Manipulation of chromosomes in fish: review of various techniques and their implications in aquaculture

Human ingenuity has made it possible to advent the chromosome manipulation techniques to produce individuals with differing genomic status in a number of fish using various causal agents such as physical shocks (temperature or hydrostatic pressure), chemical (endomitotics) and anesthetic treatments either to suppress the second meiotic division shortly after fertilization of eggs or to prevent the first mitotic division shortly prior to mitotic cleavage formation. This results in the induction of polyploidy (triploidy and tetraploidy), gynogenesis (both meiotic and mitotic leading to clonal lines) and androgenesis in fish population. The rationale for the induction of such ploidy in fish has been its potential for generating sterile individuals, rapidly inbred lines and masculinized fish, which could be of benefit to fish farming and aquaculture. In this paper, these are critically reviewed and the implication of recently developed chromosome manipulation techniques to various fin fishes is discussed.

TECHNIQUES FOR PRODUCING DEFECT-FREE SOI BY DUAL ELECTRON BEAM HEATING OF DEPOSITED POLYSILICON.

Advances in the dual electron-beam recrystallization technique arising from the fast scanning of a line beam parallel to the edges of narrow seeding windows are described. The resultant recrystallized layers are essentially defect-free, have good surface flatness, and cover large areas.

EXPERIMENTAL TECHNIQUES IN COMBUSTION USE OF IN-CYLINDER IONISATION FOR THE INVESTIGATION AND CONTROL OF SPARK IGNITION ENGINES.

Ions generated during combustion have been used in three ways to give qualitative combustion information. Langmuir type probes have been inserted into the combustion chamber opposite the spark plug location. The centre electrode of the sparking plug itself has been used to produce an ionisation signal from the slightly ionised gases remaining after the flame front has departed. The spark discharge at ignition time has been used as an anemometer.

ANALYSIS OF A PROBLEM INVOLVING RADIAL CONSOLIDATION.

An analytical solution is presented for the vertical consolidation of a cylindrical annulus of clay with horizontal drainage occurring to concentric internal and external drainage boundaries. Numerical results are given for various ratios of internal and external radii and it is shown that solutions for conventional one-dimensional consolidation, and for consolidation of a cylindrical block of clay with drainage only to the outer cylindrical boundary form extremes to the analysis presented here. An application of the solution to the estimation of horizontal permeability of clay is briefly described.

SUB-BAND CODING TECHNIQUES FOR ROBUST 4. 8 TO 8 kb/s SPEECH CODERS.

This paper describes a speech coding technique that has been developed in order to provide a method of digitising speech at bit rates in the range 4. 8 to 8 kb/s, that is insensitive to the effects of acoustic background noise and bit errors on the digital link. The main aim has been to develop a coding scheme which provides speech quality and robustness against noise and errors that is similar to a 16000 b/s continuously variable slope delta (CVSD) coder, but which operates at half its data rate or less. A desirable aim was to keep the complexity of the coding scheme within the scope of what could reasonably be handled by current signal processing chips or by a single custom integrated circuit. Applications areas include mobile radio and small Satcomms terminals.

Comparison of different scheduling techniques for H-infinity controllers

Several approaches to designing schedule H-infinity control systems are compared. These include a controller switching approach and also parameter scheduling of an observer representation of the controller. They are illustrated by application to a Generic VSTOI. Aircraft Model (GVAM) supplied by The Royal Aerospace Establishment (RAE) at Bedford. The switched design has been tested on the simulator at RAE Bedford. The linear H-infinity designs make use of a loop-shaping followed by robust stabilisation to additive perturbations of a normalised coprime factorisation of the shaped plans. The different scheduling approaches are compared with respect to achieved robust stability levels. performance and complexity of implementation.

Experimental study of tip clearance flow in a radial inflow turbine

This paper describes an experimental investigation of tip clearance flow in a radial inflow turbine. Flow visualization and static pressure measurements were performed. These were combined with hot-wire traverses into the tip gap. The experimental data indicates that the tip clearance flow in a radial turbine can be divided into three regions. The first region is located at the rotor inlet, where the influence of relative casing motion dominates the flow over the tip. The second region is located towards midchord, where the effect of relative casing motion is weakened. Finally a third region exists in the exducer, where the effect of relative casing motion becomes small and the leakage flow resembles the tip flow behaviour in an axial turbine. Integration of the velocity profiles showed that there is little tip leakage in the first part of the rotor because of the effect of scraping. It was found that the bulk of tip leakage flow in a radial turbine passes through the exducer. The mass flow rate, measured at four chordwise positions, was compared with a standard axial turbine tip leakage model. The result revealed the need for a model suited to radial turbines. The hot-wire measurements also indicated a higher tip gap loss in the exducer of the radial turbine. This explains why the stage efficiency of a radial inflow turbine is more affected by increasing the radial clearance than by increasing the axial clearance.

Techniques for the transport and maintenance of scleractinian coral

Several small scleractinian coral colonies were collected from a remote reef and transferred [to] the Louisiana Universities Marine Center (LUMCON) for in vitro reproductive and larval studies. The species used here were Porites astreoides and Diploria strigosa. Colony size was ~20 cm in diameter. Colonies were brought to the surface by liftbag and stored in modified ice coolers. They were transported from Freeport, TX to Cocodrie, LA by truck for nearly 15 hours where field conditions were simulated in waiting aquaria. This document describes the techniques and equipment that were used, how to outfit such aquaria, proper handling techniques for coral colonies, and several eventualities that the mariculturist should be prepared for in undertaking this endeavor. It will hopefully prevent many mistakes from being made.

Application of domain decomposition and transmission line modelling techniques to 2D, time-domain, finite element problems

In this paper a recently published finite element method, which combines domain decomposition with a novel technique for solving nonlinear magnetostatic finite element problems is described. It is then shown how the method can be extended to, and optimised for, the solution of time-domain problems. © 1999 IEEE.

The use of C-V techniques to investigate instability mechanisms in M-I-S structures

In the field of flat panel displays, the current leading technology is the Active Matrix liquid Crystal Display; this uses a-Si:H based thin film transistors (TFTs) as the switching element in each pixel. However, under gate bias a-Si:H TFTs suffer from instability, as is evidenced by a shift in the gate threshold voltage. The shift in the gate threshold voltage is generally measured from the gate transfer characteristics, after subjecting the TFT to prolonged gate bias. However, a major drawback of this measurement method is that it cannot distinguish whether the shift is caused by the change in the midgap states in the a-Si:H channel or by charge trapping in the gate insulator. In view of this, we have developed a capacitance-voltage (C-V) method to measure the shift in threshold voltage. We employ Metal-Insulator-Semiconductor (MIS) structures to investigate the threshold voltage shift as they are simpler to fabricate than TFTs. We have investigated a large of number Metal/a-Si:H/Si3N4/Si+n structures using our C-V technique. From, the C-V data for the MIS structures, we have found that the relationship between the thermal energy and threshold voltage shift is similar to that reported by Wehrspohn et. al in a-Si:H TFTs (J Appl. Phys, 144, 87, 2000). The a-Si:H and Si3N4 layers were grown using the radio-frequency plasma-enhanced chemical vapour deposition technique.