Design Guide and Construction Specifications for National Pollutant Discharge Elimination System (NPDES) Site Runoff Control, 2006

According to the 1972 Clean Water Act, the Environmental Protection Agency (EPA) established a set of regulations for the National Pollutant Discharge Elimination System (NPDES). The purpose of these regulations is to reduce pollution of the nation’s waterways. In addition to other pollutants, the NPDES regulates stormwater discharges associated with industrial activities, municipal storm sewer systems, and construction sites. Phase II of the NPDES stormwater regulations, which went into effect in Iowa in 2003, applies to construction activities that disturb more than one acre of ground. The regulations also require certain communities with Municipal Separate Storm Sewer Systems (MS4) to perform education, inspection, and regulation activities to reduce stormwater pollution within their communities. Iowa does not currently have a resource to provide guidance on the stormwater regulations to contractors, designers, engineers, and municipal staff. The Statewide Urban Design and Specifications (SUDAS) manuals are widely accepted as the statewide standard for public improvements. The SUDAS Design manual currently contains a brief chapter (Chapter 7) on erosion and sediment control; however, it is outdated, and Phase II of the NPDES stormwater regulations is not discussed. In response to the need for guidance, this chapter was completely rewritten. It now escribes the need for erosion and sediment control and explains the NPDES stormwater regulations. It provides information for the development and completion of Stormwater Pollution Prevention Plans (SWPPPs) that comply with the stormwater regulations, as well as the proper design and implementation of 28 different erosion and sediment control practices. In addition to the design chapter, this project also updated a section in the SUDAS Specifications manual (Section 9040), which describes the proper materials and methods of construction for the erosion and sediment control practices.

Optimal Design of Permit Markets with an Ex Ante Pollution Target, August 2006

In this paper, we examine the design of permit trading programs when the objective is to minimize the cost of achieving an ex ante pollution target, that is, one that is defined in expectation rather than an ex post deterministic value. We consider two potential sources of uncertainty, the presence of either of which can make our model appropriate: incomplete information on abatement costs and uncertain delivery coefficients. In such a setting, we find three distinct features that depart from the well-established results on permit trading: (1) the regulator’s information on firms’ abatement costs can matter; (2) the optimal permit cap is not necessarily equal to the ex ante pollution target; and (3) the optimal trading ratio is not necessarily equal to the delivery coefficient even when it is known with certainty. Intuitively, since the regulator is only required to meet a pollution target on average, she can set the trading ratio and total permit cap such that there will be more pollution when abatement costs are high and less pollution when abatement costs are low. Information on firms’ abatement costs is important in order for the regulator to induce the optimal alignment between pollution level and abatement costs.

The politics of contaminated sites management : institutional regime change and actor's mode of participation in the environmental management of the Bonfol Chemical Waste Landfill in Switzerland

By the end of the 1970s, contaminated sites had emerged as one of the most complex and urgent environmental issues affecting industrialized countries. The authors show that small and prosperous Switzerland is no exception to the pervasive problem of sites contamination, the legacy of past practices in waste management having left some 38,000 contaminated sites throughout the country. This book outlines the problem, offering evidence that open and polycentric environmental decision-making that includes civil society actors is valuable. They propose an understanding of environmental management of contaminated sites as a political process in which institutions frame interactions between strategic actors pursuing sometimes conflicting interests. In the opening chapter, the authors describe the influences of politics and the power relationships between actors involved in decision-making in contaminated sites management, which they term a "wicked problem." Chapter Two offers a theoretical framework for understanding institutions and the environmental management of contaminated sites. The next five chapters present a detailed case study on environmental management and contaminated sites in Switzerland, focused on the Bonfol Chemical Landfill. The study and analysis covers the establishment of the landfill under the first generation of environmental regulations, its closure and early remediation efforts, and the gambling on the remediation objectives, methods and funding in the first decade of the 21st Century. The concluding chapter discusses the question of whether the strength of environmental regulations, and the type of interactions between public, private, and civil society actors can explain the environmental choices in contaminated sites management. Drawing lessons from research, the authors debate the value of institutional flexibility for dealing with environmental issues such as contaminated sites.

Higher education in nursing: the faculty work process in different institutional contexts

Objective To analyze the characteristics of faculty work in nursing higher education. Method An exploratory qualitative study with a theoretical-methodological framework of dialectical and historical materialism. The faculty work process was adopted as the analytical category, grounded on conceptions of work and professionalism. Semi-structured interviews were conducted with 24 faculty members from three higher education institutions in the city of São Paulo, classified according to the typology of institutional contexts. Results The faculty members at these higher education institutions are a heterogeneous group, under different working conditions. Intensification and precarious conditions of the faculty work is common to all three contexts, although there are important distinctions in the practices related to teaching, research and extension. Conclusion Faculty professionalization can be the starting point for analyzing and coping with such a distinct reality of faculty work and practice.


