Sustaining teacher professionalism in the context of standards referenced assessment reform

Standards referenced reform, tied to reporting, engages directly with assessment issues related to accountability. Assessment is the key to good education and is inseparable from curriculum. In an accountability context, standards are used as a lever to improve the reliability and consistency of teacher judgement; and classroom evidence is used by education systems for reporting and tracking achievement over time. Assessment is thus a powerful driver for change and is at the heart of the teaching-learning dynamic. The relationship between the learner, learning and assessment needs to be kept central and the idea of teacher empowerment is fundamental. This chapter is a call to honour and sustain teacher professionalism through educative forms of school-based and teacher-led evaluation, assessment and communities of judgement practice. It supports the argument for a central place for classroom assessment in the role of assessment in educational accountability...

Concentration and oxidative potential of on-road particle emissions and their relationship with traffic composition : Relevance to exposure assessment

Particles emitted by vehicles are known to cause detrimental health effects, with their size and oxidative potential among the main factors responsible. Therefore, understanding the relationship between traffic composition and both the physical characteristics and oxidative potential of particles is critical. To contribute to the limited knowledge base in this area, we investigated this relationship in a 4.5 km road tunnel in Brisbane, Australia. On-road concentrations of ultrafine particles (<100 nm, UFPs), fine particles (PM2.5), CO, CO2 and particle associated reactive oxygen species (ROS) were measured using vehicle-based mobile sampling. UFPs were measured using a condensation particle counter and PM2.5 with a DustTrak aerosol photometer. A new profluorescent nitroxide probe, BPEAnit, was used to determine ROS levels. Comparative measurements were also performed on an above-ground road to assess the role of emission dilution on the parameters measured. The profile of UFP and PM2.5 concentration with distance through the tunnel was determined, and demonstrated relationships with both road gradient and tunnel ventilation. ROS levels in the tunnel were found to be high compared to an open road with similar traffic characteristics, which was attributed to the substantial difference in estimated emission dilution ratios on the two roadways. Principal component analysis (PCA) revealed that the levels of pollutants and ROS were generally better correlated with total traffic count, rather than the traffic composition (i.e. diesel and gasoline-powered vehicles). A possible reason for the lack of correlation with HDV, which has previously been shown to be strongly associated with UFPs especially, was the low absolute numbers encountered during the sampling. This may have made their contribution to in-tunnel pollution largely indistinguishable from the total vehicle volume. For ROS, the stronger association observed with HDV and gasoline vehicles when combined (total traffic count) compared to when considered individually may signal a role for the interaction of their emissions as a determinant of on-road ROS in this pilot study. If further validated, this should not be overlooked in studies of on- or near-road particle exposure and its potential health effects.

The assessment of mental health in children with intellectual disability

Aim: Individuals with intellectual disability (ID) have higher rates of mental health problems than the general population. Assessment tends to rely heavily on self-report, but persons with ID often have difficulties in identifying and describing their own thoughts and feelings. Measures that are psychometrically sound with typically developing populations may not be as robust in samples with ID. The aim of the current study was to examine a range of self-report measures for assessing the mental health of children with ID, and to consider the appropriateness of minor modifications to those instruments. Method: The participants were 58 children with ID (mean 11.7 years) attending Year 6 in mainstream primary schools. At the first time point they completed four established measures of depression, anxiety and mood. Minor modifications were made to wording and format at re-administration six months later. Results: Internal consistency varied considerably across measures. Modifications resulted in small or no improvements, but the results were relatively consistent over time and across similar measures. Some gender differences were evident. Conclusions: The findings confirm the difficulties that children with ID may have when responding to self-report measures of mental health, and suggest that care should be taken in choice of instruments. While modifications can produce small improvements, it is clear that more robust measures of mental health are needed for persons with ID.

