Design methodologies of microwawe integrated circuits for satellite telecommunications

The running innovation processes of the microwave transistor technologies, used in the implementation of microwave circuits, have to be supported by the study and development of proper design methodologies which, depending on the applications, will fully exploit the technology potentialities. After the choice of the technology to be used in the particular application, the circuit designer has few degrees of freedom when carrying out his design; in the most cases, due to the technological constrains, all the foundries develop and provide customized processes optimized for a specific performance such as power, low-noise, linearity, broadband etc. For these reasons circuit design is always a “compromise”, an investigation for the best solution to reach a trade off between the desired performances. This approach becomes crucial in the design of microwave systems to be used in satellite applications; the tight space constraints impose to reach the best performances under proper electrical and thermal de-rated conditions, respect to the maximum ratings provided by the used technology, in order to ensure adequate levels of reliability. In particular this work is about one of the most critical components in the front-end of a satellite antenna, the High Power Amplifier (HPA). The HPA is the main power dissipation source and so the element which mostly engrave on space, weight and cost of telecommunication apparatus; it is clear from the above reasons that design strategies addressing optimization of power density, efficiency and reliability are of major concern. Many transactions and publications demonstrate different methods for the design of power amplifiers, highlighting the availability to obtain very good levels of output power, efficiency and gain. Starting from existing knowledge, the target of the research activities summarized in this dissertation was to develop a design methodology capable optimize power amplifier performances complying all the constraints imposed by the space applications, tacking into account the thermal behaviour in the same manner of the power and the efficiency. After a reminder of the existing theories about the power amplifier design, in the first section of this work, the effectiveness of the methodology based on the accurate control of the dynamic Load Line and her shaping will be described, explaining all steps in the design of two different kinds of high power amplifiers. Considering the trade-off between the main performances and reliability issues as the target of the design activity, we will demonstrate that the expected results could be obtained working on the characteristics of the Load Line at the intrinsic terminals of the selected active device. The methodology proposed in this first part is based on the assumption that designer has the availability of an accurate electrical model of the device; the variety of publications about this argument demonstrates that it is so difficult to carry out a CAD model capable to taking into account all the non-ideal phenomena which occur when the amplifier operates at such high frequency and power levels. For that, especially for the emerging technology of Gallium Nitride (GaN), in the second section a new approach for power amplifier design will be described, basing on the experimental characterization of the intrinsic Load Line by means of a low frequency high power measurements bench. Thanks to the possibility to develop my Ph.D. in an academic spin-off, MEC – Microwave Electronics for Communications, the results of this activity has been applied to important research programs requested by space agencies, with the aim support the technological transfer from universities to industrial world and to promote a science-based entrepreneurship. For these reasons the proposed design methodology will be explained basing on many experimental results.

Analisi dei parametri vegetazionali e dei caratteri funzionali di specie guida come strumenti di studio di comunità prative

