Síntese e caracterização de catalisadores nanométricos de LaSrNiO4 para aplicação em dessulfurização de tiofeno

The mixed metal oxides constitute an important class of catalytic materials widely investigated in different fields of applications. Studies of rare earth nickelates have been carried by several researchers in order to investigate the structural stability afforded by oxide formed and the existence of catalytic properties at room temperature. So, this study aims synthesize the nanosized catalyst of nickelate of lanthanum doped with strontium (La(1-x)SrxNiO4-d; x = 0,2 and 0,3), through the Pechini method and your characterization for subsequent application in the desulfurization of thiophene reaction. The precursor solutions were calcined at 300ºC/2h for pyrolysis of polyester and later calcinations occurred at temperatures of 500 - 1000°C. The resulting powders were characterized by thermogravimetric analysis (TG / DTG), surface area for adsorption of N2 by BET method, X-ray diffraction (XRD), scanning electron microscopy (HR_SEM) and spectrometry dispersive energy (EDS). The results of XRD had show that the perovskites obtained consist of two phases (LSN and NiO) and from 700ºC have crystalline structure. The results of SEM evidenced the obtainment of nanometric powders. The results of BET show that the powders have surface area within the range used in catalysis (5-50m2/g). The characterization of active sites was performed by reaction of desulfurization of thiophene at room temperature and 200ºC, the relation F/W equal to 0,7 mol h-1mcat -1. The products of the reaction were separated by gas chromatography and identified by the selective detection PFPD sulfur. All samples had presented conversion above 95%

Degradação do PMMA através da reação despolimerização uitlizando catalisadores de óxidos mistos

In this work, mixed oxides were synthesized by two methods: polymeric precursor and gel-combustion. The oxides, Niquelate of Lanthanum, Cobaltate of Lanthanum and Cuprate of Lanthanum were synthesized by the polymeric precursor method, and treated at 300 º C for 2 hours, calcined at 800 º C for 6h in air atmosphere. In gel-combustion method were produced and oxides using urea and citric acid as fuel, forming for each fuel the following oxides Ferrate of Lanthanum, Cobaltato of Lanthanum and Ferrato of Cobalt and Lanthanum, which were submitted to the combustion process assisted by microwave power maximum of 10min. The samples were characterized by: thermogravimetric analysis, X-ray diffraction; fisisorção of N2 (BET method) and scanning electron microscopy. The reactions catalytic of depolymerization of poly (methyl methacrylate), were performed in a reactor of silica, with catalytic and heating system equipped with a data acquisition system and the gas chromatograph. For the catalysts synthesized using the polymeric precursor method, the cuprate of lanthanum was best for the depolymerization of the recycled polymer, obtaining 100% conversion in less time 554 (min), and the pure polymer, was the Niquelate of Lanthanum, with 100% conversion in less time 314 (min). By gel-combustion method using urea as fuel which was the best result obtained Ferrate of Lanthanum for the pure polymer with 100% conversion in less time 657 (min), and the recycled polymer was Cobaltate of Lanthanum with 100 % conversion in less time 779 (min). And using citric acid to obtain the best result for the pure polymer, was Ferrate of Lanthanum with 100% conversion in less time 821 (min and) for the recycled polymer, was Ferrate of Lanthanum with 98.28% conversion in less time 635 (min)

Adição do resíduo de biomassa da cana-de-açúcar em pastas para cimentação de poços petrolíferos produtores de óleos pesados

The Potiguar basin has large fields of viscous oil where the used method for recovering is based on vapor injection; this operation is carried out by injecting vapor in the oilwell directly, without the protection of a revetment through thermal insulation, what causes its dilation and, consequently, cracks in the cement placed on the annular, and lost of hydraulic insulation; this crack is occasioned by the phenomenon of retrogression of the compressive resistance due to the conversion of the hydrated calcium silicate in phases calcium-rich, caused by the high temperatures in the wells, subjected to thermal recuperation. This work has evaluated the application of composite pastes with addition of residue of biomass of ground sugar-cane bagasse as anti-retrogression mineral admixture for cementation of oil-wells subjected to thermal recuperation. The addition of the mineral residue was carried out considering a relative amount of 10, 20, 30, 40 and 59% in relation to cement mass, trying to improve the microstructure of the paste, still being developed a reference paste only with cement and a paste with addition of 40% of silica flour - renowned material in the oil industry as anti-retrogression additive. Pozzolanic activity of the ash was evaluated through XRD, TG/DTG, as the resistance to compression, and it was also determined the physical and mechanical behavior of the pastes when submitted to cure at low temperatures (22 and 38º C); besides it was evaluated the behavior of the pastes when submitted to two cycles of cure at high temperature (280ºC) and pressure (7 MPa). It was verified that the ash of the sugar-cane biomass presents pozzolanic reaction and has great efficiency in decrease the permeability of the paste by filler effect, as well as that addition of ash in a relative amount of 10, 20 e 30% increases cured compressive resistance at low temperatures. It was also showed that the ash in a relative amount of 40% and 59% has very significant efficiency as anti-retrogression additive, since it prevents the decrease of compressive resistance and forms hydrated calcium silicate type xenotlita and tobermorita which have more resistance and stability in high temperatures

