Corrosion of mild steel in different granularity seabed sediment saturated with seawater

In order to investigate the corrosion of pipeline materials in Seabed Sediment (SBS) environment, weight-loss and electrochemical measurements in saturated sand and mud cells with seawater were performed for a simulation. The used electrochemical measurements included linear polarization resistance (LPR) and potentiodynamic scanning measurement. It was showed that the corrosion rate of mild steel in the present condition was lower than the corrosion rate of other marine environment corrosion zones of it; that the granularity of SBS could affect the corrosion behavior greatly; that with increasing grain size of SBS, the corrosion rate increased. Integrated over the results of the weight loss and polarization curves, the oxygen diffusion (oxygen as a depolarizant agent) mechanism was proposed and discussed.

Study on steel corrosion in different seabed sediments

A series of simulation experiments on carbon steel (A(3) steel) and low alloy steel (16 Mn steel) in marine atmosphere (MA), seawater (SW) and seabed sediment (SBS) including rough sea sand, fine sea sand and seabed mud were carried out indoors for a year or so by means of individually hanging plates (IHP) and electrically connected hanging plates (ECHP). The corrosion of steels in SBS was mainly due to the macrogalvanic cell effect. The steel plates at the bottom of SBS, as the anode of a macrogalvanic cell, showed the heaviest corrosion with a corrosion rate of up to 0.12 mm/a, approximately equal to that of steel plates in marine atmosphere. The test results showed that the corrosion rates of A(3) and 16 Mn steel in marine environment were in the order: MA > SW > SBS by the IHP method; and MA > SBS > SW by the ECHP method. The corrosion rates of steels in the water/sediment interface were directly proportional to the grain size of the SBS by the ECHP method, but those of steels in the water/sediment interface did not vary with the grain size of SBS by the IHP method. The corrosion rate of low-alloy steel was a little higher than that of carbon steel. The results of this study have important applications for design of offshore steel structures such as oil platform, pier, and port.

蠕动爬行攻泥机构转向工作特性的有限元分析

针对用于沉船打捞的水下攻泥机器人蠕动爬行攻泥机构的结构与工作机理 ,建立了适当的有限元计算模型 ,进而通过弹塑性有限元计算 ,模拟了攻泥机构处于土中不同深度的工作情况 ,建立了攻泥机构前进位移V和转向角θ之间关系的通用公式。通过它可以实现对攻泥机构前进路线的规划与自动控制

用波动方程建立蠕动爬行攻泥机器人海底土力学运动模型

针对目前国内海底蠕动爬行机器人攻打千斤洞的特点 ,在对海洋沉积土的工程性质进行分析的基础上 ,利用流变力学的理论 ,提出用波动方程来建立攻泥机器人周期性冲击土壤的力学模型 ,用后向差分法解波动方程 ,得到土壤的位移和变形公式 ,确定土壤对攻泥机的阻力 .通过对模型的仿真 ,证明了用该模型计算阻力的可行性 .

砂泥岩储层测井产能预测方法研究

Productivity prediction is very important in the exploration and development of oilfields. Using well log data to predict productivity is a front-line technology， which is key issue in petroleum exploration phase. The essential factors of productivity prediction is building practical models and correcting various causes to improve precision of prediction parameters. Any errors of parameters selections can affect the calculation of productivity prediction; therefore， how to improve research means and calculation accuracy is an important task of productivity prediction. Theory and case examples are deeply and comprehensively studied in the paper. Based on the theory of mud-filtrate invasion and experimental results， the damage of drilling， cementing， perforating，acidizing and fracturing were investigated. The damage depth was quantitatively evaluated by log data， based on this， the processing results of reservoir sensitivity were used to analysis quantitatively the damage of reservoir. The productivity prediction and reservoir damage were initiatively incorporated according to well logging， and the precision of productivity prediction was effectively improved. The method of NMR was explored to calculate the fluid viscosity on the basis of reservoir physical method， and the differences between the two methods were compared in the paper. From the theory fluid flow in porous media， various of theoretical models of production prediction were explored and several practical models were consided， such as productivity index method， improved productivity index method， improved Bearder method， SVM and so on. The characteristic and the application scope of these methods were studied. The inflow productivity and outflow productivity were incorporated and nodal analysis method was used to forecast wellhead yield， thus achieved scientifically production. On the applied background of conventional logging suite， the applying of special items or new logging method which is practical in the research area were studied， the logging suite was further optimized， and the precision of forecast was improved. On the basis of the modeling and the calculation of parameters， these methods were verified and analyzed， and the reconstruct principle was also built for block reservoir. The research block was processed by these methods and compared with testing data. Based on above the research， a technological system which is practical for shaly sand profiles in Shengli Oilfield was built. The system can reach commercialized degree，and satisfied the need of exploration and development of the oilfield.

