Fabrication and integration of planar electrodes for contactless conductivity detection on polyester-toner electrophoresis microchips

In this report, we describe the microfabrication and integration of planar electrodes for contactless conductivity detection on polyester-toner (PT) electrophoresis microchips using toner masks. Planar electrodes were fabricated by three simple steps: (i) drawing and laser-printing the electrode geometry on polyester films, (ii) sputtering deposition onto substrates, and (iii) removal of toner layer by a lift-off process. The polyester film with anchored electrodes was integrated to PT electrophoresis microchannels by lamination at 120 degrees C in less than 1 min. The electrodes were designed in an antiparallel configuration with 750 mu m width and 750 gm gap between them. The best results were recorded with a frequency of 400 kHz and 10 V-PP using a sinusoidal wave. The analytical performance of the proposed microchip was evaluated by electrophoretic separation of potassium, sodium and lithium in 150 mu m wide x 6 mu m deep microchannels. Under an electric field of 250 V/cm the analytes were successfully separated in less than 90 s with efficiencies ranging from 7000 to 13 000 plates. The detection limits (S/N = 3) found for K+, Na+, and Li+ were 3.1, 4.3, and 7.2 mu mol/L, respectively. Besides the low-cost and instrumental simplicity, the integrated PT chip eliminates the problem of manual alignment and gluing of the electrodes, permitting more robustness and better reproducibility, therefore, more suitable for mass production of electrophoresis microchips.

DC Motor Speed Control via Fuzzy / Pole Placement / PI Controller

This report presents a new way of control engineering. Dc motor speed controlled by three controllers PID, pole placement and Fuzzy controller and discusses the advantages and disadvantages of each controller for different conditions under loaded and unloaded scenarios using software Matlab. The brushless series wound Dc motor is very popular in industrial application and control systems because of the high torque density, high efficiency and small size. First suitable equations are developed for DC motor. PID controller is developed and tuned in order to get faster step response. The simulation results of PID controller provide very good results and the controller is further tuned in order to decrease its overshoot error which is common in PID controllers. Further it is purposed that in industrial environment these controllers are better than others controllers as PID controllers are easy to tuned and cheap. Pole placement controller is the best example of control engineering. An addition of integrator reduced the noise disturbances in pole placement controller and this makes it a good choice for industrial applications. The fuzzy controller is introduce with a DC chopper to make the DC motor speed control smooth and almost no steady state error is observed. Another advantage is achieved in fuzzy controller that the simulations of three different controllers are compared and concluded from the results that Fuzzy controller outperforms to PID controller in terms of steady state error and smooth step response. While Pole placement controller have no comparison in terms of controls because designer can change the step response according to nature of control systems, so this controller provide wide range of control over a system. Poles location change the step response in a sense that if poles are near to origin then step response of motor is fast. Finally a GUI of these three controllers are developed which allow the user to select any controller and change its parameters according to the situation.

Caracterização de espécies brasileiras de Adesmia DC. por RAPD

Dentro do gênero Adesmia, as técnicas moleculares ainda não foram empregadas na caracterização de germoplasma e na análise da diversidade genética das espécies brasileiras que compôem o gênero. Portanto os objetivos deste trabalho foram: caracterizar, com a utilização de marcador molecular do tipo RAPD, as espécies brasileiras do gênero Adesmia DC; com base nestas informações estabelecer relações de diversidade genética entre as espécies e os acessos analisados; relacionar dados de diversidade com dados morfológicos e de reprodução.

Análise experimental da ação hepatoprotetora e antiinflamatória de Baccharis trimera (Less) DC Asteraceae

Resumo não disponível

The impact of the 2008 economic recession on three residential property type investments: a case study of five diverse zip codes in Washington DC, USA

There has been 47 recessions in the United States of America (US) since 1790. US recessions have increasingly affected economies of other countries in the world as nations become more and more interdependent on each other. The worst economic recession so far was the “Great Depression” – an economic recession that was caused by the 1929 crash of the stock market in the US. The 2008 economic recession in the US was a result of the burst of the “housing bubble” created by predatory lending. The economic recession resulted in increased unemployment (according to NBER 8.7 million jobs were lost from Feb. 2008 to Feb. 2010); decrease in GDP by 5.1%; increase in poverty level from 12.1% (2007) to 16.0% (2008) (NBER) This dissertation is an attempt to research the impact of the 2008 economic recession on different types of residential investments: a case study of five (5) diverse neighborhoods/zip codes in Washington DC, USA The main findings were that the effect of the 2008 economic depression on the different types of residential properties was dependent on the location of the property and the demographics/socio-economic factors associated with that location.

