Pull-through failure tests of thin steel roof battens under wind uplift load

Thin profiled steel roof sheeting and battens are increasingly used in the construction of roofing systems of residential, commercial, industrial and farm buildings in Australia. The critical load combination of external wind suction and internal wind pressures that occur during high wind events such as thunderstorms and tropical cylcones often dislocate the roofing systems partially or even completely due to premature roof connection failures. Past wind damage investigations have shown that roof sheeting failures occured at their screw connections to battens. In most of these cases, the screw fastener head pulled through the thin roof sheeting whilst the screw fasteners also pulled out from the battens. Research studis undertaken on the roof sheeting to batten connection failures have improved this situation. However, the batten to rafter or truss connections have not been investigated adequately. Failure of these connections can cause the failure of the entire roof structure as observed during the recent high wind events. Therefore a detailed experimental study consisting of both small scale and full scale tests has been undertaken to investigate the steel roof batten pull-through failures in relation to many critical parameters such as steel batten geometry, thickness and grade, screw fastener head sizes and screw tightening. This paper presents the details of this experimental study and the pull-through failure load results obtained from them. Finally it discusses the development of suitable design rules that can be used to determine the pull-through connection capacities of thin steel roof battens under wind uplift loads.

A simulator evaluation of effects of assistive technologies on driver cognitive load at railway level crossings

Intelligent Transport Systems (ITS) have the potential to substantially reduce the number of crashes caused by human errors at railway levels crossings. However, such systems could overwhelm drivers, generate different types of driver errors and have negative effects on safety at level crossing. The literature shows an increasing interest for new ITS for increasing driver situational awareness at level crossings, as well as evaluations of such new systems on compliance. To our knowledge, the potential negative effects of such technologies have not been comprehensively evaluated yet. This study aimed at assessing the effect of different ITS interventions, designed to enhance driver behaviour at railway crossings, on driver’s cognitive loads. Fifty eight participants took part in a driving simulator study in which three ITS devices were tested: an in-vehicle visual ITS, an in-vehicle audio ITS, and an on-road valet system. Driver cognitive load was objectively and subjectively assessed for each ITS intervention. Objective data were collected from a heart rate monitor and an eye tracker, while subjective data was collected with the NASA-TLX questionnaire. Overall, results indicated that the three trialled technologies did not result in significant changes in cognitive load while approaching crossings.

Investigation of drive-train dynamics of mechanical transmissions incorporating cycloidal drives

Cycloidal drives are compact, high-ratio gear transmission systems used in a wide range of mechanical applications from conveyor drives to articulated robots. This research hypothesises that these drives can be successfully applied in dynamic loading situations and thereby focuses on the understanding of differences between static and dynamic loading conditions where load varies with time. New methods of studying the behaviour of these drives under static and dynamic loading circumstances were developed, leading to novel understanding and knowledge. A new model was developed to facilitate research and development on Cycloidal drives with potential benefits for manufacturing, robotics and mechanical-process-industries worldwide.

Regulating ride-sharing in the peer economy

The rise of the peer economy poses complex new regulatory challenges for policy-makers. The peer economy, typified by services like Uber and AirBnB, promises substantial productivity gains through the more efficient use of existing resources and a marked reduction in regulatory overheads. These services are rapidly disrupting existing established markets, but the regulatory trade-offs they present are difficult to evaluate. In this paper, we examine the peer economy through the context of ride-sharing and the ongoing struggle over regulatory legitimacy between the taxi industry and new entrants Uber and Lyft. We first sketch the outlines of ride-sharing as a complex regulatory problem, showing how questions of efficiency are necessarily bound up in questions about levels of service, controls over pricing, and different approaches to setting, upholding, and enforcing standards. We outline the need for data-driven policy to understand the way that algorithmic systems work and what effects these might have in the medium to long term on measures of service quality, safety, labour relations, and equality. Finally, we discuss how the competition for legitimacy is not primarily being fought on utilitarian grounds, but is instead carried out within the context of a heated ideological battle between different conceptions of the role of the state and private firms as regulators. We ultimately argue that the key to understanding these regulatory challenges is to develop better conceptual models of the governance of complex systems by private actors and the available methods the state has of influencing their actions. These struggles are not, as is often thought, struggles between regulated and unregulated systems. The key to understanding these regulatory challenges is to better understand the important regulatory work carried out by powerful, centralised private firms – both the incumbents of existing markets and the disruptive network operators in the peer-economy.

