Assessment of the VoIP Transmission Quality over Digital Power Line Carrier Channels

This article is devoted to the research of VoIP transmission quality over Digital Power Line Carrier channels. Assessment of quality transmission is performed using E-model. Paper considers the possibility of joint using of Digital Power Line carrier equipment with different architecture in one network. As a result of the research, the rule for constructing of multi-segment Digital Power Line Carrier channels was formulated. This rule allows minimizing the transmission delay and saving frequency resources of high voltage Power Line Carrier range.

The Research of Increase of Channel Efficiency for IP Traffic Transmission over Digital Power Line Carrier Channels

This article is devoted to the research of channel efficiency for IP-traffic transmission over Digital Power Line Carrier channels. The application of serial WAN connections and header compression as methods to increase channel efficiency is considered. According to the results of the research an effective solution for network traffic transmission in DPLC networks was proposed.

When the Line is Crossed... : Paths to Control and Sanction Behaviour Necessitating a State Reaction

The article presents a special form of a European comparative synopsis. For this case examples have been chosen ranging from administrative or minor (criminal) offences to increasingly serious offences and offenders. In this way it can be comparatively demonstrated how the criminal justice systems studied handle specific cases and whether they do so in a similar or different way.

Y-90-Ibritumomab Tiuxetan (Zevalin (R)) Consolidation of First Remission In Advanced-Stage Follicular Non-Hodgkin's Lymphoma: Updated Results After a Median Follow-up of 66.2 Months From the International, Randomized, Phase III First-Line Indolent Trial (FIT) In 414 Patients

The FIT trial was conducted to evaluate the safety and efficacy of 90Y-ibritumomab tiuxetan (0.4 mCi/kg; maximum dose 32 mCi) when used as consolidation of first complete or partial remission in patients with previously untreated, advanced-stage follicular lymphoma (FL). Patients were randomly assigned to either 90Y-ibritumomab treatment (n = 207) or observation (n = 202) within 3 months (mo) of completing initial induction therapy (chemotherapy only: 86%; rituximab in combination with chemotherapy: 14%). Response status prior to randomization did not differ between the groups: 52% complete response (CR)/CR unconfirmed (CRu) to induction therapy and 48% partial response (PR) in the 90Y-ibritumomab arm vs 53% CR/CRu and 44% PR in the control arm. The primary endpoint was progression-free survival (PFS) of the intent-to-treat (ITT) population. Results from the first extended follow-up after a median of 3.5 years revealed a significant improvement in PFS from the time of randomization with 90Y-ibritumomab consolidation compared with control (36.5 vs 13.3 mo, respectively; P < 0.0001; Morschhauser et al. JCO. 2008; 26:5156-5164). Here we report a median follow-up of 66.2 mo (5.5 years). Five-year PFS was 47% in the 90Y-ibritumomab group and 29% in the control group (hazard ratio (HR) = 0.51, 95% CI 0.39-0.65; P < 0.0001). Median PFS in the 90Y-ibritumomab group was 49 mo vs 14 mo in the control group. In patients achieving a CR/CRu after induction, 5-year PFS was 57% in the 90Y-ibritumomab group, and the median had not yet been reached at 92 months, compared with a 43% 5-year PFS in the control group and a median of 31 mo (HR = 0.61, 95% CI 0.42-0.89). For patients in PR after induction, the 5-year PFS was 38% in the 90Y-ibritumomab group with a median PFS of 30 mo vs 14% in the control group with a median PFS of 6 mo (HR = 0.38, 95% CI 0.27-0.53). Patients who had received rituximab as part of induction treatment had a 5-year PFS of 64% in the 90Y-ibritumomab group and 48% in the control group (HR = 0.66, 95% CI 0.30-1.47). For all patients, time to next treatment (as calculated from the date of randomization) differed significantly between both groups; median not reached at 99 mo in the 90Y-ibritumomab group vs 35 mo in the control group (P < 0.0001). The majority of patients received rituximab-containing regimens when treated after progression (63/82 [77%] in the 90Y-ibritumomab group and 102/122 [84%] in the control group). Overall response rate to second-line treatment was 79% in the 90Y-ibritumomab group (57% CR/CRu and 22% PR) vs 78% in the control arm (59% CR/CRu, 19% PR). Five-year overall survival was not significantly different between the groups; 93% and 89% in the 90Y-ibritumomab and control groups, respectively (P = 0.561). To date, 40 patients have died; 18 in the 90Y-ibritumomab group and 22 in the control group. Secondary malignancies were diagnosed in 16 patients in the 90Y-ibritumomab arm vs 9 patients in the control arm (P = 0.19). There were 6 (3%) cases of myelodysplastic syndrome (MDS)/acute myelogenous leukemia (AML) in the 90Y-ibritumomab arm vs 1 MDS in the control arm (P = 0.063). In conclusion, this extended follow-up of the FIT trial confirms the benefit of 90Y-ibritumomab consolidation with a nearly 3 year advantage in median PFS. A significant 5-year PFS improvement was confirmed for patients with a CR/CRu or a PR after induction. Effective rescue treatment with rituximab-containing regimens may explain the observed no difference in overall survival between both patient groups who were - for the greater part - rituximab-naïve.