Towards local cultures of sustainability : facilitating community created environment education centres through design

Ecological sustainability has been proposed to address the problem of human impacts increasingly degrading planetary resources and ecosystems, threatening biodiversity, eco-services and human survival. Ecological sustainability is an imperative, with Australia having one of the highest eco-footprints per person worldwide. While significant progress has been made via implementation of ecologically sustainable design in urban communities, relatively little has been undertaken in small, disparate regional communities in Australia. Regional communities are disadvantaged by rural economic decline associated with structural change and inequities of resource transfer. The ecologically sustainable solution is holistic, so all settlements need to be globally wise, richly biodiverse yet locally specific. As a regional solution to this global problem, this research offers the practical means by which a small regional community can contribute. It focuses on the design and implementation of a community centre and the fostering of transformative community learning through an integrated ‘learning community’ awareness of ecologically sustainable best practice. Lessons learned are documented by the participant researcher who as a designer, facilitator, local resident and social narrator has been deeply connected with the Tweed-Caldera region over a period since 1980. The collective action of the local community of Chillingham has been diligently recorded over a decade of design and development. Over this period, several positive elements emerged in terms of improvements to the natural and built environment, greater social cohesion and co-operative learning along with a shift towards a greener local economy. Behavioural changes in the community were noted as residents strived to embrace ecological ideals and reduce fossil fuel dependency. They found attractive local solutions to sourcing of food and using local employment opportunities to up skill their residents via transformative learning as a community in transition. Finally, the catalytic impact of external partnering has also been documented. How well the region as a whole has achieved its ecologically sustainable objectives is measured in terms of the delivered success of private and public partnering with the community, the creation of a community centre cum environment education centre, the restoration of local heritage buildings, the repair of riparian forests and improved water conditions in local river systems, better roads and road safety, local skills and knowledge transfer, support of local food and local/regional growers markets to attract tourists via the integrated trails network. In aggregate, each and every element contributes to a measure of eco-positive development for the built environment, its social organisation and its economy that has guided the local community to find its own pathway to sustainability. Within the Tweed-Caldera bioregion in northern New South Wales, there has been a lack of strategic planning, ecologically sustainable knowledge and facilities in isolated communities that could support the development of a local sustained green economy, provide a hub for socio-cultural activities and ecology based education. The first challenge in this research was to model a whole systems approach to eco-positive development in Chillingham, NSW, a small community where Nature and humanity know no specific boundary. The net result was the creation of a community environment education centre featuring best-affordable ecological practice and regionally distinctive, educational building form from a disused heritage building (cow bale). This development, implemented over a decade, resonated with the later regional wide programs that were linked in the Caldera region by the common purpose of extending the reach of local and state government assistance to regional NSW in economic transition coupled with sustainability. The lessons learned from these linked projects reveal that subsequent programs have been significantly easier to initiate, manage, develop and deliver results. In particular, pursuing collaborative networks with all levels of government and external private partners has been economically effective. Each community’s uniqueness has been celebrated and through drawing out these distinctions, has highlighted local vision, strategic planning, sense of belonging and connection of people with place. This step has significantly reduced the level of friction between communities that comes from natural competition for the finite pool of funds. Following the pilot Tweed-Caldera study, several other NSW regional communities are now undertaking a Community Economic Transition Program based on the processes, trials and positive experiences witnessed in the Tweed-Caldera region where it has been demonstrated that regional community transition programs can provide an opportunity to plan and implement effective long term strategies for sustainability, empowering communities to participate in eco-governance. This thesis includes the design and development of a framework for community created environment education centres to provide an equal access place for community to participate to meet their essential needs locally. An environment centre that facilitates community transition based on easily accessible environmental education, skills and infrastructure is necessary to develop local cultures of sustainability. This research draws upon the literatures of ecologically sustainable development, environmental education and community development in the context of regional community transition towards ‘strong sustainability’. The research approach adapted is best described as a four stage collaborative action research cycle where the participant researcher (me) has a significant involvement in the process to foster local cultures of sustainability by empowering its citizens to act locally and in doing so, become more self reliant and socially resilient. This research also draws upon the many fine working exemplars, such as the resilience of the Cuban people, the transition town initiative in Totnes, U.K. and the models of Australian Community Gardens, such as CERES (Melbourne) and Northey Street (Brisbane). The objectives of this study are to research and evaluate exemplars of ecologically sustainable environment education centres, to facilitate the design and development of an environment education centre created by a small regional community as an ecologically sustainable learning environment; to facilitate a framework for community transition based on environmental education, skills and infrastructure necessary to develop local cultures of sustainability. The research was undertaken as action research in the Tweed Caldera in Northern NSW. This involved the author as participant researcher, designer and volunteer in two interconnected initiatives: the Chillingham Community Centre development and the Caldera Economic Transition Program (CETP). Both initiatives involved a series of design-led participatory community workshops that were externally facilitated with the support of government agency partnerships, steering committees and local volunteers. Together the Caldera research programs involved communities participating in developing their own strategic planning process and outcomes. The Chillingham Community Centre was developed as a sustainable community centre/hub using a participatory design process. The Caldera Economic Transition Program (CETP) prioritised Caldera region projects: the Caldera farmer’s market; community gardens and community kitchens; community renewable energy systems and an integrated trails network. The significant findings were: the CETP projects were capable of moving towards an eco-positive design benchmark through transformative learning. Community transition to sustainability programs need to be underpinned by sustainability and environmental education based frameworks and practical on ground experience in local needs based projects through transformative learning. The actioned projects were successfully undertaken through community participation and teamwork. Ecological footprint surveys were undertaken to guide and assess the ongoing community transition process, however the paucity of responses needs to be revisited. The concept of ecologically sustainable development has been adopted internationally, however existing design and planning strategies do not assure future generations continued access to healthy natural life support systems. Sustainable design research has usually been urban focussed, with little attention paid to regional communities. This study seeks to redress this paucity through the design of ecologically sustainable (deep green) learning environments for small regional communities. Through a design-led process of environmental education, this study investigates how regional communities can be facilitated to model the principles of eco-positive development to support transition to local cultures of sustainability. This research shows how community transition processes and projects can incorporate sustainable community development as transformative learning through design. Regional community transition programs can provide an opportunity to plan long term strategies for sustainability, empowering people to participate in eco-governance. A framework is developed for a community created environment education centre to provide an equal access place for the local community to participate in implementing ways to meet their essential needs locally. A community environment education centre that facilitates community transition based on holistic environmental education, skills and infrastructure is necessary to develop local cultures of sustainability.

