Programmable logic design of a compact Genetic Algorithm for phasor estimation in real-time

The main objective of this work is to present an efficient method for phasor estimation based on a compact Genetic Algorithm (cGA) implemented in Field Programmable Gate Array (FPGA). To validate the proposed method, an Electrical Power System (EPS) simulated by the Alternative Transients Program (ATP) provides data to be used by the cGA. This data is as close as possible to the actual data provided by the EPS. Real life situations such as islanding, sudden load increase and permanent faults were considered. The implementation aims to take advantage of the inherent parallelism in Genetic Algorithms in a compact and optimized way, making them an attractive option for practical applications in real-time estimations concerning Phasor Measurement Units (PMUs).

Grid Connected Doubly Fed Induction Generator Based Wind Turbine under LVRT

This project concentrates on the Low Voltage Ride Through (LVRT) capability of Doubly Fed Induction Generator (DFIG) wind turbine. The main attention in the project is, therefore, drawn to the control of the DFIG wind turbine and of its power converter and to the ability to protect itself without disconnection during grid faults. It provides also an overview on the interaction between variable speed DFIG wind turbines and the power system subjected to disturbances, such as short circuit faults. The dynamic model of DFIG wind turbine includes models for both mechanical components as well as for all electrical components, controllers and for the protection device of DFIG necessary during grid faults. The viewpoint of this project is to carry out different simulations to provide insight and understanding of the grid fault impact on both DFIG wind turbines and on the power system itself. The dynamic behavior of DFIG wind turbines during grid faults is simulated and assessed by using a transmission power system generic model developed and delivered by Transmission System Operator in the power system simulation toolbox Digsilent, Matlab/Simulink and PLECS.

Biogas and bio-hydrogen: production and uses. A review

The first part of this essay aims at investigating the already available and promising technologies for the biogas and bio-hydrogen production from anaerobic digestion of different organic substrates. One strives to show all the peculiarities of this complicate process, such as continuity, number of stages, moisture, biomass preservation and rate of feeding. The main outcome of this part is the awareness of the huge amount of reactor configurations, each of which suitable for a few types of substrate and circumstance. Among the most remarkable results, one may consider first of all the wet continuous stirred tank reactors (CSTR), right to face the high waste production rate in urbanised and industrialised areas. Then, there is the up-flow anaerobic sludge blanket reactor (UASB), aimed at the biomass preservation in case of highly heterogeneous feedstock, which can also be treated in a wise co-digestion scheme. On the other hand, smaller and scattered rural realities can be served by either wet low-rate digesters for homogeneous agricultural by-products (e.g. fixed-dome) or the cheap dry batch reactors for lignocellulose waste and energy crops (e.g. hybrid batch-UASB). The biological and technical aspects raised during the first chapters are later supported with bibliographic research on the important and multifarious large-scale applications the products of the anaerobic digestion may have. After the upgrading techniques, particular care was devoted to their importance as biofuels, highlighting a further and more flexible solution consisting in the reforming to syngas. Then, one shows the electricity generation and the associated heat conversion, stressing on the high potential of fuel cells (FC) as electricity converters. Last but not least, both the use as vehicle fuel and the injection into the gas pipes are considered as promising applications. The consideration of the still important issues of the bio-hydrogen management (e.g. storage and delivery) may lead to the conclusion that it would be far more challenging to implement than bio-methane, which can potentially “inherit” the assets of the similar fossil natural gas. Thanks to the gathered knowledge, one devotes a chapter to the energetic and financial study of a hybrid power system supplied by biogas and made of different pieces of equipment (natural gas thermocatalitic unit, molten carbonate fuel cell and combined-cycle gas turbine structure). A parallel analysis on a bio-methane-fed CCGT system is carried out in order to compare the two solutions. Both studies show that the apparent inconvenience of the hybrid system actually emphasises the importance of extending the computations to a broader reality, i.e. the upstream processes for the biofuel production and the environmental/social drawbacks due to fossil-derived emissions. Thanks to this “boundary widening”, one can realise the hidden benefits of the hybrid over the CCGT system.