Pesca experimental con palangre o long-line a bordo de una lancha anchovetera

Presentan los resultados, la metodología de pesca adoptada y algunas observaciones bio-oceanográficas. Asi como la técnica de pesca utilizando, el comportamiento y eficiencia del palanque o long line en relación a la temperatura - profundidad que alcanzan los anzuelos y su captura por especies, el tipo de carnada y su porcentaje de utilización; así mismo, la adaptación realizada a bordo para facilidad de maniobras con el aparejo y algunas observaciones bio oceanográficas.

Direct-on-line axial flux permanent magnet synchronous generator static and dynamic performance

In distributed energy production, permanent magnet synchronous generators (PMSG) are often connected to the grid via frequency converters, such as voltage source line converters. The price of the converter may constitute a large part of the costs of a generating set. Some of the permanent magnet synchronous generators with converters and traditional separately excited synchronous generators couldbe replaced by direct-on-line (DOL) non-controlled PMSGs. Small directly networkconnected generators are likely to have large markets in the area of distributed electric energy generation. Typical prime movers could be windmills, watermills and internal combustion engines. DOL PMSGs could also be applied in island networks, such as ships and oil platforms. Also various back-up power generating systems could be carried out with DOL PMSGs. The benefits would be a lower priceof the generating set and the robustness and easy use of the system. The performance of DOL PMSGs is analyzed. The electricity distribution companies have regulations that constrain the design of the generators being connected to the grid. The general guidelines and recommendations are applied in the analysis. By analyzing the results produced by the simulation model for the permanent magnet machine, the guidelines for efficient damper winding parameters for DOL PMSGs are presented. The simulation model is used to simulate grid connections and load transients. The damper winding parameters are calculated by the finite element method (FEM) and determined from experimental measurements. Three-dimensional finite element analysis (3D FEA) is carried out. The results from the simulation model and 3D FEA are compared with practical measurements from two prototype axial flux permanent magnet generators provided with damper windings. The dimensioning of the damper winding parameters is case specific. The damper winding should be dimensioned based on the moment of inertia of the generating set. It is shown that the damper winding has optimal values to reach synchronous operation in the shortest period of time after transient operation. With optimal dimensioning, interferenceon the grid is minimized.

