Cu2ZnSnS4 absorber layers obtained through sulphurization of metallic precursors: Graphite box versus sulphur flux

In this work we employed a hybrid method, combining RF-magnetron sputtering with evaporation, for the deposition of tailor made metallic precursors, with varying number of Zn/Sn/Cu (ZTC) periods and compared two approaches to sulphurization. Two series of samples with 1×, 2× and 4× ZTC periods have been prepared. One series of precursors was sulphurized in a tubular furnace directly exposed to a sulphur vapour and N2+5% H2 flux at a pressure of 5.0×10+4 Pa. A second series of identical precursors was sulphurized in the same furnace but inside a graphite box where sulphur pellets have been evaporated again in the presence of N2+5% H2 and at the same pressure as for the sulphur flux experiments. The morphological and chemical analyses revealed a small grain structure but good average composition for all three films sulphurized in the graphite box. As for the three films sulphurized in sulphur flux grain growth was seen with the increase of the number of ZTC periods whilst, in terms of composition, they were slightly Zn poor. The films' crystal structure showed that Cu2ZnSnS4 is the dominant phase. However, in the case of the sulphur flux films SnS2 was also detected. Photoluminescence spectroscopy studies showed an asymmetric broad band emission whichoccurs in the range of 1–1.5 eV. Clearly the radiative recombination efficiency is higher in the series of samples sulphurized in sulphur flux. We have found that sulphurization in sulphur flux leads to better film morphology than when the process is carried out in a graphite box in similar thermodynamic conditions. Solar cells have been prepared and characterized showing a correlation between improved film morphology and cell performance. The best cells achieved an efficiency of 2.4%.

Influence of selenization pressure on the growth of Cu2ZnSnSe4 films from stacked metallic layers

Cu2ZnSnSe4 (CZTSe) is a p-type semiconductor with a high absorption coefficient, 104 to 105 cm-1, and is being seen as a possible replacement for Cu(In,Ga)Se2 in thin film solar cells. Yet, there are some fundamental properties of CZTSe that are not well known, one of them is its band gap. In order to resolve its correct value it is necessary to improve the growth conditions to ensure that single phase crystalline thin films are obtained. One of the problems encountered when growing CZTSe is the loss of Sn through evaporation of SnSe. Stoichiometric films are then difficult to obtain and usually there are other phases present. One possible way to overcome this problem is to increase the pressure of growth of CZTSe. This can be done by introducing an atmosphere of an inert gas like Ar or N2. In this work we report the results of morphological, structural and optical studies of the properties of CZTSe thin films grown by selenization of DC magnetron sputtered metallic layers under different Ar pressures. The films are analysed by SEM/EDS, Raman scattering and XRD.

Novos compostos orgânicos reticuláveis para aplicações em células fotovoltaicas

Trabalho Final de Mestrado para obtenção do grau de mestre em Engenharia Química e Biológica

Al-doped ZnO ceramic sputtering targets based on nanocrystalline powders produced by emulsion detonation synthesis – deposition and application as a transparent conductive oxide material

Transparent conducting oxides (TCOs) have been largely used in the optoelectronic industry due to their singular combination of low electrical resistivity and high optical transmittance. They are usually deposited by magnetron sputtering systems being applied in several devices, specifically thin film solar cells (TFSCs). Sputtering targets are crucial components of the sputtering process, with many of the sputtered films properties dependent on the targets characteristics. The present thesis focuses on the development of high quality conductive Al-doped ZnO (AZO) ceramic sputtering targets based on nanostructured powders produced by emulsion detonation synthesis method (EDSM), and their application as a TCO. In this sense, the influence of several processing parameters was investigated from the targets raw-materials synthesis to the application of sputtered films in optoelectronic devices. The optimized manufactured AZO targets present a final density above 99 % with controlled grain size, an homogeneous microstructure with a well dispersed ZnAl2O4 spinel phase, and electrical resistivities of ~4 × 10-4 Ωcm independently on the Al-doping level among 0.5 and 2.0 wt. % Al2O3. Sintering conditions proved to have a great influence on the properties of the targets and their performance as a sputtering target. It was demonstrated that both deposition process and final properties of the films are related with the targets characteristics, which in turn depends on the initial powder properties. In parallel, the influence of several deposition parameters in the film´s properties sputtered from these targets was investigated. The sputtered AZO TCOs showed electrical properties at room temperature that are superior to simple oxides and comparable to a reference TCO – indium tin oxide (ITO), namely low electrical resistivity of 5.45 × 10-4 Ωcm, high carrier mobility (29.4 cm2V-1s-1), and high charge carrier concentration (3.97 × 1020 cm-3), and also average transmittance in the visible region > 80 %. These superior properties allowed their successful application in different optoelectronic devices.

