农牧交错区主要植物的氮素利用效率

Berendse&Aerts (1987)认为氮素利用效率(nitrogen use efficiency，NUE)可以分为两部分的乘积，即：①氮素生产力(nitrogen productivity，NP)，②氮素的平均滞留时间(mean residencetime，MRT)。本文利用这一概念对处于我国北方农牧交错带的内蒙古自治区多伦县典型植物的氮素利用策略进行了研究。研究假设：植物在贫瘠生境上所采取的氮素适应策略主要是提高对所吸收氮素的保持能力(较长的MRT)，而不是提高NUE。 在不同土壤生境上，属于不同生活型的不同物种其NP和MRT之间存在负相关关系。在不同生境、生活型和物种之间，作为NP与MRT乘积的NUE比NP、MRT的变化相对要小，结果表明植物主要通过延长MRT来适应氮素贫瘠的生境。因为NP与MRT相反的方向变化，二者不能同时增加或减少，所以NP与MRT之间存在相互协调(trade-off)的关系。 在群落和生态系统水平上，NP与MRT之间也存在相互协调关系，不同水平上的NUE之间也存在一定的联系。除了在种间存在这种关系外，通过对多伦县和十三里滩两种针茅（大针茅、克氏针茅）的氮素利用特征的研究，发现在种内，NP与MRT之间也存在这种相互协调关系。NUE与土壤供氮能力有关，随着土壤供氮能力的下降，NUE呈上升趋势。植物的NUE不仅与土壤的供氮能力有关，其它因素如土壤水分供应状况也会对植物的NUE产生影响，例如，与生长在河岸上的植物相比，生长在河滩湿地上的植物具有较高的NP，但MRT却较低。在群落中，不同植物个体的NUE及其组成参数NP和MRT也存在较大的差异，较大的植株具有较高的NP和MRT，因而NUE也高于个体较小的植株。本文研究结果表明，植物的NUE与氮素回收转移特性密切相关，植物提高氮素回收效率(nitrogen resorption efficiency，NRE)可以延长MRT，从而提高NUE。

Hydrological studies of Matatilla Reservoir, Uttar Pradesh

Matatilla Reservoir, located in semi arid region, (Lat. 25 degree 15'N and Long. 78 degree 23'E) has an area (at FRL) of 13,893 ha, volume and shore development 0.663 and 1.65, shoreline 73.6 km. Volume and shore development indicate that greater part of the reservoir is shallow, which is a favourable point for fish productivity. Temperature and dissolved oxygen gradually decreased with the increase in depth. Carbon dioxide was absent from the surface but invariably present in the bottom (3.6 ppm) pH remained alkaline (7.2-8.4 ppm) throughout the year. Alkalinity, chloride, calcium, magnesium, hardness and priductivity was maximum in pre-monsoon and minimum in monsoon except for calcium and manganesium in post-monsoon. Phosphate, nitrogen and ammonical nitrogen were found in traces. These variations may be due to influx and outflow of water and use of reservoir water for multipurpose activities.

MECHANISMS OF ABRASIVE WEAR IN A BORONIZED ALLOY STEEL.

This paper describes the effects of abrasive hardness and size on the 2-body abrasive wear mechanisms of a boronized low alloy steel. It is found that the wear resistance of the boronized steel is much greater against alumina abrasive than against silicon carbide. This difference in wear resistance is much enhanced when the particle size or the applied load is increased. Scanning electron microscopy of the worn specimens and of the used abrasive papers revealed that the enhanced difference in wear resistance between coarse alumina and silicon carbide papers is due to a change in the wear mechanism produced by silicon carbide papers with increasing abrasive particle size.

Effect of some environmental factors on the acute toxicity of deltamethrin to common carp: a laboratory study under aerobic condition

The toxicity of xenobiotic in aquatic ecosystems is influenced by many factors such as ambient temperature, water hardness, pond soil type, etc. In the present study, it was observed that air temperature, water hardness and soil sediment have profound influence on the toxicity of deltamethrin to common carp fry (ay. length 3.5 ± 0.5 cm, ay. weight 0.58 ± 0.25 g); 96h LC(sub)50 values for common carp at 38.07 ± 2.20°C maximum and 27.86 ± 1.22°C minimum air temperature in soft and very hard water were 0.102 and 0.495 µg lˉ¹, respectively. This value had increased significantly to 2.37 and 3.02 µg at 30.55 ± 1.21°C maximum and 26.04 ± 0.61°C minimum air temperature, respectively. When sediment was included, 96h LC(sub)50 at 38.07°C maximum temperature in very hard water was 1.808 µg 1ˉ¹ and this had increased to 8.073 µg 1ˉ¹ when tested at 30.55°C maximum temperature. Due to the 7.5°C increase in maximum and 1.7°C in minimum temperature, toxicity increased significantly. Lower toxicity in very hard water in comparison to soft water may be due to the lower solubility of deltarnethrin and high level of calcium. Adsorption reaction of deltamethrin with clay, humus, FeOOH, MnOOH and particulate organic carbon, and complexation reaction with dissolved organic carbon were responsible for the lowered toxicity in the experiment with sediment. Exposure time had no significant effect on acute toxicity of deltamethrin.

