting structure of both the unconditioned natural community and conditioned 'artificial' community experiments was similar, despite differences such as the loss of two species in the latter. pCO2 and temperature had both individual and interactive effects on community structure, but temperature was more influential, as warming significantly reduced species richness. In this case, our short-term manipulative experiment with a mixed natural assemblage spanning weeks served as a reasonable proxy to predict the effects of global change forcing on diatom community structure after the component species were conditioned in isolation over an extended timescale. Future studies will be required to assess whether or not this is also the case for other types of algal communities from other marine regimes.

In Situ effects of low pH and elevated HCO3 on juvenile massive Porites spp. in Moorea, French Polynesia

Juvenile colonies of massive Porites spp. were exposed to manipulated pH and bicarbonate ([HCO3-]) in situ to test the hypothesis that ocean acidification (OA) does not affect respiration and calcification. Incubations lasted 28 h and exposed corals to ambient temperature and light with ecologically relevant water motion. Three treatments were applied: (1) ambient conditions of pH 8.04 and 1751 µmol HCO3- kg(-1) (Treatment 1), (2) pCO2-induced ocean acidification of pH 7.73 and 2011 µmol HCO3- kg(-1) (Treatment 2), and (3) pCO2 and HCO3--enriched seawater of pH 7.69 and 2730 µmol HCO3- kg(-1) (Treatment 3). The third treatment providing elevated [HCO3-] was used to test for stimulatory effects of dissolved inorganic carbon on calcification under low pH and low saturation of aragonite (Omega arag), but it does not reflect conditions expected to occur under CO2-driven OA. Calcification of juvenile massive Porites spp. was affected by treatments, with an 81% elevation in Treatment 3 versus Treatment 1, but no difference between Treatments 1 and 2; respiration and the metabolic expenditure concurrent with calcification remained unaffected. These findings indicate that juvenile massive Porites spp. are resistant to short exposures to OA in situ, and separately, that they can increase calcification at low pH and low Omega arag if [HCO3-] is elevated. Juvenile Porites spp. may therefore be limited by dissolved inorganic carbon under ambient pCO2 conditions

Coastal Urban Flood Resislience versus Climate Change

Processes of founding and expanding cities in coastal areas have undergone great changes over time driven by environmental conditions. Coastal settlements looked for places above flood levels and away from swamps and other wetlands whenever possible. As populations grew, cities were extending trying to avoid low and wet lands. No city has been able to limit its growth. The risk of flooding can never be eliminated, but only reduced to the extent possible. Flooding of coastal areas is today dramatically attributed to eustasic sea level rise caused by global climate change. This can be inaccurate. Current climate change is generating an average sea level upward trend, but other regional and local factors result in this trend being accentuated in some places or attenuated, and even reversed, in others. Then, the intensity and frequency of coastal flooding around the planet, although not so much as a unique result of this general eustasic elevation, but rather of the superposition of marine and crustal dynamic elements, the former also climate-related, which give rise to a temporary raising in average sea level in the short term. Since the Little Ice Age the planet has been suffering a global warming change leading to sea level rise. The idea of being too obeying to anthropogenic factors may be attributed to Arrhenius (1896), though it is of much later highlight after the sixties of the last century. Never before, the human factor had been able of such an influence on climate. However, other types of changes in sea levels became apparent, resulting from vertical movements of the crust, modifications of sea basins due to continents fracturing, drifting and coming together, or to different types of climate patterns. Coastal zones are then doubly susceptible to floods. Precipitation immediately triggers pluvial flooding. If it continues upland or when snow and glaciers melt eventually fluvial flooding can occur. The urban development presence represents modifying factors. Additional interference is caused by river and waste water drainage systems. Climate also influences sea levels in coastal areas, where tides as well as the structure and dynamic of the geoid and its crust come into play. From the sea, waters can flood and break or push back berms and other coastline borders. The sea level, controlling the mouth of the main channel of the basin's drainage system, is ultimately what governs flood levels. A temporary rise in sea level acts as a dam at the mouth. Even in absence of that global change, so, floods are likely going to increase in many urban coastal areas. Some kind of innovative methodologies and practices should be needed to get more flood resilience cities

