Investigação da condutividade hidráulica dos solos de uma área de aterro de resíduos sólidos urbanos por meio de ensaios de campo e laboratório

A contaminant plume due to leachate infiltration was found in the solid waste landfill from Bauru, SP. The soil hydraulic conductivity (K) is an important parameter to understand the moving of this plume. This paper intends to show representative K values for the soils that occur in the vicinity of this landfill determined by field and laboratory tests. There are four soil types in the area: colluvium, alluvium, sandstone residual soil and the sandstone. Laboratory tests were performed using constant and variable head in rigid and flexible wall permeameters. Slug tests and hydraulic conductivity tests with the Guelph permeameter were also carried out in situ in the area. Representative K values of 3.7x10-7 m/s for the saturated zone and 2.4x10-8 m/s for the unsaturated zone were determined for the residual soil. A K value of 5.3x10-5 m/s was obtained for the colluvium soil. A great variation of K with depth was observed for the alluvium and the assumed average values for the saturated zone were 7.9x10-7 m/s and 1.1x10-4 m/s for the unsaturated surficial layer. An average K value of 3.3x10-8 m/s was determined in laboratory for the sandstone and it was assumed representative for this material.

Construção e validação de um túnel de vento para ensaios de estimativa da deriva em pulverizações agrícolas

The aim of this study was to build and validate a low cost reduced-scale wind tunnel for drift evaluation on pesticide application technology. The work was carried out at the NEMPA - Núcleo de Ensaio de Máquinas e Pneus Agroflorestais (NEMPA), FCA/UNESP, Departamento de Engenharia Rural, Botucatu/SP, Brazil. The wind tunnel main characteristics were an open circuit and a closed working section with a fan blowing air into the tunnel. Screens were fitted downstream after the fan in order to stabilize the air flow on the working section. The tunnel was built with 3.0 mm eucalyptus hardboard, with a total length of 4.8 m and a squared section of 0.56 m. The air flow was provided by a 180 W axial fan. The system was adjusted and calibrated to provide a laminar and stable flow at 2.0 m s-1. Validation studies were carried out by using a Teejet XR 8003 flat fan nozzle at 200 kPa (medium droplets) to apply a spray solutions containing water plus a food dye (Blue FDC) at 0,6% m v-1 mixed with two adjuvants: a polymer based anti drift formulation at 0,06% m v-1 and a sodium lauryl ether sulfate based surfactant at 0,2% v v-1. After a 10-second application the drift was collected on nylon strips transversally fixed along the tunnel at different distances from the nozzle and different high from the bottom part of the tunnel. Drift deposits were evaluated by spectrophotometry. The wind tunnel had low levels of turbulence and high repeatability of the data, which means that the flow was uniform and able to be used for carrying out measures to estimate drift. The validation results showed that the tunnel was effective to enable comparative drift measurements on the spray solution used in this work making possible the evaluation of drift risk potential under those spray technologies. The use of an adjuvant based on a polymer reduced the amount of drift from the nozzle compared to the surfactant.

Deposição e danos mecânicos em sementes de sorgo utilizando um mecanismo dosador de fluxo contínuo em ensaio de bancada

This study aimed to evaluate the behavior of the deposition and mechanical damage in seeds using a continuous flow metering system under different slope and speed. Part of the study was conducted at Agricultural Research Foundation Agricultural - (FAPA), where seeds that are deposited by a metering system were collected, and the quality analysis verifying the percentage of mechanical damage were conducted at the Faculty of Agricultural Sciences, UNESP, city of Botucatu– SP. The mechanism deposition was subjected to three different speed conditions (4,7, and 10 km.h-1) and three differents working slopes, ( 3%, 8%, and 16%). The results were submitted to Tukey test (p ≤ 0.05), and an analysis of variance with F test at 5% significance level was performed. The results showed an interaction between the factor slope and speed of work, increasing the metering mechanism speed, results in a reduction of the seed deposition at a 3% slope but a working speed of 10 km h-1did not reduce the rate of seed deposition until the slope reaches 16%. Both the slope factor and the working speed caused at least 3.9 and 4.2% more damage to the seeds, respectively.