Time-domain modeling of high-frequency electromagnetic wave propagation, overhead wires, and earth

Prediction of radiated fields from transmission lines has not previously been studied from a panoptical power system perspective. The application of BPL technologies to overhead transmission lines would benefit greatly from an ability to simulate real power system environments, not limited to the transmission lines themselves. Presently circuitbased transmission line models used by EMTP-type programs utilize Carson’s formula for a waveguide parallel to an interface. This formula is not valid for calculations at high frequencies, considering effects of earth return currents. This thesis explains the challenges of developing such improved models, explores an approach to combining circuit-based and electromagnetics modeling to predict radiated fields from transmission lines, exposes inadequacies of simulation tools, and suggests methods of extending the validity of transmission line models into very high frequency ranges. Electromagnetics programs are commonly used to study radiated fields from transmission lines. However, an approach is proposed here which is also able to incorporate the components of a power system through the combined use of EMTP-type models. Carson’s formulas address the series impedance of electrical conductors above and parallel to the earth. These equations have been analyzed to show their inherent assumptions and what the implications are. Additionally, the lack of validity into higher frequencies has been demonstrated, showing the need to replace Carson’s formulas for these types of studies. This body of work leads to several conclusions about the relatively new study of BPL. Foremost, there is a gap in modeling capabilities which has been bridged through integration of circuit-based and electromagnetics modeling, allowing more realistic prediction of BPL performance and radiated fields. The proposed approach is limited in its scope of validity due to the formulas used by EMTP-type software. To extend the range of validity, a new set of equations must be identified and implemented in the approach. Several potential methods of implementation have been explored. Though an appropriate set of equations has not yet been identified, further research in this area will benefit from a clear depiction of the next important steps and how they can be accomplished. Prediction of radiated fields from transmission lines has not previously been studied from a panoptical power system perspective. The application of BPL technologies to overhead transmission lines would benefit greatly from an ability to simulate real power system environments, not limited to the transmission lines themselves. Presently circuitbased transmission line models used by EMTP-type programs utilize Carson’s formula for a waveguide parallel to an interface. This formula is not valid for calculations at high frequencies, considering effects of earth return currents. This thesis explains the challenges of developing such improved models, explores an approach to combining circuit-based and electromagnetics modeling to predict radiated fields from transmission lines, exposes inadequacies of simulation tools, and suggests methods of extending the validity of transmission line models into very high frequency ranges. Electromagnetics programs are commonly used to study radiated fields from transmission lines. However, an approach is proposed here which is also able to incorporate the components of a power system through the combined use of EMTP-type models. Carson’s formulas address the series impedance of electrical conductors above and parallel to the earth. These equations have been analyzed to show their inherent assumptions and what the implications are. Additionally, the lack of validity into higher frequencies has been demonstrated, showing the need to replace Carson’s formulas for these types of studies. This body of work leads to several conclusions about the relatively new study of BPL. Foremost, there is a gap in modeling capabilities which has been bridged through integration of circuit-based and electromagnetics modeling, allowing more realistic prediction of BPL performance and radiated fields. The proposed approach is limited in its scope of validity due to the formulas used by EMTP-type software. To extend the range of validity, a new set of equations must be identified and implemented in the approach. Several potential methods of implementation have been explored. Though an appropriate set of equations has not yet been identified, further research in this area will benefit from a clear depiction of the next important steps and how they can be accomplished.

