Determination of dissolved oxygen in water with leukoberbelin-blue I. A quick Winkler method. [Translation from: Z.analyt.Chem. 262 97-99, 1972.]

The reaction of Mn(II) with water-dissolved oxygen, to a higher manganese hydroxide in an alkaline medium, as with the longstanding classic Winkler method, is the first step in the method described here. The assumption for faultless results by the conventional and modified Winkler method is clean water, which contains no organic substances by Mn(III) or Mn(IV). In many cases, however, eg. in river and lake-water tests, it can be seen with the naked eye that after some time the originally brown-coloured precipitate of manganese hydroxide becomes more and more colourless. Oxygen content was analysed in the water samples and evaluated by raising the amount of the leuko-base and giving the corresponding dilution of the colouring matter solution formed still higher oxygen contents can be measured.

Determination of the activity of nitrifying bacteria in surface waters by a modified BOD-test. [Translation from: Zentbl.Bakt.Parasitkde 156(1) 414-421, 1972. ]

A modified method of the Biochemical oxygen demand (BOD)test was applied in order to find out the seasonal changing activity of the nitrifying bacteria in surface waters. Samples were taken from the River Elbe near Teufelsbrueck.

For the determination of iron (II) and total iron with 2,2'-dipyridyl in mineral waters. Reduction of iron (III) with ascorbic acid [Translation from: Zeitschrift fur Analytische Chemie 209 340-341, 1965]

The determination of bi- and trivalent iron in proximity, in mineral waters has gained in significance, on biological and technical grounds. This short paper describes the procedure of the determination of bivalent iron and total iron in a water sample.

Application of algal bioassays in the determination of eutrophic power of waste water (”Conclusions” only) [Translation from: 1g.Sanita pubbl. 31 257-267, 1975]

The best evidence for establishing the level of eutrophy of a water-body is its algal production which makes it possible to identify the type and the intensity of the eutrophication according to the kind and number of algal species present: when the number of algae exceeds half a million per litre then one speaks o an ”algal bloom”. The scope of the present research aims to verify if the alga Selenastrum capricornutum can be used as a test alga under our culture conditions and to determine the eutrophic level of the secondary effluent of a modern plant for the treatment of domestic discharge and to investigate the eventual ”limiting factors”. Finally this paper aims to study the effect on the secondary effluent of tertiary treatment carried out artificially in the laboratory.

Toxicidade e bioacumulação de cobre em micro-organismos fotoautotróficos

Microalgas e cianobactérias têm sido amplamente recomendadas para biomonitoração de metais pesados e outros poluentes, sendo considerados indicadores sensíveis às alterações ambientais e utilizados como organismos testes na regulamentação dos níveis de metal. Estes micro-organismos fotossintetizantes são produtores primários da base da cadeia alimentar aquática e são os primeiros a serem afetados pela poluição por metais pesados. O cobre é um metal normalmente considerado como nutriente essencial para a vida aquática mas pode ser tóxico para algumas espécies. Portanto, neste estudo foram avaliados o efeito tóxico e a bioacumulação de cobre (II) em quatro espécies de micro-organismos fotoautotróficos componentes do fitoplâncton dulcícola, duas cianobactérias filamentosas (Anabaena sp. e Oscillatoria sp) e duas microalgas da classe das clorofíceas (Monorraphidium sp. e Scenedesmus sp.). O meio de cultivo utilizado nos ensaios foi o ASM-1 com e sem a presença de cobre (0,6 mg/L a 12 mg Cu2+/L) onde, o efeito tóxico do metal foi monitorado por contagem celular para as microalgas e por peso seco para as cianobactérias. A bioacumulação do metal foi avaliada da mesma forma para todos os micro-organismos, através de coletas de amostras no decorrer do experimento e determinação da concentração de cobre em solução por espectrometria de absorção atômica com chama. Os resultados obtidos mostram que o efeito tóxico do metal é diretamente proporcional à concentração inicial para os micro-organismos estudados, mas que o cobre (II) foi mais tóxico para as cianobactérias que para as microalgas verdes. A bioacumulação teve uma relação direta com o efeito tóxico do metal sobre os micro-organismos. Os resultados obtidos permitem sugerir que cobre (II) tem efeito negativo no fitoplâncton, inibindo o crescimento e alterando parâmetros metabólicos como a fotossíntese. A bioacumulação do metal pode comprometer os níveis tróficos da cadeia alimentar, afetando seu transporte para seres superiores

Radioautographic method of determination of number of bacteria in water-bodies [Translation from: Informatsionnyi Byulleten Biologiya Vnutrennikh Vod No.26, 65-67, 1975]

The radioautographic method of determination of the number of autotrophic microorganisms was initially suggested for counting methane-oxidizing bacteria. With the help of this method colonies of hydrogen-oxidizing bacteria are differentiated even more clearly from heterotrophic. Under laboratory conditions it was shown that colonies grown on membrane filters from a pure culture of thionic bacteria on a nutrient medium with radio- active carbonate, give better prints on film. This method was tested by the authors for determining the number of these bacteria in the meromictic Lake Vae de San Juan during the expedition to Cuba in the summer of 1973. The study showed that that the thionic bacteria are found throughout the pelagial. It proved that the thionic bacteria can be well considered in water-bodies by the radioautographic method.