Conversores DC-DC comutados de elevado rendimento para sensores de imagem

Nesta tese de mestrado em engenharia telecomunicações e redes de energia, fez-se um estudo sobre conversores DC-DC comutados de elevado rendimento para sensores de imagem. Onde o principal objetivo é que se desenvolva, em ambiente industrial, um conversor DC-DC de alto rendimento que seja capaz de criar uma tensão inferior à sua alimentação. De salientar que o conversor foi implementado, quase na totalidade, sob a forma de circuito integrado, na tecnologia CMOS 0,35 μm. A implementação deste trabalho foi realizada por meio de um estágio na empresa de sensores de imagem Awaiba. No desenvolvimento do conversor DC-DC inicializou-se o estudo com um regulador de condensadores comutados, com uma arquitetura simples, em que se verificou, através de simulações realizadas num software específico para circuitos integrados - Design Arquitect-IC, que este regulador, apesar de estabilizar a tensão de saída na pretendida, não apresentava alto rendimento, ficando pelos 62%. Na sequência do estudo, na tentativa de melhorar as características do regulador de condensadores comutados, desenvolveu-se um conversor DC-DC com um filtro passa baixo na saída. Verificou-se, através de simulação que este conversor apresentava um rendimento de 92%, onde a sua tensão de alimentação é de 3,3 V e consegue regular na sua saída uma tensão variável entre 1,4 V e 2,2 V, suportando uma corrente máxima de 200 mA. É de referir que o conversor desenvolvido apresenta um tempo de resposta de 20 μs quando ocorre um consumo de corrente com variação em escalão. Sendo um conversor adequado para alimentar sensores de imagem e com elevado rendimento.

Germinação e armazenamento de sementes de COCA (Erythroxylum ligustrinum DC. - Erythroxylaceae)

O objetivo deste trabalho foi avaliar o efeito da temperatura sobre a germinação e o armazenamento de sementes de Erythroxylum ligustrinum DC. As sementes foram colocadas germinar caixas de plásticas sobre duas folhas de papel, umedecidas com Nistatina 0, 2%, mantidas em germinadores nas temperaturas constantes de 5, 10, 15, 20, 25, 30, 35, 40 e 45ºC e com fotoperíodo de 12 horas. Para o armazenamento, as sementes foram colocadas em sacos de papel, mantidos à temperatura ambiente e em geladeira. em seguida, mensalmente, foi avaliada a germinação das sementes. A temperatura mínima, a faixa de temperatura ideal e a temperatura máxima para germinação de sementes de coca estão entre 10 e 15ºC, 25 e 30ºC e 40 e 45ºC, respectivamente. O armazenamento de sementes coca por longo período é inviável em embalagens de papel na geladeira (10ºC ± 2) e em temperatura ambiente (27ºC ± 5).

Anti-leishmanial effects of purified compounds from aerial parts of Baccharis uncinella C. DC. (Asteraceae)

Species of Baccharis exhibit antibiotic, antiseptic, wound-healing, and anti-protozoal properties, and have been used in the traditional medicine of South America for the treatment of several diseases. In the present work, the fractionation of EtOH extract from aerial parts of Baccharis uncinella indicated that the isolated compounds caffeic acid and pectolinaringenin showed inhibitory activity against Leishmania (L.) amazonensis and Leishmania (V.) braziliensis promastigotes, respectively. Moreover, amastigote forms of both species were highly sensible to the fraction composed by oleanolic + ursolic acids and pectolinaringenin. Caffeic acid also inhibited amastigote forms of L. (L.) amazonensis, but this effect was weak in L. (V.) braziliensis amastigotes. The treatment of infected macrophages with these compounds did not alter the levels of nitrates, indicating a direct effect of the compounds on amastigote stages. The results presented herein suggest that the active components from B. uncinella can be important to the design of new drugs against American tegumentar leishmaniases.