Malnutrition screening tools : comparison against two validated nutrition assessment methods in older medical inpatients

Objective Although several validated nutritional screening tools have been developed to “triage” inpatients for malnutrition diagnosis and intervention, there continues to be debate in the literature as to which tool/tools clinicians should use in practice. This study compared the accuracy of seven validated screening tools in older medical inpatients against two validated nutritional assessment methods. Methods This was a prospective cohort study of medical inpatients at least 65 y old. Malnutrition screening was conducted using seven tools recommended in evidence-based guidelines. Nutritional status was assessed by an accredited practicing dietitian using the Subjective Global Assessment (SGA) and the Mini-Nutritional Assessment (MNA). Energy intake was observed on a single day during first week of hospitalization. Results In this sample of 134 participants (80 ± 8 y old, 50% women), there was fair agreement between the SGA and MNA (κ = 0.53), with MNA identifying more “at-risk” patients and the SGA better identifying existing malnutrition. Most tools were accurate in identifying patients with malnutrition as determined by the SGA, in particular the Malnutrition Screening Tool and the Nutritional Risk Screening 2002. The MNA Short Form was most accurate at identifying nutritional risk according to the MNA. No tool accurately predicted patients with inadequate energy intake in the hospital. Conclusion Because all tools generally performed well, clinicians should consider choosing a screening tool that best aligns with their chosen nutritional assessment and is easiest to implement in practice. This study confirmed the importance of rescreening and monitoring food intake to allow the early identification and prevention of nutritional decline in patients with a poor intake during hospitalization.