The role of GAPDH in maintaining the functional state of the DNA repair enzyme APE1

Les sites apuriniques/apyrimidiniques (AP) sont des sites de l’ADN hautement mutagène. Les dommages au niveau de ces sites peuvent survenir spontanément ou être induits par une variété d’agents. Chez l’humain, les sites AP sont réparés principalement par APE1, une enzyme de réparation de l’ADN qui fait partie de la voie de réparation par excision de base (BER). APE1 est une enzyme multifonctionnelle; c’est une AP endonucléase, 3’-diestérase et un facteur redox impliqué dans l’activation des facteurs de transcription. Récemment, il a été démontré qu’APE1 interagit avec l’enzyme glycolytique GAPDH. Cette interaction induit l’activation d’APE1 par réduction. En outre, la délétion du gène GAPDH sensibilise les cellules aux agents endommageant l’ADN, induit une augmentation de formation spontanée des sites AP et réduit la prolifération cellulaire. A partir de toutes ces données, il était donc intéressant d’étudier l’effet de la délétion de GAPDH sur la progression du cycle cellulaire, sur la distribution cellulaire d’APE1 et d’identifier la cystéine(s) d’APE1 cible(s) de la réduction par GAPDH. Nos travaux de recherche ont montré que la déficience en GAPDH cause un arrêt du cycle cellulaire en phase G1. Cet arrêt est probablement dû à l’accumulation des dommages engendrant un retard au cours duquel la cellule pourra réparer son ADN. De plus, nous avons observé des foci nucléaires dans les cellules déficientes en GAPDH qui peuvent représenter des agrégats d’APE1 sous sa forme oxydée ou bien des focis de la protéine inactive au niveau des lésions d’ADN. Nous avons utilisé la mutagénèse dirigée pour créer des mutants (Cys en Ala) des sept cystéines d’APE1 qui ont été cloné dans un vecteur d’expression dans les cellules de mammifères. Nous émettons l’hypothèse qu’au moins un mutant ou plus va être résistant à l’inactivation par oxydation puisque l’alanine ne peut pas s’engager dans la formation des ponts disulfures. Par conséquent, on anticipe que l’expression de ce mutant dans les cellules déficientes en GAPDH pourrait restaurer une distribution cellulaire normale de APE1, libérerait les cellules de l’arrêt en phase G1 et diminuerait la sensibilité aux agents endommageant l’ADN. En conclusion, il semble que GAPDH, en préservant l’activité d’APE1, joue un nouveau rôle pour maintenir l’intégrité génomique des cellules aussi bien dans les conditions normales qu’en réponse au stress oxydatif.

Étude ab initio des propriétés électroniques de polymères conjugués et de cristaux moléculaires

Mémoire numérisé par la Division de la gestion de documents et des archives de l'Université de Montréal

Développement de composés conjugués en étoile de première génération incluant des liens azométhines et études électrochimiques et photophysiques

