Heat losses and thermal performance of commercial combined solar and pellet heating systems

Various pellet heating systems are marketed in Sweden, some of them in combination with a solar heating system. Several types of pellet heating units are available and can be used for a combined system. This article compares four typical combined solar and pellet heating systems: System 1 and 2 two with a pellet stove, system 3 with a store integrated pellet burner and system 4 with a pellet boiler. The lower efficiency of pellet heaters compared to oil or gas heaters increases the primary energy demand. Consequently heat losses of the various systems have been studied. The systems have been modeled in TRNSYS and simulated with parameters identified from measurements. For almost all systems the flue gas losses are the main heat losses except for system 3 where store heat losses prevail. Relevant are also the heat losses of the burner and the boiler to the ambient. Significant leakage losses are noticed for system 3 and 4. For buildings with an open internal design system 1 is the most efficient solution. Other buildings should preferably apply system 3. The right choice of the system depends also on whether the heater is placed inside or outside of the heated are. A large potential for system optimization exist for all studied systems, which when applied could alter the relative merits of the different system types.

Combined solar and pellet heating systems for single-family houses : How to achieve decreased electricity usage, increased system efficiency and increased solar gains

In Sweden, there are about 0.5 million single-family houses that are heated by electricity alone, and rising electricity costs force the conversion to other heating sources such as heat pumps and wood pellet heating systems. Pellet heating systems for single-family houses are currently a strongly growing market. Future lack of wood fuels is possible even in Sweden, and combining wood pellet heating with solar heating will help to save the bio-fuel resources. The objectives of this thesis are to investigate how the electrically heated single-family houses can be converted to pellet and solar heating systems, and how the annual efficiency and solar gains can be increased in such systems. The possible reduction of CO-emissions by combining pellet heating with solar heating has also been investigated. Systems with pellet stoves (both with and without a water jacket), pellet boilers and solar heating have been simulated. Different system concepts have been compared in order to investigate the most promising solutions. Modifications in system design and control strategies have been carried out in order to increase the system efficiency and the solar gains. Possibilities for increasing the solar gains have been limited to investigation of DHW-units for hot water production and the use of hot water for heating of dishwashers and washing machines via a heat exchanger instead of electricity (heat-fed appliances). Computer models of pellet stoves, boilers, DHW-units and heat-fed appliances have been developed and the parameters for the models have been identified from measurements on real components. The conformity between the models and the measurements has been checked. The systems with wood pellet stoves have been simulated in three different multi-zone buildings, simulated in detail with heat distribution through door openings between the zones. For the other simulations, either a single-zone house model or a load file has been used. Simulations were carried out for Stockholm, Sweden, but for the simulations with heat-fed machines also for Miami, USA. The foremost result of this thesis is the increased understanding of the dynamic operation of combined pellet and solar heating systems for single-family houses. The results show that electricity savings and annual system efficiency is strongly affected by the system design and the control strategy. Large reductions in pellet consumption are possible by combining pellet boilers with solar heating (a reduction larger than the solar gains if the system is properly designed). In addition, large reductions in carbon monoxide emissions are possible. To achieve these reductions it is required that the hot water production and the connection of the radiator circuit is moved to a well insulated, solar heated buffer store so that the boiler can be turned off during the periods when the solar collectors cover the heating demand. The amount of electricity replaced using systems with pellet stoves is very dependant on the house plan, the system design, if internal doors are open or closed and the comfort requirements. Proper system design and control strategies are crucial to obtain high electricity savings and high comfort with pellet stove systems. The investigated technologies for increasing the solar gains (DHW-units and heat-fed appliances) significantly increase the solar gains, but for the heat-fed appliances the market introduction is difficult due to the limited financial savings and the need for a new heat distribution system. The applications closest to market introduction could be for communal laundries and for use in sunny climates where the dominating part of the heat can be covered by solar heating. The DHW-unit is economical but competes with the internal finned-tube heat exchanger which is the totally dominating technology for hot water preparation in solar combisystems for single-family houses.

Quantum control of electromagnetically induced transparency dispersion via atomic tunneling in a double-well Bose-Einstein condensate

Electromagnetically induced transparency (EIT) is an important tool for controlling light propagation and nonlinear wave mixing in atomic gases with potential applications ranging from quantum computing to table top tests of general relativity. Here we consider EIT in an atomic Bose-Einstein condensate (BEC) trapped in a double-well potential. A weak probe laser propagates through one of the wells and interacts with atoms in a three-level Lambda configuration. The well through which the probe propagates is dressed by a strong control laser with Rabi frequency Omega(mu), as in standard EIT systems. Tunneling between the wells at the frequency g provides a coherent coupling between identical electronic states in the two wells, which leads to the formation of interwell dressed states. The macroscopic interwell coherence of the BEC wave function results in the formation of two ultranarrow absorption resonances for the probe field that are inside of the ordinary EIT transparency window. We show that these new resonances can be interpreted in terms of the interwell dressed states and the formation of a type of dark state involving the control laser and the interwell tunneling. To either side of these ultranarrow resonances there is normal dispersion with very large slope controlled by g. We discuss prospects for observing these ultranarrow resonances and the corresponding regions of high dispersion experimentally.