Biopolttoaineiden on-line -laadunmittauksen hyödyt energiantuotannossa

Biopolttoaineet ovat tärkeä energianlähde suomalaisessa energiantuotannossa. Biopoltto- aineille on kuitenkin ominaista laadun vaihtelevuus. Yksi tärkeimmistä laatutekijöistä on kosteus, joka vaikuttaa myös polttoaineen energiasisältöön. Laatutekijät puolestaan vai- kuttavat polttoainekäsittelyyn, polttoprosessiin ja koko laitoksen hyötysuhteeseen. Tämän työn tarkoituksena oli tutkia voisiko biopolttoaineiden online-laadunmittaus tuoda lisäarvoa energiantuotantolaitokselle. Esimerkkinä käytettiin yhtä online-laadunmittaus- sovellusta, InrayFuel-röntgenmittausjärjestelmää. Sillä voidaan seurata biopolttoaineiden kosteutta ja polttoaineen sisältämiä vierasaineita. Työssä on laadittu kustannusanalyysi, jolla pyritään selvittämään, onko nykyisen kertaluontoisen mittausmenetelmän korvaami- nen jatkuvatoimisella kannattavaa. Esimerkkilaitoksena on Etelä-Savon Energian Pur- sialan voimalaitos, jossa röntgenmittausjärjestelmään on testattu. Saatujen tulosten mukaan investoiminen esimerkkimittausjärjestelmään maksaisi itsensä takaisin alle vuodessa. Kun laitoksella pystytään seuraamaan polttoaineen laatua jatkuva- toimisesti, laadunhallinta paranee ja sitä kautta voidaan saavuttaa kustannussäästöjä. Polt- toaineesta johtuvat häiriötilanteet vähenevät, polttoaine on mahdollista optimoida edulli- semmaksi polton kannalta ja poltto-olosuhteita voidaan säätää paremmin, jolloin päästöt vähenevät ja hyötysuhde kasvaa. Työssä käytetty laskenta analysoi kuitenkin hyvin ylei- sellä tasolla, sillä käytössä ei ollut laitoksen omaa taselaskentajärjestelmää. Laskenta siis sisältää paljon oletuksia. Tämän ja rohkaisevien tulosten vuoksi tutkimusta jatkuvatoimi- sen laadunmittauksen hyödyistä kannattaa tehdä enemmän.

Software product line for power converters

Työn tilaajana toimi Visedo Oy. Työn tavoitteina oli tutkia Visedo Oy:n ohjelmistokehityksen nykytila, tunnistaa seuraavat parannuskohteet ja antaa ohjeita havaittujen parannuskohteiden korjaamiseksi. Visedo Oy:n tehonmuokkain ohjelmistokehityksen nykytilaa käsiteltiin neljän valitun osa-alueen näkökulmasta: ohjelmistoarkkitehtuurityyli, komponenttipohjainen ohjelmistokehitys, ohjelmistotuotelinjojen kehitysmenetelmät ja ohjelmistovariaatioiden hallinta. Valituilla osa-alueilla havaittujen parannuskohteiden perusteella annettiin korjausehdotuksia: ohjelmistoarkkitehtuurin rakenteeseen, komponenttien jakautumiselle, komponenttien koostamiselle ja komponenttien versioinnille. Lisäksi ehdotettiin uudenlaista ohjelmistotuotelinja rakennetta, joka yhdistää kerros- ja komponenttipohjaiset arkkitehtuurityylit mahdollistaen ominaisuuksiltaan eroavien tehonmuokkain ohjelmistojen hallinnan.

The same old line?

As long as you've got metal zippers in your garments you're selling an old line. Today's fashions are much more demanding. They need what a Lightning Zephyr can give them. Part of the tag line for an ad aimed at the garment industry.

Arsenic speciation by ion-exchange chromatography with on- line determination by hydride generation: electronic modification of the D.C. plasma by photon counting

A method using L-cysteine for the determination of arsenous acid (As(III)), arsenic acid (As(V)), monomethylarsonic acid (MMAA), and dimethylarsinic acid (DMAA) by hydride generation was demonstrated. The instrument used was a d.c. plasma atomic emission spectrometer (OCP-AES). Complete recovery was reported for As(III), As(V), and DMAA while 86% recovery was reported for MMAA. Detection limits were determined, as arsenic for the species listed previously, to be 1.2, 0.8, 1.1, and 1.0 ngemL-l, respectively. Precision values, at 50 ngemL-1 arsenic concentration, were f.80/0, 2.50/0, 2.6% and 2.6% relative standard deviation, respectively. The L-cysteine reagent was compared directly with the conventional hydride generation technique which uses a potassium iodide-hydrochloric acid medium. Recoveries using L-cysteine when compared with the conventional method provided the following results: similar recoveries were obtained for As(III), slightly better recoveries were obtained for As(V) and MMAA, and significantly better recoveries for DMAA. In addition, tall and sharp peak shapes were observed for all four species when using L-cysteine. The arsenic speciation method involved separation by ion exchange .. high perfonnance liquid chromatography (HPLC) with on-line hydride generation using the L.. cysteine reagent and measurement byOCP-AES. Total analysis time per sample was 12 min while the time between the start of subsequent runs was approximately 20 min. A binary . gradient elution program, which incorporated the following two eluents: 0.01 and 0.5 mM tri.. sodium citrate both containing 5% methanol (v/v) and both at a pH of approximately 9, was used during the separation by HPLC. Recoveries of the four species which were measured as peak area, and were normalized against As(III), were 880/0, 290/0, and 40% for DMAA, MMAA and As(V), respectively. Resolution factors between adjacent analyte peaks of As(III) and DMAA was 1.1; DMAA and MMAA was 1.3; and MMAA and As(V) was 8.6. During the arsenic speciation study, signals from the d.c. plasma optical system were measured using a new photon-signal integrating device. The_new photon integrator developed and built in this laboratory was based on a previously published design which was further modified to reflect current available hardware. This photon integrator was interfaced to a personal computer through an AID convertor. The .photon integrator has adjustable threshold settings and an adjustable post-gain device.