Lo studio condotto si propone l’approfondimento delle conoscenze sui processi di evoluzione spontanea di comunità vegetali erbacee di origine secondaria in cinque siti all’interno di un’area protetta del Parco di Monte Sole (Bologna, Italia), dove, come molte aree rurali marginali in Italia e in Europa, la cessazione o riduzione delle tradizionali pratiche gestionali negli ultimi cinquant’anni, ha determinato lo sviluppo di fitocenosi di ridotto valore floristico e produttivo. Tali siti si trovano in due aree distinte all’interno del parco, denominate Zannini e Stanzano, selezionate in quanto rappresentative di situazioni di comunità del Mesobrometo. Due siti appartenenti alla prima area e uno appartenente alla seconda, sono gestiti con sfalcio annuale, i rimanenti non hanno nessun tipo di gestione. Lo stato delle comunità erbacee di tali siti è stato valutato secondo più punti di vista. E’ stata fatta una caratterizzazione vegetazionale dei siti, mediante rilievo lineare secondo la metodologia Daget-Poissonet, permettendo una prima valutazione relativa al numero di specie presenti e alla loro abbondanza all’interno della comunità vegetale, determinando i Contributi Specifici delle famiglie principali e delle specie dominanti (B. pinnatum, B. erectus e D. glomerata). La produttività è stata calcolata utilizzando un indice di qualità foraggera, il Valore Pastorale, e con la determinazione della produzione di Fitomassa totale, Fitomassa fotosintetizzante e Necromassa. A questo proposito sono state trovate correlazioni negative tra la presenza di Graminacee, in particolare di B. pinnatum, e i Contributi Specifici delle altre specie, soprattutto a causa dello spesso strato di fitomassa e necromassa prodotto dallo stesso B. pinnatum che impedisce meccanicamente l’insediamento e la crescita di altre piante. E’ stata inoltre approfonditamente sviluppata un terza caratterizzazione, che si propone di quantificare la diversità funzionale dei siti medesimi, interpretando le risposte della vegetazione a fattori globali di cambiamento, sia abiotici che biotici, per cogliere gli effetti delle variazioni ambientali in atto sulla comunità, e più in generale, sull’intero ecosistema. In particolare, nello studio condotto, sono stati proposti alcuni caratteri funzionali, cosiddetti functional traits, scelti perché correlati all’acquisizione e alla conservazione delle risorse, e quindi al trade-off dei nutrienti all’interno della pianta, ossia: Superficie Fogliare Specifica, SLA, Tenore di Sostanza Secca, LDMC, Concentrazione di Azoto Fogliare, LNC, Contenuto in Fibra, LFC, separato nelle componenti di Emicellulosa, Cellulosa, Lignina e Ceneri. Questi caratteri sono stati misurati in relazione a tre specie dominanti: B. pinnatum, B. erectus e D. glomerata. Si tratta di specie comunemente presenti nelle praterie semi-mesofile dell’Appennino Settentrionale, ma caratterizzate da differenti proprietà ecologiche e adattative: B. pinnatum e B. erectus sono considerati competitori stress-toleranti, tipicamente di ambienti poveri di risorse, mentre D. glomerata, è una specie più mesofila, caratteristica di ambienti produttivi. Attraverso l’analisi dei traits in riferimento alle diverse strategie di queste specie, sono stati descritti specifici adattamenti alle variazioni delle condizioni ambientali, ed in particolare in risposta al periodo di stress durante l’estate dovuto a deficit idrico e in risposta alla diversa modalità di gestione dei siti, ossia alla pratica o meno dello sfalcio annuale. Tra i caratteri funzionali esaminati, è stato identificato LDMC come il migliore per descrivere le specie, in quanto più facilmente misurabile, meno variabile, e direttamente correlato con altri traits come SLA e le componenti della fibra. E’ stato quindi proposto il calcolo di un indice globale per caratterizzare i siti in esame, che tenesse conto di tutti questi aspetti, riunendo insieme sia i parametri di tipo vegetativo e produttivo, che i parametri funzionali. Tale indice ha permesso di disporre i siti lungo un gradiente e di cogliere differenti risposte in relazione a variazioni stagionali tra primavera o autunno e in relazione al tipo di gestione, valutando le posizioni occupate dai siti stessi e la modalità dei loro eventuali spostamenti lungo questo gradiente. Al fine di chiarire se le variazioni dei traits rilevate fossero dovute ad adattamento fenotipico dei singoli individui alle condizioni ambientali, o piuttosto fossero dovute a differenziazione genotipica tra popolazioni cresciute in siti diversi, è stato proposto un esperimento in condizioni controllate. All’interno di un’area naturale in UK, le Chiltern Hills, sono stati selezionati cinque siti, caratterizzati da diverse età di abbandono: Bradenham Road MaiColtivato e Small Dean MaiColtivato, di cui non si conosce storia di coltivazione, caratterizzati rispettivamente da vegetazione arborea e arbustiva prevalente, Butterfly Bank 1970, non più coltivato dal 1970, oggi prateria seminaturale occasionalmente pascolata, Park Wood 2001, non più coltivato dal 2001, oggi prateria seminaturale mantenuta con sfalcio annuale, e infine Manor Farm Coltivato, attualmente arato e coltivato. L’esperimento è stato condotto facendo crescere i semi delle tre specie più comuni, B. sylvaticum, D. glomerata e H. lanatus provenienti dai primi quattro siti, e semi delle stesse specie acquistati commercialmente, nei cinque differenti tipi di suolo dei medesimi siti. Sono stati misurati quattro caratteri funzionali: Massa Radicale Secca (DRM), Massa Epigea Secca (DBM), Superficie Fogliare Secca (SLA) e Tenore di Sostanza Secca (LDMC). I risultati ottenuti hanno evidenziato che ci sono significative differenze tra le popolazioni di una stessa specie ma con diversa provenienza, e tra individui appartenenti alla stessa popolazione se fatti crescere in suoli diversi. Tuttavia, queste differenze, sembrano essere dovute ad adattamenti locali legati alla presenza di nutrienti, in particolare N e P, nel suolo piuttosto che a sostanziali variazioni genotipiche tra popolazioni. Anche per questi siti è stato costruito un gradiente sulla base dei quattro caratteri funzionali analizzati. La disposizione dei siti lungo il gradiente ha evidenziato tre gruppi distinti: i siti più giovani, Park Wood 2001 e Manor Farm Coltivato, nettamente separati da Butterfly Bank 1970, e seguiti infine da Small Dean MaiColtivato e Bradenham Road MaiColtivato. L’applicazione di un indice così proposto potrebbe rivelarsi un utile strumento per descrivere ed indagare lo stato della prateria e dei processi evolutivi in atto, al fine di meglio comprendere e dominare tali dinamiche per proporre sistemi di gestione che ne consentano la conservazione anche in assenza delle tradizionali cure colturali.