黄骅坳陷马东地区沙河街组重力流水道储层评价及剩余油研究

In this paper, taking Madong district of Huanghua depression as a case, based on the theory of sequence stratigraphy, sedimentology, reservoir geology and geophysics, according to core analysis, seismic attribute analysis, logging constrained inversion, multi-data correlation of strata, reservoir modeling, etc. the lower and middle first member of Shahejie formation of the study area was forecasted and evaluated. As a result, a number of reservoir prediction and remaining oil distribution methods suitable to oil exploitation of gravity flow channel reservoir are presented. Scientific foundation is provided to the next adjustment of development program and exploitation of the remaining oil. According to high resolution sequence stratigraphy theory, precise stratigraphic framework was founded, the facies types and facies distribution were studied under the control of stratigraphic framework, the technologies of seismic attribute abstraction and logging constrained inversion. Result shows that gravity flow channel, as the main facies, developed in the rising period of base-level cycle, and it was formed during the phase of contemporaneous fault growth. As the channel extends, channel width was gradually widened but thickness thined. The single channels were in possession of a great variety of integrated modes, such as isolated, branching off, merging and paralleling, forming a kind of sand-mud interblending complex sedimentary units. Reservoir quality differs greatly in vertical and horizontal direction, and sedimentary microfacies is main controlling factor of the reservoir quality. In major channel, deposition thickness is great, and petrophysical property is well. While in marginal channel, reservoir is thinner, and petrophysical property is unfavorable. Structure and reservoir quality are main factors which control the oil and gas distribution in the study area. On the basis of the research about the reservoir quality, internal, planar and 3-D reservoir heterogeneities are characterized, and the reservoir quality was sorted rationally. At last, based on the research of reservoir numerical simulation of key well group, combined with reservoir performance analysis and geological analysis above, remaining oil distribution patterns controlled by internal rhythm of gravity flow channel were set up. Through this research, a facies-restrained reservoir prediction method integrating multi-information was presented, and potential orientation of remaining oil distribution in gravity flow channel reservoir is clarified.