Crack width control in RC elements with recycled steel fibres and applications to integral structures : theoretical and experimental study

El presente trabajo trata de elementos reforzados con barras de armadura y Fibras Metálicas Recicladas (FMR). El objetivo principal es mejorar el comportamiento a fisuración de elementos sometidos a flexión pura y a flexión compuesta, aumentando en consecuencia las prestaciones en servicio de aquellas estructuras con requerimientos estrictos con respecto al control de fisuración. Entre éstas últimas se encuentran las estructuras integrales, es decir aquellas estructuras sin juntas (puentes o edificios), sometidas a cargas gravitatorias y deformaciones impuestas en los elementos horizontales debidas a retracción, fluencia y temperatura. Las FMR son obtenidas a partir de los neumáticos fuera de uso, y puesto que el procedimiento de reciclado se centra en el caucho en vez que en el acero, su forma es aleatoria y con longitud variable. A pesar de que la eficacia del fibrorefuerzo mediante FMR ha sido demostrada en investigaciones anteriores, la innovación que representa este trabajo consiste en proponer la acción combinada de barras convencionales y FMR en la mejora del comportamiento a fisuración. El objetivo es por tanto mejorar la sostenibilidad del proyecto de la estructura en HA al utilizar materiales reciclados por un lado, y aumentando por el otro la durabilidad. En primer lugar, se presenta el estado del arte con respecto a la fisuración en elementos de HA, que sucesivamente se amplía a elementos reforzados con barras y fibras. Asimismo, se resume el método simplificado para el análisis de columnas de estructuras sin juntas ya propuesto por Pérez et al., con particular énfasis en aquellos aspectos que son incompatibles con la acción de las fibras a nivel seccional. A continuación, se presenta un modelo para describir la deformabilidad seccional y la fisuración en elementos en HA, que luego se amplía a aquellos elementos reforzados con barras y fibras, teniendo en cuenta también los efectos debidos a la retracción (tension stiffening negativo). El modelo es luego empleado para ampliar el método simplificado para el análisis de columnas. La aportación consiste por tanto en contar con una metodología amplia de análisis para este tipo de elementos. Seguidamente, se presenta la campaña experimental preliminar que ha involucrado vigas a escala reducida sometidas a flexión simple, con el objetivo de validar la eficiencia y la usabilidad en el hormigón de las FMR de dos diferentes tipos, y su comportamiento con respecto a fibras de acero comerciales. Se describe a continuación la campaña principal, consistente en ensayos sobre ocho vigas en flexión simple a escala 1:1 (variando contenido en FRM, Ø/s,eff y recubrimiento) y doce columnas a flexión compuesta (variando contenido en FMR, Ø/s,eff y nivel de fuerza axil). Los resultados obtenidos en la campaña principal son presentados y comentados, resaltando las mejoras obtenidas en el comportamiento a fisuración de las vigas y columnas, y la rigidez estructural de las columnas. Estos resultados se comparan con las predicciones del modelo propuesto. Los principales parámetros estudiados para describir la fisuración y el comportamiento seccional de las vigas son: la separación entre fisuras, el alargamiento medio de las armaduras y la abertura de fisura, mientras que en los ensayos de las columnas se ha contrastado las leyes momento/curvatura, la tensión en las barras de armadura y la abertura de fisura en el empotramiento en la base. La comparación muestra un buen acuerdo entre las predicciones y los resultados experimentales. Asimismo, se nota la mejora en el comportamiento a fisuración debido a la incorporación de FMR en aquellos elementos con cuantías de armadura bajas en flexión simple, en elementos con axiles bajos y para el control de la fisuración en elementos con grandes recubrimientos, siendo por tanto resultados de inmediato impacto en la práctica ingenieril (diseño de losas, tanques, estructuras integrales, etc.). VIIIComo punto final, se presentan aplicaciones de las FMR en estructuras reales. Se discuten dos casos de elementos sometidos a flexión pura, en particular una viga simplemente apoyada y un tanque para el tratamiento de agua. En ambos casos la adicción de FMR al hormigón lleva a mejoras en el comportamiento a fisuración. Luego, utilizando el método simplificado para el análisis en servicio de columnas de estructuras sin juntas, se