Algorithms for on-line image registration from multiple views

Images of a scene, static or dynamic, are generally acquired at different epochs from different viewpoints. They potentially gather information about the whole scene and its relative motion with respect to the acquisition device. Data from different (in the spatial or temporal domain) visual sources can be fused together to provide a unique consistent representation of the whole scene, even recovering the third dimension, permitting a more complete understanding of the scene content. Moreover, the pose of the acquisition device can be achieved by estimating the relative motion parameters linking different views, thus providing localization information for automatic guidance purposes. Image registration is based on the use of pattern recognition techniques to match among corresponding parts of different views of the acquired scene. Depending on hypotheses or prior information about the sensor model, the motion model and/or the scene model, this information can be used to estimate global or local geometrical mapping functions between different images or different parts of them. These mapping functions contain relative motion parameters between the scene and the sensor(s) and can be used to integrate accordingly informations coming from the different sources to build a wider or even augmented representation of the scene. Accordingly, for their scene reconstruction and pose estimation capabilities, nowadays image registration techniques from multiple views are increasingly stirring up the interest of the scientific and industrial community. Depending on the applicative domain, accuracy, robustness, and computational payload of the algorithms represent important issues to be addressed and generally a trade-off among them has to be reached. Moreover, on-line performance is desirable in order to guarantee the direct interaction of the vision device with human actors or control systems. This thesis follows a general research approach to cope with these issues, almost independently from the scene content, under the constraint of rigid motions. This approach has been motivated by the portability to very different domains as a very desirable property to achieve. A general image registration approach suitable for on-line applications has been devised and assessed through two challenging case studies in different applicative domains. The first case study regards scene reconstruction through on-line mosaicing of optical microscopy cell images acquired with non automated equipment, while moving manually the microscope holder. By registering the images the field of view of the microscope can be widened, preserving the resolution while reconstructing the whole cell culture and permitting the microscopist to interactively explore the cell culture. In the second case study, the registration of terrestrial satellite images acquired by a camera integral with the satellite is utilized to estimate its three-dimensional orientation from visual data, for automatic guidance purposes. Critical aspects of these applications are emphasized and the choices adopted are motivated accordingly. Results are discussed in view of promising future developments.

A hybrid technology for parallel recording of single ion channels

Hybrid technologies, thanks to the convergence of integrated microelectronic devices and new class of microfluidic structures could open new perspectives to the way how nanoscale events are discovered, monitored and controlled. The key point of this thesis is to evaluate the impact of such an approach into applications of ion-channel High Throughput Screening (HTS)platforms. This approach offers promising opportunities for the development of new classes of sensitive, reliable and cheap sensors. There are numerous advantages of embedding microelectronic readout structures strictly coupled to sensing elements. On the one hand the signal-to-noise-ratio is increased as a result of scaling. On the other, the readout miniaturization allows organization of sensors into arrays, increasing the capability of the platform in terms of number of acquired data, as required in the HTS approach, to improve sensing accuracy and reliabiity. However, accurate interface design is required to establish efficient communication between ionic-based and electronic-based signals. The work made in this thesis will show a first example of a complete parallel readout system with single ion channel resolution, using a compact and scalable hybrid architecture suitable to be interfaced to large array of sensors, ensuring simultaneous signal recording and smart control of the signal-to-noise ratio and bandwidth trade off. More specifically, an array of microfluidic polymer structures, hosting artificial lipid bilayers blocks where single ion channel pores are embededed, is coupled with an array of ultra-low noise current amplifiers for signal amplification and data processing. As demonstrating working example, the platform was used to acquire ultra small currents derived by single non-covalent molecular binding between alpha-hemolysin pores and beta-cyclodextrin molecules in artificial lipid membranes.