基于弹性参数分析的碳酸盐岩储层预测方法研究

Prediction of Carbonate Reservoir Based on the Elastic Parameter Analysis Zhang Guangzhi (Solid Geophysics) Directed by Professor Liu Hong Abstract With the exploration and development of Puguang Oilfield, oil-gas exploration of carbonate rock in China has shown good prospects. Research on earthquake prediction methods for carbonate reservoir becomes the key of oil and gas exploration. Starting with analysis of geological characteristics of carbonate rock, prestack AVO inversion method, prestack elastic impedance inversion and parameter calculation method and seismic attribute extraction and optimization method were studied based on the analysis of rock physics in this work. First, variation characteristic and law of carbonate rock reservoir parameters were studied based on experimental data of rock physics, log data, analysis assay data, mud logging data and seismic data, so as to lay a foundation for the further reservoir identification and description. Then, the structure, type and propagation law of seismic wave field were analyzed through seismic forward modeling of the reservoir, and contact between information from log and geology data with elastic parameters, such as compressional wave and shear wave velocity and density were established, so as to provide a standard for reservoir identification and hydrocarbon detection using seismic reflection characteristics of the research area. Starting with the general concept of inverse problem, through analysis of Zoeppritz equation, three kinds of pre-stack inversion methods were derived and analyzed in detail, the AVO 3-parameter inversion based on Bayesian theory, the prestack AVO waveform inversion method and the simultaneous inversion method, based on the statistical hypothesis of inversion parameters and observation data and the Gauss distribution assumption of noise. The three methods were validated by model data and real data. Then, the elastic wave impedance inversion method of carbonate reservoir was investigated and the method of elastic parameter extraction from elastic impedance data was put forward. Based on the analysis of conventional methods of seismic attribute extraction and optimization, the time-frequency attributes and the wavelet attributes with time and amplitude feature were presented, and the prestack seismic attribute calculation method which can characterize the reservoir rock and fluid characteristic was presented. And the optimization of seismic attribute using the nonlinear KPCA method was also put forward. A series of seismic prediction technologies for carbonate reservoir were presented based on analysis of rock physics and seismic forward simulation technology. Practical application of these technologies was implemented in A oil field of Southern China and good effect has been achieved. Key words: carbonate rock; reservoir prediction; rock physics, prestack seismic inversion; seismic attribute

元谋盆地河湖相沉积记录的上新世印度季风转型事件

The Indian monsoon, an integral part of the global climate system, has been extensively investigated during the past decades. Most of the proxy records are derived from marine sediments and focused on time periods of the late Miocene and Pleistocene. The Pliocene represents a period when Earth’s boundary conditions underwent dramatic changes. However, variations of the Indian monsoon during the Pliocene and its forcing mechanisms have remained unclear. The Yuanmou Basin, located in the region of the Indian monsoon, provides an ideal target for understanding the Pliocene history of Indian monsoon variations. Detailed investigations on the lithostratigraphy, magnetostratigraphy and limnology of a 650-m-thick fluvio-lacustrine sedimentary sequence from the basin are carried out in the present study. The clay and clay-plus-fine-silt fractions of the sediments are referred to the midlake-facies components, and changes in the percentages of both fractions generally reflect changes in the water level of the lakes developed in the basin closely related to variations in the intensity of the Indian monsoon. Whereas the greenish-gray lacustrine mud beds represent the environment of deep-water lakes, and the frequency of individual lacustrine mud beds is considered to indicate the frequency of the deep-water lakes developed in the basin associated with the variability of the Indian monsoon. The proxy data suggest that the Indian monsoon experienced abrupt shifts at 3.53, 3.14, 2.78 and 2.42 Ma, respectivey. 1) Since 3.53 Ma, the midlake-facies components displayed a general trend of increase in the concentrations, accompanied by an increase in the sedimentation rate from an average ~10 to 25 cm ka–1. The data suggest that high stands of the lakes in the basin rose progressively, implying a gradual intensification of the Indian monsoon since that time. This shift occurred coeval with the accelerated uplift of the northern Tibetan Plateau, denoting a close link between the Indian monsoon strengthening and the Tibetan Plateau uplifting. 2) 2.78 Ma ago, the concentrations of the midlake-facies components decreased abruptly and the dominant fraction of the sediments turned to fluvial sands. The data indicate that lakes in the basin disappeared, reflecting a dramatic decline in the intensity of the Indian monsoon at that time. This shift coincided with the formation of extensive Northern Hemisphere ice sheets, implying a quick response of the low-latitude monsoon regime to the high-latitude glaciation. 3) At 3.14 Ma, the initial appearance of blackish-grey mud beds with long durations and occasional occurrences of lacustrine mud beds indicate that the basin was overall dominated by shallow lakes, implying a shift to decreased variability of the Indian monsoon at that time. At 2.42 Ma, an increase in the frequency and a decrease in the duration of the lacustrine mud beds suggest that deep-water lakes were frequently developed in the basin, denoting a shift to increased variability of the Indian monsoon at that time. The former shift coincides with the onset of large-scale glaciation in the circum Atlantic region and the latter corresponds to the inception of predominance of the 41 ka periodicity in Northern Hemisphere ice-sheet cover fluctuations, presumably suggesting a physical link between the Indian monsoon system and the high-latitude ice sheets in the Northern Hemisphere.