calcula la máxima longitud admisible en casos típicos de puentes y edificación. En particular, se demuestra que las limitaciones de la práctica ingenieril actual (sobre todo en edificación) pueden ser aumentadas considerando el comportamiento real de las columnas en HA. Finalmente, los mismos casos son modificados para considerar el uso de MFR, y se presentan las mejoras tanto en la máxima longitud admisible como en la abertura de fisura para una longitud y deformación impuesta. This work deals with elements reinforced with both rebars and Recycled Steel Fibres (RSFs). Its main objective is to improve cracking behaviour of elements subjected to pure bending and bending and axial force, resulting in better serviceability conditions for these structures demanding keen crack width control. Among these structures a particularly interesting type are the so-called integral structures, i.e. long jointless structures (bridges and buildings) subjected to gravitational loads and imposed deformations due to shrinkage, creep and temperature. RSFs are obtained from End of Life Tyres, and due to the recycling process that is focused on the rubber rather than on the steel they come out crooked and with variable length. Although the effectiveness of RSFs had already been proven by previous research, the innovation of this work consists in the proposing the combined action of conventional rebars and RSFs to improve cracking behaviour. Therefore, the objective is to improve the sustainability of RC structures by, on the one hand, using recycled materials, and on the other improving their durability. A state of the art on cracking in RC elements is firstly drawn. It is then expanded to elements reinforced with both rebars and fibres (R/FRC elements). Finally, the simplified method for analysis of columns of long jointless structures already proposed by Pérez et al. is resumed, with a special focus on the points that conflict when taking into account the action of fibres. Afterwards, a model to describe sectional deformability and cracking of R/FRC elements is presented, taking also into account the effect of shrinkage (negative tension stiffening). The model is then used to implement the simplified method for columns. The novelty represented by this is that a comprehensive methodology to analyse this type of elements is presented. A preliminary experimental campaign consisting in small beams subjected to pure bending is described, with the objective of validating the effectiveness and usability in concrete of RSFs of two different types, and their behaviour when compared with commercial steel fibres. With the results and lessons learnt from this campaign in mind, the main experimental campaign is then described, consisting in cracking tests of eight unscaled beams in pure bending (varying RSF content, Ø/s,eff and concrete cover) and twelve columns subjected to imposed displacement and axial force (varying RSF content, Ø/s,eff and squashing load ratio). The results obtained from the main campaign are presented and discussed, with particular focus on the improvement in cracking behaviour for the beams and columns, and structural stiffness for the columns. They are then compared with the proposed model. The main parameters studied to describe cracking and sectional behaviours of the beam tests are crack spacing, mean steel strain and crack width, while for the column tests these were moment/curvature, stress in rebars and crack with at column embedment. The comparison showed satisfactory agreement between experimental results and model predictions. Moreover, it is pointed out the improvement in cracking behaviour due to the addition of RSF for elements with low reinforcement ratios, elements with low squashing load ratios and for crack width control of elements with large concrete covers, thus representing results with a immediate impact in engineering practice (slab design, tanks, integral structures, etc.). Applications of RSF to actual structures are finally presented. Two cases of elements in pure bending are presented, namely a simple supported beam and a water treatment tank. In both cases the addition of RSF to concrete leads to improvements in cracking behaviour. Then, using the simplified model for the serviceability analysis of columns of jointless structures, the maximum achievable jointless length of typical cases of a bridge and building is obtained. In XIIparticular, it is shown how the limitations of current engineering practice (this is especially the case of buildings) can be increased by considering the actual behaviour of RC supports. Then, the same cases are modified considering the use of RSF, and the improvements both in maximum achievable length and in crack width for a given length and imposed strain at the deck/first floor are shown.