‘Poverty…, of course we have it…’ Notes for the analysis of an institutional

Based on testimonies by Cape Verdean individuals with different social condition and institutional responsibility on one hand and, on the other hand, on the consideration of the historical burden and the policies adopted after the independence, this article is focused on the creation of a social conscience about poverty and the manifestations of micro-violence through the action of institutions and NGOs committed in the eradication of poverty and prevention of behaviors potentially generating and perpetuating micro-violence and social exclusion. The political environment and the perception of an involvement of Cape Verdeans in a common destiny are deemed crucial to the achievement of these purposes.

Experimental design on the simplex

Optimum experimental designs depend on the design criterion, the model andthe design region. The talk will consider the design of experiments for regressionmodels in which there is a single response with the explanatory variables lying ina simplex. One example is experiments on various compositions of glass such asthose considered by Martin, Bursnall, and Stillman (2001).Because of the highly symmetric nature of the simplex, the class of models thatare of interest, typically Scheff´e polynomials (Scheff´e 1958) are rather differentfrom those of standard regression analysis. The optimum designs are also ratherdifferent, inheriting a high degree of symmetry from the models.In the talk I will hope to discuss a variety of modes for such experiments. ThenI will discuss constrained mixture experiments, when not all the simplex is availablefor experimentation. Other important aspects include mixture experimentswith extra non-mixture factors and the blocking of mixture experiments.Much of the material is in Chapter 16 of Atkinson, Donev, and Tobias (2007).If time and my research allows, I would hope to finish with a few comments ondesign when the responses, rather than the explanatory variables, lie in a simplex.ReferencesAtkinson, A. C., A. N. Donev, and R. D. Tobias (2007). Optimum ExperimentalDesigns, with SAS. Oxford: Oxford University Press.Martin, R. J., M. C. Bursnall, and E. C. Stillman (2001). Further results onoptimal and efficient designs for constrained mixture experiments. In A. C.Atkinson, B. Bogacka, and A. Zhigljavsky (Eds.), Optimal Design 2000,pp. 225–239. Dordrecht: Kluwer.Scheff´e, H. (1958). Experiments with mixtures. Journal of the Royal StatisticalSociety, Ser. B 20, 344–360.1

Validation of the New Mix Design Process for Cold In-Place Rehabilitation Using Foamed Asphalt, 2007

Asphalt pavement recycling has grown dramatically over the last few years as a viable technology to rehabilitate existing asphalt pavements. Iowa's current Cold In-place Recycling (CIR) practice utilizes a generic recipe specification to define the characteristics of the CIR mixture. As CIR continues to evolve, the desire to place CIR mixture with specific engineering properties requires the use of a mix design process. A new mix design procedure was developed for Cold In-place Recycling using foamed asphalt (CIR-foam) in consideration of its predicted field performance. The new laboratory mix design process was validated against various Reclaimed Asphalt Pavement (RAP) materials to determine its consistency over a wide range of RAP materials available throughout Iowa. The performance tests, which include dynamic modulus test, dynamic creep test and raveling test, were conducted to evaluate the consistency of a new CIR-foam mix design process to ensure reliable mixture performance over a wide range of traffic and climatic conditions. The “lab designed” CIR will allow the pavement designer to take the properties of the CIR into account when determining the overlay thickness.

Effective Shoulder Design and Maintenance, 2007

Granular shoulders are an important element of the transportation system and are constantly subjected to performance problems due to wind- and water-induced erosion, rutting, edge drop-off, and slope irregularities. Such problems can directly affect drivers’ safety and often require regular maintenance. The present research study was undertaken to investigate the factors contributing to these performance problems and to propose new ideas to design and maintain granular shoulders while keeping ownership costs low. This report includes observations made during a field reconnaissance study, findings from an effort to stabilize the granular and subgrade layer at six shoulder test sections, and the results of a laboratory box study where a shoulder section overlying a soft foundation layer was simulated. Based on the research described in this report, the following changes are proposed to the construction and maintenance methods for granular shoulders: • A minimum CBR value for the granular and subgrade layer should be selected to alleviate edge drop-off and rutting formation. • For those constructing new shoulder sections, the design charts provided in this report can be used as a rapid guide based on an allowable rut depth. The charts can also be used to predict the behavior of existing shoulders. • In the case of existing shoulder sections overlying soft foundations, the use of geogrid or fly ash stabilization proved to be an effective technique for mitigating shoulder rutting.