Viabilidade de sementes de acerola (Malpighia emarginata DC): avaliação da vitalidade dos tecidos

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Compostos orgânicos como substratos na formação de mudas de ipê-amarelo (Tabebuia Chrysotricha (Mart. Ex. Dc.) Standl) irrigadas com água residuária

A necessidade de estudar a utilização dos resíduos de podas de árvores é de grande importância ambiental para solucionar os problemas de resíduos sólidos existentes nas áreas urbanas junto com os resíduos de lixos domésticos. O estudo destes materiais foi avaliado com o desenvolvimento de mudas de ipê-amarelo (Tabebuia Chrysotricha (Mart. Ex. Dc.) sandl) em diferentes misturas de substratos e tipos de água para irrigação. O experimento foi instalado no Departamento de Engenharia Rural da Faculdade de Ciências Agrárias e Veterinárias - UNESP, Câmpus de Jaboticabal. Foram realizados dois experimentos, avaliados juntamente com delineamento experimental em blocos casualizados, de oito substratos, duas qualidades de águas e quatro repetições, totalizando 64 parcelas. Cada parcela foi composta por 30 plantas (cinco linhas de seis plantas), sendo consideradas como úteis as três linhas de quatro plantas centrais da parcela. Foram testados oito substratos, resultantes da combinação de substrato comercial, composto de lixo e composto de poda de árvores com dois tipos de água de irrigação (água potável e residuária) e quatro repetições. Para acompanhar o desenvolvimento das mudas de ipê-amarelo, foram avaliados a altura da parte aérea das plantas (H) e o diâmetro do colmo (D). As características foram avaliadas aos 21; 42; 63 e 84 dias após a emergência. da análise dos resultados, possibilitou-se concluir que os substratos estudados promoveram diferenças significativas para a altura média das plantas e o diâmetro de colmo, em todos os períodos de avaliação. Os substratos 4 e 5 e a água residuária apresentaram os melhores resultados no desenvolvimento das mudas de ipê-amarelo.

Inhibition of the myotoxic activity of Bothrops jararacussu venom and its two major myotoxins, BthTX-I and BthTX-II, by the aqueous extract of Tabernaemontana catharinensis A. DC. (Apocynaceae)

Partial neutralization of the myotoxic effect of Bothrops jararacussu venom (BV) and two of its myotoxins [bothropstoxin-I (BthTX-I), catalytically inactive, and II (BthTX-II), showing low PLA(2) activity], by the lyophilized aqueous extract of Tabernaemontana catharinensis (AE), was studied in rat isolated soleus muscle preparations (in vitro) and through i.m. injection in the gastrocnemius muscle (in vivo) by determination of creatine kinase (CK) activity and histopathological analysis. Incubation of soleus muscle for 1 h with BV or toxins (20 mug/ml) plus AE (400 mug/ml) added immediately after BV, BthTX-I or BthTX-II reduced CK levels by 53%, 37% and 56%, respectively. The myonecrotic effects of BV (20 mug/ml) upon soleus muscle was reduced 24%, 35% and 36% when AE (400 mug/ml) was added 1 h after BV and CK was evaluated 30 min, 1 and 2 h later, respectively. For BthTX-I these values were 46%, 48% and 47%, while for BthTX-II no inhibitory effect was detected. Histological analysis of soleus muscle after incubation with AE (400 mug/ml, I h) did not reveal any change in muscle fibers, but severe necrosis induced by -BV or toxins (20 mug/ml) was clearly in evidence, and decreased significantly when soleus muscle was protected by AE. This protection was also observed when AE was administered 1 h after BV or BthTX-I, but not after BthTX-II. AE did not inhibit the catalytic PLA(2), activity of BthTX-II or BV and did not change the PAGE pattern of BV, BthTX-I or BthTX-II. In vivo assays were performed in 100-g rats and maximal CK release was attained at a dose of 100 mug of BV, 3 h after injection. AE was not effective when injected 20 s after BV or toxins. However, injecting BV or toxins (100 mug), which were pre-incubated with AE (2 mg) caused an inhibition of 57%, 59% and 51%, respectively, with zero time pre-incubation, but was less effective with I h pre-incubation. This plant represents a potential source of promising myotoxin inhibitors. (C) 2004 Elsevier GmbH. All rights reserved.

