Synthesis of isotope-labelled methoxypyrazine compounds as internal standards and quantitative determination of aroma methoxypyrazines in water and wines by solid-phase extraction with isotope dilution-GC-MS /

An efficient way of synthesizing the deuterium labelled analogues of three methoxypyrazine compounds: 2-d3-methoxy-3-isopropylpyrazine, 2-d3-methoxy-3- isobutylpyrazine, and 2-d3-methoxy-3-secbutylpyrazine, has been developed. To confirm that the deuterium labels had been incorporated into the expected positions in the molecules synthesized, the relevant characterization by NMR, HRMS and GC/MS analysis was conducted. Another part of this work involved quantitative determination of methoxypyrazines in water and wines. Solid-phase extraction (SPE) proved to be a suitable means for the sample separation and concentration prior to GC/MS analysis.Such factors as the presence of ethanol, salt, and acid have been investigated which can influence the recovery by SPE for the pyrazines from the water matrix. Significantly, in this work comparatively simple fractional distillation was attempted to replace the conventional steam distillation for pre-concentrating a sample with a relatively large volume prior to SPE. Finally, a real wine sample spiked with the relevant isotope-labelled methoxypyrazines was quantitatively analyzed, revealing that the wine with 10 beetles per litre contained 138 ppt of 2-methoxy-3-isopropylpyrazine. Interestingly, we have also found that 2-methoxy-3-secbutylpyrazine exhibits an extremely low detection limit in GC/MS analysis compared with the detection limit of the other two methoxypyrazines: 2- methoxy-3-isopropylpyrazine and 2-methoxy-3-isobutylpyrazine.

Co-operative education and the development of self-esteem, an internal locus of control and work habits

This study compared approximately 50 grade 12 students studying In th~ co-operative education mode with approximately 50 grade 12 students studying in a traditional English course. Measures of self-esteem, locus of control and work habits were compared before and at the conclusion of one semester's involvement in the different programs. Using Coopersmith's Self-Esteem Inventory, the students who had chosen to study in the co-operative education mode scored significantly higher than the students in the traditional course. At the end of the semester, the co-operative education students' scores remained significantly higher than the English students'. Although the test showed no sjgnifi~ant changes in self-esteem. anecdotal reports indicated that co-operative education students had increased self-esteem over the semester. No significant differences in locus of control were observed between the two groups at any time. Significant differences in work habits were observed. While both groups had the same number of absences and the same marks before taking these courses, students who were involved in co-operative education had significantly fewer absences and significantly higher marks than the students studying in the traditional course. Anecdotal reports also indicated an improv~ment in work habits for students who had been involved in co-operative education. Recommendations of the study are for further research to determine more exactly how self-esteem and work habits develop in co-operative education students. Also. students. parents, teachers. and administrators need to be made aware of the success of this program.

Drivers of Local Firms’ Focus on Internal R&D in Emerging Economies and Their International Performance

Grounded on the resource-based view of the firm, the study of this thesis investigates the effect of four internal and external factors – engineer intensity, location, affiliation with the government, government funding – on Chinese firms’ decision to either invest in internal R&D activities or external R&D and the effect of this decision on the firms’ international market success. In addition, the moderating role of the presence of foreign firms in China is examined. To understand these relationships, the thesis’ theorization focuses on the issue of how firms can combine optimally the two options – “internal R&D” and “external R&D”. In this regard I juxtapose internal R&D and external R&D and compare their advantages and disadvantages. To test my model, I apply panel data from the Annual Industrial Survey Database provided by the Chinese National Bureau of Statistics. My results show that three of the four investigated factors affect Chinese firms’ resource allocation decisions; and effective resource allocation decisions lead effectively to international market success, strengthened by the presence of foreign firms in China. Moreover the findings bear several theoretical and managerial contributions. First I propose the last dimension of the “VRIO framework” – “organization” – as an endogenous component of the VRIO framework, as my study investigated how firms can effectively combine resources to generate a competitive advantage in terms of international market success. Previous academic literature so far focused on examining whether internal and external R&D are complements or substitutes. My study fills a gap in the literature by investigating the determinants of the efficient combination of the two strategies and the outcome of the combination. One of the managerial implications is that Chinese firms can learn from foreign companies that are present in China.