Les matériaux conjugués sont de nos jours très utilisés dans de nombreuses applications ainsi qu’en recherche. L’enchainement des liaisons π-σ-π permet la délocalisation des électrons et d’obtenir différentes propriétés comme la conduction, la fluorescence, la chélation, etc. Ainsi, de nombreux dispositifs utilisent ces caractéristiques en vue d’obtenir de nouveaux matériaux révolutionnaires comme les cellules solaires, les transistors à effet de champs, les dispositifs électrochromiques, etc.. Les dispositifs électrochromiques font partie des dispositifs en vogue. Ils sont capables de changer de couleur selon le potentiel électrique appliqué. Ils se distinguent par la simplicité du mode de conception et ils ne nécessitent pas de fonctionner dans des conditions drastiques comme une atmosphère contrôlée. Ces dispositifs sont actuellement utilisés et commercialisés comme fenêtre intelligente, camouflage, papier électronique et carte de visite personnalisée pour n’en nommer que quelques-uns. Deux propriétés sont essentielles pour que des composés puissent être utilisés dans ces familles de dispositifs : la réversibilité à l’oxydation et la stabilité à l’air et à la lumière. Dans le groupe de recherche du professeur W.G. Skene, l’axe principal de recherche est basé sur la conception de nouveaux matériaux conducteurs comportant des liaisons azométhines. Les principaux matériaux étudiés sont des dérivés de thiophènes et de fluorènes. De précédents résultats ont montré que plusieurs produits issus de la réaction de condensation entre les dérivés du 2,5-diaminothiophène et de thiophènes diformylés menaient à des produits possédant d’excellentes propriétés photophysiques et électrochimiques. C’est en partant de ces résultats encourageants qu’il a été choisi de synthétiser une nouvelle famille de produits avec un nouveau substrat fonctionnalisé. Ce dernier possède d’excellentes propriétés électrochimiques et photophysiques : la triphénylamine. Deux familles de produits ont été synthétisées qui possèdent toutes comme cœur une triphénylamine. Cette dernière a été modifiée de façon à créer une, deux ou trois liaisons azométhines avec différents thiophènes. Deux dérivés du thiophène ont été choisis afin d’étudier l’influence des groupements donneurs et accepteurs sur ces nouveaux types de composés encore jamais étudiés. Les résultats des différentes synthèses et analyses ont été effectués par RMN, spectrométrie de masse, spectrométrie d’absorbance UV-Visible, fluorescence et voltampérométrie cyclique sont rapportées dans le présent recueil.

Calculs ab initio de structures électroniques pour un meilleur design de polymères photovoltaïques

La présente thèse porte sur l'utilité de la théorie de la fonctionnelle de la densité dans le design de polymères pour applications photovoltaïques. L'étude porte d'abord sur le rôle des calculs théoriques pour la caractérisation des polymères dans le cadre de collaborations entre la théorie et l'expérience. La stabilité et les niveaux énergétiques de certaines molécules organiques sont étudiés avant et après la sulfuration de leurs groupements carbonyles, un procédé destiné à diminuer le band gap. Les propriétés de dynamique électronique, de séparation des porteurs de charges et de spectres de vibrations Raman sont également explorées dans un polymère à base de polycarbazole. Par la suite, l'utilité des calculs théoriques dans le design de polymères avant leurs synthèses est considérée. La théorie de la fonctionnelle de la densité est étudiée dans le cadre du modèle de Scharber afin de prédire l'efficacité des cellules solaires organiques. Une nouvelle méthode de design de polymères à faible band gaps, basée sur la forme structurale aromatique ou quinoide est également présentée, dont l'efficacité surpasse l'approche actuelle de donneur-accepteur. Ces études sont mises à profit dans l'exploration de l'espace moléculaire et plusieurs candidats de polymères aux propriétés électroniques intéressantes sont présentés.