Parameter estimation for transformer modeling

Large Power transformers, an aging and vulnerable part of our energy infrastructure, are at choke points in the grid and are key to reliability and security. Damage or destruction due to vandalism, misoperation, or other unexpected events is of great concern, given replacement costs upward of $2M and lead time of 12 months. Transient overvoltages can cause great damage and there is much interest in improving computer simulation models to correctly predict and avoid the consequences. EMTP (the Electromagnetic Transients Program) has been developed for computer simulation of power system transients. Component models for most equipment have been developed and benchmarked. Power transformers would appear to be simple. However, due to their nonlinear and frequency-dependent behaviors, they can be one of the most complex system components to model. It is imperative that the applied models be appropriate for the range of frequencies and excitation levels that the system experiences. Thus, transformer modeling is not a mature field and newer improved models must be made available. In this work, improved topologically-correct duality-based models are developed for three-phase autotransformers having five-legged, three-legged, and shell-form cores. The main problem in the implementation of detailed models is the lack of complete and reliable data, as no international standard suggests how to measure and calculate parameters. Therefore, parameter estimation methods are developed here to determine the parameters of a given model in cases where available information is incomplete. The transformer nameplate data is required and relative physical dimensions of the core are estimated. The models include a separate representation of each segment of the core, including hysteresis of the core, λ-i saturation characteristic, capacitive effects, and frequency dependency of winding resistance and core loss. Steady-state excitation, and de-energization and re-energization transients are simulated and compared with an earlier-developed BCTRAN-based model. Black start energization cases are also simulated as a means of model evaluation and compared with actual event records. The simulated results using the model developed here are reasonable and more correct than those of the BCTRAN-based model. Simulation accuracy is dependent on the accuracy of the equipment model and its parameters. This work is significant in that it advances existing parameter estimation methods in cases where the available data and measurements are incomplete. The accuracy of EMTP simulation for power systems including three-phase autotransformers is thus enhanced. Theoretical results obtained from this work provide a sound foundation for development of transformer parameter estimation methods using engineering optimization. In addition, it should be possible to refine which information and measurement data are necessary for complete duality-based transformer models. To further refine and develop the models and transformer parameter estimation methods developed here, iterative full-scale laboratory tests using high-voltage and high-power three-phase transformer would be helpful.

Transformer modeling ATP : internal faults & high-frequency discretization

Power transformers are key components of the power grid and are also one of the most subjected to a variety of power system transients. The failure of a large transformer can cause severe monetary losses to a utility, thus adequate protection schemes are of great importance to avoid transformer damage and maximize the continuity of service. Computer modeling can be used as an efficient tool to improve the reliability of a transformer protective relay application. Unfortunately, transformer models presently available in commercial software lack completeness in the representation of several aspects such as internal winding faults, which is a common cause of transformer failure. It is also important to adequately represent the transformer at frequencies higher than the power frequency for a more accurate simulation of switching transients since these are a well known cause for the unwanted tripping of protective relays. This work develops new capabilities for the Hybrid Transformer Model (XFMR) implemented in ATPDraw to allow the representation of internal winding faults and slow-front transients up to 10 kHz. The new model can be developed using any of two sources of information: 1) test report data and 2) design data. When only test-report data is available, a higher-order leakage inductance matrix is created from standard measurements. If design information is available, a Finite Element Model is created to calculate the leakage parameters for the higher-order model. An analytical model is also implemented as an alternative to FEM modeling. Measurements on 15-kVA 240?/208Y V and 500-kVA 11430Y/235Y V distribution transformers were performed to validate the model. A transformer model that is valid for simulations for frequencies above the power frequency was developed after continuing the division of windings into multiple sections and including a higher-order capacitance matrix. Frequency-scan laboratory measurements were used to benchmark the simulations. Finally, a stability analysis of the higher-order model was made by analyzing the trapezoidal rule for numerical integration as used in ATP. Numerical damping was also added to suppress oscillations locally when discontinuities occurred in the solution. A maximum error magnitude of 7.84% was encountered in the simulated currents for different turn-to-ground and turn-to-turn faults. The FEM approach provided the most accurate means to determine the leakage parameters for the ATP model. The higher-order model was found to reproduce the short-circuit impedance acceptably up to about 10 kHz and the behavior at the first anti-resonant frequency was better matched with the measurements.