Efecto del CIDR (Controlled Internal Drug Release) aplicado después de la inseminación artificial sobre la tasa de preñez en vacas de carne.

Tesis (Maestro en Ciencias Veterinarias) UANL, 2009.

Public Reason that Speaks to People : Iris Marion Young and the Problem of Internal Exclusion

Dossier : In Memoriam, Iris Marion Young (1949-2006)

Synthesis of polyelectrolyte brushes on silica-based substrates through surface-initiated polymerization : brush characterization and responsiveness to variation in pH and ionic strength

Les brosses de polyélectrolytes font l’objet d’une attention particulière pour de nombreuses applications car elles présentent la capacité de changer de conformation et, par conséquent, de propriétés de surface en réponse aux conditions environnementales appliquées. Le contrôle des principaux paramètres de ces brosses telles que l'épaisseur, la composition et l'architecture macromoléculaire, est essentiel pour obtenir des polymères greffés bien définis. Ceci est possible avec la Polymérisation Radicalaire par Transfert d’Atomes - Initiée à partir de la Surface (PRTA-IS), qui permet la synthèse de brosses polymériques de manière contrôlée à partir d’une couche d'amorceurs immobilisés de manière covalente sur une surface. Le premier exemple d’une synthèse directe de brosses de poly(acide acrylique) (PAA) par polymérisation radicalaire dans l’eau a été démontré. Par greffage d’un marqueur fluorescent aux brosses de PAA et via l’utilisation de la microscopie de fluorescence par réflexion totale interne, le dégreffage du PAA en temps réel a pu être investigué. Des conditions environnementales de pH ≥ 9,5 en présence de sel, se sont avérées critiques pour la stabilité de la liaison substrat-amorceur, conduisant au dégreffage du polymère. Afin de protéger de l’hydrolyse cette liaison substrat-amorceur sensible et prévenir le dégreffage non souhaité du polymère, un espaceur hydrophobique de polystyrène (PS) a été inséré entre l'amorceur et le bloc de PAA stimuli-répondant. Les brosses de PS-PAA obtenues étaient stables pour des conditions extrêmes de pH et de force ionique. La réponse de ces brosses de copolymère bloc a été étudiée in situ par ellipsométrie, et le changement réversible de conformation collapsée à étirée, induit par les variations de pH a été démontré. De plus, des différences de conformation provenant des interactions du bloc de PAA avec des ions métalliques de valence variable ont été obtenues. Le copolymère bloc étudié semble donc prometteur pour la conception de matériaux répondant rapidement a divers stimuli. Par la suite, il a été démontré qu’un acide phosphonique pouvait être employé en tant qu’ amorceur PRTA-IS comme alternative aux organosilanes. Cet amorceur phosphonate a été greffé pour la première fois avec succès sur des substrats de silice et une PRTA-IS en milieux aqueux a permis la synthèse de brosses de PAA et de poly(sulfopropyl méthacrylate). La résistance accrue à l’hydrolyse de la liaison Sisubstrat-O- Pamorceur a été confirmée pour une large gamme de pH 7,5 à 10,5 et a permis l’étude des propriétés de friction des brosses de PAA sous différentes conditions expérimentales par mesure de forces de surface. Malgré la stabilité des brosses de PAA à haute charge appliquée, les études des propriétés de friction ne révèlent pas de changement significatif du coefficient de friction en fonction du pH et de la force ionique.

Integrated internal PIFA for UMTS operation of clamshell mobile phones

novel design of at internal PIFA integrated with an RF-shielding metal case for application in a clamshell or fielder-tvpe mobile phone is presented. The integrated PIFA has a bent and tapered radiating arm in order to easily fit in the casing of the clamshell mobile phone as an internal antenna. The integrated PlEA can also provide a wide operating bandwidth fir UM7S (1920-2170 MHz) operation. In addition, for the clamshell mobile phone in either the talk or standby condition, only a small effect on the operating bandwidth of the integrated PIFA is obtained. The experimental results of the proposed design are presented

Influence of Interface Surface Geometries In The Tensile Characteristics Of Friction Welded Joints From Aluminium Alloys