Signature optique d’effet Stark dans une bicouche de CuPc:C60

Les hétérojonctions formées de deux matériaux, un donneur et un accepteur (D/A), sont la base de la majorité des mélanges photovoltaïques organiques. Les mécanismes de séparation des charges dans ces systèmes représentent aujourd'hui l'un des sujets les plus chauds et les plus débattus dans ce domaine. Nous entrons au coeur de ce débat en choisissant un système D/A à base de phtalocyanine de cuivre (CuPc) et de fullerène (C60). Pour sonder les états excités de nos molécules et obtenir de l'information sur les phénomènes à l'interface D/A, nous réalisons une expérience pompe-sonde, appelée absorption photoinduite (PIA). Nous y mesurons le changement fractionnaire de transmission au travers de l'échantillon. Les mesures de PIA sont réalisées à l'état de quasi équilibre, à T=10K. Nous observons une modulation prononcée dans la région du photoblanchiment de l'état fondamental qui nous indique que la pompe induit un décalage du spectre d'absorption de l'état fondamental. Ce décalage peut être expliqué par deux processus : soit l'échantillon est chauffé par la pompe (effet thermique) ou bien des charges sont créées à l'interface entre les deux matériaux (effet Stark). La dépendance en température du spectre d'absorption entre 10K et 290K montre une signature thermique pour un changement de température de 80K. Grâce au ratio des raies Raman anti-Stokes et Stokes, nous démontrons que la pompe chauffe l'échantillon de 34 K, température insuffisante pour attribuer notre signal à un effet thermique. Nous évaporons ensuite la bicouche CuPc/C60 sur de l'ITO et du saphir, substrats qui possèdent des conductivités thermiques différentes et nous observons le même signal de PIA, excluant par le fait même l'hypothèse de l'effet thermique. Puisque notre étude est comparable à la spectroscopie à effet Stark, nous procédons à une analyse similaire en comparant notre signal de PIA au spectre de la transmittance et à ses dérivés première et seconde. Nous observons alors que notre signal reproduit presque parfaitement la dérivée seconde de la transmittance. Ces résultats sont conformes à une signature optique d'effet Stark due à la création de charges à l'interface D/A.

Non-Destructive Evaluation of Ion-Implanted Semiconductor Thin Films Using Photothermal Deflections Spectroscopy

Materials and equipment which fail to achieve the design requirements or projected life due to undetected defects may require expensive repair or early replacement. Such defects may also be the cause of unsafe conditions or catastrophic unexpected failure, and will lead to loss of revenue due to plant shutdown. Non-Destructive Evaluation (NDE) / Non Destructive Testing (NDT) is used for the examination of materials and components without changing or destroying their usefulness. NDT can be applied to each stage of a system’s construction, to monitor the integrity of the system or structure throughout its life.

Spray Pyrolysed Zinc Oxide Thin Films : Effects of Doping and Ion Beam Irradiation

In recent years scientists have made rapid and significant advances in the field of semiconductor physics. One of the most important fields of current interest in materials science is the fundamental aspects and applications of conducting transparent oxide thin films (TCO). The characteristic properties of such coatings are low electrical resistivity and high transparency in the visible region. The first semitransparent and electrically conducting CdO film was reported as early as in 1907 [1]. Though early work on these films was performed out of purely scientific interest, substantial technological advances in such films were made after 1940. The technological interest in the study of transparent semiconducting films was generated mainly due to the potential applications of these materials both in industry and research. Such films demonstrated their utility as transparent electrical heaters for windscreens in the aircraft industry. However, during the last decade, these conducting transparent films have been widely used in a variety of other applications such as gas sensors [2], solar cells [3], heat reflectors [4], light emitting devices [5] and laser damage resistant coatings in high power laser technology [6]. Just a few materials dominate the current TCO industry and the two dominant markets for TCO’s are in architectural applications and flat panel displays. The architectural use of TCO is for energy efficient windows. Fluorine doped tin oxide (FTO), deposited using a pyrolysis process is the TCO usually finds maximum application. SnO2 also finds application ad coatings for windows, which are efficient in preventing radiative heat loss, due to low emissivity (0.16). Pyrolitic tin oxide is used in PV modules, touch screens and plasma displays. However indium tin oxide (ITO) is mostly used in the majority of flat panel display (FPD) applications. In FPDs, the basic function of ITO is as transparent electrodes. The volume of FPD’s produced, and hence the volume of ITO coatings produced, continues to grow rapidly. But the current increase in the cost of indium and the scarcity of this material created the difficulty in obtaining low cost TCOs. Hence search for alternative TCO materials has been a topic of active research for the last few decades. This resulted in the development of binary materials like ZnO, SnO2, CdO and ternary materials like II Zn2SnO4, CdSb2O6:Y, ZnSO3, GaInO3 etc. The use of multicomponent oxide materials makes it possible to have TCO films suitable for specialized applications because by altering their chemical compositions, one can control the electrical, optical, chemical and physical properties. But the advantages of using binary materials are the easiness to control the chemical compositions and depositions conditions. Recently, there were reports claiming the deposition of CdO:In films with a resistivity of the order of 10-5 ohm cm for flat panel displays and solar cells. However they find limited use because of Cd-Toxicity. In this regard, ZnO films developed in 1980s, are very useful as these use Zn, an abundant, inexpensive and nontoxic material. Resistivity of this material is still not very low, but can be reduced through doping with group-III elements like In, Al or Ga or with F [6]. Hence there is a great interest in ZnO as an alternative of ITO. In the present study, we prepared and characterized transparent and conducting ZnO thin films, using a cost effective technique viz Chemical Spray Pyrolysis (CSP). This technique is also suitable for large area film deposition. It involves spraying a solution, (usually aqueous) containing soluble salts of the constituents of the desired compound, onto a heated substrate.