Studio ed ottimizzazione di caricabatterie in configurazione flyback

Questa tesi tratta dell'ottimizzazione dei componenti di potenza di un convertitore flyback al fine di massimizzare l'efficienza di un caricabatteria per batterie al piombo. Le perdite vengono studiate all'interno di uno spazio di progetto che individua due variabili libere (rapporto spire e indice di ondulazione della corrente). Diverse mappe con le stime di dissipazione derivante da tutti i contributi, permettono l'individuazione del punto ottimo di progetto e consentono la corretta valutazione dei trade-off. Il risultato dell'analisi ha portato al progetto di un dimostratore in cui si è potuto verificare la correttezza del valore di efficienza predetta, in questo modo migliorando le performance di un prodotto esistente.

Variabilità spaziale dei parametri di modelli afflussi-deflussi

L’invarianza spaziale dei parametri di un modello afflussi-deflussi può rivelarsi una soluzione pratica e valida nel caso si voglia stimare la disponibilità di risorsa idrica di un’area. La simulazione idrologica è infatti uno strumento molto adottato ma presenta alcune criticità legate soprattutto alla necessità di calibrare i parametri del modello. Se si opta per l’applicazione di modelli spazialmente distribuiti, utili perché in grado di rendere conto della variabilità spaziale dei fenomeni che concorrono alla formazione di deflusso, il problema è solitamente legato all’alto numero di parametri in gioco. Assumendo che alcuni di questi siano omogenei nello spazio, dunque presentino lo stesso valore sui diversi bacini, è possibile ridurre il numero complessivo dei parametri che necessitano della calibrazione. Si verifica su base statistica questa assunzione, ricorrendo alla stima dell’incertezza parametrica valutata per mezzo di un algoritmo MCMC. Si nota che le distribuzioni dei parametri risultano in diversa misura compatibili sui bacini considerati. Quando poi l’obiettivo è la stima della disponibilità di risorsa idrica di bacini non strumentati, l’ipotesi di invarianza dei parametri assume ancora più importanza; solitamente infatti si affronta questo problema ricorrendo a lunghe analisi di regionalizzazione dei parametri. In questa sede invece si propone una procedura di cross-calibrazione che viene realizzata adottando le informazioni provenienti dai bacini strumentati più simili al sito di interesse. Si vuole raggiungere cioè un giusto compromesso tra lo svantaggio derivante dall’assumere i parametri del modello costanti sui bacini strumentati e il beneficio legato all’introduzione, passo dopo passo, di nuove e importanti informazioni derivanti dai bacini strumentati coinvolti nell’analisi. I risultati dimostrano l’utilità della metodologia proposta; si vede infatti che, in fase di validazione sul bacino considerato non strumentato, è possibile raggiungere un buona concordanza tra le serie di portata simulate e osservate.

Ultra-low power WSNs: distributed signal processing and dynamic resource management

This thesis presents several data processing and compression techniques capable of addressing the strict requirements of wireless sensor networks. After introducing a general overview of sensor networks, the energy problem is introduced, dividing the different energy reduction approaches according to the different subsystem they try to optimize. To manage the complexity brought by these techniques, a quick overview of the most common middlewares for WSNs is given, describing in detail SPINE2, a framework for data processing in the node environment. The focus is then shifted on the in-network aggregation techniques, used to reduce data sent by the network nodes trying to prolong the network lifetime as long as possible. Among the several techniques, the most promising approach is the Compressive Sensing (CS). To investigate this technique, a practical implementation of the algorithm is compared against a simpler aggregation scheme, deriving a mixed algorithm able to successfully reduce the power consumption. The analysis moves from compression implemented on single nodes to CS for signal ensembles, trying to exploit the correlations among sensors and nodes to improve compression and reconstruction quality. The two main techniques for signal ensembles, Distributed CS (DCS) and Kronecker CS (KCS), are introduced and compared against a common set of data gathered by real deployments. The best trade-off between reconstruction quality and power consumption is then investigated. The usage of CS is also addressed when the signal of interest is sampled at a Sub-Nyquist rate, evaluating the reconstruction performance. Finally the group sparsity CS (GS-CS) is compared to another well-known technique for reconstruction of signals from an highly sub-sampled version. These two frameworks are compared again against a real data-set and an insightful analysis of the trade-off between reconstruction quality and lifetime is given.