Análisis de la degradación, desintegración y biodegradabilidad de bolsas de poliéster y almidón en compostaje de residuos urbanos: escalas de laboratorio e industrial

El principal objetivo de esta tesis es verificar que las bolsas biodegradables de copoliéster (PBAT) con base de almidón (UNE 13432: 2001) alcanzan los niveles de degradación y desintegración requeridos para su certificación (%D= ≥ 90%), medido en condiciones reales de compostaje industrial. Para lograr mayor representatividad, los ensayos se han realizado en dos plantas de tratamiento de residuos urbanos en las que se aplican las técnicas de compostaje más comunes en el ámbito europeo y nacional, pila y túnel, mediante el compostaje de la FORSU. Se llevaron a cabo dos tipos de ensayos. Por un lado se realizó un ensayo escala de laboratorio (ISO 14855), orientado como indicador de la biodegradabilidad del polímero en el formato bolsa comercializado. Por otro lado, se desarrollaron una batería de ensayos realizados en dos plantas de compostaje de residuos urbanos: el Centro de Tratamiento de Residuos de Torija (Ávila), que realiza el compostaje mediante pila volteada, y el Centro de Tratamiento de Residuos de Arenas de San Pedro (Ávila), que realiza el compostaje en túnel. Para la obtención de resultados se han contrastado parámetros como el porcentaje de biodegradación (%B), el porcentaje de desintegración (%D), degradación superficial de las muestras, calidad de la FORSU inicial (caracterizaciones y análisis físico-químico) y calidad del MB final (análisis físico-químico e IG). Atendiendo al objetivo general se demuestra que las bolsas de copoliéster con base de almidón certificadas (UNE EN 13432:2001) han alcanzado el 94,37% ± 0,007% de desintegración en la planta de compostaje de FORSU con pila volteada; y el 86,36% ± 0,151% en la planta de compostaje de FORSU con túnel estático. A pesar de la aparente diferencia, el resultado del análisis concluye que no existen diferencias estadísticamente significativas entre técnicas de compostaje. La presencia de impropios y el contendido de metales pesados en la FORSU no han influido en la desintegración de las bolsas de estudio. En cambio, se ha detectado una influencia estadísticamente significativa entre el contenido de materia orgánica total y de nutrientes de la FORSU y el porcentaje de desintegración de las muestras. No se detectado una relación estadísticamente significativa entre la presencia de bolsas de estudio en las concentraciones definidas, y la calidad del MB, medido mediante el análisis físico-químico, microbiológico y el IG del MB. La concentración de los metales pesados en la mayoría de las muestras de material bioestabilizado cumplió con los límites establecidos para la categoría A, aplicable al “compost” procedente de la fracción orgánica recogida de forma separada según el RD 506/2013 de productos fertilizantes. También se detectó fitotoxicidad alta (FA) según la metodología y criterios de valoración definidos. Esta fitotoxicidad no está relacionada con la presencia de las bolsas de estudio sino con la calidad de la FORSU de partida y/o con los productos liberados durante el proceso de compostaje. ABSTRACT The main objective of this thesis is to verify that the copolyester (PBAT) starch based (UNE 13432: 2001) biodegradable bags reach levels of degradation and disintegration required for it´s certification (% D = ≥ 90%), measured in terms of real industrial composting. The tests were performed at two municipal solid waste (MSW) treatment plants, where the most common composting techniques applied at European and national level were represented, windrow and tunnel. Two types of tests were carried out: First, a laboratory scale test (ISO 14855), as an indicator of the polymer biodegradation of the commercialized bag format. Second, a battery of tests was conducted at two MSW composting plants, Waste Treatment Center of Torija (Guadalajara), that makes compost by turned pile, and the Waste Treatment Center of Arenas de San Pedro (Ávila), where makes compost by static tunnel. To obtain the results, the parameters such as the biodegradation percentage (% B), the disintegration percentage (% D), surface degradation of the samples, the initial quality of FORSU (characterizations and physico-chemical analysis) and bioestabilithated material (MB) quality (physico-chemical