A Study of role conflict, role ambiguity, locus of control, job satisfaction and participation in decision making among front-line vocational service workers for mentally retarded adults

This study was an investigation of individual and organizational factors, as perceived by front-line vocational service workers from Adult Rehabilitation Centres (ARC Industries) for mentally retarded adults. The specific variables which were measured included role conflict/role ambiguity (role factors), internal/external locus of control (individual differences), job satisfaction with work and supervision (job attitudes) and participation in deci~ion making (organizational factor). The exploration of these constructs was conducted by means of self-report questionnaires which were completed by sixty-nine out of a total of ninety front-line employees. The surveys were distributed in booklet form to nine distinct rehabilitation facilities from St. Catharines, West Lincoln, Greater Niagara, Port Colborne, WeIland, Fort Erie, Hamilton, Guelph and Brantford. The survey data was evaluated by the statisti.cal Package for the Social Sciences (SPSS) which used the Pearson Product Moment Correlation procedure and a compar~son of means test. A comparison of correlation coefficients test was also conducted. This statistical procedure was calculated mathematically. The results obtained from the statistical evaluation confirmed the prediction that self-reported measures of participation in decision making and satisfaction (work and supervision) would be negatively correlated with role conflict and role ambiguity. As well, the speculation that perceived satisfaction (work and supervision) would be positively correlated with participation in decision making was empirically supported. Internal and external locus of control did not contribute to a significant difference in r~sponses to role perceptions (conflict and ambiguity) , satisfaction (work and supervision) or the correlational relationship between participation in decision making and satisfaction (work and supervision). Overall, the findings from this study substantiated the importance of examining employee perceptions in the workplace and the interrelationships among individual and organizational variables. This research was considered a contribution to the general area of occupational stress and to the study of individuals in work organizations.

