Influência da geometria de corte no torneamento do eucalipto sp

In contrast to what happened in the past where it was possible to select which species had a lower degree of variation, it is now necessary to use fast-growing species with efficient processing. For that we use the wood of Eucalyptus sp and studies related to the machining processes and their parameters such as wear of cutting tools and roughness. The present work aims to analyze the influence of geometry of cutting tools of high speed steel and the influence of the diameter of the final pieces in the process of turning wood of Eucalyptus sp in relation to power consumption, roughness, temperature machining, chip formed and wear of cutting tools. It was observed that the smaller the diameter of the end parts and greater wear of the tools, the worse quality of the machined surfaces and the greater the power consumed in the process of machining

Aplicação do método desirability para otimização de processo com múltiplas respostas

Currently, the competition between organizations in the pursuit of consumer preference has become increasingly fierce. In addition, consumers have become increasingly demanding due to high speed with which innovations occur, leaving the companies meet and sometimes surpass those expectations In this context, there is the necessity to use methods as mathematical models capable of dealing with the optimization of multiple responses simultaneously. In this context, this study presents an application of techniques of Design of Experiment in a machining process of a NIMONIC 80 alloy, a “superalloy” that has thermal and mechanical properties that make its machining difficult and in order to do this, the Desirability Function was used. As they are determining conditions in the machining capability of the alloy, the roughness and the cutting length were considered as variable settings, and the factors that can influence them are cutting speed, feed rate, cutting depth, inserts type and lubrication. The analysis of the result pointed out how was the influence of all factors on each response and also showed the efficiency and reliability of the method

Efeitos do treinamento isocinético e isométrico sobre a taxa de desenvolvimento de força máxima

The objective of the present study was to compare the effects of a high speed isokinetic training (180°.s-1) and an isometric training (75°) on the maximum rate of force development (RFDmax) measured in the isokinetic and isometric modes. Twenty seven male non active subjects participated of this study (Mean + SD = body mass 78.6 + 14.1 kg; stature 175.1 + 8.9 cm; age 22.6 + 3.8 years). They were randomly divided into three groups: Control (GC); Isokinetic training (GISOC) and; Isometric training (GISOM). The subjects were submitted in different days to the following pre training protocols: 1) Familiarization to the isokinetic dynamometer tests; 2) Five maximum concentric isokinetic contractions of the knee extensors (180°.s-1) to access the maximum concentric torque (TMC) and the concentric RFDmax; 3) Two maximum isometric contractions of the knee extensors (75°) to access the maximum isometric torque (TMI) and the isometric RFDmax. The same tests were repeated after the training period, but without the familiarization session. Eighteen training sessions were performed (3 times per week). The GISOC performed the entire training whit concentric isokinetic contractions whit the speed of 180°.s-1. The GISOM performed the entire training whit isometric contractions whit the angle between the thigh end the leg being 75° (0° = full knee extension). TMI, TMC, concentric RFDmax, isometric RFDmax values of the GC was not different between pre and post training. GISOM increased only the TMI and the GSIOC increased the TMC, concentric RFDmax and isometric RFDmax. Furthermore, the GISOC had a higher percentage increase of the isometric RFDmax than the isokinetic RFDmax. Based on these results, it is possible to conclude that the increase in maximum strength corresponded to the training specificity theory, unlike to the RFDmax. Thus the use of isometric contraction ...(Complete abstract click electronic access below)

Treinamento de força unilateral: efeitos sobre a taxa de desenvolvimento de força do membro contralateral

The aim of this study was to analyze the effects of unilateral isokinetic strength training at high speed (180°.s-1) of the dominant leg on the rate of force development (RFD) of the contralateral limb. The study included 18 male individuals, apparently healthy, with an average of 23 years, and without regular practice of physical activities. The subjects were divided randomly into two groups: control group (GC) and isokinetic group (GISOC). Assessments were made of the values of peak isometric torque (PT isom) and RFD of both lower limbs in the pre-training. So, the GISOC underwent an isokinetic strength training with high speed (180°.s-1) for 6 weeks, with the dominant leg only and then reassessed. It was found that there was no significant improvement in value of PT isom (p> 0.05), and the RFD for the dominant limb had a significant improvement (p< 0.05) compared to the pre-training and that there was no transfer of values to the contralateral side (p> 0.05). It can be concluded that the isokinetic training at high speed was not enough for significant cross education