Friction welding is a solid state joining process that produces coalescence in materials, using the heat developed between surfaces through a combination of mechanical induced rubbing motion and applied load. In rotary friction welding technique heat is generated by the conversion of mechanical energy into thermal energy at the interface of the work pieces during rotation under pressure. Traditionally friction welding is carried out on a dedicated machine because of its adaptability to mass production. In the present work, steps were made to modify a conventional lathe to rotary friction welding set up to obtain friction welding with different interface surface geometries at two different speeds and to carry out tensile characteristic studies. The surface geometries welded include flat-flat, flat-tapered, tapered-tapered, concave-convex and convex-convex. A comparison of maximum load, breaking load and percentage elongation of different welded geometries has been realized through this project. The maximum load and breaking load were found to be highest for weld formed between rotating flat and stationary tapered at 500RPM and the values were 19.219kN and 14.28 kN respectively. The percentage elongation was found to be highest for weld formed between rotating flat and stationary flat at 500RPM and the value was 21.4%. Hence from the studies it is cleared that process parameter like “interfacing surface geometries” of weld specimens have strong influence on tensile characteristics of friction welded joints

A Comparative Study Of Tensile And Microstructural Characteristics Of Friction Welded Joints And Conventionally Welded Joints Of Aluminium Alloy 6061

Welding of high strength and low weight materials like Aluminium Alloys without any defects by conventional welding techniques is a major challenge in industries. Hence research on solid state welding techniques like Friction stir welding and Friction welding techniques have got much importance in joining of Aluminium alloys. However most of the industries are not changing conventional techniques as skilled workers are available on that area. Most common conventional welding techniques used for joining of Aluminium alloys are Gas welding and Arc welding. Friction welding is a solid-state welding process that generates heat through mechanical friction between a moving and a stationary component with the addition of a lateral force called “upset” to plast ically displace and fuse the materials. In this work, experimental study on tensile and micro structural characteristics of welded joints formed from conventional welding techniques and Rotary friction welding(suitable for weld specimens with circular cross section) has been carried out and the same were compared. The process parameters for arc welding used was 50-70 Amp reverse polarity DC and electrodes of 2.3mm diameter. In Gas welding, the parameters were oxy acetylene neural flame at 3200°C and 3mm electrodes . In the case of friction welding an axial pressure loading of 3Mpa with 5 MPa as upsetting pressure and 500 rpm were used to obtain good welded joints. Tensile characteristic studies of Arc welded joints and Gas welded joints showed 48% and 60 % variations respectively from the maximum load bearing characteristics of parent metal. In the case of friction welded joint, the variation was found to 46%. Micro structural evaluation of conventionally welded joints exhibited clear distinct zones of various weld regions. In the case of friction welded joint micro structural photographs showed comparable features both in parent metal and welded region. Thus the tensile characteristic study and microstructure evaluations proved that friction welded joints are good in both aspects compared to conventionally welded joints.

Analyse und Beschreibung des Innengewindefertigungsverfahrens Gewindefurchen auf Basis eines Modellversuchs