Growth and Characterisation of Radio Frequency Magnetron Sputttered Indium Tin Oxide Thin Films

The increasing interest in the interaction of light with electricity and electronically active materials made the materials and techniques for producing semitransparent electrically conducting films particularly attractive. Transparent conductors have found major applications in a number of electronic and optoelectronic devices including resistors, transparent heating elements, antistatic and electromagnetic shield coatings, transparent electrode for solar cells, antireflection coatings, heat reflecting mirrors in glass windows and many other. Tin doped indium oxide (indium tin oxide or ITO) is one of the most commonly used transparent conducting oxides. At present and likely well into the future this material offers best available performance in terms of conductivity and transmittivity combined with excellent environmental stability, reproducibility and good surface morphology. Although partial transparency, with a reduction in conductivity, can be obtained for very thin metallic films, high transparency and simultaneously high conductivity cannot be attained in intrinsic stoichiometric materials. The only way this can be achieved is by creating electron degeneracy in a wide bandgap (Eg > 3eV or more for visible radiation) material by controllably introducing non-stoichiometry and/or appropriate dopants. These conditions can be conveniently met for ITO as well as a number of other materials like Zinc oxide, Cadmium oxide etc. ITO shows interesting and technologically important combination of properties viz high luminous transmittance, high IR reflectance, good electrical conductivity, excellent substrate adherence and chemical inertness. ITO is a key part of solar cells, window coatings, energy efficient buildings, and flat panel displays. In solar cells, ITO can be the transparent, conducting top layer that lets light into the cell to shine the junction and lets electricity flow out. Improving the ITO layer can help improve the solar cell efficiency. A transparent ii conducting oxide is a material with high transparency in a derived part of the spectrum and high electrical conductivity. Beyond these key properties of transparent conducting oxides (TCOs), ITO has a number of other key characteristics. The structure of ITO can be amorphous, crystalline, or mixed, depending on the deposition temperature and atmosphere. The electro-optical properties are a function of the crystallinity of the material. In general, ITO deposited at room temperature is amorphous, and ITO deposited at higher temperatures is crystalline. Depositing at high temperatures is more expensive than at room temperature, and this method may not be compatible with the underlying devices. The main objective of this thesis work is to optimise the growth conditions of Indium tin oxide thin films at low processing temperatures. The films are prepared by radio frequency magnetron sputtering under various deposition conditions. The films are also deposited on to flexible substrates by employing bias sputtering technique. The films thus grown were characterised using different tools. A powder x-ray diffractometer was used to analyse the crystalline nature of the films. The energy dispersive x-ray analysis (EDX) and scanning electron microscopy (SEM) were used for evaluating the composition and morphology of the films. Optical properties were investigated using the UVVIS- NIR spectrophotometer by recording the transmission/absorption spectra. The electrical properties were studied using vander Pauw four probe technique. The plasma generated during the sputtering of the ITO target was analysed using Langmuir probe and optical emission spectral studies.