Preparação, caracterização e aplicação de derivados do ácido 12- tungstofosfórico suportado em SBA-15

Dissertação (mestrado)—Universidade de Brasília, Instituto de Química, Programa de Pós-Graduação em Química, 2016.

Efeito da incorporação de diatomita na estabilidade e permeabilidade de compósitos cimentíceos espumados aplicados a poços de petróleo

Lightweight oilwell cement slurries have been recently studied as a mean to improve zonal isolation and sheath-porous formation adherence. Foamed slurries consisting of Portland cement and air-entraining admixtures have become an interesting option for this application. The loss in hydrostatic pressure as a consequence of cement hydration results in the expansion of the air bubbles entrapped in the cement matrix, thus improving the sheath-porous formation contact. Consequently, slurries are able to better retain their water to complete the hydration process. The main objective of the present study was to evaluate the effect of the addition of an air-entraining admixture on the density, stability and permeability of composite slurries containing Portland cement and diatomite as light mineral load. Successful formulations are potential cementing materials for low fracture gradient oilwells. The experimental procedures used for slurry preparation and characterization were based on the American Petroleum Institute and ABNT guidelines Slurries containing a pre-established concentration of the air-entraining admixture and different contents of diatomite were prepared aiming at final densities of 13 to 15 lb/gal. The results revealed that the reduction of 15 to 25% of the density of the slurries did not significantly affect their strength. The addition of both diatomite and the air-entraining admixture increased the viscosity of the slurry providing better air-bubble retention in the volume of the slurry. Stable slurries depicted bottom to top density variation of less than 1.0 lb/gal and length reduction of the stability sample of 5.86 mm. Finally, permeability coefficient values between 0.617 and 0.406 mD were obtained. Therefore, lightweight oilwell cement slurries depicting a satisfactory set of physicochemical and mechanical properties can be formulated using a combination of diatomite and air-entraining admixtures for low fracture gradient oilwells

Membrana de alumina anódica: comportamento da microestrutura e estudo das propriedades ópticas após tratamento térmico

Thin commercial aluminum electrolytic and passed through reactions was obtained with anodic alumina membranes nanopores. These materials have applications in areas recognized electronic, biomedical, chemical and biological weapons, especially in obtaining nanostructures using these membranes as a substrate or template for processing nanowires, nanodots and nanofibers for applications noble. Previous studies showed that the membranes that have undergone heat treatment temperature to 1300° C underwent changes in morphology, crystal structure and optical properties. This aim, this thesis, a study of the heat treatment of porous anodic alumina membranes, in order to obtain and to characterize the behavior changes structures during the crystallization process of the membranes, at temperatures ranging between 300 and 1700° C. It was therefore necessary to mount a system formed by a tubular furnace resistive alumina tube and controlled environment, applying flux with special blend of Ag-87% and 13% N2, in which argon had the role of carrying out the oxygen nitrogen system and induce the closing of the pores during the densification of the membrane. The duration of heat treatment ranged from 60 to 15 minutes, at temperatures from 300 to 1700° C respectively. With the heat treatment occurred: a drastic reduction of porosity, grain growth and increased translucency of the membrane. For the characterization of the membranes were analyzed properties: Physical - thermogravimetric, X-ray diffraction, BET surface area; morphological - SEM, EDS through compositional and, optical absorbance, and transmittance in the UV-VIS, and FTIR. The results using the SEM showed that crystallization has occurred, densification and significant changes in membrane structure, as well as obtaining microtube, the BET analysis showed a decrease in specific surface area of the membranes has to 44.381 m2.g-1 to less than 1.8 m2.g-1 and in the analysis of transmittance and absorbance was found a value of 16.5% in the range of 800 nm, characteristic of the near infrared and FTIR have confirmed the molecular groups of the material. Thus, one can say that the membranes were mixed characteristics and properties which qualify for use in gas filtration system, as well as applications in the range of optical wavelength of the infra-red, and as a substrate of nanomaterials. This requires the continuation and deepening of additional study