analysis and IG) have been compared. In reference to the general aim It shows that the copolyester starch based certified (UNE-EN 13432) bags have reached 94.37% ± 0.007% of disintegration in the composting turned pile; and 86.36% ± 0.151% in the static tunnel. Despite the apparent difference, the result of the analysis concludes that there are no statistically significant differences between composting techniques. The presence of non-compostable materials and the heavy metals content in the FORSU has not affected in the disintegration of the bags. Instead, It has been detected a statistically significant influence over the total organic matter content and nutrient content in the FORSU and the samples disintegration percentage. A statistically significant relationship between the bag presence in the defined concentrations and the quality of MB measured by physical-chemical analysis, microbiological analysis and IG of the MB is not detected. The concentration of heavy metals in most MB samples was within the limits of A-Class, applicable to "compost" from organic waste collected separately according to RD 506/2013 of fertilizers. High phytotoxicity (FA) was also detected according to the methodology and evaluation defined. The phytotoxicity is not related to the presence of bags but it is with the FORSU initial quality and/or with the products released during the composting process.

Investigación sobre tratamientos de aguas seguros en emergencias

Esta Tesis Doctoral tiene como principal objetivo el obtener una cadena de tratamientos seguros de aguas seriados que nos permita asegurar la calidad de las aguas para consumo humano en caso de emergencias, de tal forma que se minimicen los efectos de acciones hostiles, como sabotajes o actos terroristas, desastres naturales, etc y buscar soluciones adecuadas para garantizar en este caso la salud. Las plantas de tratamientos de aguas existentes comercialmente no aseguran dicha calidad y la documentación sobre el tema presenta vacíos de conocimiento, contradicciones entre resultados de investigaciones o insostenibilidad de conclusiones de las mismas. Estas carencias nos permiten determinar los aspectos a tratar durante la investigación. Por ello, este objetivo se concretó en tres acciones: Investigar sobre rendimientos de plantas convencionales en eliminación de microorganismos y productos tóxicos y peligrosos. Introducir mejoras que garanticen el rendimiento de las plantas convencionales. Investigar sobre la conveniencia de complementar las instalaciones existentes buscando seguridad y garantía sanitaria. Y se desarrollaron tres líneas de investigación: LI 1 “Inorgánicos”: Investigación sobre la eliminación de los metales boro, cobre y molibdeno mediante procesos de intercambio iónico y de coagulaciónfloculación- decantación. LI 2 “Compuestos Orgánicos Volátiles”: Investigación sobre la eliminación de los compuestos orgánicos 1,1 dicloroetano, 1,2 dicloroetano, clorobenceno, 1,3 dicloropropeno y hexacloro 1,3 butadieno mediante procesos de carbón activo granular y de oxidación avanzada. LI 3 “Plantas portátiles”: Investigación sobre plantas existentes portátiles para verificar su rendimiento teórico y proponer mejoras. Estas líneas de investigación se desarrollaron tanto en el nivel teórico como en el empírico, bien sea en laboratorio como en campo. A lo largo del documento se demuestra que las principales fuentes de contaminación, salvo la degradación de yacimientos naturales, proceden de la actividad humana (efluentes industriales y agrícolas, aguas residuales y actividades beligerantes) que provocan un amplio espectro de enfermedades por lo que dificultan tanto la definición de la fuente como la anticipada detección de la enfermedad. Las principales conclusiones que se obtuvieron están relacionadas con el rendimiento de eliminación de los parámetros tras la aplicación de los procesos y plantas de tratamiento de aguas anteriormente reseñadas. Sin embargo, el verdadero elemento designador de originalidad de esta Tesis Doctoral, tal como se ha reseñado arriba, radica en la definición de un sistema seriado de procesos de tratamiento de aguas que asegura la calidad en caso de emergencia. Éste se define en el siguiente orden: pretratamiento, oxidación, coagulación-floculación-decantación, filtración por arena, intercambio iónico, carbón activo