Engineering an improved adenovirus packaging cell line

Recombinant human adenovirus (Ad) vectors are being extensively explored for their use in gene therapy and recombinant vaccines. Ad vectors are attractive for many reasons, including the fact that (1) they are relatively safe, based on their use as live oral vaccines, (2) they can accept large transgene inserts, (3) they can infect dividing and postmitotic cells, and (4) they can be produced to high titers. However, there are also a number of major problems associated with Ad vectors, including transient foreign gene expression due to host cellular immune responses, problems with humoral immunity, and the creation of replication competent adenoviruses (RCA). Most Ad vectors contain deletions in the E1 region that allow for insertion of a transgene. However, the E1 gene products are required for replication and thus must be supplied in trans by a helper ceillille that will allow for the growth and packaging of the defective virus. For this purpose the 293 cell line (Graham et al., 1977) is used most often; however, homologous recombination between the vector and the cell line often results in the generation of RCA. The presence of RCA in batches of adenoviral vectors for clinical use is a safety risk because tlley . may result in the mobilization and spread of the replication-defective vector viruses, and in significant tissue damage and pathogenicity. The present research focused on the alteration of the 293 cell line such that RCA formation can be eliminated. The strategy to modify the 293 cells involved the removal of the first 380 bp of the adenovirus genome through the process of homologous recombination. The first step towards this goal involved identifying and cloning the left-end cellular-viral jUl1ction from 293 cells to assemble sequences required for homologous recombination. Polymerase chain reaction (PCR) was performed to clone the junction, and the clone was verified through sequencing. The plasn1id PAM2 was then constructed, which served as the targeting cassette used to modify the 293 cells. The cassette consisted of (1) the cellular-viral junction as the left-end region of homology, (2) the neo gene to use for positive selection upon tranfection into 293 cells, (3) the adenoviral genome from bp 380 to bp 3438 as the right-end region of homology, and (4) the HSV-tk gene to use for negative selection. The plasmid PAM2 was linearized to produce a double strand break outside the region of homology, and transfected into 293 cells using the calcium-phosphate technique. Cells were first selected for their resistance to the drug G418, and subsequently for their resistance to the drug Gancyclovir (GANC). From 17 transfections, 100 pools of G418f and GANCf cells were picked using cloning lings and expanded for screening. Genomic DNA was isolated from the pools and screened for the presence of the 380 bps using PCR. Ten of the most promising pools were diluted to single cells and expanded in order to isolate homogeneous cell lines. From these, an additional 100 G41Sf and GANef foci were screened. These preliminary screening results appear promising for the detection of the desired cell line. Future work would include further cloning and purification of the promising cell lines that have potentially undergone homologous recombination, in order to isolate a homogeneous cell line of interest.

ESL students' off-line and on-line texts : differences and similarities /

This study was undertaken to investigate any textual differences and similarities within essays written with a word processing program and an e-mail editor by non-native writers. It arose from many contradictions and a paucity of empirical research within the field of second language learning and electronic technology. To further explore these contradictory observations, 3 classes of intermediate level ESL (English as a Second Language) students v^ote 6 essays, alternating between a word processing program and an e-mail editor. Prior to the data collection, students read brief texts and responded to questions that focused upon three formal topics: immigration, economics, and multiculturalism. Data were examined for (a) the differences in the frequency counts of 12 cohesive devices, (b) sentence complexity, which focused upon the occurrences of simple and complex sentences, (c) the number of words within the writings, (d) the method of contextualization preferred by writers, and (e) any variations in the final grades of the students' texts that resulted from holistic rating. Results of analysis indicated that there were no statistically significant differences in the frequency counts of the linguistic features. Sentence complexity did not vary within the off-line and on-line essays. The average number of words found within the off-line essays was approximately 20% greater than within on-line essays. Contextualization methods were not different within word-processed or e-mailed essays. Finally, there was no difference in the quality of the texts when holistically rated.

The von Neumann Minimax Theorem and its relatives and a study of externality in on-line auctions

This work consists of a theoretical part and an experimental one. The first part provides a simple treatment of the celebrated von Neumann minimax theorem as formulated by Nikaid6 and Sion. It also discusses its relationships with fundamental theorems of convex analysis. The second part is about externality in sponsored search auctions. It shows that in these auctions, advertisers have externality effects on each other which influence their bidding behavior. It proposes Hal R.Varian model and shows how adding externality to this model will affect its properties. In order to have a better understanding of the interaction among advertisers in on-line auctions, it studies the structure of the Google advertisements networ.k and shows that it is a small-world scale-free network.

Micromorphology of Last Glacial Maximum Grounding line sediments around the Antarctic Peninsula

Sediments recovered from seven Last Glacial Maximum grounding lines sites, around the Antarctic Peninsula, were analyzed using micromorphology. This is the first evidence that grounding line sediments from around the Antarctic Peninsula have complex deformational histories and subglacial origins. It was determined that grounding zone wedge contain multiple units, or diamicton layers, with homogenized boundaries. The multiple diamicton units / layers are due to the accretionary formation of a grounding line wedge. All the sediments were deposited via deformation, and continual reincorporation, homogenization of lower diamicton layers by upper diamicton layers produced what macroscopically appeared to be a single massive diamicton unit. The morainal ridge that was sampled, alternatively, is composed of a single unit, or diamicton layer, that was subglacial in origin and believed to have been pushed out to form a ridge that was subsequently deformed via glacial push.