Regulating ride-sharing in the peer economy

The rise of the peer economy poses complex new regulatory challenges for policy-makers. The peer economy, typified by services like Uber and AirBnB, promises substantial productivity gains through the more efficient use of existing resources and a marked reduction in regulatory overheads. These services are rapidly disrupting existing established markets, but the regulatory trade-offs they present are difficult to evaluate. In this paper, we examine the peer economy through the context of ride-sharing and the ongoing struggle over regulatory legitimacy between the taxi industry and new entrants Uber and Lyft. We first sketch the outlines of ride-sharing as a complex regulatory problem, showing how questions of efficiency are necessarily bound up in questions about levels of service, controls over pricing, and different approaches to setting, upholding, and enforcing standards. We outline the need for data-driven policy to understand the way that algorithmic systems work and what effects these might have in the medium to long term on measures of service quality, safety, labour relations, and equality. Finally, we discuss how the competition for legitimacy is not primarily being fought on utilitarian grounds, but is instead carried out within the context of a heated ideological battle between different conceptions of the role of the state and private firms as regulators. We ultimately argue that the key to understanding these regulatory challenges is to develop better conceptual models of the governance of complex systems by private actors and the available methods the state has of influencing their actions. These struggles are not, as is often thought, struggles between regulated and unregulated systems. The key to understanding these regulatory challenges is to better understand the important regulatory work carried out by powerful, centralised private firms – both the incumbents of existing markets and the disruptive network operators in the peer-economy.

Multi-rotor with suspended load: System dynamics and control toolbox

There is an increasing demand for Unmanned Aerial Systems (UAS) to carry suspended loads as this can provide significant benefits to several applications in agriculture, law enforcement and construction. The load impact on the underlying system dynamics should not be neglected as significant feedback forces may be induced on the vehicle during certain flight manoeuvres. The constant variation in operating point induced by the slung load also causes conventional controllers to demand increased control effort. Much research has focused on standard multi-rotor position and attitude control with and without a slung load. However, predictive control schemes, such as Nonlinear Model Predictive Control (NMPC), have not yet been fully explored. To this end, we present a novel controller for safe and precise operation of multi-rotors with heavy slung load in three dimensions. The paper describes a System Dynamics and Control Simulation Toolbox for use with MATLAB/SIMULINK which includes a detailed simulation of the multi-rotor and slung load as well as a predictive controller to manage the nonlinear dynamics whilst accounting for system constraints. It is demonstrated that the controller simultaneously tracks specified waypoints and actively damps large slung load oscillations. A linear-quadratic regulator (LQR) is derived and control performance is compared. Results show the improved performance of the predictive controller for a larger flight envelope, including aggressive manoeuvres and large slung load displacements. The computational cost remains relatively small, amenable to practical implementations.

Japonica rice: Intellectual property, scientific publishing and data-sharing

This article examines a series of controversies within the life sciences over data sharing. Part 1 focuses upon the agricultural biotechnology firm Syngenta publishing data on the rice genome in the journal Science, and considers proposals to reform scientific publishing and funding to encourage data sharing. Part 2 examines the relationship between intellectual property rights and scientific publishing, in particular copyright protection of databases, and evaluates the declaration of the Human Genome Organisation that genomic databases should be global public goods. Part 3 looks at varying opinions on the information function of patent law, and then considers the proposals of Patrinos and Drell to provide incentives for private corporations to release data into the public domain.