granular, microfiltración, radiación UV, ósmosis inversa, radiación UV y cloración final. The main objective of this Thesis is to obtain a chain of stepwise safe water treatments that allow us to ensure the quality of water for human consumption in case of emergencies, so that the effects of hostile actions, such as sabotage or terrorism, natural disasters, etc. and seek appropriate solutions in this case to ensure health. The existing commercial water treatment plants do not ensure quality, and the documentation on the subject presents knowledge gaps or contradictions. These gaps allow us to determine the issues to be discussed during the investigation. Therefore, this objective was manifested in three actions: Researching yields in commercial plants and microorganisms, or toxic and dangerous products removal. Improvements to ensure the performance of conventional plants. Inquire about the advisability of implementing existing facilities for safety and health guarantee. And three lines of research are developed: LI 1 “Inorganic elements”: Research removing metals iron, copper and molybdenum by ion exchange processes and coagulation-flocculation-decantation. LI 2 “Volatile Organic Compounds”: Research removing organic compounds 1,1 dichloroethane, 1,2 dichloroethane, chlorobenzene, 1,3-dichloropropene and 1,3-butadiene hexachloro through processes of granular activated carbon and advanced oxidation. LI 3 “Compact Water Treatment Plants”: Research on existing packaged plants to verify theoretical performance and suggest improvements. These lines of research are developed both theoretically and empirically, both in the laboratory and in the field. Throughout the document, it is evident that the main sources of pollution, other than the degradation of natural deposits, come from human activity (industrial and agricultural effluents, sewage and belligerent activities) which cause a broad spectrum of diseases which hamper both the definition of the source and the early detection of the disease. The main conclusions drawn are related to both the removal efficiency parameters after application of processes and treatment plants outlined above water. However, the real designator of originality of this thesis, such as outlined above, lies in the definition of a serial system water treatment processes assuring quality in case of emergency. This is defined in the following order: pretreatment, oxidation, coagulation-flocculation-sedimentation, sand filtration, ion exchange, granular activated carbon, microfiltration, UV radiation, reverse osmosis, UV radiation and final chlorination.

Respuestas anatómico fisiológicas frente a estrés hídrico en plantaciones de especies de crecimiento rápido para la producción de biomasa

El objetivo general de la presente Tesis es identificar algunas de las características anatómico-fisiológicas que confieren la capacidad de alcanzar una mejor productividad bajo clima mediterráneo a plantas de diversos genotipos de los géneros Populus y Eucalyptus, caracterizados por su carácter pionero, elevado crecimiento y vulnerabilidad a la cavitación. En los dos primeros capítulos se hace un seguimiento de la conductancia estomática a una selección de clones de eucalipto cultivados en invernadero, sometidos a diferentes dotaciones hídricas. Se realizaron además mediciones periódicas del pH de la savia del tallo y de la pérdida de conductividad hidráulica para investigar su implicación en la regulación química e hidraúlica del cierre estomático. Las variaciones en el pH de la savia obtenidas parecen responder a cambios en el déficit de presión de vapor de agua atmosférico y no a diferencias en la disponibilidad de agua en el suelo. La conductancia estomática presentó una correlación positiva significativa con el pH de la savia, pero no con la conductividad hidráulica. La variabilidad de la conductividad hidráulica máxima se discute a la luz de recientes investigaciones sobre los materiales constituyentes de las membranas de las punteaduras. Los clones que mostraron mayores conductancias hidráulicas y estomáticas presentaron valores más altos de producción y supervivencia, poniendo de manifiesto la utilidad del estudio de estas variables. Por el contrario, los valores más bajos de conductancia estomática e hidraúlica se encontraron en clones que han resultado un fracaso en plantaciones