Assessment of “change in flexibility method” in structural health monitoring systems

The modern structural diagnosis process is rely on vibration characteristics to assess safer serviceability level of the structure. This paper examines the potential of change in flexibility method to use in damage detection process and two main practical constraints associated with it. The first constraint addressed in this paper is reduction in number of data acquisition points due to limited number of sensors. Results conclude that accuracy of the change in flexibility method is influenced by the number of data acquisition points/sensor locations in real structures. Secondly, the effect of higher modes on damage detection process has been studied. This addresses the difficulty of extracting higher order modal data with available sensors. Four damage indices have been presented to identify their potential of damage detection with respect to different locations and severity of damage. A simply supported beam with two degrees of freedom at each node is considered only for a single damage cases throughout the paper.

Not all older adults have insight into their driving abilities : evidence from an on-road assessment and implications for policy

Purpose To compare self-reported driving ability with objective measures of on-road driving performance in a large cohort of older drivers. Methods 270 community-living adults aged 70 – 88 years recruited via the electoral roll completed a standardized assessment of on-road driving performance and questionnaires determining perceptions of their own driving ability, confidence and driving difficulties. Retrospective self-reported crash data over the previous five years were recorded. Results Participants reported difficulty with only selected driving situations, including driving into the sun, in unfamiliar areas, in wet conditions, and at night or dusk. The majority of participants rated their own driving as good to excellent. Of the 47 (17%) of drivers who were rated as potentially unsafe to drive, 66% rated their own driving as good to excellent. Drivers who made critical errors, where the driving instructor had to take control of the vehicle, had no lower self-rating of driving ability then the rest of the group. The discrepancy in self-perceptions of driving and participants’ safety rating on the on-road assessment was significantly associated with self-reported retrospective crash rates, where those drivers who displayed greater overconfidence in their own driving were significantly more likely to report a crash. Conclusions This study demonstrates that older drivers with the greatest mismatch between actual and self-rated driving ability pose the greatest risk to road safety. Therefore licensing authorities should not assume that when older individuals’ driving abilities begin to decline they will necessarily be aware of these changes and adopt appropriate compensatory driving behaviours; rather, it is essential that evidence-based assessments are adopted.

Assessment of flood-related recharge to alluvial aquifers of an irrigated catchment following extended drought conditions using 3D visualisation and environmental tracers, Lockyer Valley, southeast Queensland, Australia.

The Lockyer Valley in southeast Queensland, Australia, hosts an economically significant alluvial aquifer system which has been impacted by prolonged drought conditions (~1997 to ~ 2009). Throughout this time, the system was under continued groundwater extraction, resulting in severe aquifer depletion. By 2008, much of the aquifer was at <30% of storage but some relief occurred with rains in early 2009. However, between December 2010 and January 2011, most of southeast Queensland experienced unprecedented flooding, which generated significant aquifer recharge. In order to understand the spatial and temporal controls of groundwater recharge in the alluvium, a detailed 3D lithological property model of gravels, sands and clays was developed using GOCAD software. The spatial distribution of recharge throughout the catchment was assessed using hydrograph data from about 400 groundwater observation wells screened at the base of the alluvium. Water levels from these bores were integrated into a catchment-wide 3D geological model using the 3D geological modelling software GOCAD; the model highlights the complexity of recharge mechanisms. To support this analysis, groundwater tracers (e.g. major and minor ions, stable isotopes, 3H and 14C) were used as independent verification. The use of these complementary methods has allowed the identification of zones where alluvial recharge primarily occurs from stream water during episodic flood events. However, the study also demonstrates that in some sections of the alluvium, rainfall recharge and discharge from the underlying basement into the alluvium are the primary recharge mechanisms of the alluvium. This is indicated by the absence of any response to the flood, as well as the observed old radiocarbon ages and distinct basement water chemistry signatures at these locations. Within the 3D geological model, integration of water chemistry and time-series displays of water level surfaces before and after the flood suggests that the spatial variations of the flood response in the alluvium are primarily controlled by the valley morphology and lithological variations within the alluvium. The integration of time-series of groundwater level surfaces in the 3D geological model also enables the quantification of the volumetric change of groundwater stored in the unconfined sections of this alluvial aquifer during drought and following flood events. The 3D representation and analysis of hydraulic and recharge information has considerable advantages over the traditional 2D approach. For example, while many studies focus on singular aspects of catchment dynamics and groundwater-surface water interactions, the 3D approach is capable of integrating multiple types of information (topography, geological, hydraulic, water chemistry and spatial) into a single representation which provides valuable insights into the major factors controlling aquifer processes.