Postkommunistische Wirtschaftsreformen und politische Institutionen : eine Analyse der wirtschaftspolitischen Handlungsfähigkeit junger Demokratien auf Basis der Vetospieler-Theorie

Diese Arbeit analysiert den Zusammenhang zwischen politischen Institutionen und wirtschaftlichen Reformen. Die verbreitete Meinung nimmt an, dass ein hohes Maß an politischer Kontrolle und Beschränkungen, etwa durch ein föderales System oder eine zweite Parlamentskammer, die Reformfähigkeit eines Landes negativ beeinflusst. Grundlage dieser Annahme sind die Schlussfolgerungen aus der Vetospieler-Theorie von George Tsebelis. Anhand des Reformverlaufs postkommunistischer Staaten zeigt diese Arbeit jedoch, dass der Zusammenhang zwischen politischer Beschränkung und Reformen nicht linear, sondern quadratisch ist. Ein Mittelweg zwischen einer frei waltenden Exekutive und einem System restriktiver checks and balances garantiert damit die größtmöglichen Fortschritte bei wirtschaftlichen Reformen von der Planwirtschaft zur Marktwirtschaft.

Essays on the Empirical Analysis of Economic and Political Development in Sub-Saharan Africa

In Sub-Saharan Africa, non-democratic events, like civil wars and coup d'etat, destroy economic development. This study investigates both domestic and spatial effects on the likelihood of civil wars and coup d'etat. To civil wars, an increase of income growth is one of common research conclusions to stop wars. This study adds a concern on ethnic fractionalization. IV-2SLS is applied to overcome causality problem. The findings document that income growth is significant to reduce number and degree of violence in high ethnic fractionalized countries, otherwise they are trade-off. Income growth reduces amount of wars, but increases its violent level, in the countries with few large ethnic groups. Promoting growth should consider ethnic composition. This study also investigates the clustering and contagion of civil wars using spatial panel data models. Onset, incidence and end of civil conflicts spread across the network of neighboring countries while peace, the end of conflicts, diffuse only with the nearest neighbor. There is an evidence of indirect links from neighboring income growth, without too much inequality, to reduce the likelihood of civil wars. To coup d'etat, this study revisits its diffusion for both all types of coups and only successful ones. The results find an existence of both domestic and spatial determinants in different periods. Domestic income growth plays major role to reduce the likelihood of coup before cold war ends, while spatial effects do negative afterward. Results on probability to succeed coup are similar. After cold war ends, international organisations seriously promote democracy with pressure against coup d'etat, and it seems to be effective. In sum, this study indicates the role of domestic ethnic fractionalization and the spread of neighboring effects to the likelihood of non-democratic events in a country. Policy implementation should concern these factors.

Multidimensional item response theory models with general and specific latent traits for ordinal data

The aim of the thesis is to propose a Bayesian estimation through Markov chain Monte Carlo of multidimensional item response theory models for graded responses with complex structures and correlated traits. In particular, this work focuses on the multiunidimensional and the additive underlying latent structures, considering that the first one is widely used and represents a classical approach in multidimensional item response analysis, while the second one is able to reflect the complexity of real interactions between items and respondents. A simulation study is conducted to evaluate the parameter recovery for the proposed models under different conditions (sample size, test and subtest length, number of response categories, and correlation structure). The results show that the parameter recovery is particularly sensitive to the sample size, due to the model complexity and the high number of parameters to be estimated. For a sufficiently large sample size the parameters of the multiunidimensional and additive graded response models are well reproduced. The results are also affected by the trade-off between the number of items constituting the test and the number of item categories. An application of the proposed models on response data collected to investigate Romagna and San Marino residents' perceptions and attitudes towards the tourism industry is also presented.