comerciales, en particular, fue destacable el mal resultado de un clon procedente de autocruzamiento respecto de otros híbridos. En el tercer capítulo de la tesis se estudian características anatómicas y funcionales del xilema relacionadas con la eficiencia en el transporte de agua a las hojas, y que pueden afectar directa o indirectamente a la transpiración y al crecimiento. Los estudios anatómicos fueron realizados sobre brotes anuales de chopo en una plantación situada en Granada, en condiciones de riego limitante. La combinación de rasgos anatómicos más favorable de cara a la producción de biomasa fue una densidad alta de vasos de diámetro intermedio. Los clones más productivos figuraron entre los más resistentes a la cavitación. Para estudiar el crecimiento de masas arboladas se utilizan frecuentemente parámetros fisiológicos como el índice de area foliar (LAI). La estimación del LAI a partir de fotografías hemisféricas aplicada a tallares de chopo plantados a alta densidad y a turno corto para biomasa se lleva a cabo mediante una metodología reciente empleada y discutida en el cuarto capítulo de la Tesis. Los resultados muestran que las diferencias de producción existentes entre genotipos, localidades de medición con diferentes dosis de riego, y años, pueden predecirse a partir de la determinación del índice de área foliar tanto por métodos directos como indirectos de estimación. Tanto los estudios realizados en eucalipto como en chopo han mostrado que los genotipos con menores producciones de biomasa en campo alcanzaron los menores valores de conductancia estomática en las condiciones más favorables así como el menor número de vasos en el xilema. La estrecha relación entre crecimiento y LAI confirma una vez más la importancia del desarrollo de la copa para sostener un buen crecimiento. El mayor desarrollo de la copa y rendimiento en biomasa se midieron en uno de los clones con un número de vasos más elevado, y menor vulnerabilidad a la cavitación en condiciones de estrés. Estos resultados ponen de manifiesto la importancia de las características anatómicas y funcionales del xilema como condicionantes del patrón de crecimiento de las plantas y el comportamiento de los estomas. ABSTRACT A number of anatomical xylem traits and physiological variables were analyzed in genotypes of both the Populus and Eucalyptus genera with the main aim of identifying traits in the genotypes which confer the ability to produce an acceptable biomass yield under Mediterranean climatic conditions. In the first two chapters of this PhD, the results of two experiments carried out on several clones of the species Eucalyptus globulus Labill. are presented. Chapters three and four include the results of another two trials on four poplar hybrid genotypes. One of the initial plant responses to water stress is stomatal closure, which can be triggered by hydraulic and/or chemical signals. The two first chapters of this PhD deal with trials in which stomatal conductance and percentage loss of hydraulic conductivity were monitored on a set of eucalyptus clones supplied by ENCE (former National Cellulose Company) and currently used in the company’s own commercial plantings. The experimental trials were carried out in greenhouses and the plants were submitted to two different watering regimes. The pH of the stem sap was periodically measured as the greenhouse temperature and humidity changed. The aim of these measurements was to investigate the role of both sap pH and percentage loss of hydraulic conductivity on stomatal regulation. The results obtained suggest that changes in sap pH are a response to vapor pressure deficit changes rather than to differences in soil water availability. We found significant correlation between stomatal conductance and sap pH, although no significant relationship was found between stomatal conductance and hydraulic conductivity. Variability in maximum hydraulic conductivity is discussed based on recent pit membrane constituent research. The study of hydraulic conductivity proved helpful in order to detect the clones with both higher growth and greater chance of survival, since clones displaying the lowest hydraulic conductivities were those that failed in commercial plantings. Anatomical xylem traits define the water transport efficiency to leaves and can therefore limit transpiration and growth. The