鄂尔多斯盆地环县地区长6-长8沉积相及储层研究

The exploration in recent years shows that the Yanchang Formation in the southwest of Ordos Basin is of great resource potential and good exploration and exploitation prospect. In the thesis ，sedimentary source analysis，sedimentary system，sedimentary microfacies，sandstones distribution and reservoir characteristic are studied and favorable oil area are forecasted in Chang6-Chang8 of Yanchang formation in HuanXian region， by mainly study on the data of field section observation ，core observation, well logging explaination and routine microscope slice identification，scanning Electron Microscope and reservoir analysis of lithology and physical property , Under the guidance of such advanced theories and methods as sedimentology，reservoir sedimentology，lithological oil pool and so on. The stratum of Chang6-Chang8 of Yanchang formation could be divided into pieces of member following the principles that firstly contrasting the big segments, then contrasting the small segments, being controlled by cycle and consulting the thickness etc.And the characteristic of stratum are detailed discussed , respectively. Based on the source direction of the central basin, heavy and light minerals are used to analyse source direction of Chang6 and Chang8 member, in HuanXian area. Research result shows that the source of Chang6 and Chang8 member is mixed provenance,including west-south,west and east-north. By the study of rock types、 sedimentary conformation、lithology and electromotive curve combination and palaeo-biology,lake、delta and braided delta mianly developed in study area are recognized, Subaqueous distributary channels in delta front and in braided delta front, and sand body in deep-lake turbidite, are the main reservoir.forthermore,the characteristic of depositional system and sandy body in space are discussed. Applied with routine microscope slice identification, Scanning Electron Microscope, reservoir lithology and physical property analysis and other analytic machinery, Feldspar-lithic fine-sandstone and feldspar fine-sandstone are mainly sandstone of Y Chang6-Chang8 in Huanxian area, small pore and tiny pore are the main pore types, tiny throat type and micro-fine throat type are widely developed , secondary dissolution porosity, intercrystal porosity, tiny pore and micro-crack are main pore types.Intergranular porosity and dissolution porosity secondary is the main pore secondary. The dominant diagenesis types in the area are compaction, cementation, replacement and dissolution. Chlorite films cementation facies, carbonate cementation facies ,mud cementation compaction facie, compaction 、pressure solution facies are the main diagenetic facies,in which Chlorite films cementation facies is the best diagenetic facies in study area. Reservoir influence factor analysis ,rock types are the main factor forming this low-pore and low-permeability of Chang6-Chang8 member in study area,and relatively higher permeability area are cortrolled by sedimentary facies distribution, diagenesis improved reservoir physical property. According to the distributing of sedimentary micro-facies and sandy body , and the test oil, favorable region in Chang6-Chang8 are forecasted.