Reduced-order output feedback controllers for discrete-time systems

This article considers the stabilization by output feedback controllers for discrete-time systems. The controller can place all of the closed-loop poles within a specified disk D(-α, 1/β), centred at (-α,0) with radius 1/β, where | - α|  + 1/β < 1. The design method involves the decomposition of the system into two portions. The first portion comprises of all of the poles that are lying outside of the specified disk. A reduced-order model is constructed for this portion. The second portion comprises of all of the remaining poles of the system and is characterized by an H_∞-norm bound. The controller design is then accomplished by using H_∞-control theory. It is shown that, subject to the solvability of an algebraic Riccati equation, output feedback controllers can be systematically derived. The order of the controller is low, and can be as low as the number of the open-loop poles that are lying outside of the specified disk. A step-by-step design algorithm is provided. Numerical examples are given to illustrate the attractiveness of the design method.

Constrained pole placement for linear systems using low-order output feedback controllers

The paper presents a simple approach to the problem of designing low-order output feedback controllers for linear continuous systems. The controller can place all of the closed-loop poles within a circle, C(- , 1/ β) , with centre at - and radius of 1/ β in the left half s-plane. The design method is based on transformation of the original system and then applying the bounded-real-lemma to the transformed system. It is shown that subjected to the solvability of an algebraic Riccati equation (ARE), output feedback controllers can then be systematically derived. Furthermore, the order of the controller is low and equals only the number of the open-loop poles lying outside the circle. A step-by-step design algorithm is given. Numerical examples are given to illustrate the design method.

Towards a multicultural world : identifying work systems, practices and employee attitudes that embrace diversity

The research program described focuses on identifying the role of organisational culture, as reflected in workplace systems and practices, and employee and group attitudes in the outcomes of interactions among dissimilar parties. A systematic, theory-testing approach underlies the program, which aims to both develop and validate the diversity openness construct. The Perceived Dissimilarity-Openness Moderator Model developed from the research asserts that the affective, cognitive and behavioural consequences of diversity depend in part upon the perception of difference and subsequent quality and magnitude of the response to the perceived dissimilarity. When individuals or social systems (groups or organisations) are diversity-closed, outcomes are predicted to be less positive than when they are diversity-open.

An efficient replicated data management approach for peer-to-peer systems

The availability of critical services and their data can be significantly increased by replicating them on multiple systems connected with each other, even in the face of system and network failures. In some platforms such as peer-to-peer (P2P) systems, their inherent characteristic mandates the employment of some form of replication to provide acceptable service to their users. However, the problem of how best to replicate data to build highly available peer-to-peer systems is still an open problem. In this paper, we propose an approach to address the data replication problem on P2P systems. The proposed scheme is compared with other techniques and is shown to require less communication cost for an operation as well as provide higher degree of data availability.

Designing Agent-Oriented Systems by Analysing Agent Interactions

We propose a preliminary methodology for agent-oriented software engineering based on the idea of agent interaction analysis. This approach uses interactions between undetermined agents as the primary component of analysis and design. Agents as a basis for software engineering are useful because they provide a powerful and intuitive abstraction which can increase the comprehensiblity of a complex design. The paper describes a process by which the designer can derive the interactions that can occur in a system satisfying the given requirements and use them to design the structure of an agent-based system, including the identification of the agents themselves. We suggest that this approach has the flexibility necessary to provide agent-oriented designs for open and complex applications, and has value for future maintenance and extension of these systems.

Towards a Monitoring Framework for Agent-Based Contract Systems

The behaviours of autonomous agents may deviate from those deemed to be for the good of the societal systems of which they are a part. Norms have therefore been proposed as a means to regulate agent behaviours in open and dynamic systems, and may be encoded in electronic contracts in order to specify the obliged, permitted and prohibited behaviours of agents that are signatories to such contracts. Enactment and management of electronic contracts thus enables the use of regulatory mechanisms to ensure that agent behaviours comply with the encoded norms. To facilitate such mechanisms requires monitoring in order to detect and explain violation of norms. In this paper we propose a framework for monitoring that is to be implemented and integrated into a suite of contract enactment and management tools. The framework adopts a non-intrusive approach to monitoring, whereby the states of a contract with respect to its contained norms can be inferred on the basis of messages exchanged. Specifically, the framework deploys agents that observe messages sent between contract signatories, where these messages correspond to agent behaviours and therefore indicate whether norms are, or are in danger of, being violated.