Approccio multidisciplinare per le valutazioni ambientali: Problematiche e sinergie in un uso combinato delle metodologie life cycle assessment (lca) e risk assessment (ra)

In questo lavoro di tesi si è elaborato un quadro di riferimento per l’utilizzo combinato di due metodologie di valutazione di impatti LCA e RA, per tecnologie emergenti. L’originalità dello studio sta nell’aver proposto e anche applicato il quadro di riferimento ad un caso studio, in particolare ad una tecnologia innovativa di refrigerazione, basata su nanofluidi (NF), sviluppata da partner del progetto Europeo Nanohex che hanno collaborato all’elaborazione degli studi soprattutto per quanto riguarda l’inventario dei dati necessari. La complessità dello studio è da ritrovare tanto nella difficile integrazione di due metodologie nate per scopi differenti e strutturate per assolvere a quegli scopi, quanto nel settore di applicazione che seppur in forte espansione ha delle forti lacune di informazioni circa processi di produzione e comportamento delle sostanze. L’applicazione è stata effettuata sulla produzione di nanofluido (NF) di allumina secondo due vie produttive (single-stage e two-stage) per valutare e confrontare gli impatti per la salute umana e l’ambiente. Occorre specificare che il LCA è stato quantitativo ma non ha considerato gli impatti dei NM nelle categorie di tossicità. Per quanto concerne il RA è stato sviluppato uno studio di tipo qualitativo, a causa della problematica di carenza di parametri tossicologici e di esposizione su citata avente come focus la categoria dei lavoratori, pertanto è stata fatta l’assunzione che i rilasci in ambiente durante la fase di produzione sono trascurabili. Per il RA qualitativo è stato utilizzato un SW specifico, lo Stoffenmanger-Nano che rende possibile la prioritizzazione dei rischi associati ad inalazione in ambiente di lavoro. Il quadro di riferimento prevede una procedura articolata in quattro fasi: DEFINIZIONE SISTEMA TECNOLOGICO, RACCOLTA DATI, VALUTAZIONE DEL RISCHIO E QUANTIFICAZIONE DEGLI IMPATTI, INTERPRETAZIONE.

Silicon Photonics Integrated Circuits for Flexible Optical Systems

This dissertation deals with the design and the characterization of novel reconfigurable silicon-on-insulator (SOI) devices to filter and route optical signals on-chip. Design is carried out through circuit simulations based on basic circuit elements (Building Blocks, BBs) in order to prove the feasibility of an approach allowing to move the design of Photonic Integrated Circuits (PICs) toward the system level. CMOS compatibility and large integration scale make SOI one of the most promising material to realize PICs. The concepts of generic foundry and BB based circuit simulations for the design are emerging as a solution to reduce the costs and increase the circuit complexity. To validate the BB based approach, the development of some of the most important BBs is performed first. A novel tunable coupler is also presented and it is demonstrated to be a valuable alternative to the known solutions. Two novel multi-element PICs are then analysed: a narrow linewidth single mode resonator and a passband filter with widely tunable bandwidth. Extensive circuit simulations are carried out to determine their performance, taking into account fabrication tolerances. The first PIC is based on two Grating Assisted Couplers in a ring resonator (RR) configuration. It is shown that a trade-off between performance, resonance bandwidth and device footprint has to be performed. The device could be employed to realize reconfigurable add-drop de/multiplexers. Sensitivity with respect to fabrication tolerances and spurious effects is however observed. The second PIC is based on an unbalanced Mach-Zehnder interferometer loaded with two RRs. Overall good performance and robustness to fabrication tolerances and nonlinear effects have confirmed its applicability for the realization of flexible optical systems. Simulated and measured devices behaviour is shown to be in agreement thus demonstrating the viability of a BB based approach to the design of complex PICs.