Assessment of interactions between alluvial, Great Artesian Basin (GAB) and volcanic aquifers using 3D visualisation and environmental tracers, Lockyer Valley, southeast Queensland, Australia

A detailed 3D lithological model framework was developed using GOCAD software to understand interactions between alluvial, volcanic and GAB aquifers and the spatial and temporal distribution of groundwater recharge to the alluvium of the Lockyer Valley. Groundwater chemistry, isotope data (H20-δ2H and δ18O , 87Sr/86Sr, 3H and 14C) and groundwater level time-series data from approximately 550 observation wells were integrated into the catchment-wide 3D model to assess the recharge processes involved. This approach enabled the identification of zones where recharge to the alluvium primarily occurs from stream water during episodic flood events. Importantly, the study also demonstrates that in some sections of the alluvium recharge is also from storm rainfall and seepage discharge from the underlying GAB aquifers. These other sources of recharge are indicated by (a) the absence of a response of groundwater levels to flooding in some areas, (b) old radiocarbon ages, and (c) distinct bedrock water chemistry and δ2H and δ18O signatures in alluvial groundwater at these locations. Integration of isotopes, water chemistry and time-series displays of groundwater levels before and after the 2010/2011 flood into the 3D model suggest that the spatial variations in the alluvial groundwater response are mostly controlled by valley morphology and lithological (i.e. permeability) variations within the alluvium. Examination of the groundwater level variations in the 3D model also enabled quantification of the volumetric change of groundwater stored in the unconfined alluvial aquifer prior to and post-flood events.

Their space, my space, our space? Report of the 2009 Redland City Council Youth and Public Space Survey

This report analyses data collected through the Redland City Council’s Young People and Public Space Survey of 2148 high school students aged 12-19. The survey conducted in 2009 explored their sense of safety and experiences in public spaces across the City, and views on what Council could do to improve these. It is apparent they base their assessment of a space as ‘public’ on their ‘use’ of a space alone or with friends, and where strangers may be present, rather than on a type of ownership of a space (public/ private). The findings of the survey are summarised according to the themes of safety, community attitudes towards young people being in public spaces, young people and authorities, young people’s views of what is needed, and understanding different young people’s experiences of public space.

Nonprofit organisations face a restructuring state : the case of local social services in the Hunter region of New South Wales

This paper is concerned with certain of the characteristics of local social services, and their role in a restructuring Australian welfare state. I am particularly concerned with the distinctive gender characteristics of these organisations, because in comparison with most other organisations they have a feminised quality. This partly mirrors women's traditional role of undertaking the major part of the caring labour of society. However, simultaneously work in these organisation deviates from more traditional patterns where employed women occupy subordinate positions. In many community organisations, women occupy leadership roles. The analysis here is concerned with the apparently paradoxical nature of these organisations in their capacity to entrench traditional gender roles and to challenge these by allowing women to fill management positions. It is also concerned to examine whether changes that have been occurring in the community services sector over the last two decades are likely to enhance women's general position in the society, or diminish the power exercised by women. The paper draws in a preliminary way on a study of local services in the Hunter Region of NSW undertaken in the latter half of 1992. These preliminary findings are set against the broader picture of developments in the contemporary welfare state.