Influence of some abiotic factors on the acute toxicity of cadmium to Cyprinus carpio

Hardness of water had significant effect on the acute toxicity of cadmium to common carp, Cyprinus carpio. The 96h LC sub(50) and safe application rate increased from 43.17 and 22.77 mg 1 super(-1) in soft water (0.9 mM Ca super(2+) l super(-1)) to 310.48 and 177.66 mg l super(-1), respectively, in very hard water (6.0 mM Ca super(2+) l super(-1)). In medium hard and hard water, 96h LC sub(50) values were 48.39 and 116.45 mg l super(-1). When sediments were included in the medium hard, hard and very hard water treatments, the 96h LC sub(50) were 111.20, 133.71 and 334.47 mg l super(-1), respectively. Among these values, the one for medium hard water with sediment treatment was significantly higher than medium hard water treatment; values for the other two treatments were non-significant when compared with respective water treatments. Sediment was able to reduce the acute toxicity of cadmium mainly due to the complexation of cadmium with dissolved organic carbon (DOC). At the lower hardness level, cadmium complexed with DOC and the acute toxicity was reduced significantly. At higher hardness, most of the DOC sites were occupied by calcium and the acute toxicity of cadmium was not significantly reduced in hard water with sediment and very hard water with sediment experiments in comparison to respective water treatments.

Influence of particle properties on the erosive wear of sintered boron carbide

Sintered boron carbide is very hard, and can be an attractive material for wear-resistant components in critical applications. Previous studies of the erosion of less hard ceramics have shown that their wear resistance depends on the nature of the abrasive particles. Erosion tests were performed on a sintered boron carbide ceramic with silica, alumina and silicon carbide erodents. The different erodents caused different mechanisms of erosion, either by lateral cracking or small-scale chipping; the relative values of the hardness of the erodent and the target governed the operative mechanism. The small-scale chipping mechanism led to erosion rates typically an order of magnitude lower than the lateral fracture mechanism. The velocity exponents for erosion in the systems tested were similar to those seen in other work, except that measured with the 125 to 150 μm silica erodent. With this erodent the exponent was initially high, then decreased sharply with increasing velocity and became negative. It was proposed that this was due to deformation and fragmentation of the erodent particles. In the erosion testing of ceramics, the operative erosion mechanism is important. Care must be taken to ensure that the same mechanism is observed in laboratory testing as that which would be seen under service conditions, where the most common erodent is silica.

Inference approach to grammar construction

A system of computer assisted grammar construction (CAGC) is presented in this paper. The CAGC system is designed to generate broad-coverage grammars for large natural language corpora by utilizing both an extended inside-outside algorithm and an automatic phrase bracketing (AUTO) system which is designed to provide the extended algorithm with constituent information during learning. This paper demonstrates the capability of the CAGC system to deal with realistic natural language problems and the usefulness of the AUTO system for constraining the inside-outside based grammar re-estimation. Performance results, including coverage, recall and precision, are presented for a grammar constructed for the Wall Street Journal (WSJ) corpus using the Penn Treebank.

The effect of surface hardening on the elastic shakedown of elliptical contacts

The effect of varying both the aspect ratio and the coefficient of friction of contacts with elliptical geometry on their elastic shakedown performance has been examined theoretically for surfaces with two types of subsurface hardness or strength profiles. In stepwise hardening the hard layer is of uniform strength while in linear hardening its strength reduces from a maximum at the surface to that of the core at the base of the hardened layer. The shakedown load is expressed as the ratio of the maximum Hertzian pressure to the strength of the core material. As the depth of hardening, expressed as a multiple of the elliptical semi-axis, is increased so the potential shakedown load increases from a level that is appropriate to a uniform half-space of unhardened material to a value reflecting the hardness of the surface and near-surface material. In a step-hardened material, the shakedown limit for a surface 'pummelled' by the passage of a sequence of such loads reaches a cut-off or plateau value, which cannot be exceeded by further increases in hardening depth irrespective of the value of the friction coefficient. For a linear-hardened material the corresponding plateau is approached asymptotically. The work confirms earlier results on the upper bounds on shakedown of both point and line contacts and provides numerical values of shakedown loads for intermediate geometries. In general, the case depth required to achieve a given shakedown limit reduces in moving from a transversely moving nominal line load to an axisymmetric point load.

A comparison of power losses for small (< 1 kW) induction motor drives adopting squarewave and sinusoidal PWM excitation

In this paper the influence of the form of motor excitation on the performance of a small (< 1 kW) induction motor drive is studied. Two forms of excitation, namely sine waves generated by pulse width modulation and simple square wave are explored. Sine wave excitation gives lower motor losses but increases inverter losses. Conversely, square wave excitation increases motor losses but decreases inverter losses. Losses have been measured directly by calorimetric means or, in the case of the inverter, predicted by a Pspice model that has been verified by calorimetric methods. The work shows that overall, the use of square wave excitation leads to a more efficient drive. © 2004 The Institution of Electrical Engineers.

