Temperature and thiol-induced desensitization of a Ca2+-sensitive cyclic-3',5'-nucleotide phosphodiesterase from sheep lung

Ca2+-sensitivity of sheep lung cyclic-3',5'-nucleotide phosphodiesterase is provided by endogenous tightly bound calmodulin. The calcium sensitivity of a highly purified enzyme was desensitized by increasing the assay temperature. It could also be desensitized to Ca2+-activation by thiols such as dithiothreitol. The thiol-induced desensitization could be partially reversed by dialysis and almost completely reversed by dilution. The results presented in this paper indicate that thiols are possibly involved in the interaction of calmodulin with cyclic-3',5'-nucleotide phosphodiesterase. This is the first report on temperature and thiol-induced desensitization of Ca2+-sensitivity of a cyclic-3',5'-nucleotide phosphodiesterase.

The structure of 3[beta],20[alpha]-bis(dimethylamino)pregn-5-en-18-ol

Abstract. C25H44N20 , M r= 388.6, orthorhombic, P21212 I, a = 6.185 (2), b = 18.123 (2), c = 20.852 (2) A, U= 2337.2 A 3, Z = 4, D x = 1.104 Mg m -a, 2(Cu Ka) = 1.5418 A,/~ = 0.47 mm -~, F(000) = 864, T= 293 K. Final R - 0.038 for 1791 reflections with I >_ 3a(I). Rings A and C are in chair conformation. Ring B is in an 8fl,9a-half-chair conformation. Ring D adopts a conformation in between 13fl,14a-half-chair and 13t-envelope. There is a quasitrans fusion of rings A and B, whilst ring systems B/C and C/D are trans fused about the bonds C(8)-C(9)and C(13)-C(14).

Strain-rate sensitivity and microstructural evolution in a Mg-Al-Zn alloy

Strain rate sensitivity measurements are used to identify twinning and changes in deformation mechanisms in a Mg AZ31 alloy over a wide range of temperatures and grain sizes. At low temperatures, there is significant twinning at low strains with strain-rate insensitivity; at large strains, strain rate sensitivity is noted, corresponding to deformation by multiple slip. At high temperatures, there is very little twinning and this leads to a significant strain rate sensitivity from the early stages of deformation. (C) 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Effect of phenyl and phenolic acids on mevalonate-5-Phosphate decarboxylase if the brain

Phenyl and phenolic acids are known to inhibit metabolism of mevalonate in rat brain. The site of inhibition has been found to be mevalonate-5-pyrophosphate decarboxylase. Phenolic acids also inhibited mevalonate-5-phosphate kinase on preincubation. The kinetics showed that p-coumaric acid and isoferulic acid were competing with substrates, mevalonate-5-phosphate or mevalonate-5-pyre phosphate, whereas others showed an uncompetitive type of inhibition. Chlorophenoxyisobutyrate, a hypocholesterolaemic drug, had no effect on these enzymes. An improved method for the synthesis of mevalonate-5-phosphate and mevalonate-5-pyrophosphate, labeled at carbon-1, is described.

Mean square displacements of hydrogen interstitial and its neighbours in the intermetallic compound Fe0.5Ti0.5

A Green's function technique is used in the scattering matrix formalism to compute the mean square displacement of hydrogen and deuterium interstitials in the intermetallic compound Fe0.5Ti0.5 for low hydrogen/deuterium concentration. The mean square amplitudes of the metal atoms surrounding the interstitial are found to be smaller than those for the host crystal. This anomalous effect is due to the stiffening of the lattice by the dissolved hydrogen or deuterium at low concentration. This type of effect is experimentally observed in the case of NbHx at low hydrogen concentration.

Numerical simulation of solidification of liquid aluminum alloy flowing on cooling slope

Preparation of semisolid slurry using a cooling slope is increasingly becoming popular, primarily because of the simplicity in design and ease control of the process. In this process, liquid alloy is poured down an inclined surface which is cooled from underneath. The cooling enables partial solidification and the incline provides the necessary shear for producing semisolid slurry. However, the final microstructure of the ingot depends on several process parameters such as cooling rate, incline angle of the cooling slope, length of the slope and initial melt superheat. In this work, a CFD model using volume of fluid (VOF) method for simulating flow along the cooling slope was presented. Equations for conservation of mass, momentum, energy and species were solved to predict hydrodynamic and thermal behavior, in addition to predicting solid fraction distribution and macrosegregation. Solidification was modeled using an enthalpy approach and a volume averaged technique for the different phases. The mushy region was modeled as a multi-layered porous medium consisting of fixed columnar dendrites and mobile equiaxed/fragmented grains. The alloy chosen for the study was aluminum alloy A356, for which adequate experimental data were available in the literature. The effects of two key process parameters, namely the slope angle and the pouring temperature, on temperature distribution, velocity distribution and macrosegregation were also studied.

Induction reheating of A356.2 aluminum alloy and thixocasting as automobile component

The development work for producing an automobile component by thixocasting using A356.2 alloy was introduced. As the first step, the alloy was electromagnetically stirred and solidified to produce a billet with non-dendritic microstructure. The microstructure depended on several process parameters such as stirring intensity, stirring frequency, cooling rate, and melt initial superheat. Through a series of computational studies and controlled experiments, a set of process parameters were identified to produce the best microstructures. Reheating of a billet with non-dendritic microstructure to a semisolid temperature was the next step for thixo-casting of the components. The reheating process was characterized for various reheating cycles using a vertical-type reheating machine. The induction heating cycle was optimized to obtain a near-uniform temperature distribution in radial as well as axial direction of the billet, and the heating was continued until the liquid fraction reached about 50%. These parameters were determined with the help of a computational fluid dynamics (CFD) model of die filling and solidification of the semisolid alloy. The heated billets were subsequently thixo-cast into automobile components using a real-time controlled die casting machine. The results show that the castings are near net shape, free from porosity, good surface finish and have superior mechanical properties compared to those produced by conventional die casting processes using the same alloy.

1-(3,5-Diethyl-1H-pyrazol-1-yl)-3-phenylisoquinoline

In the title molecule, C22H21N3, the isoquinoline ring is almost planar maximum deviation = 0.046 (1) A] and makes dihedral angles of 52.01 (4) and 14.61 (4)degrees with the pyrazole and phenyl rings, respectively. The phenyl ring and the pyrazole ring are twisted by 44.20 (6)degrees with respect to each other. The terminal C atoms of both of the ethyl groups attached to the pyrazole ring are disordered over two sites with occupancy ratios of 0.164 (7):0.836 (7) and 0.447 (16):0.553 (16). A weak intramolecular C-H...N contact may influence the molecular conformation. The crystal structure is stabilized by C-H...pi contacts involving the phenyl and pyrazole rings, and by pi-pi stacking interactions involving the pyridine and benzene rings centroid-centroid distance = 3.5972 (10) A].