Efeito da modificação atmosférica em goiabas var. Paluma na redução de danos mecânicos em pós-colheita

In the postharvest management, the fruits can be exposed to injuries that depreciated the quality and the shelf life. Thus, it was evaluated the modified atmosphere effects on guavas var. Paluma subjected to different mechanical damages. Once harvested, the fruits were selected, sanitized and submitted to the treatments T1 (control) - without injuries or packaging in bags of low density polyethylene (LDPE); T2 - without injuries + LDPE bags; T3 - damage by fall of 1 m + LDPE bags; T4 - damage by compression of 9 N + LDPE bags; T5 - damage by fall of 1 m + damage by compression of 9 N + LDPE bags and T6 - damage by fall of 1 m + damage by compression of 9 N without LDPE bags. The treatments were kept in cold storage at 10 ± 1 o C and 94 ± 2% de R.H. The analysis of CO2/ethylene production, enzymatic activity, total and soluble pectins, pulp firmness, titratable acidity (TA), soluble solids (SS), reducing sugars and ascorbic acid were performed every 10 days of refrigeration, and an additional day outside cold storage (22 ± 1o C and 75 ± 3% R.H.) for 30 days. Guavas packed in LDPE bags, not subject to mechanical damage, presented the best quality standards. The fruits suffered only one kind of damage, when packaged, presented satisfactory pattern compared to the fruits without package and not exposed to any mechanical damages. Applying the two kinds of damages, the LDPE packaging was not adequate to decrease the metabolic rate of these fruits, making them unfit for marketing.

Intervenções para aumentar adesão às precauçôes padrão e/ou baseadas nas vias de transmissão de micro-organismos aos cuidados do paciente: revisão sistemática de ensaios clínicos randomizados e não randomizados, séries temporais e estudos controlados antes e depois

Pós-graduação em Enfermagem - FMB

Controle das propriedades dinâmicas de sistemas mecânicos através da utilização de molas inteligentes

Pós-graduação em Engenharia Mecânica - FEIS

Análise de integridade física de barragens de terra a partir da integração do método geofísico da eletrorresistividade com ensaios geotécnicos

Pós-graduação em Geociências e Meio Ambiente - IGCE

Colunas de Winogradsky com águas contaminadas por petróleo e derivados monitoradas por ensaios ecotoxicológicos

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Estudo da resistência à corrosão de ligas Ni-Cr-Mo-Ta E Ni-Cr-Mo-W em solução NaF 0,08 mol/L, pH 4,7 para aplicações odontológicas

A large number of metal alloys are used in Dentistry for the manufacture of fixed and removable dentures. In the oral cavity, these structures are exposed to a chemically aggressive medium, like saliva and mechanical efforts, like mastication. In addition, acidic solutions containing fluoride ions are also frequently used in dental treatments to prevent dental plates and decays development. In this context, it was considered important to investigate the influence that a fourth element could exert when added to the ternary alloy Ni-Cr-Mo, largely used in Brazil. Therefore, electrochemical tests were done to evaluate the resistance to corrosion of quaternary alloy 65Ni-25Cr-5Mo-5Ta and 65Ni-25Cr-5Mo-5W in NaF solution 0,08mol / L, pH = 4.7. For greater understanding the microstructure and morphology of alloys were studied, through metallographic analysis, using optics microscopy and electron microscopy scanning. For the electrochemical tests were applied techniques traditionally used in corrosion researches, such as: potential measures in open circuit (OCP) and cyclic polarization (CP). It was found that both quaternary alloys showed very similar results. Comparing these quaternary alloys with the ternary 65Ni-25Cr-10Mo, it was found that the quaternary alloys exhibit greater resistance to corrosion, in other words, less passivation current density than the ternary alloy, showing that it is advantageous to add a fourth element in the alloy

Concepção detalhada de uma bancada para simular esforços mecânicos em colunas de perfuração

In this work we study the construction of a test rig made to simulate the Mechanical efforts in wich a drillstring is submitted. The model is based on the rig built at IDS, Germany. There are some fault liabilities while doing the project of the axis. Therefore it's important to analyze and take knowledge of this efforts in order to predict failures like rupture or fatigue collapse. The main objective of this theis is to show the operating principle of the test rig and it's construction. The accomplished study allow us to predict the drillstring behavior and from the economic point of view that is very important because failures results in equipments maintenance that requires time and money causing prejudice to the company. Using SolidWorks, a simulation software, the thesis approaches all the mechanical parts required for it's construction as well as it's working principle. Acquisition sensors like strain gauges, accelerometer, and torque transductor were also used in this model. The objective of this thesis is to create a simulation model to be eventually at FEG(UNESP). During the development of the study, it was possible to learn more about the drilling process and the mechanical efforts in which the drill pipe is submitted. The accomplished contributed with knowledge for the student in the drilling process area. Also during the development of the study it was possible to have contact with different areas of engineering but the study is specifically directed to the construction of the test rig. Therefore the main theme of this thesis is to show the operating principle of the test rig and it's construction