OUT-OF-STEP DETECTION BASED ON ZUBOV’S APPROXIMATION BOUNDARY METHOD

Disturbances in power systems may lead to electromagnetic transient oscillations due to mismatch of mechanical input power and electrical output power. Out-of-step conditions in power system are common after the disturbances where the continuous oscillations do not damp out and the system becomes unstable. Existing out-of-step detection methods are system specific as extensive off-line studies are required for setting of relays. Most of the existing algorithms also require network reduction techniques to apply in multi-machine power systems. To overcome these issues, this research applies Phasor Measurement Unit (PMU) data and Zubov’s approximation stability boundary method, which is a modification of Lyapunov’s direct method, to develop a novel out-of-step detection algorithm. The proposed out-of-step detection algorithm is tested in a Single Machine Infinite Bus system, IEEE 3-machine 9-bus, and IEEE 10-machine 39-bus systems. Simulation results show that the proposed algorithm is capable of detecting out-of-step conditions in multi-machine power systems without using network reduction techniques and a comparative study with an existing blinder method demonstrate that the decision times are faster. The simulation case studies also demonstrate that the proposed algorithm does not depend on power system parameters, hence it avoids the need of extensive off-line system studies as needed in other algorithms.

Poner el cuerpo : La configuración narrativa del pícaro como crítica del sistema colonial de la Nueva España en El Periquillo Sarniento

El presente trabajo se propone analizar la novela El Periquillo Sarniento (1816) de Lizardi como un respuesta estética a los cambios históricos acaecidos en la sociedad de la Nueva España en los albores de la emancipación del sistema colonial español. Esta obra plantea las vicisitudes y hazañas de un letrado criollo por reposicionarse en un sistema de poder ya vetusto y asfixiante que presenta grietas en su construcción. El accionar de este narrador protagonista es analizado teniendo en cuenta los conceptos de "sujeto colonial" de Rolena Adorno, el de "pensamiento dialógico" de Nancy Vogeley y la "ambigüedad del picarismo" de Maurice Molho. El objetivo de este estudio es desentrañar la perspectiva novedosa que plantea Lizardi en torno a la utilidad del letrado en una sociedad de cambios tanto políticos como sociales

Poner el cuerpo : La configuración narrativa del pícaro como crítica del sistema colonial de la Nueva España en El Periquillo Sarniento

El presente trabajo se propone analizar la novela El Periquillo Sarniento (1816) de Lizardi como un respuesta estética a los cambios históricos acaecidos en la sociedad de la Nueva España en los albores de la emancipación del sistema colonial español. Esta obra plantea las vicisitudes y hazañas de un letrado criollo por reposicionarse en un sistema de poder ya vetusto y asfixiante que presenta grietas en su construcción. El accionar de este narrador protagonista es analizado teniendo en cuenta los conceptos de "sujeto colonial" de Rolena Adorno, el de "pensamiento dialógico" de Nancy Vogeley y la "ambigüedad del picarismo" de Maurice Molho. El objetivo de este estudio es desentrañar la perspectiva novedosa que plantea Lizardi en torno a la utilidad del letrado en una sociedad de cambios tanto políticos como sociales

Poner el cuerpo : La configuración narrativa del pícaro como crítica del sistema colonial de la Nueva España en El Periquillo Sarniento

El presente trabajo se propone analizar la novela El Periquillo Sarniento (1816) de Lizardi como un respuesta estética a los cambios históricos acaecidos en la sociedad de la Nueva España en los albores de la emancipación del sistema colonial español. Esta obra plantea las vicisitudes y hazañas de un letrado criollo por reposicionarse en un sistema de poder ya vetusto y asfixiante que presenta grietas en su construcción. El accionar de este narrador protagonista es analizado teniendo en cuenta los conceptos de "sujeto colonial" de Rolena Adorno, el de "pensamiento dialógico" de Nancy Vogeley y la "ambigüedad del picarismo" de Maurice Molho. El objetivo de este estudio es desentrañar la perspectiva novedosa que plantea Lizardi en torno a la utilidad del letrado en una sociedad de cambios tanto políticos como sociales