Preparation and characterisation of certain II-VI, I-III-VI2 semiconductor thin films and transparent conducting oxides

There is an increasing demand for renewable energies due to the limited availability of fossil and nuclear fuels and due to growing environmental problems. Photovoltaic (PV) energy conversion has the potential to contribute significantly to the electrical energy generation in the future. Currently, the cost for photovoltaic systems is one of the main obstacles preventing production and application on a large scale. The photovoltaic research is now focused on the development of materials that will allow mass production without compromising on the conversion efficiencies. Among important selection criteria of PV material and in particular for thin films, are a suitable band gap, high absorption coefficient and reproducible deposition processes capable of large-volume and low cost production. The chalcopyrite semiconductor thin films such as Copper indium selenide and Copper indium sulphide are the materials that are being intensively investigated for lowering the cost of solar cells. Conversion efficiencies of 19 % have been reported for laboratory scale solar cell based on CuInSe2 and its alloys. The main objective of this thesis work is to optimise the growth conditions of materials suitable for the fabrication of solar cell, employing cost effective techniques. A typical heterojunction thin film solar cell consists of an absorber layer, buffer layer and transparent conducting contacts. The most appropriate techniques have been used for depositing these different layers, viz; chemical bath deposition for the window layer, flash evaporation and two-stage process for the absorber layer, and RF magnetron sputtering for the transparent conducting layer. Low cost experimental setups were fabricated for selenisation and sulphurisation experiments, and the magnetron gun for the RF sputtering was indigenously fabricated. The films thus grown were characterised using different tools. A powder X-ray diffractometer was used to analyse the crystalline nature of the films. The energy dispersive X-ray analysis (EDX) and scanning electron microscopy i (SEM) were used for evaluating the composition and morphology of the films. Optical properties were investigated using the UV-Vis-NIR spectrophotometer by recording the transmission/absorption spectra. The electrical properties were studied using the two probe and four probe electrical measurements. Nature of conductivity of the films was determined by thermoprobe and thermopower measurements. The deposition conditions and the process parameters were optimised based on these characterisations.

Studies on Chemical Bath Deposited Semiconducting Copper Selenide and Iron Sulfide Thin Films Useful For Photovoltaic Applications

Chemical bath deposition (CBD)is one of the simplest, very convient and probably the cheapest method for thin film preparation. Photovoltaic is the cleanest and the most efficient mode of conversion of energy to electrical power. Silicon is the most popular material in this field. The present study on chemical bath deposited semiconducting copper selenide and iron sulfide thin films useful for photovoltaic applications. Semiconducting thin films prepared by chemical deposition find applications as photo detectors, solar control coatings and solar cells. Copper selenide is a p-type semiconductor that finds application in photovolitics. Several heterojunction systems such as Cu2-xSe/ZnSe (for injection electro luminescence), Cu2Se/AgInSe2 and Cu2Se/Si (for photodiodes), Cu2-xSe/CdS, Cu2-xSe/CdSe, CuxSe/InP and Cu2-xSe/Si for solar cells are reported. A maximum efficiency of 8.3% was achieved for the Cu2-xSe/Si cell, various preparation techniques are used for copper selenide like vacuum evaporation, direct reaction, electrodeposition and CBD. Instability of the as-prepared films was investigation and is accounted as mainly due to deviation from stoichiometry and the formation of iron oxide impurity. A sulphur annealing chamber was designed and fabricated for this work. These samples wee also analysed using optical absorption technique, XPS (X-ray Photoelectron Spectroscopy) and XRD.(X-Ray Diffraction).The pyrite films obtained by CBD technique showed amorphous nature and the electrical studies carried out showed the films to be of high resistive nature. Future work possible in the material of iron pyrite includes sulphur annealing of the non-stochiometric iron pyrite CBD thin films in the absence of atmospheric oxygen

Effects and Modifications in In/Se and In/Sb Systems by Swift Heavy Ion Irradiation

Department of Physics, Cochin University of Science and Technology