Nanofiltração na produção de vinhos: redução de acidez volátil e de compostos fenólicos indesejados

Dissertação de Mestrado, Engenharia Biológica, Faculdade de Ciências e Tecnologias, Universidade do Algarve, 2014

Síntese e caracterização de catalisadores de LaNiO3 não suportados e suportados em Al2O3 e ZrO2 para a reforma a vapor do metano

Ionic oxides with ABO3 structure, where A represents a rare earth element or an alkaline metal and B is a transition metal from group VIII of the periodic table are potential catalysts for oxidation and good candidates for steam reforming reaction. Different methods have been considered for the synthesis of the oxide materials with perovskite structure to produce a high homogeneous material with low amount of impurities and low calcination temperatures. In the current work, oxides with the LaNiO3 formula had been synthesized using the method of the polymeric precursors. The thermal treatment of the materials took place at 300 ºC for 2h. The material supported in alumina and/or zirconia was calcined at 800 ºC temperature for 4h. The samples had been characterized by the following techniques: thermogravimetry; infrared spectroscopy; X-ray diffraction; specific surface area; distribution of particle size; scanning electron microscopy and thermo-programmed reduction. The steam reforming reaction was carried out in a pilot plant using reducing atmosphere in the reactor with a mixture of 10% H2-Argon, a mass about 5g of catalyst, flowing at 50 mL.min-1. The temperature range used was 50 - 1000 oC with a heating rate of 10 oC.min-1. A thermal conductivity detector was used to analyze the gas after the water trapping, in order to permit to quantify the consumption of hydrogen for the lanthanum nickelates (LaNiO3). The results showed that lanthanum nickelate were more efficient when supported in alumina than when supported in zirconia. It was observed that the methane conversion was approximately 100% and the selectivity to hydrogen was about 70%. In all cases were verified low selectivity to CO and CO2

Factores relacionados a sépsis neonatal. Unidad de Neonatología Clínica Humanitaria-Fundación Pablo Jaramillo

Se realizó un estudio observacional en recién nacidos sépticos ocurridos en la Unidad de Neonatología de la Fundación Humanitaria Pablo Jaramillo, durante el período de enero de 2009 a diciembre de 2011, con el objetivo de analizar la incidencia de antecedentes maternos y parámetros propios del recién nacido como posibles factores de riesgo para la sepsis, los parámetros de laboratorio que contribuyen a diagnosticar procesos infecciosos en el recién nacido y el desenlace que tuvieron los mismos. Durante este tiempo ingresaron 164 casos con riesgo de sepsis, sospecha de sepsis y sepsis bacteriana (42.62 /1000 nacidos vivos) y la mortalidad fue del 3.04%. Predominó la sepsis de inicio precoz sobre la tardía. Los principales antecedentes maternos fueron la ruptura prematura de membranas seguido de la infección de vías urinarias. En cuanto a los factores del recién nacido prevaleció el sexo masculino, prematurez y de bajo peso al nacer

Prevalencia y factores de riesgo de la colonización por estreptococo del grupo B en recien nacidos del área de maternidad del Hospital Vicente Corralo Moscoso de la ciudad de Cuenca de diciembre del 2005 a junio del 2006

Se estudiaron quinientos recién nacidos productos de parto virginal, mediante hisopado se recolectaron muestras de secreción de conducto auditivo externo, faringe y muestra de aspirado gástrico. El cultivo se re4alizó en agar sangre de carnero desfibrinada al 5% identificándose el germen mediante el tipo de hemólisis, la susceptibilidad a la prueba de bacitracina, sulfametoxasol/trimetoprim, y la confirmación mediante la prueba de aglutinación de látex (streptex) específica para el estreptococo del grupo B (EGB). Resultados: la prevalencia de colonización por estreptococo del grupo B en recién nacidos fuel 5.8%. En los recién nacidos cuyas madres presentaron rotura de membranas de más de 18 horas, la colonización fue del 26.1%. Los recién nacidos colonizados (n=29), no presentaron diferencias con relación al resto de factores de riesgo: fiebre, bacteriuria materna, edad gestacional, peso y sexo del recién nacido. Conclusiones: si bien, la prevalencia ecncontrada de colonización por EGB en el recién nacido no fue tan alta como la reportada en otros países; sin embargo, se deben realizar otros estudios para establecer si ste agente es el responsable de infección en la etapa neonatal