辽河盆地西部凹陷深部流体的地球化学特征与成藏效应

The main research area of this thesis is the Western Depression in the Liaohe Basin. Based on the drilling core observation and mud logging data, the features of the mantle–derived fluids and their effects on oil/gas generation in the Western Depression of the Liaohe Basin,was studied with comprehensive methods of volcanic petrology, sediment petrology, fluid geochemistry, sedimentlogy, and structural geology, and use of polarized light microscope, fluorescence microscope, electron microscope, fluid and melt inclusion test, and isotopic test of nature gas etc. The observation of drill cores in study area and other studies reveal that the main passageway of the volcanic eruption in the Cenozoic was the Xibaqian-Gaosheng fault, and the volcanic rocks of each stage were distributed around it. Mantle-derived fluid which affected on oil/gas generation formed later than the volcanic spew and those fluids entered into the depression through the Taian-Dawa fault and the Central fault. The volatile fraction analysis of the melt inclusion reveals the presence of two kinds of mantle fluids; they are hydrogen-rich fluid and carbon dioxide-rich fluid. These the two kinds of fluids were mainly distributed in olivine and pyroxene respectively. The hydrothermal veins development have multiple stages, from high temperature quartz vein to low temperature calcite vein and analcime vein, in which the fluid inclusion extremity component are methane and carbon dioxide, which indicate that when mantle-derived fluids ascended and entered into the basin, most of these fluids interacted with the organic matter in the basin even though some of these entered into atmosphere. The present isotopic test of the nature gas reveals the high 3He/4He value between the region of the Taian-Dawa fault and the Central fault, which also imply the feature of origin in mantle. This phenomenon indicates that the Mesozoic basement faults and the main Cenozoic faults had connected crust and the mantle during the basin evolution, so the mantle derived fluids could enter the basin along those faults. The main source rocks of the ES3 and ES4 members of the Shahejie Formation began to expel hydrocarbon at the end period of the ES1 member of the Shahejie Formation, and reached its peak during the period of the Dongying Formation deposition. During these periods, the mantle derived-fluids entered the basin constantly along the main faults, and supplied lots of hydrogen for hydrocarbon generation. Though the volcanic rocks and the mantle-derived fluids in the Eastern Depression were more developed than in the Western Depression, the source rocks and the deep fluids were not interacted better than the Western Depression because of the affection of structural evolution. In the Eocene, the Eastern Depression did not deposit the ES4 member of the Shahejie Formation, furthermore, the mantle-fluid formed in the Fangshengpao stage escaped to the atmosphere, which confined the later stage hydrocarbon generation capability.

AVO分析与地震资料叠前储层预测技术

In this paper we base on the anisotropic theory and Zoeppritz function of the transmission theory and the law of amplitude versus offset simplify seismic reflection coefficient of different media, analyze the characteristic of the gas or oil saturated stratum or the VTI and HTI models. Discuss the P wave reflection relationship and the meanings of the different parameters. We use measured parameters of a reservoir to simulate the characteristic of the reservoir, study the different effects of stratum saturated with gas or oil and analyze the characteristic of the seismic response of different models which change with different incident angles and different azimuths. Using the field data of logs ,analyze the rock property parameters, build the relationship of logs and parameters by Gassmann theory or empirical function. Calculate the density and the shear modulus and bulk modulus, reconstruct the log curves, calculate shear wave logs and correlate the logs affected by mud and other environmental factors. Finally perform the relationship of the seismic data log of saturated stratum and enhance the ability and reliability in reservoir prediction. Our aim is by the prestack seismic processing to get high solution and amplitude preserved seismic data. Because in incident angle gathers or azimuthal gathers, the low signal to noise ratio and low different covers affect the result of the prestack reservoir prediction. We apply prestack noise erase, cell regularization process and relatively amplitude preservation in the high solution seismic process routine to preserve the characteristic of stratum response, and erase the effects of the noise. In this paper we finished prestack invertion in the BYT survey and fractured reservoir depiction in MB survey. By the invertion and multiple attributes crossplot. we can get the stratum profiles and oil indicator profiles which can predict the distribution of the reservoir and oil. In the MB survey, we get orientation and density of fractured reservoir by the azimuthal seismic amplitude and depict the potential oil and gas reservoir. Prestak invertion works better in distinguishing oil and reservoir.