Treatment of proximal interphalangeal joint flexion contracture: Combined static and dynamic orthotic intervention compared with other therapy intervention: randomized controlled trial

Purpose To test the effectiveness of static and dynamic orthoses using them as an exclusive treatment for proximal interphalangeal (PIP) joint flexion contracture compared with other hand therapy conservative treatments described in the literature. Methods 60 patients who used orthoses were compared with a control group that received other hand therapy treatments. Clinical assessments were measured before the experiment and 3 months after and included active PIP joint extension and function. Results A significant improvement in the extension active range of motion at the PIP joint in the second measurement was found in both groups, but it was significantly greater in the experimental group. Improvement in function (Disabilities of the Arm, Shoulder, and Hand score) between the first and second assessment was similar in the control and experimental groups. Conclusions Using night progressive static and daily dynamic orthoses as an exclusive treatment during the proliferative phase led to significant improvements in the PIP joint active extension, but the improvement did not correlate with increased function as perceived by the patient.

Information encountering on social media and tacit knowledge sharing

The purpose of this paper is to investigate how social media may support information encountering (i.e., where individuals encounter useful and interesting information while seeking or browsing for some other information) and how this may lead to facilitation of tacit knowledge creation and sharing. The study employed a qualitative survey design that interviewed twenty-four physicians who were active users of social media to better understand the phenomenon of information encountering on social media. The data was analysed using the thematic analysis approach. The study found six main ways through which social media supports information encountering. Furthermore, drawing upon knowledge creation theories, the study concluded that information encountering on social media facilitates tacit knowledge creation and sharing among individuals. The study provides new directions for further empirical investigations to examine whether information encountering on social media actually leads to tacit knowledge creation and sharing. The findings of the study may also provide opportunities for users to adopt social media effectively or gain greater value from social media use.

Assessment of dynamic susceptibility contrast cerebral blood flow response to amphetamine challenge: A human pharmacological magnetic resonance imaging study at 1.5 and 4 T

Pharmacological MRI (phMRI) techniques can be used to monitor the neurophysiological effects of central nervous system (CNS) active drugs. In this study, we investigated whether dynamic susceptibility contrast (DSC) perfusion imaging employing the use of superparamagnetic iron oxide nanoparticles (Resovist) could be used to measure hemodynamic response to d-amphetamine challenge in human subjects at both 1.5 and 4 T. Significant changes in cerebral blood flow (CBF) were found in focal regions associated with the nigrostriatal circuit and mesolimbic and mesocortical dopaminergic pathways. More significant CBF responses were found at higher field strength, mainly within striatal structures. The results from this study indicate that DSC perfusion imaging using Resovist can be used to assess the efficacy of CNS-active drugs and may play a role in the development of novel psychiatric therapies at the preclinical level. © 2005 Wiley-Liss, Inc.

Connected Viewing: Selling, Streaming and Sharing Media in the Digital Era

As patterns of media use become more integrated with mobile technologies and multiple screens, a new mode of viewer engagement has emerged in the form of connected viewing, which allows for an array of new relationships between audiences and media texts in the digital space. This exciting new collection brings together twelve original essays that critically engage with the socially-networked, multi-platform, and cloud-based world of today, examining the connected viewing phenomenon across television, film, video games, and social media. The result is a wide-ranging analysis of shifting business models, policy matters, technological infrastructure, new forms of user engagement, and other key trends affecting screen media in the digital era. Connected Viewing contextualizes the dramatic transformations taking place across both media industries and national contexts, and offers students and scholars alike a diverse set of methods and perspectives for studying this critical moment in media culture.