Estudo da deformação heterogênea no ensaio do anel de atrito

The plastic deformation is widely used in the metallurgical market due to its positive factors such as low prices and high speed production. Forming process products are obtained in high quality, both surface quality and mechanical properties. Friction is an importante factor in metal forming. Friction study in metal forming can be accomplished indirectly, such as the ring test of friction. Two samples of different materials being mild steel and copper alloy were used. The results showed the influence of friction in the flow behavior of the deformation of the second phase, as evidenced by standard metallography. It is observed that in the outer regions of the ring, plastic deformation occured in the radial direction. In the central region of the disc deformation occured in the direction of compression and the inner region of the ring flux lines showed a significant deformation in the radial direction towards the center of the ring

Bit-parallel coprocessor for standard ECC-GF(2m) on FPGA

This paper presents the design of a high-speed coprocessor for Elliptic Curve Cryptography over binary Galois Field (ECC- GF(2m)). The purpose of our coprocessor is to accelerate the scalar multiplication performed over elliptic curve points represented by affine coordinates in polynomial basis. Our method consists of using elliptic curve parameters over GF(2163) in accordance with international security requirements to implement a bit-parallel coprocessor on field-programmable gate-array (FPGA). Our coprocessor performs modular inversion by using a process based on the Stein's algorithm. Results are presented and compared to results of other related works. We conclude that our coprocessor is suitable for comparing with any other ECC-hardware proposal, since its speed is comparable to projective coordinate designs.

Analise comparativa do desempenho de ferramentas no torneamento do aluminio 2024

The aluminium alloys are used in many fields because of their versatility combined with the excellent aluminium’s properties, mentioned in the study. This study aims to compare the performance of polished Hard Metal, Hard Metal covered with TiB2 and High Speed Steel (HSS) tools, at the aluminium 2024 alloy’s turning, as a function of variation of some turning parameters such as: feed, depth of cut and cutting speed; and study the surface finish and the required power during turning by processing the output data, like analyze the chip’s features for each used tool. The results provide information of the tool’s material effects, when submitted to different turning conditions, about the output variable in question. In this way, it was possible to notice that although the Hard Metal covered with TiB2 tool has provided the better surface finish, the chip’s features were better when the turning was accomplished by the Polished Hard Metal tool. In relation to the required turning’s power, the lowest consumption occurred with the High Speed Steel tool

Usinabilidade e integridade superficial de implantes dentários

Pós-graduação em Engenharia Mecânica - FEIS

Resistência de união e microinfiltração em restaurações de resina

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Human teeth versus bovine teeth: cutting effectiviness of diamond burs

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Application of Er:YAG and Er, Cr:YSGG lasers in cavity preparation for dental tissues: a literature review

The laser has been widely used in many specialties of dentistry and several wavelengths have been investigated as a substitute for high-speed handpiece. The purpose of this paper is to review the literature about the use of Er:YAG and Er,Cr:YSGG lasers in cavity preparation for dental tissues. Despite the differences in wavelength, pulse duration and energy, the morphological characteristics of the irradiated dentin surface with these lasers are comparable, as well as its effects as methods of dental caries prevention. Thus, Er:YAG and Er,Cr:YSGG lasers prepared cavities with similar effects on the dental tissue, however, further investigations about ideal irradiation conditions are needed for both lasers.

Avaliação automatizada de uma habilidade motora fundamental com o kinect

Pós-graduação em Desenvolvimento Humano e Tecnologias - IBRC

Dinâmica não linear e projeto de controle em sistemas de transporte vertical: comportamentos periódicos e caóticos

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Efeito da suplementação com vitamina E sobre os metabolismos oxidativo e cardíaco em equinos submetidos a exercício de alta intensidade

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Simulação em tempo real de sistemas de distribuição de energia elétrica utilizando-se estruturas com descrição de hardware em software

Pós-graduação em Engenharia Elétrica - FEIS