Laser micromachining of sputtered DLC films

DLC films with different thicknesses (from 100 nm to 1.9 μm) were deposited using sputtering of graphite target in pure argon atmosphere without substrate heating. Film microstructures (sp2/sp3 ratio) and mechanical properties (modulus, hardness, stress) were characterized as a function of film thickness. A thin layer of aluminum about 60 nm was deposited on the DLC film surface. Laser micromachining of Al/DLC layer was performed to form microcantilever structures, which were released using a reactive ion etching system with SF6 plasma. Due to the intrinsic stress in DLC films and bimorph Al/DLC structure, the microcantilevers bent up with different curvatures. For DLC film of 100 nm thick, the cantilever even formed microtubes. The relationship between the bimorph beam bending and DLC film properties (such as stress, modulus, etc.) were discussed in details. © 2005 Elsevier B.V. All rights reserved.

Analytical techniques for indentation of viscoelastic materials

Indentation of linearly viscoelastic materials is explored using elastic-viscoelastic correspondence analysis for both conical-pyramidal and spherical indentation. Boltzmann hereditary integrals are used to generate displacement-time solutions for loading at constant rate and creep following ramp loading. Experimental data for triangle- and trapezoidal-loading are examined for commercially-available polymers and compared with analytical solutions. Emphasis is given to the use of multiple experiments to test the fidelity and predictive capability of the obtained material creep function. Plastic deformation occurs in sharp indentation of glassy polymers and is found to complicate the viscoelastic analysis. A new method is proposed for estimating a material time-constant from peak displacement or hardness data obtained in pyramidal indentation tests performed at different loading rates.

Friction of sliding surfaces carrying adsorbed lubricant layers

In concentrated contacts the behaviour of lubricants is much modified by the high local pressures: changes can arise both from molecular ordering within the very thin film lubricant layers present at the interface as well as from the deposition on the component surfaces of more solid-like polymeric boundary layers. These 'third bodies' separating the solid surfaces may have rheological or mechanical properties very different from those observed in the bulk. Classical elasto-hydrodynamic theory considers the entrapped lubricant to exhibit a piezo-viscous behaviour while the conventional picture of more solid boundary lubricant layers views their shear strength r as being linearly dependent on local pressure p, so that T = TO + ap where TO and a are constants. If TO is relatively small, then the coefficient of friction \i = T Ip ~ a and so Amonton's laws are recovered. However, the properties of adsorbed or deposited surface films, or indeed other third bodies such as debris layers, may be more complex than this. A preliminary study has looked quantitatively at the influence of the pressure dependence of the shear strength of any surface layer on the overall friction coefficient of a contact which is made up of an array of asperities whose height varies in a Gaussian manner. Individual contact points may be elastic or plastic. The analysis results in plots of coefficient of friction versus the service or load parameter PIH&NRa where P is the nominal pressure on the contact, HS the hardness of the deforming surface, N the asperity density, R the mean radius of curvature of the asperities, and a is the standard deviation of their height distribution. In principle, any variation oft withp can be incorporated into the model; however, in this initial study we have used data on colloidal suspensions from the group at the Ecole Centrale de Lyon as well as examining the effect of functional relationships of somewhat greater complexity than a simple linear form. Results of the analysis indicate that variations in fj. are possible as the load is varied which depend on the statistical spread of behaviour at individual asperity contacts. The value of this analysis is that it attempts to combine the behaviour of films on the molecular scale with the topography of real engineering surfaces and so give an indication of the effects at the full-size or macro-scale that can be achieved by chemical or molecular surface engineering.

Effect of weathering on the mechanical properties of automotive clearcoats

The effect of weathering on the wear resistance of automotive clearcoats has been evaluated. Acrylic-based and urethane-based coatings were exposed in Florida, Belgium and Australia and also under accelerated conditions to SAE J1960 with 0.55 W m -2 borosilicate/borosilicate filtered xenon arc light. Weathering caused a significant reduction in the abrasion and erosion resistance of the clearcoats and large increases in their hardness. Accelerated weathering produced different effects from natural exposure.

A COMPARATIVE-STUDY OF KARYOTYPES OF MUNTJACS BY CHROMOSOME PAINTING

We have used a combination of chromosome sorting, degenerate oligonucleotide-primed polymerase chain reaction (DOP-PCR), chromosome painting and digital image capturing and processing techniques for comparative chromosome analysis of members of the genus Muntiacus. Chromosome-specific ''paints'' from a female Indian muntjac were hybridised to the metaphase chromosomes of the Gongshan, Black, and Chinese muntjac by both single and three colour chromosome painting. Karyotypes and idiograms for the Indian, Gongshan, Black and Chinese muntjac were constructed, based on enhanced 4', 6-diamidino-2-phenylindole (DAPI) banding patterns. The hybridisation signal for each paint was assigned to specific bands or chromosomes for all of the above muntjac species. The interspecific chromosomal homology was demonstrated by the use of both enhanced DAPI banding and comparative chromosome painting. These results provide direct molecular cytogenetic evidence for the tandem fusion theory of the chromosome evolution of muntjac species.