third chapter of this PhD addresses anatomical xylem traits in poplar. One year old stem samples were taken from a water-stressed trial in Granada. The anatomical xylem study proved useful for detecting the lowest yielding genotypes. Clones with intermediate vessel size and high vessel densities were found to be those with the highest biomass yield. Differences in cavitation resistance depending on the clone tested and the water treatment applied were also found. The clones with the highest biomass yield were found to be among the most cavitation resistant clones in each watering regime. Xylem and physiological traits along with stomatal behavior are useful tools to determine plant growth. In order to study plantings or forests, it is more common to employ other physiological variables such as leaf area index (LAI). LAI estimation from hemispherical photographs applied to short rotation woody crops is a recently developed method that still requires fine tuning through further investigation. In the fourth chapter, data from LAI monitoring over two consecutive years were analyzed in two different locations where different irrigation treatments were applied. The results showed that differences in yield between genotypes, different irrigation regimes and years could be predicted by using the LAI estimates, either through direct or indirect estimation methods. Our studies of poplar and eucalyptus have shown that the field-grown genotypes with the lowest biomass yield displayed the lowest values of stomatal conductance under the most favorable environmental conditions and also had a low number of xylem conduits. The close relationship between LAI and growth highlights the importance of crown development in biomass growth. The highest LAI and biomass yield were recorded in one of the clones with higher vessel density and the lowest vulnerability to cavitation under stress conditions. These results underline the importance of research into anatomical and functional traits as factors influencing plant growth patterns and stomatal behavior.

Remoção de atividade estrogênica do hormônio 17β-Estradiol em processos de oxidação de águas para abastecimento

Muitos oxidantes químicos reativos acarretam na ruptura de estruturas moleculares complexas de vários tipos de compostos orgânicos decompondo-as em estruturas mais simples e propiciando condições melhores para uma efetiva ação de micro-organismos na degradação biológica. A presença de hormônios, entre eles o 17β-estradiol, em estações de tratamento de esgoto e em águas subterrâneas e superficiais mostra a necessidade de uma avaliação dos processos de tratamento convencionais. O objetivo deste trabalho foi a análise e remoção de hormônios através de técnicas de cloração e ozonização de amostras reais de águas de saída de filtro de estações de tratamento de água (ETAs), operadas pelo Serviço Autônomo de Água e Esgoto (SAAE) de São Carlos (ETA Centro), que capta águas dos ribeirão Feijão e córrego Espraiado e pela Sociedade de Abastecimento de Água e Saneamento S/A (SANASA) de Campinas (ETAs 3 e 4), que capta águas do rio Atibaia. Foram realizados ensaios contaminando-se as amostras com 17β-estradiol, que é o hormônio natural mais presente no meio ambiente, em concentração de 6.000 ng L-1, submetendo-se tratamento com dosagens em torno de 0,5 e 2,0 mg L-1 desses oxidantes, em tempos de contato de, respectivamente, 10 e 30 min. As amostras submetidas à contaminação e tratamento e as de controle (sem contaminação e tratamento) foram analisadas através da remoção do 17β-estradiol com a verificação da atividade estrogênica das amostras por ensaios de Sistema de Expressão de Estrogênio Induzida por Levedura Bioluminescente (BLYES), que apresentou-se como uma ferramenta simples. Os resultados apresentados neste trabalho demonstram que a oxidação por ozônio se mostrou mais eficiente do que aquela por cloro para a remoção da atividade estrogênica causada, única e exclusivamente, pelo 17β-estradiol para uma dosagem inicial desse hormônio relativamente alta (6.000 ng L-1). Todavia, em todos os ensaios a concentração final da atividade estrogênica permaneceu acima do limite de quantificação desses hormônio, indicando que a remoção não foi completa, mesmo em condições favoráveis, isto é, matriz limpa, com padrões de potabilidade para os parâmetros físico-químicos.