Das Gewindefurchen ist ein spanloses Fertigungsverfahren zur Herstellung von Innengewinden. Es bietet wesentliche Vorteile gegenüber der spanenden Innengewindeherstellung, wie z.B. keine Notwendigkeit zur Spanentsorgung, höhere Festigkeit der Gewindeflanken und eine erhöhte Prozessgeschwindigkeit. Um die Vorteile des Verfahrens unter wirtschaftlichen und technologischen Aspekten besser auszunutzen, bietet die Weiterentwicklung der Werkzeuggeometrie sowohl im makroskopischen als auch im mikroskopischen Bereich ein enormes Potential, welches nicht nur bezüglich der Standzeit bzw. Standmenge und Prozessgeschwindigkeit, sondern auch hinsichtlich der Qualität der erzeugten Gewinde erschlossen werden sollte. Durch die empirische Untersuchung der technischen und physikalischen Eigenschaften am Gewindefurcher sollen der Anformbereich und die Formkeilgeometrie in Abhängigkeit verschiedener Prozessparameter und Werkstoffe verbessert werden, um optimale Bearbeitungsergebnisse hinsichtlich der hergestellten Gewindefurchen und des auftretenden Verschleißes am Gewindefurcher bzw. Formkeils zu erreichen. Die Basis dieser Untersuchungen bildet ein neuartiger Modellversuch, bei dem modifizierte Gewindefurcher verwendet werden, die derart umgestaltet sind, dass von einem üblichen Gewindefurcher durch Umschleifen nur noch ein einzelner Gewindegang am Werkzeug verbleibt. Dadurch ist es möglich, in einer vergrößerten Vorbohrung mit einem Formkeil die einzelnen Umformstufen beim Gewindefurchen separat zu fertigen, die auftretenden Prozesskräfte während des Eingriffs in das Werkstück zu messen und das Bearbeitungsergebnis im Werkstück und den Verschleiß am Formkeil zu bewerten. Weiterhin wird eine rein theoretische Methode beschrieben, mit der die Berechnung der Umformkraft und darauf basierend der Furchmomente am Formkeil bzw. dem ganzen Gewindefurcher möglich ist. Durch die Kenntnis der berechneten Kräfte und Momente am einzelnen Formkeil bzw. dem Gewindefurcher kann bereits in der Konzeptionsphase eines Gewindefurchers eine Anpassung des Werkszeuges an die jeweiligen Bearbeitungsanforderungen durchgeführt werden, wodurch der Entwurf von Gewindefurchern wesentlich wirtschaftlicher realisierbar ist, als durch rein empirische Herangehensweisen.

Smallholder group certification in Uganda - Analysis of internal control systems in two organic export companies

The organic agricultural sector of Uganda is among the most developed in Africa in terms of its professional institutional network and high growth rates of number of certified farmers and land area. Smallholder farmers are certified organic through contract production for export companies using a group certification scheme (internal control system - ICS). The ICS is a viable and well-accepted tool to certify small-scale producers in developing countries all over the world. Difficulties in certification are still stated to be among the main constraints for Uganda’s organic sector development. Therefore, this paper reports a qualitative case study comprising 34 expert interviews in two organic fresh-produce export companies in central Uganda, aiming to explore the challenges which underlie organic certification with ICS. The study shows that farmers cannot be labelled as ‘organic by default’ but deliberately engage in organic production as a marketing strategy. The small quantities purchased by the organic companies lead to a difficult marketing situation for the farmers, causing production and infiltration risks on the farm level. These risks require increased control that challenges the companies organizationally. The risks and control needs are a reason to involve farmers in ICS procedures and innovatively adapt the ICS by means of a bypass around formal perspective restrictions. The paper discusses different perspectives on risks, risk control and certification.

Internal Camera Calibration Using Rotation and Geometric Shapes

This paper describes a simple method for internal camera calibration for computer vision. This method is based on tracking image features through a sequence of images while the camera undergoes pure rotation. The location of the features relative to the camera or to each other need not be known and therefore this method can be used both for laboratory calibration and for self calibration in autonomous robots working in unstructured environments. A second method of calibration is also presented. This method uses simple geometric objects such as spheres and straight lines to The camera parameters. Calibration is performed using both methods and the results compared.

Relative Contributions of Internal and External Features to Face Recognition

The central challenge in face recognition lies in understanding the role different facial features play in our judgments of identity. Notable in this regard are the relative contributions of the internal (eyes, nose and mouth) and external (hair and jaw-line) features. Past studies that have investigated this issue have typically used high-resolution images or good-quality line drawings as facial stimuli. The results obtained are therefore most relevant for understanding the identification of faces at close range. However, given that real-world viewing conditions are rarely optimal, it is also important to know how image degradations, such as loss of resolution caused by large viewing distances, influence our ability to use internal and external features. Here, we report experiments designed to address this issue. Our data characterize how the relative contributions of internal and external features change as a function of image resolution. While we replicated results of previous studies that have shown internal features of familiar faces to be more useful for recognition than external features at high resolution, we found that the two feature sets reverse in importance as resolution decreases. These results suggest that the visual system uses a highly non-linear cue-fusion strategy in combining internal and external features along the dimension of image resolution and that the configural cues that relate the two feature sets play an important role in judgments of facial identity.