陕北何家集区延长组长4＋5－长6储层特征研究

Abstract： Hejiaji area lies on eastern part of Shanbei Slope in Ordos Basin and the primary oil-bearing bed is Chang 4＋5 and Chang 6 of Yanchang Formation. It is indicated that the sedimentary facies and reservoir characteristics restricted the hydrocarbon accumulation regularity by the geological information. Therefore, Applied with outcrop observation，core description, geophysical logging interpretation, thin section determination, Scanning Electron Microscope, reservoir lithology and physical property analysis and other analytic machinery, the sedimentary facies ,micro-characteristic and master control factors on hydrocarbon reservoir of Yanchang Formation in Hejiaji area are studied deeply by means of sedimentology，reservoir geology and petroleum geology and provide a reliably reference for later prospect . Delta facies are identified in Hejiaji area and of which distributary channels in delta plain microfacies controlled the distribution of sand bodies and accumulation of oil and gas.The distribution of sand bodies distributed from northeast to southwest are dominated by sedimentary facies . It was shown that the sandstones are medium to granule arkose，which the mud matrix is r and including，calcite，the content of matrix is lower and that mostly are cements which are mainly quartz and feldspar overgrowths and chlorite films, in the second place are hydromica and ferrocalcite. All the sandstones have entered a period of late diagenetic stage in which the dominant diagenesis types in the area are compaction, cementation and dissolution. Remnant intergranular porosity and feldspar dissolved pore are main pore types which are megalospore and medium pore. Medium-fine throat, fine throat and micro-fine throat are the mainly throat type. Pore texture can be classified as megalospore and fine throat type, medium-pore and micro-fine throat type mainly, and they are main accumulate interspace in research region. The reservoir of Yanchang Formation in Hejiaji area is low- pore and low- permeability in the mass which have strong heterogeneity in bed, interbedded and plane. Studying the parameter of pore and permeability comprehensively and consulting prevenient study results of evaluation of reservoir, the reservoir is classifiedⅡ，Ⅲ and Ⅳ three types in which the Ⅱand Ⅲ can be divided into Ⅱa and Ⅱb, Ⅲa and Ⅲb respectively. Ⅱb and Ⅲa are the main reservoir type in Hejiaji area which are about 72.73％and 80％percent of whole reservoir and effective reservoir respectively.

砂砾岩油藏精细油藏描述–以准噶尔盆地西北缘八区下乌尔禾组油藏为例

Glutenite reservoir is one of the most important reservoir types in china. Because of its particularity of rock structure and pore structure, it is usually difficult in development, especially for its serious heterogeneity. On the basis of seismic, well logs, core data and production performance, the lower Wuerhe group can be divided into one second-order sequences, two third-order sequences and twenty two subsequences, corresponding to the five stages and twenty two minlayers. In addition, the fault systems are interpreted and the control action of fault systems to reservoir development is also described. The lower Wuerhe formation of 8th district belongs to fluvial-dominated fan delta sedimentation, according to the analysis of well logs, logging data and core data. It can be subdivided into two kinds of subfacies and nine kinds of microfacies. The fan delta plain subfacies mainly consist of braided channel, unconcentrated flow, mud flow and sieve deposit microfacies. The fan delta front subfacies include subaqueous distributary channel, subaqueous interdistributary channel, debris flow, subaqueous barrier and grain flow microfacies. Combined with the regional geological characteristics, the porosity model of lower Wuerhe formation is performed using core data. A permeability model based on the flow zone index is also formed according to the pore throat characteristics and flow property. Finally, the heterogeneity is analyzed. The result shows that the lower Wuerhe formation has a feature of middle-high heterogeneity, and it is controlled by material sources and sedimentary facies belt.