A colorimetric determination of hydrocyanic acid

The object of this investigation is to devise a rapid, fairly accurate, colorimetric analysis for HCN to be used in field work for determining instantaneous concentrations of the gas under fumigating canvas. A large amount of money is expended yearly by the citrus industry of this state in attempting to control and to eradicate the scale pests. Although fumigation with HCN has been practiced tor many years, the progress made has been anything but satisfactory. The greater portion of the work has always been carried on by contractors, who in a large number of cases have been very unscrupulous. The materials and labor are very expensive and the growers have been satisfied to adhere to beaten paths and hope for the best results on scale kill with the least attendant foliage injury. One familiar with fumigating, either from the grower's or the operator's viewpoint, knows that very widely varying results are obtained, even under what are apparently identical condition. Even after discounting for the dishonesty of some operators and the prejudices of the grower, there is still a large variance between desired or expected results and those actually obtained.

Optical two-dimensional SW-banyan network: Optical implementation, routing control, and determination of permissible permutations

A 2-D SW-banyan network is introduced by properly folding the 1-D SW-banyan network, and its corresponding optical setup is proposed by means of polarizing beamsplitters and 2-D phase spatial light modulators. Then, based on the characteristics and the proposed optical setup, the control for the routing path between any source-destination pair is given, and the method to determine whether a given permutation is permissible or not is discussed. Because the proposed optical setup consists of only optical polarization elements, it is compact in structure, its corresponding energy loss and crosstalk are low, and its corresponding available number of channels is high. (C) 1996 Society of Photo-Optical Instrumentation Engineers.

Highly sensitive wave-front sensor with a non-zero-order phase plate

We propose a novel highly sensitive wave front detection method for a quick check of a flat wave front by taking advantage of a non-zero-order pi phase plate that yields a non-zero-order diffraction pattern. When a light beam with a flat wave front illuminates a phase plate, the zero-order intensity is zero. When there is a slight distortion of the wave front, the zero-order intensity increases. The ratio of first-order intensity to that of zero-order intensity is used as the criterion with which to judge whether the wave front under test is flat, eliminating the influence of background light. Experimental results demonstrate that this method is efficient, robust, and cost-effective and should be highly interesting for a quick check of a flat wave front of a large-aperture laser beam and adaptive optical systems. (c) 2005 Optical Society of America.

I. A study of the dynamics of triplet excitons in molecular crystals. II. An investigation of delayed light emission from Chlorella pyrenoidosa

I. PREAMBLE AND SCOPE

Brief introductory remarks, together with a definition of the scope of the material discussed in the thesis, are given.

II. A STUDY OF THE DYNAMICS OF TRIPLET EXCITONS IN MOLECULAR CRYSTALS

Phosphorescence spectra of pure crystalline naphthalene at room temperature and at 77˚ K are presented. The lifetime of the lowest triplet ³B_1u state of the crystal is determined from measurements of the time-dependence of the phosphorescence decay after termination of the excitation light. The fact that this lifetime is considerably shorter in the pure crystal at room temperature than in isotopic mixed crystals at 4.2˚ K is discussed, with special importance being attached to the mobility of triplet excitons in the pure crystal.

Excitation spectra of the delayed fluorescence and phosphorescence from crystalline naphthalene and anthracene are also presented. The equation governing the time- and spatial-dependence of the triplet exciton concentration in the crystal is discussed, along with several approximate equations obtained from the general equation under certain simplifying assumptions. The influence of triplet exciton diffusion on the observed excitation spectra and the possibility of using the latter to investigate the former is also considered. Calculations of the delayed fluorescence and phosphorescence excitation spectra of crystalline naphthalene are described.

A search for absorption of additional light quanta by triplet excitons in naphthalene and anthracene crystals failed to produce any evidence for the phenomenon. This apparent absence of triplet-triplet absorption in pure crystals is attributed to a low steady-state triplet concentration, due to processes like triplet-triplet annihilation, resulting in an absorption too weak to be detected with the apparatus used in the experiments. A comparison of triplet-triplet absorption by naphthalene in a glass at 77˚ K with that by naphthalene-h₈ in naphthalene-d₈ at 4.2˚ K is given. A broad absorption in the isotopic mixed crystal triplet-triplet spectrum has been tentatively interpreted in terms of coupling between the guest ³B_1u state and the conduction band and charge-transfer states of the host crystal.

III. AN INVESTIGATION OF DELAYED LIGHT EMISSION FROM Chlorella Pyrenoidosa

An apparatus capable of measuring emission lifetimes in the range 5 X 10^-9 sec to 6 X 10^-3 sec is described in detail. A cw argon ion laser beam, interrupted periodically by means of an electro-optic shutter, serves as the excitation source. Rapid sampling techniques coupled with signal averaging and digital data acquisition comprise the sensitive detection and readout portion of the apparatus. The capabilities of the equipment are adequately demonstrated by the results of a determination of the fluorescence lifetime of 5, 6, 11, 12-tetraphenyl-naphthacene in benzene solution at room temperature. Details of numerical methods used in the final data reduction are also described.