Innovative damage assessment of steel truss bridges using modal strain energy correlation

As a part of vital infrastructure and transportation network, bridge structures must function safely at all times. Bridges are designed to have a long life span. At any point in time, however, some bridges are aged. The ageing of bridge structures, given the rapidly growing demand of heavy and fast inter-city passages and continuous increase of freight transportation, would require diligence on bridge owners to ensure that the infrastructure is healthy at reasonable cost. In recent decades, a new technique, structural health monitoring (SHM), has emerged to meet this challenge. In this new engineering discipline, structural modal identification and damage detection have formed a vital component. Witnessed by an increasing number of publications is that the change in vibration characteristics is widely and deeply investigated to assess structural damage. Although a number of publications have addressed the feasibility of various methods through experimental verifications, few of them have focused on steel truss bridges. Finding a feasible vibration-based damage indicator for steel truss bridges and solving the difficulties in practical modal identification to support damage detection motivated this research project. This research was to derive an innovative method to assess structural damage in steel truss bridges. First, it proposed a new damage indicator that relies on optimising the correlation between theoretical and measured modal strain energy. The optimisation is powered by a newly proposed multilayer genetic algorithm. In addition, a selection criterion for damage-sensitive modes has been studied to achieve more efficient and accurate damage detection results. Second, in order to support the proposed damage indicator, the research studied the applications of two state-of-the-art modal identification techniques by considering some practical difficulties: the limited instrumentation, the influence of environmental noise, the difficulties in finite element model updating, and the data selection problem in the output-only modal identification methods. The numerical (by a planer truss model) and experimental (by a laboratory through truss bridge) verifications have proved the effectiveness and feasibility of the proposed damage detection scheme. The modal strain energy-based indicator was found to be sensitive to the damage in steel truss bridges with incomplete measurement. It has shown the damage indicator's potential in practical applications of steel truss bridges. Lastly, the achievement and limitation of this study, and lessons learnt from the modal analysis have been summarised.

Analysis of acoustic emission data for accurate damage assessment for structural health monitoring applications

Structural health monitoring (SHM) refers to the procedure used to assess the condition of structures so that their performance can be monitored and any damage can be detected early. Early detection of damage and appropriate retrofitting will aid in preventing failure of the structure and save money spent on maintenance or replacement and ensure the structure operates safely and efficiently during its whole intended life. Though visual inspection and other techniques such as vibration based ones are available for SHM of structures such as bridges, the use of acoustic emission (AE) technique is an attractive option and is increasing in use. AE waves are high frequency stress waves generated by rapid release of energy from localised sources within a material, such as crack initiation and growth. AE technique involves recording these waves by means of sensors attached on the surface and then analysing the signals to extract information about the nature of the source. High sensitivity to crack growth, ability to locate source, passive nature (no need to supply energy from outside, but energy from damage source itself is utilised) and possibility to perform real time monitoring (detecting crack as it occurs or grows) are some of the attractive features of AE technique. In spite of these advantages, challenges still exist in using AE technique for monitoring applications, especially in the area of analysis of recorded AE data, as large volumes of data are usually generated during monitoring. The need for effective data analysis can be linked with three main aims of monitoring: (a) accurately locating the source of damage; (b) identifying and discriminating signals from different sources of acoustic emission and (c) quantifying the level of damage of AE source for severity assessment. In AE technique, the location of the emission source is usually calculated using the times of arrival and velocities of the AE signals recorded by a number of sensors. But complications arise as AE waves can travel in a structure in a number of different modes that have different velocities and frequencies. Hence, to accurately locate a source it is necessary to identify the modes recorded by the sensors. This study has proposed and tested the use of time-frequency analysis tools such as short time Fourier transform to identify the modes and the use of the velocities of these modes to achieve very accurate results. Further, this study has explored the possibility of reducing the number of sensors needed for data capture by using the velocities of modes captured by a single sensor for source localization. A major problem in practical use of AE technique is the presence of sources of AE other than crack related, such as rubbing and impacts between different components of a structure. These spurious AE signals often mask the signals from the crack activity; hence discrimination of signals to identify the sources is very important. This work developed a model that uses different signal processing tools such as cross-correlation, magnitude squared coherence and energy distribution in different frequency bands as well as modal analysis (comparing amplitudes of identified modes) for accurately differentiating signals from different simulated AE sources. Quantification tools to assess the severity of the damage sources are highly desirable in practical applications. Though different damage quantification methods have been proposed in AE technique, not all have achieved universal approval or have been approved as suitable for all situations. The b-value analysis, which involves the study of distribution of amplitudes of AE signals, and its modified form (known as improved b-value analysis), was investigated for suitability for damage quantification purposes in ductile materials such as steel. This was found to give encouraging results for analysis of data from laboratory, thereby extending the possibility of its use for real life structures. By addressing these primary issues, it is believed that this thesis has helped improve the effectiveness of AE technique for structural health monitoring of civil infrastructures such as bridges.