松辽盆地南部大情字井地区CO2埋存体地质格架及储层建模

Increasing attentions have been paid to the subsurface geological storage for CO2 in view of the huge storage capacity of subsurface reservoirs. The basic requirement for subsurface CO2 storage is that the CO2 should be sequestrated as supercritical fluids (physical trapping), which may also interact with ambient reservoir rocks and formation waters, forming new minerals (chemical trapping). In order to the effective, durable and safe storage for CO2, enough storage space and stable sealing caprock with strong sealing capacity are necessitated, in an appropriate geological framework. Up till now, hydrocarbon reservoirs are to the most valid and appropriate CO2 storage container, which is well proven as the favorable compartment with huge storage capacity and sealing condition. The thesis focuses on two principal issues related to the storage and sealing capacity of storage compartment for the Qingshankou and Yaojia formations in the Daqingzijing block, Southern Songliao Basin, which was selected as the pilot well site for CO2-EOR storage. In the operation area, three facies, including deltaic plain, deltaic front and subdeep-deep lake facies associations, are recognized, in which 11 subfacies such as subaqueous distributary channel, river- mouth bar, interdistributary bay, sheet sandbody, crevasse splay and overflooding plain are further identified. These subfacies are the basic genetic units in the reservoir and sealing rocks. These facies further comprise the retrogradational and progradational depositional cycles, which were formed base- level rise and fall, respectively. During the regressive or lake lowstand stage, various sands including some turbidites and fans occurred mostly at the bottom of the hinged slope. During the progradation stage, these sands became smaller in size and episodically stepped backwards upon the slope, with greatly expanded and deeped lake. However, most of Cretaceous strata in the study area, localized in the basin centre under this stage, are mainly composed of grey or grizzly siltstones and grey or dark grey mudstones intercalated with minor fine sandstones and purple mudstones. On the base of borehole and core data, these siltstones are widespread, thin from 10 to 50 m thick, good grain sorting, and have relative mature sedimentary structures with graded bedding and cross- lamination or crossbeds such as ripples, which reflect strong hydrodynamic causes. Due to late diagenesis, pores are not widespread in the reservoirs, especially the first member of Qingshankou formation. There are two types of pores: primary pore and secondary cores. The primary pores include intergranular pores and micropores, and the secondary pores include emposieus and fracture pores. Throat channels related to pores is also small and the radius of throat in the first, second and third member of Qingshankou formation is only 0.757 μm, 0.802 μm and 0.631 μm respectively. In addition, based on analyzing the probability plot according to frequency of occurrence of porosity and permeability, they appear single- peaked distribution, which reflects strong hetero- geneity. All these facts indicate that the conditions of physical property of reservoirs are not better. One reason may be provided to interpret this question is that physical property of reservoirs in the study area is strong controlled by the depositional microfacies. From the statistics, the average porosity and permeability of microfacies such as subaqueous distributary channel, channel mouth bar, turbidites, is more than 9 percent and 1md respectively. On the contrary, the average porosity and permeability of microfacies including sand sheet, flagstone and crevasse splay are less than 9 percent and 0.2md respectively. Basically, different hydrodynamic environment under different microfacies can decide different physical property. According to the reservoir models of the first member of Qingshankou formation in the No. well Hei47 block, the character of sedimentary according to the facies models is accord to regional disposition evolution. Meantime, the parameter models of physical property of reservoir indicate that low porosity and low permeability reservoirs widespread widely in the study area, but the sand reservoirs located in the channels are better than other places and they are the main sand reservoirs. The distribution and sealing ability of fault- fractures and caprock are the key aspects to evaluate the stable conditions of compartments to store CO2 in the study area. Based on the core observation, the fractures widespread in the study area, especially around the wells, and most of them are located in the first and second member of Qingshankou formation, almost very few in the third member of Qingshankou formation and Yaojia formation instead. In addition, analyzing the sealing ability of eleven faults in the three-dimensional area in the study area demonstrates that most of faults have strong sealing ability, especially in the No. well Hei56 and Qing90-27. To some extent, the sealing ability of faults in the No. well Hei49, Qing4-6 and Qing84-29 are worse than others. Besides, the deposition environment of most of formations in the study area belongs to moderately deep and deep lake facies, which undoubtedly take advantage to caprocks composed of mudstones widespread and large scale under this deposition environment. In the study area, these mudstones distribute widely in the third member of Qingshankou formation, Yaojia and Nenjiang formation. The effective thickness of mudstone is nearly ~550m on an average with few or simple faults and fractures. In addition, there are many reservoir beds with widely- developed insulated interbeds consist of mudstones or silty mudstone, which can be the valid barrier to CO2 upper movement or leakage through diffusion, dispersion and convection. Above all, the closed thick mud caprock with underdeveloped fractures and reservoir beds can be taken regard as the favorable caprocks to provide stable conditions to avoid CO2 leakage.