The results of preliminary measurements of delayed light emission from Chlorella Pyrenoidosa in the range 10^-3 sec to 1 sec are presented. Effects on the emission of an inhibitor and of variations in the excitation light intensity have been investigated. Kinetic analysis of the emission decay curves obtained under these various experimental conditions indicate that in the millisecond-to-second time interval the decay is adequately described by the sum of two first-order decay processes. The values of the time constants of these processes appear to be sensitive both to added inhibitor and to excitation light intensity.

Studies of temperature sensitive mutants of polyoma virus

Polyoma virus can undergo two different types of interactions with susceptible cells; one type of interaction leads to the production of new infectious virus and eventual cell death while the other leads to a neoplastically transformed cell which is able to continue to divide under conditions that inhibit the multiplication of uninfected normal cells. In order to study the viral genes involved in both of these virus-cell interactions the isolation of temperature sensitive mutants of polyoma virus was undertaken.

Two strains (TS-a, TS-b) which were temperature sensitive in their plaque forming ability at 38.5˚C, but not at 31.5˚C, were isolated from a mutagenized stock of the polyoma wild type virus (PY). TS-a was studied in further detail.

TS-a grown at 31.5˚C was found to be indistinguishable from PY in a number of physical characteristics including the heat sensitivity of the completed viral components. TS-a was inhibited in its ability to produce infectious virus in mouse cells when incubated at 38.5˚C; this inhibition could be overcome by infection with high multiplicities.

The nature of the intracellular temperature sensitive step of TS-a was analysed to some degree. It was found that this step occurs after uncoating of the infecting virus particles and about the time of new viral DNA synthesis. New infectious viral DNA does not appear to be made at the nonpermissive temperature; in contrast noninfectious capsids are made at 38.5˚C, but in amounts smaller than a full yield, such as made by TS-a at 31.5˚C or by PY at both the high and low temperature.

TS-a has also been found to be temperature sensitive in its transforming ability in vitro. Cells transformed at 31.5˚C by TS-a retain their transformed characteristics upon cultivation at 38.5˚C. Thus the temperature sensitive function seems to be important for the initiation of transformation, but not essential for the maintenance of the transformed state. TS-a also appears to be temperature sensitive in the production of tumors in newborn hamsters.

Depth-sensitive analysis of fluorine on lunar sample surfaces and in carbonaceous chondrites by a nuclear resonant reaction technique

The nuclear resonant reaction ¹⁹F(ρ,αγ)¹⁶O has been used to perform depth-sensitive analyses of fluorine in lunar samples and carbonaceous chondrites. The resonance at 0.83 MeV (center-of-mass) in this reaction is utilized to study fluorine surface films, with particular interest paid to the outer micron of Apollo 15 green glass, Apollo 17 orange glass, and lunar vesicular basalts. These results are distinguished from terrestrial contamination, and are discussed in terms of a volcanic origin for the samples of interest. Measurements of fluorine in carbonaceous chondrites are used to better define the solar system fluorine abundance. A technique for measurement of carbon on solid surfaces with applications to direct quantitative analysis of implanted solar wind carbon in lunar samples is described.

Applications of a nuclear technique for depth-sensitive hydrogen analysis : trapped H in lunar samples and the hydration of terrestrial obsidian

The resonant nuclear reaction ¹⁹F(p,αy)¹⁶O has been used to perform depth-sensitive analyses for both fluorine and hydrogen in solid samples. The resonance at 0.83 MeV (center-of-mass) in this reaction has been applied to the measurement of the distribution of trapped solar protons in lunar samples to depths of ~1/2µm. These results are interpreted in terms of a redistribution of the implanted H which has been influenced by heavy radiation damage in the surface region. Fluorine determinations have been performed in a 1-µm surface layer on lunar and meteoritic samples using the same ¹⁹F(p,αy)¹⁶O resonance. The measurement of H depth distributions has also been used to study the hydration of terrestrial obsidian, a phenomenon of considerable archaeological interest as a means of dating obsidian artifacts. Additional applications of this type of technique are also discussed.

Determination of electronic energy levels of molecules by 90° low energy electron scattering

A review of the theory of electron scattering indicates that low incident beam energies and large scattering angles are the favorable conditions for the observation of optically forbidden transitions in atoms and molecules.

An apparatus capable of yielding electron impact spectra at 90° with incident electron beam energies between 30 and 50 electron volts is described. The resolution of the instrument is about 1 electron volt.

Impact spectra of thirteen molecules have been obtained. Known forbidden transitions to the helium 2³S, the hydrogen b³Ʃ⁺_u, the nitrogen A³Ʃ⁺_u, B³π_g, a’π_g, and C³π_u, the carbon monoxide a³π, the ethylene ᾶ³B_1u, and the benzene ᾶ³B_1u states from the corresponding ground states have been observed.

In addition, singlet-triplet vertical transitions in acetylene, propyne, propadiene, norbornadiene and quadricyclene, peaking at 5.9, 5.9, 4.5, 3.8, and 4.0 ev (±0.2 ev), respectively, have been observed and assigned for the first time.