Web crippling tests of rivet fastened rectangular hollow flange channel beams under two flange load cases

Recent research on hollow flange beams has led to the development of an innovative rectangular hollow flange channel beam (RHFCB) for use in floor systems. The new RHFCB is a mono-symmetric structural section made by intermittently rivet fastening two torsionally rigid closed rectangular hollow flanges to a web plate element, which allows section optimisation by selecting appropriate combinations of web and flange widths and thicknesses. However, the current design rules for cold-formed steel sections are not directly applicable to rivet fastened RHFCBs. To date, no investigation has been conducted on their web crippling behaviour and strengths. Hence an experimental study was conducted to investigate the web crippling behaviour and capacities of rivet fastened RHFCBs under End Two Flange (ETF) and Interior Two Flange (ITF) load cases. It showed that RHFCBs failed by web crippling, flange crushing and their combinations. Comparison of ultimate web crippling capacities with the predictions from the design equations in AS/NZS 4600 and AISI S100 showed that the current design equations are unconservative for rivet fastened RHFCB sections under ETF and ITF load cases. Hence new equations were proposed to determine the web crippling capacities of rivet fastened RHFCBs. These equations can also be used to predict the capacities of RHFCBs subject to combined web crippling and flange crushing conservatively. However, new capacity equations were proposed in the case of flange crushing failures that occurred in thinner flanges with smaller bearing lengths. This paper presents the details of this web crippling experimental study of RHFCB sections and the results.

Optimum position of steel outrigger system for high rise composite buildings subjected to wind loads

The responses of composite buildings under wind loads clearly become more critical as the building becomes taller, less stiff and more lightweight. When the composite building increases in height, the stiffness of the structure becomes more important factor and introduction to belt truss and outrigger system is often used to provide sufficient lateral stiffness to the structure. Most of the research works to date is limited to reinforced concrete building with outrigger system of concrete structure, simple building plan layout, single height of a building, one direction wind and single level of outrigger arrangement. There is a scarcity in research works about the effective position of outrigger level on composite buildings under lateral wind loadings when the building plan layout, height and outrigger arrangement are varied. The aim of this paper is to determine the optimum location of steel belt and outrigger systems by using different arrangement of single and double level outrigger for different size, shape and height of composite building. In this study a comprehensive finite element modelling of composite building prototypes is carried out, with three different layouts (Rectangular, Octagonal and L shaped) and for three different storey (28, 42 and 57-storey). Models are analysed for dynamic cyclonic wind loads with various combination of steel belt and outrigger bracings. It is concluded that the effectiveness of the single and double level steel belt and outrigger bracing are varied based on their positions for different size, shape and height of composite building.

Computer analysis of impact behavior of concrete filled steel tube columns

This paper presents a numerical study of the response of axially loaded concrete filled steel tube (CFST) columns under lateral impact loading using explicit non-linear finite element techniques. The aims of this paper are to evaluate the vulnerability of existing columns to credible impact events as well as to contribute new information towards the safe design of such vulnerable columns. The model incorporates concrete confinement, strain rate effects of steel and concrete, contact between the steel tube and concrete and dynamic relaxation for pre-loading, which is a relatively recent method for applying a pre-loading in the explicit solver. The finite element model was first verified by comparing results with existing experimental results and then employed to conduct a parametric sensitivity analysis. The effects of various structural and load parameters on the impact response of the CFST column were evaluated to identify the key controlling factors. Overall, the major parameters which influence the impact response of the column are the steel tube thickness to diameter ratio, the slenderness ratio and the impact velocity. The findings of this study will enhance the current state of knowledge in this area and can serve as a benchmark reference for future analysis and design of CFST columns under lateral impact.

A dynamic real time scheduling methodology for the emergency department

This project constructs a scheduling solution for the Emergency Department. The schedules are generated in real-time to adapt to new patient arrivals and changing conditions. An integrated scheduling formulation assigns patients to beds and treatment tasks to resources. The schedule efficiency is assessed using waiting time and total care time experienced by patients. The solution algorithm incorporates dispatch rules, meta-heuristics and a new extended disjunctive graph formulation which provide high quality solutions in a fast time-frame for real time decision support. This algorithm can be implemented in an electronic patient management system to improve patient flow in the Emergency Department.