A Framework for Monitoring Agent-Based Normative Systems

The behaviours of autonomous agents may deviate from those deemed to be for the good of the societal systems of which they are a part. Norms have therefore been proposed as a means to regulate agent behaviours in open and dynamic systems, where these norms specify the obliged, permitted and prohibited behaviours of agents. Regulation can effectively be achieved through use of enforcement mechanisms that result in a net loss of utility for an agent in cases where the agent's behaviour fails to comply with the norms. Recognition of compliance is thus crucial for achieving regulation. In this paper we propose a generic architecture for observation of agent behaviours, and recognition of these behaviours as constituting, or counting as, compliance or violation. The architecture deploys monitors that receive inputs from observers, and processes these inputs together with transition network representations of individual norms. In this way, monitors determine the fulfillment or violation status of norms. The paper also describes a proof of concept implementation and deployment of monitors in electronic contracting environments.

A Framework for Monitoring Agent-Based Normative Systems

The behaviours of autonomous agents may deviate from those deemed to be for the good of the societal systems of which they are a part. Norms have therefore been proposed as a means to regulate agent behaviours in open and dynamic systems, where these norms specify the obliged, permitted and prohibited behaviours of agents. Regulation can effectively be achieved through use of enforcement mechanisms that result in a net loss of utility for an agent in cases where the agent’s behaviour fails to comply with the norms. Recognition of compliance is thus crucial for achieving regulation. In this paper we propose a generic architecture for observation of agent behaviours, and recognition of these behaviours as constituting, or counting as, compliance or violation. The architecture deploys monitors that receive inputs from observers, and processes these inputs together with transition network representations of individual norms. In this way, monitors determine the fulfillment or violation status of norms. The paper also describes a proof of concept implementation and deployment of monitors in electronic contracting environments.

The Open Provenance Model Core Specification (v1.1)

The Open Provenance Model is a model of provenance that is designed to meet the following requirements: (1) To allow provenance information to be exchanged between systems, by means of a compatibility layer based on a shared provenance model. (2) To allow developers to build and share tools that operate on such a provenance model. (3) To define provenance in a precise, technology-agnostic manner. (4) To support a digital representation of provenance for any 'thing', whether produced by computer systems or not. (5) To allow multiple levels of description to coexist. (6) To define a core set of rules that identify the valid inferences that can be made on provenance representation. This document contains the specification of the Open Provenance Model (v1.1) resulting from a community-effort to achieve inter-operability in the Provenance Challenge series.

Mapping Attribution Metadata to the Open Provenance Model

A description of a data item's provenance can be provided in dierent forms, and which form is best depends on the intended use of that description. Because of this, dierent communities have made quite distinct underlying assumptions in their models for electronically representing provenance. Approaches deriving from the library and archiving communities emphasise agreed vocabulary by which resources can be described and, in particular, assert their attribution (who created the resource, who modied it, where it was stored etc.) The primary purpose here is to provide intuitive metadata by which users can search for and index resources. In comparison, models for representing the results of scientific workflows have been developed with the assumption that each event or piece of intermediary data in a process' execution can and should be documented, to give a full account of the experiment undertaken. These occurrences are connected together by stating where one derived from, triggered, or otherwise caused another, and so form a causal graph. Mapping between the two approaches would be benecial in integrating systems and exploiting the strengths of each. In this paper, we specify such a mapping between Dublin Core and the Open Provenance Model. We further explain the technical issues to overcome and the rationale behind the approach, to allow the same method to apply in mapping similar schemes.

Building agent-based hybrid intelligent systems

Many complex problems including financial investment planning, foreign exchange trading, knowledge discovery from large/multiple databases require hybrid intelligent systems that integrate many intelligent techniques including expert systems, fuzzy logic, neural networks, and genetic algorithms. However, hybrid intelligent systems are difficult to develop because they have a large number of parts or components that have many interactions. On the other hand, agents offer a new and often more appropriate route to the development of complex systems, especially in open and dynamic environments. In this paper, it is argued that agent technology is well snited for constructing hybrid intelligent systems (especially loosely coupled hybrid intelligent systems) through a successful case study. A great number of heterogeneous computing techniques/packages are easily integlated into the experimental system under a unifying agent framework, which implies that agent technology can greatly facilitate the construction of hybrid intelligent systems.

From product centricism to systems-wide education design: making corporate technology systems work for the learning organisation

Deakin University has established a major integrated corporate technology infrastructure in the last two years to enhance and bring together its distance education and on-campus education. This environment has been called Deakin Online. With Deakin Online rapidly developing, efforts are beginning to focus more fundamentally on how the potentials of the environment can be realised to create enduring teaching and learning value. This search must be understood in the context of the University’s commitment to the values of relevance, responsiveness and innovation. The question is: how can these values be realised in the digitally-based evolving educational enterprise using the new corporate technologies and new concepts of organisational structure and function? We argue for the transforming role of the academic teacher and new forms of open academic collegiality as being critical to realise strategic and enduring educational value. Moreover, change in role and process needs to be grounded in more systemic organisation and program-wide approaches to designing and working within the new contemporary learning environments. We believe the shift from the dangers of product centricism to system-wide education design modelling situating e-learning within broader curricular and pedagogical concerns represents the best strategy to create enduring educational benefits for all stakeholder groups (notably academic teachers and their learners) while preserving teachers’ sense of agency in the changing learning environments of higher education.