Influência de genótipos de couve (Brassica oleracea L. var. acephala DC.) na biologia de Plutella xylostella (L., 1758) (Lepidoptera: Plutellidae)

Objetivou-se, com este trabalho, avaliar a influência de alguns genótipos de couve (Brassica oleracea L. var. acephala DC.) no desenvolvimento de Plutella xylostella (L., 1758) (Lepidoptera: Plutellidae). Os genótipos avaliados foram: Manteiga de Ribeirão Pires I-2620, Roxa I-919, Manteiga de São José, Manteiga de Monte Alegre, Pires 2 de Campinas, Couve Comum, Couve de Arthur Nogueira 2, Couve de Arthur Nogueira 1. Lagartas recém-eclodidas foram mantida em discos foliares de 8 cm de diâmetro para cada genótipo. Foram analisados os seguintes parâmetros: duração e viabilidade das fases larval e pupal, longevidade e fecundidade de adultos, utilizando análises paramétricas e de agrupamentos para interpretação dos dados. Observou-se um prolongamento em dias no ciclo de P. xylostella, aumento no peso de pupa e maiores valores de viabilidade e fecundidade, durante a segunda geração. O genótipo Couve de Arthur Nogueira 2 foi menos favorável ao desenvolvimento de P. xylostella nas duas gerações, e Couve Comum demonstrou maior influência negativa ao inseto na segunda geração. Manteiga de Ribeirão Pires I-2620 foi o mais suscetível nas duas gerações, agrupando com este na segunda geração Pires 2 de Campinas e Manteiga de São José.

Electrical conductivity of soybean seeds after storage in several environments

Membrane integrity, as measured by electrical conductivity (EC), is suggested as an indicator of seed vigor in soybean [Glycine max (L.) Merrill] seeds. This study evaluated the effect of storage time and temperature on EC of six soybean seed lots (two lots each of high, medium and low vigor). All seed lots were adjusted to 120 g kg(-1) seed moisture, sealed in aluminum foil packets and placed in storage at 10 and 20 degreesC or stored unsealed in multi-wall paper bags in warehouse (WH) conditions at Lexington, KY, USA for 486 days. Four of the six seed lots were also stored unsealed at 10 degreesC. All seed lots were sampled at 3-month intervals and evaluated for seed moisture (SMC), standard germination (SG) and vigor [accelerated aging (AA) and EC]. After 91 and 204 days in storage, samples initially stored at 20 degreesC and WH were moved to 10 degreesC and sampled at the same intervals. Seed moisture content for unsealed samples equilibrated at 107 g kg(-1) (+/-9 g kg(-1)) in both the WH and 10 degreesC environments. No change in SG occurred for seeds stored sealed (120 g kg(-1)) at 10 degreesC, except for the low vigor seed lots which declined significantly at the last sample date. The AA germination declined significantly for all, seed lots stored sealed at 10 degreesC, however the EC did not change during the same storage period. Seeds stored sealed at 20 degreesC and unsealed in the WH showed rapid declines in AA and SG and significant increases in EC. When these seeds were moved to 10 degreesC, however, the AA continued to decline while the EC remained at the same level (no significant change) for the remainder of the seed storage period. Thus whilst the AA declined in all environments, the EC only increased at higher temperatures (20 degreesC, WH) but showed little change during storage at 10 degreesC. Thus, precautions must be taken if using EC to measure soybean seed vigor following storage at 10 degreesC.

Electrical conductivity of the seed soaking solution and soybean seedling emergence

Vigor of soybean [Glycine max (L.) Merrill] seeds can be evaluated by measuring the electrical conductivity (EC) of the seed soaking solution, which has shown a satisfactory relationship with field seedling emergence, but has not had aproper definition of range yet. This work studies the relationship between EC and soybean seedling emergence both in the field and laboratory conditions, using twenty two seed lots. Seed water content, standard germination and vigor (EC, accelerated aging and cold tests) were evaluated under laboratory conditions using -0.03; -0.20; -0.40 and -0.60 MPa matric potentials, and field seedling emergence was also observed. There was direct relationship between EC and field seedling emergence (FE). Under laboratory conditions, a decreasing relationship was found between EC and FE as water content in the substrate decreased, Relationships between these two parameters were also found when -0.03; -0.20 and -0.40 MPa matric potentials were used. EC tests can be used successfully to evaluate soybean seed vigor and identify lots with higher or lower field emergence potential.