A survey to evaluate the implementation of a national clinical assessment form

Purpose: The Australian Universities Radiation Therapy Student Clinical Assessment Form (AURTSCAF) was designed to assess the clinical skills of radiation therapy (RT) students from the six universities that offer entry level RT programs. Given the AURTSCAF has now been in use for over two years, the Radiation Therapy Program Coordinators (RTPC) group initiated a post implementation evaluation survey. This formed the final phase of the AURTSCAF project and was funded by the Radiation Oncology Division of the Department of Health and Ageing. Methods: A cross-sectional designed survey using purposive sampling was distributed via email to all RT clinical sites. The survey asked questions about the requirements of a pass grade for students at different stages of their program, and the addition of a new category of assessment related to fitness to practise. Response types included both forced choice closed ended responses and open ended responses. There was also a section for open comments about the AURTSCAF. Results: There were 100 responses (55%) from clinicians who had utilised the assessment form over the previous 12 month period. Responses highlighted several positives with regard to the utility and implementation of the form. Comments regarding areas for improvement with the standardisation of the grading of students and consensus for the addition of a new domain in fitness for practise have informed the recommended changes proposed for 2012. Conclusion: This evaluation has provided a representative sample of the views of clinicians involved in assessing students on clinical placement. Recommendations include the addition of the sixth domain of assessment: Fitness for practise, the addition of descriptors and prompts for this domain in the user guide, the addition of a consensus statement about the use of the rating scale and dissemination of the proposed changes nationally.

Global flash multifocal electroretinogram : early detection of local functional changes and its correlations with optical coherence tomography and visual field loss in diabetic eyes

Purpose: To investigate the correlations of the global flash multifocal electroretinogram (MOFO mfERG) with common clinical visual assessments – Humphrey perimetry and Stratus circumpapillary retinal nerve fiber layer (RNFL) thickness measurement in type II diabetic patients. Methods: Forty-two diabetic patients participated in the study: ten were free from diabetic retinopathy (DR) while the remainder suffered from mild to moderate non-proliferative diabetic retinopathy (NPDR). Fourteen age-matched controls were recruited for comparison. MOFO mfERG measurements were made under high and low contrast conditions. Humphrey central 30-2 perimetry and Stratus OCT circumpapillary RNFL thickness measurements were also performed. Correlations between local values of implicit time and amplitude of the mfERG components (direct component (DC) and induced component (IC)), and perimetric sensitivity and RNFL thickness were evaluated by mapping the localized responses for the three subject groups. Results: MOFO mfERG was superior to perimetry and RNFL assessments in showing differences between the diabetic groups (with and without DR) and the controls. All the MOFO mfERG amplitudes (except IC amplitude at high contrast) correlated better with perimetry findings (Pearson’s r ranged from 0.23 to 0.36, p<0.01) than did the mfERG implicit time at both high and low contrasts across all subject groups. No consistent correlation was found between the mfERG and RNFL assessments for any group or contrast conditions. The responses of the local MOFO mfERG correlated with local perimetric sensitivity but not with RNFL thickness. Conclusion: Early functional changes in the diabetic retina seem to occur before morphological changes in the RNFL.