Profilaxis antibiótica en la operación cesárea estudio comparativo entre ampicilina y ceftriaxona en profilaxis infecciosa postcesarea en el hospital Vicente Corral Moscoso

Se realiza un estudio en 90 pacientes intervenidas de cesárea no planificada en el hospital Vicente Corral Moscoso para determinar la eficacia profiláctica de los antibióticos en la prevención de la infección de los antibióticos en la prevención de la infección de la herida quirúrgica, de la endometritis y de la morbilidad febril, con la hipótesis de que es suficiente la administración de 3 dosis de ampicilina por vía venosa para prevenirlas: el grupo A recibió ampicilina, vía venosa en 3 dosis de 1 gramo con una hora de intervalo: el grupo B, ampicilina, en 21 dosis, una cada 8 horas, las primeras veinte y cuatro horas del postoperatorio via venosa y los seis días siguientes por vía oral, (esquema utilizado usualmente en el Hospital Vicente Corral Moscoso; y el grupo C ceftriaxona, vía venosa en 1 sola dosis de 1 gr. Los grupos de edstudio no presentaron entre ellos diferencias significativas en lo que se refiere a factores de riesgo: tiempo de labor de parto, dilatación cervical, rotura de membranas, tiempo de rotura de membranas, número de tactos y valores de hemoglobina. La infección de la herida se encontró en el 3.3de los casos no existiendo diferencia significativa entre los grupos de estudio (p>0.05). La endometritis fue del 1.1no observándose, igualmente, diferencia estadística entre los grupos de estudio. La morbilidad febril se presentó en el 15.6, igualmente sin diferencia significativa. Se concluye que no existe diferencia significativa en la administración antibiótica entre los tres grupos de estudio para prevenir la infección de la herida quirúrgica o la endometritis y estos valores concuerdan con los resultados que refieren la mayoría de estudios reportados en la literatura mundial

Reforma a seco de metano com catalisadores Ni/MCM-41 sintetizados a partir de fontes alternativas de sílica

The production of synthesis gas has received renewed attention due to demand for renewable energies to reduce the emissions of gases responsible for enhanced greenhouse effect. This work was carried out in order to synthesize, characterize and evaluate the implementation of nickel catalysts on MCM-41 in dry reforming reactions of methane. The mesoporous molecular sieves were synthesized using as silica sources the tetraethyl orthosilicate (TEOS) and residual glass powder (PV). The sieves were impregnated with 10% nickel to obtain the metallic catalysts (Ni/MCM-41). These materials were calcined and characterized by Thermogravimetric Analysis (TG), Infrared spectroscopy (FTIR), X-ray Diffraction (XRD), Temperature-Programmed Reduction (TPR) and N2 Adsorption/Desorption isotherms (BET/BJH). The catalytic properties of the samples were evaluated in methane dry reforming with CO2 in order to produce synthesis gas to be used in the petrochemical industry. The materials characterized showed hexagonal structure characteristic of mesoporous material MCM-41 type, being maintained after impregnation with nickel. The samples presented variations in the specific surface area, average volume and diameter of pores based on the type of interaction between the nickel and the mesoporous support. The result of the the catalytic tests showed conversions about 91% CO2, 86% CH4, yelds about 85% CO and 81% H2 to Ni/MCM-41_TEOS_C, and conversions about 87% CO2, 82% CH4, yelds about 70% CO and 59% H2 to Ni/MCM-41_PV_C. The similar performance confirms that the TEOS can be replaced by a less noble materials

Modelo Estocástico para bloqueio de poros e redução de permeabilidade

Modeling transport of particulate suspensions in porous media is essential for understanding various processes of industrial and scientific interest. During these processes, particles are retained due to mechanisms like size exclusion (straining), adsorption, sedimentation and diffusion. In this thesis, a mathematical model is proposed and analytical solutions are obtained. The obtained analytic solutions for the proposed model, which takes pore and particle size distributions into account, were applied to predict the particle retention, pore blocking and permeability reduction during dead-end microfiltration in membranes. Various scenarios, considering different particle and pore size distributions were studied. The obtained results showed that pore blocking and permeability reduction are highly influenced by the initial pore and particle size distributions. This feature was observed even when different initial pore and particle size distributions with the same average pore size and injected particle size were considered. Finally, a mathematical model for predicting equivalent permeability in porous media during particle retention (and pore blocking) is proposed and the obtained solutions were applied to study permeability decline in different scenarios

Avaliação histopatológica do fígado de bovinos mantidos em pastagens de Brachiaria spp. provenientes de abatedouros no Brasil

Dissertação (mestrado)—Universidade de Brasília, Faculdade de Agronomia e Medicina Veterinária, Programa de Pós-Graduação em Saúde Animal, 2016.