Projeto de adaptação do sistema de injeção do túnel transônico para ensaios em bocais de foguete

In this work, the project of a new experimental facility to be installed at the Aerodynamics Division of the Institute of Aeronautics and Space is presented. This new facility will provide means to perform experimental campaigns to analyze the flow behavior at different rocket nozzle concepts using cold gas that will be obtained from a modification of the Pilot Transonic Wind Tunnel air system. The new installation will enable less expensive experiments in a more secure environment, since the cold gas experimental procedures do not demand fuel storage and burn and security procedures are much less severe. Furthermore, experiments can be carried with different types of sensors, commonly used in wind tunnel tests. Also, the optical access is facilitated enabling the use of optical techniques for the characterization of flow properties inside the nozzles, such as pressure and temperature sensitive painting. The full project design and the operation conditions will be showed, as also some technical considerations about the flor behavior in the facility

Análise de integridade física de barragens de terra a partir da integração do método geofísico da eletrorresistividade com ensaios geotécnicos

Pós-graduação em Geociências e Meio Ambiente - IGCE

Colunas de Winogradsky com águas contaminadas por petróleo e derivados monitoradas por ensaios ecotoxicológicos

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Estudo da resistência à corrosão de ligas Ni-Cr-Mo-Ta E Ni-Cr-Mo-W em solução NaF 0,08 mol/L, pH 4,7 para aplicações odontológicas

A large number of metal alloys are used in Dentistry for the manufacture of fixed and removable dentures. In the oral cavity, these structures are exposed to a chemically aggressive medium, like saliva and mechanical efforts, like mastication. In addition, acidic solutions containing fluoride ions are also frequently used in dental treatments to prevent dental plates and decays development. In this context, it was considered important to investigate the influence that a fourth element could exert when added to the ternary alloy Ni-Cr-Mo, largely used in Brazil. Therefore, electrochemical tests were done to evaluate the resistance to corrosion of quaternary alloy 65Ni-25Cr-5Mo-5Ta and 65Ni-25Cr-5Mo-5W in NaF solution 0,08mol / L, pH = 4.7. For greater understanding the microstructure and morphology of alloys were studied, through metallographic analysis, using optics microscopy and electron microscopy scanning. For the electrochemical tests were applied techniques traditionally used in corrosion researches, such as: potential measures in open circuit (OCP) and cyclic polarization (CP). It was found that both quaternary alloys showed very similar results. Comparing these quaternary alloys with the ternary 65Ni-25Cr-10Mo, it was found that the quaternary alloys exhibit greater resistance to corrosion, in other words, less passivation current density than the ternary alloy, showing that it is advantageous to add a fourth element in the alloy

Concepção detalhada de uma bancada para simular esforços mecânicos em colunas de perfuração

In this work we study the construction of a test rig made to simulate the Mechanical efforts in wich a drillstring is submitted. The model is based on the rig built at IDS, Germany. There are some fault liabilities while doing the project of the axis. Therefore it's important to analyze and take knowledge of this efforts in order to predict failures like rupture or fatigue collapse. The main objective of this theis is to show the operating principle of the test rig and it's construction. The accomplished study allow us to predict the drillstring behavior and from the economic point of view that is very important because failures results in equipments maintenance that requires time and money causing prejudice to the company. Using SolidWorks, a simulation software, the thesis approaches all the mechanical parts required for it's construction as well as it's working principle. Acquisition sensors like strain gauges, accelerometer, and torque transductor were also used in this model. The objective of this thesis is to create a simulation model to be eventually at FEG(UNESP). During the development of the study, it was possible to learn more about the drilling process and the mechanical efforts in which the drill pipe is submitted. The accomplished contributed with knowledge for the student in the drilling process area. Also during the development of the study it was possible to have contact with different areas of engineering but the study is specifically directed to the construction of the test rig. Therefore the main theme of this thesis is to show the operating principle of the test rig and it's construction