塔里木盆地寒武－奥陶系白云岩类型、成因机理及其孔隙性研究

Cambrian-Ordovician dolostones in Tarim Basin are hydrocarbon reservoir rocks of vital importance. Under the guidance of the theories of sedimentology and the sedimentology of carbonate reservoir, based on the first-hand qualitative and quantitative data especially, combined with micro-study, geochemical and reservoir capacity analysis, and precursor research, the origin and reservoir characteristics of the dolostones were discussed. Based on detailed petrographic investigations, four types of dolostone have been recognized, which are, respecitively, mud-silt-sized dolostones, algal laminated dolostones (ALD), prophyritic dolostone, and neomorphic dolostone. Mud-silt-sized dolostones always presents as laminas together with evaporated signatures, its REE patterns and ΣREE are all close to that of the finely crystalline limestone. This kind of dolomite probably experienced relatively low fluid-rock ratio during diagenesis was formed in hypersaline and oxidizing environment and involved fast dolomitization process. It was dolomitized by evaporated seawater in sabkha environment.The main primary fabrics of algal lamination in algal laminated dolomite (ALD) can still be identified and its ΣREE (21.37) is very close to that of algae. This reveals that ALD was dolomitized during early diagenesis and algae possibly played an important role. The ALD was formed under mediation of organic matter and Mg2+ were supplied by magnesium concentrated algal laminites and sea water. Prophyritic dolostones presents mainly as patchy occurrence and yield the lowest δ13C and Z value. Its ΣREE is much less than that of the finely crystalline limestone. These characteristics reveal that the cloudy cores were dolomitized in shallow early diagenetic environments by pore fluids riched in Mg2+. Whereas the clear rims were likely formed in subsequent burial into deeper subsurface environments, and the Mg2+ needed for further dolomitization possibly was supplied by the transformations of clay minerals. Neomorphic dolostones consist of coarse, turbid crystals and exhibits sucrosic and mosaic textures. It has highest Fe2+ contents and average homogeneous temperature (110.2℃). Collectively, these characteristics demonstrate that the neomorphic dolostones was likely formed by recrystallization of pre-existing dolomites during deep burial. The ΣREE of the four types of dolostone distinctly differentiates from each other. However, their REE patterns are all enriched in LREE, depleted in HREE and have Eu negative anomalies. Its ΣREE 13.64 ppm, less than 1/4 of finely crystalline limestone, and ranks the lowest in the 4 types.These characteristics are comparable to those of finely crystalline limestone, and are mainly infuenced by the sea water. These four types of dolostone show similar REE mobility behaviour and no significant fractionation, althouth they have been subjected to evidently different diageneses. Seven main pore types are identified in the dolostones , which are fenestral, moldic, intercrystal, dissolved，breccia, dissolved breccia and stylolite pores. Fenestral pores are primary and the others are secondary. The dissolved pores and intercrystal pores are the most important reservoir spaces and followed by breccias and dissolved breccia pores, and the moldic and fenestral pores are less important. Stylolites can enhance permeability of reservoir rocks in one hand, for the other hand, the capacity of reservoir and permeability are enhanced and then better reservoir rocks can be formed when they are combined with patchy dolostones. The relationship between porosity and the type of dolostones is that the dissolved neomorphic dolostones have the highest porosity of 3.65%, than followed by dissolved Mud-silt-sized dolostones of 3.35%. The mud-silt-sized dolostones without dissolution have the lowest porosity of 0.90%. Moreover, the porosity of prophyritic dolostones and the neomorphic dolostones without dissolution are lower, respectively 1.675% and 1.41%. Although algal laminated dolostones consist of euhedral crystals and riched in intercrystal pores, its porosity just yields 1.20%. The relationship between permeability and the type of dolostones is that that algal laminated dolostones have the highest permeability of 0.462mD and followed by 0.065mD of prophyritic dolostones. Dissolution have no significant influence on the permeability of neomorphic dolostones and this presented by the permeability of dissolved and non-dissolved are very close, respectively 0.043mD and 0.062mD. No matter dissolved or not, mud-silt-sized dolostones are much less permeable. The permeability of non-dissolved and dissolved are 0.051mD and 0.016mD. Collectively, in the study area, neomorphic dolostones can form high quality reservoir.