Modelación y simulación de la conexión a red de un parque eólico

Se tiene una red eléctrica compuesta por tres centrales térmicas convencionales y dos núcleos de consumo diferenciados, uno industrial y otro residencial, a la que se le va a conectar un parque eólico. El objetivo es dimensionar la línea de conexión y conocer el comportamiento de la red ante este cambio. Se han calculado las características de la línea eléctrica de conexión para satisfacer la potencia instalada del parque. También se ha estimado la demanda horaria de electricidad en las zonas residencial e industrial y se han tomado los valores horarios significativos de la potencia generada por el parque eólico, ambos, para las distintas estaciones del año. Como programa para la simulación de la red eléctrica se utilizó el PSS/E (Power System Simulator for Engineering) en el que, ayudándose del lenguaje de programación Python, se creó un código que cambiaba los datos horarios del consumo y la generación del parque, resolvía el flujo de cargas y exportaba los resultados que mostraban el comportamiento de la red para las distintas casuísticas. Finalmente, se analizaron los resultados de las potencias activa y reactiva generadas por las centrales convencionales, la tensión en los buses y las posibles sobrecargas.

A dual-band priority assignment algorithm for dynamic QoS resource management

Future high-quality consumer electronics will contain a number of applications running in a highly dynamic environment, and their execution will need to be efficiently arbitrated by the underlying platform software. The multimedia applications that currently execute in such similar contexts face frequent run-time variations in their resource demands, originated by the greedy nature of the multimedia processing itself. Changes in resource demands are triggered by numerous reasons (e.g. a switch in the input media compression format). Such situations require real-time adaptation mechanisms to adjust the system operation to the new requirements, and this must be done seamlessly to satisfy the user experience. One solution for efficiently managing application execution is to apply quality of service resource management techniques, based on assigning and enforcing resource contracts to applications. Most resource management solutions provide temporal isolation by enforcing resource assignments and avoiding any resource overruns. However, this has a clear limitation over the cost-effective resource usage. This paper presents a simple priority assignment scheme based on uniform priority bands to allow that greedy multimedia tasks incur in safe overruns that increase resource usage and do not threaten the timely execution of non-overrunning tasks. Experimental results show that the proposed priority assignment scheme in combination with a resource accounting mechanism preserves timely multimedia execution and delivery, achieves a higher cost-effective processor usage, and guarantees the execution isolation of non-overrunning tasks.

Practical Characterization of Input-Parallel-Connected Converters with a Common Input Filter

The paper presents a method to analyze robust stability and transient performance of a distributed power system consisting of commercial converter modules interconnected through a common input filter. The method is based on the use of four transfer functions, which are measurable from the converter input and output terminals. It is shown that these parameters provide important information on the power module sensitivity to the interactions caused by the external impedances. Practical characterization for the described system structure is performed introducing special transfer functions utilized for the interactions assessment. Experimental results are provided to support the presented analysis procedure.

Ecualización y optimización de la codificación para la simulación de sistemas OFDM