Structural and functional interaction between polyamine related molecules and biological membranes

Changes induced by PA on nucleic acid (NA) conformation and synthesis is proven to be a major reason for PA essentiality (1-3). However, PA interactions with other polyanions, for instance polyanionic membrane lipid bilayers and glyosaminoglycans have received less attention (3-4). The functional importance of these interactions still is an obscure but interesting area of cell and molecular biology, especially in mammalian cells for which specific PA transport systems are not fully characterized (5). In mammals, activity and turnover of the polyamine (PA) synthesis key enzyme is controlled by a set of proteins: Antizymes (OAZ1-3) and antizyme inhibitors (AZIN1 and 2). It is demonstrated that AOZ modulate polyamine uptake (6), and that PA transport to mitochondria is linked to the respiratory chain state and modulates mitochondrial permeability transition (7). Antizyme expression variants have been located in mitochondria, being proposed as a proapoptotic factor (7-8). AZIN 2 is only expressed in a reduced set of tissues that includes mast cells, where it is associated to mast cell granules membrane (9). This fact, together to the abnormalities observed in bone marrow derived mast cell granules when they are differentiated under restricted PA synthesis conditions (10 and unpublished results), point out to important roles of PA and their related proteins in structure and function of mast cell granules. We will also present novel biophysical results on tripartite interactions of PA that remark the interest of the characterization of PA interactions with lipid bilayers for biomedicine and biotechnology. Thus, the information reported in this paper integrates previously reported information with our still unpublished results, all indicating that PA and their related proteins also are important factors for structure and dynamics of biological membranes and their associated functions essential in human physiology; for instance, solute interchange with the environment (uptake and secretion), oxidative metabolism and apoptosis. The importance of these involved processes for human homeostasis claim for further research efforts. 1. Ruiz-Chica J, Medina MA, Sánchez-Jiménez F and Ramírez FJ (2001) Fourier Transform Raman study of the structural specificities on the interaction between DNA and biogenic polyamines. Biophysical J. 80:443-454. 2. Lightfoot HL, Hall J (2014) Endogenous polyamine function--the RNA perspective. Nucleic Acids Res. 42:11275-11290. 3. Igarashi K, Kashiwagi K (2010) Modulation of cellular function by polyamines. Int J Biochem Cell Biol. 42:39-51. 4. Finger S, Schwieger C, Arouri A, Kerth A, Blume A (2014) Interaction of linear polyamines with negatively charged phospholipids: the effect of polyamine charge distance. Biol Chem. 395:769-778. 5. Poulin R, Casero RA, Soulet D. (2012) Recent advances in the molecular biology of metazoan polyamine transport. Amino Acids. 42:711-723. 6. Kahana C (2009) Regulation of cellular polyamine levels and cellular proliferation by antizyme and antizyme inhibitor. Essays Biochem. 4:47-61. 7. Agostinelli E, Marques MP, Calheiros R, Gil FP, Tempera G, Viceconte N, Battaglia V, Grancara S, Toninello A (2010) Polyamines: fundamental characters in chemistry and biology. Amino Acids 38:393-403. 8. Liu GY, Liao YF, Hsu PC, Chang WH, Hsieh MC, Lin CY, Hour TC, Kao MC, Tsay GJ, Hung HC (2006) Antizyme, a natural ornithine decarboxylase inhibitor, induces apoptosis of haematopoietic cells through mitochondrial membrane depolarization and caspases' cascade. Apoptosis 11:1773-1788. 9. Kanerva K, Lappalainen J, Mäkitie LT, Virolainen S, Kovanen PT, Andersson LC (2009). Expression of antizyme inhibitor 2 in mast cells and role of polyamines as selective regulators of serotonin secretion. PLoS One 31:e6858. 10. García-Faroldi G, Rodríguez CE, Urdiales JL, Pérez-Pomares JM, Dávila JC, Pejler G, Sánchez-Jiménez F, Fajardo I (2010) Polyamines are present in mast cell secretory granules and are important for granule homeostasis. PLoS One 30:e15071.