Decomposition Methods and Network Design Problems

Decomposition based approaches are recalled from primal and dual point of view. The possibility of building partially disaggregated reduced master problems is investigated. This extends the idea of aggregated-versus-disaggregated formulation to a gradual choice of alternative level of aggregation. Partial aggregation is applied to the linear multicommodity minimum cost flow problem. The possibility of having only partially aggregated bundles opens a wide range of alternatives with different trade-offs between the number of iterations and the required computation for solving it. This trade-off is explored for several sets of instances and the results are compared with the ones obtained by directly solving the natural node-arc formulation. An iterative solution process to the route assignment problem is proposed, based on the well-known Frank Wolfe algorithm. In order to provide a first feasible solution to the Frank Wolfe algorithm, a linear multicommodity min-cost flow problem is solved to optimality by using the decomposition techniques mentioned above. Solutions of this problem are useful for network orientation and design, especially in relation with public transportation systems as the Personal Rapid Transit. A single-commodity robust network design problem is addressed. In this, an undirected graph with edge costs is given together with a discrete set of balance matrices, representing different supply/demand scenarios. The goal is to determine the minimum cost installation of capacities on the edges such that the flow exchange is feasible for every scenario. A set of new instances that are computationally hard for the natural flow formulation are solved by means of a new heuristic algorithm. Finally, an efficient decomposition-based heuristic approach for a large scale stochastic unit commitment problem is presented. The addressed real-world stochastic problem employs at its core a deterministic unit commitment planning model developed by the California Independent System Operator (ISO).

The Road to Poverty Reduction: Corporate Governance and Female Participation in MFIs

1.Microfinance Industry – Context of Analysis. This paper is an introduction to the microfinance industry. It serves as a context of analysis, for the empirical settings and basis for building the theoretical argument for the thesis. 2.Women in Microfinance Institutions: The Road to Poverty Reduction and Gender Equality? One of the unique aspects of microfinance institutions is their focus on outreach, i.e. their ability to reach the poor. This paper explores whether the presence of women in microfinance institutions is associated with improved outreach. Building on prior research that shows that women tend to improve financial performance and social responsibility, we examine an original dataset of 226 microfinance institutions. The empirical results suggest that the presence of a female CEO, female managers and female loan officers is directly related to improved outreach, while the presence of women board members is not. 3. Women in Microfinance Institutions: Is There a Trade-Off Between Outreach and Sustainability? Abstract This paper’s contribution to the understanding of microfinance is two-fold. First, while it has been shown that female CEOs in MFIs increase financial performance, it will be argued that female managers, female loan officers and female board members will do the same. Secondly, having previously shown that having a female presence in management in MFIs improves social performance the outreach, it will be argued that having females in the MFIs’ management will not lead to a trade-off between outreach and sustainability. These findings are based on an original data set of 226 MFIs. Statistical analysis demonstrates that a weak relationship between female managers and female loan officers vis-à-vis financial performance, but female board members do not. The trade-off between outreach and sustainability can be avoided with the appointment of females to the MFIs’ management positions, but the same cannot be concluded for female board members.

The reconstruction of skeletal movement: the soft tissue artefact issue

In 3D human movement analysis performed using stereophotogrammetric systems and skin markers, bone pose can only be estimated in an indirect fashion. During a movement, soft tissue deformations make the markers move with respect to the underlying bone generating soft tissue artefact (STA). STA has devastating effects on bone pose estimation and its compensation remains an open question. The aim of this PhD thesis was to contribute to the solution of this crucial issue. Modelling STA using measurable trial-specific variables is a fundamental prerequisite for its removal from marker trajectories. Two STA model architectures are proposed. Initially, a thigh marker-level artefact model is presented. STA was modelled as a linear combination of joint angles involved in the movement. This model was calibrated using ex-vivo and in-vivo STA invasive measures. The considerable number of model parameters led to defining STA approximations. Three definitions were proposed to represent STA as a series of modes: individual marker displacements, marker-cluster geometrical transformations (MCGT), and skin envelope shape variations. Modes were selected using two criteria: one based on modal energy and another on the selection of modes chosen a priori. The MCGT allows to select either rigid or non-rigid STA components. It was also empirically demonstrated that only the rigid component affects joint kinematics, regardless of the non-rigid amplitude. Therefore, a model of thigh and shank STA rigid component at cluster-level was then defined. An acceptable trade-off between STA compensation effectiveness and number of parameters can be obtained, improving joint kinematics accuracy. The obtained results lead to two main potential applications: the proposed models can generate realistic STAs for simulation purposes to compare different skeletal kinematics estimators; and, more importantly, focusing only on the STA rigid component, the model attains a satisfactory STA reconstruction with less parameters, facilitating its incorporation in an pose estimator.