Los sistemas basados en la técnica OFDM (Multiplexación por División de Frecuencias Ortogonales) son una evolución de los tradicionales sistemas FDM (Multiplexación por División de Frecuencia), gracias a la cual se consigue un mejor aprovechamiento del ancho de banda. En la actualidad los sistemas OFDM y sus variantes ocupan un lugar muy importante en las comunicaciones, estando implementados en diversos estándares como pueden ser: DVB-T (estándar de la TDT), ADSL, LTE, WIMAX, DAB (radio digital), etc. Debido a ello, en este proyecto se implementa un sistema OFDM en el que poder realizar diversas simulaciones para entender mejor su funcionamiento. Para ello nos vamos a valer de la herramienta Matlab. Los objetivos fundamentales dentro de la simulación del sistema es poner a prueba el empleo de turbo códigos (comparándolo con los códigos convolucionales tradicionales) y de un ecualizador. Todo ello con la intención de mejorar la calidad de nuestro sistema (recibir menos bits erróneos) en condiciones cada vez más adversas: relaciones señal a ruido bajas y multitrayectos. Para ello se han implementado las funciones necesarias en Matlab, así como una interfaz gráfica para que sea más sencillo de utilizar el programa y más didáctico. En los capítulos segundo y tercero de este proyecto se efectúa un estudio de las bases de los sistemas OFDM. En el segundo nos centramos más en un estudio teórico puro para después pasar en el tercero a centrarnos únicamente en la teoría de los bloques implementados en el sistema OFDM que se desarrolla en este proyecto. En el capítulo cuarto se explican las distintas opciones que se pueden llevar a cabo mediante la interfaz implementada, a la vez que se elabora un manual para el correcto uso de la misma. El quinto capítulo se divide en dos partes, en la primera se muestran las representaciones que puede realizar el programa, y en la segunda únicamente se realizan simulaciones para comprobar que tal responde nuestra sistema a distintas configuraciones de canal, y las a distintas configuraciones que hagamos nosotros de nuestro sistema (utilicemos una codificación u otra, utilicemos el ecualizador o el prefijo cíclico, etc…). Para finalizar, en el último capítulo se exponen las conclusiones obtenidas en este proyecto, así como posibles líneas de trabajo que seguir en próximas versiones del mismo. ABSTRACT. Systems based on OFDM (Orthogonal Frequency Division Multiplexing) technique are an evolution of traditional FDM (Frequency Division Multiplexing). Due to the use of OFDM systems are achieved by more efficient use of bandwidth. Nowadays, OFDM systems and variants of OFDM systems occupy a very important place in the world of communications, being implemented in standards such as DVB-T, ADSL, LTE, WiMAX, DAB (digital radio) and another more. For all these reasons, this project implements a OFDM system for performing various simulations for better understanding of OFDM system operation. The system has been simulated using Matlab. With system simulation we search to get two key objectives: to test the use of turbo codes (compared to traditional convolutional codes) and an equalizer. We do so with the intention of improving the quality of our system (receive fewer rates of bit error) in increasingly adverse conditions: lower signal-to-noise and multipath. For these reasons necessaries Matlab´s functions have been developed, and a GUI (User Graphical Interface) has been integrated so the program can be used in a easier and more didactic way. This project is divided into five chapters. In the second and third chapter of this project are developed the basis of OFDM systems. Being developed in the second one a pure theoretical study, while focusing only on block theory implemented in the OFDM system in the third one. The fourth chapter describes the options that can be carried out by the interface implemented. Furthermore the chapter is developed for the correct use of the interface. The fifth chapter is divided into two parts, the first part shows to us the representations that the program can perform, and the second one just makes simulations to check that our system responds to differents channel configurations (use of convolutional codes or turbo codes, the use of equalizer or cyclic prefix…). Finally, the last chapter presents the conclusions of this project and possible lines of work to follow in future versions.

A self-adaptive image processing application based on evolvable and scalable hardware

Evolvable Hardware (EH) is a technique that consists of using reconfigurable hardware devices whose configuration is controlled by an Evolutionary Algorithm (EA). Our system consists of a fully-FPGA implemented scalable EH platform, where the Reconfigurable processing Core (RC) can adaptively increase or decrease in size. Figure 1 shows the architecture of the proposed System-on-Programmable-Chip (SoPC), consisting of a MicroBlaze processor responsible of controlling the whole system operation, a Reconfiguration Engine (RE), and a Reconfigurable processing Core which is able to change its size in both height and width. This system is used to implement image filters, which are generated autonomously thanks to the evolutionary process. The system is complemented with a camera that enables the usage of the platform for real time applications.