Retinal thickening in HLA-B27 associated acute anterior uveitis: evolution with time and association with severity of inflammatory activity.

Purpose: To describe the evolution of retinal thickness in eyes affected with acute anterior uveitis (AAU) in the course of follow-up and to assess its correlation with severity of inflammatory activity in the anterior chamber. Methods: Design: Prospective, cohort study Setting: Institutional study Patient population: 72 eyes (affected and fellow eyes) of 36 patients Observation procedure: Patients were followed daily until beginning of resolution of inflammatory activity and weekly thereafter. Optical coherence tomography and laser flare photometry were performed at each visit. Treatment consisted of topical corticosteroids Main outcome measures: Retinal thickness of affected eyes, difference in retinal thickness between affected and fellow eyes and their evolution in time, association between maximal retinal thickness and initial laser flare photometry. Results: Difference in retinal thickness between affected and fellow eyes became significant on average seven days from baseline and remained so through-out follow-up (p<0.001). There was a steep increase in retinal thickness of affected eyes followed by a progressive decrease after reaching a peak value. Maximal difference in retinal thickness between affected and fellow eyes was observed between 17 and 25 days from baseline and exhibited a strong, positive correlation with initial laser flare photometry values (p=0.015). Conclusions: Retinal thickness in eyes affected with AAU presents a steep increase over 3 to 4 weeks and then gradually decreases. Severity of inflammation at baseline predicts the amount of retinal thickening in affected eyes. A characteristic pattern of temporal response of retinal anatomy to inflammatory stimuli seems to arise.

How accurate are surveyed preferences for public policies? Evidence from a unique institutional setup

Opinion polls are widely used to capture public sentiments on a varietyof issues. If citizens are unwilling to reveal certain policy preferences toothers, opinion polls may fail to characterize population preferences accurately.The innovation of this paper is to use unique data to measurebiases in opinion polls for a broad range of policies. I combine data on184 referenda held in Switzerland between 1987 and 2007, with postballotsurveys that ask for each proposal how the citizens voted. Thedifference between stated preferences in the survey and revealed preferences at the ballot box provides a direct measure of bias in opinion polls.I find that these biases vary by policy areas, with the largest ones occurring in policies on immigration, international integration, and votesinvolving liberal/conservative attitudes. Also, citizens show a tendencyto respond in accordance to the majority.

The Acute STroke Registry and Analysis of Lausanne (ASTRAL): design and baseline analysis of an ischemic stroke registry including acute multimodal imaging.

BACKGROUND AND PURPOSE: Stroke registries are valuable tools for obtaining information about stroke epidemiology and management. The Acute STroke Registry and Analysis of Lausanne (ASTRAL) prospectively collects epidemiological, clinical, laboratory and multimodal brain imaging data of acute ischemic stroke patients in the Centre Hospitalier Universitaire Vaudois (CHUV). Here, we provide design and methods used to create ASTRAL and present baseline data of our patients (2003 to 2008). METHODS: All consecutive patients admitted to CHUV between January 1, 2003 and December 31, 2008 with acute ischemic stroke within 24 hours of symptom onset were included in ASTRAL. Patients arriving beyond 24 hours, with transient ischemic attack, intracerebral hemorrhage, subarachnoidal hemorrhage, or cerebral sinus venous thrombosis, were excluded. Recurrent ischemic strokes were registered as new events. RESULTS: Between 2003 and 2008, 1633 patients and 1742 events were registered in ASTRAL. There was a preponderance of males, even in the elderly. Cardioembolic stroke was the most frequent type of stroke. Most strokes were of minor severity (National Institute of Health Stroke Scale [NIHSS] score ≤ 4 in 40.8% of patients). Cardioembolic stroke and dissections presented with the most severe clinical picture. There was a significant number of patients with unknown onset stroke, including wake-up stroke (n=568, 33.1%). Median time from last-well time to hospital arrival was 142 minutes for known onset and 759 minutes for unknown-onset stroke. The rate of intravenous or intraarterial thrombolysis between 2003 and 2008 increased from 10.8% to 20.8% in patients admitted within 24 hours of last-well time. Acute brain imaging was performed in 1695 patients (97.3%) within 24 hours. In 1358 patients (78%) who underwent acute computed tomography angiography, 717 patients (52.8%) had significant abnormalities. Of the 1068 supratentorial stroke patients who underwent acute perfusion computed tomography (61.3%), focal hypoperfusion was demonstrated in 786 patients (73.6%). CONCLUSIONS: This hospital-based prospective registry of consecutive acute ischemic strokes incorporates demographic, clinical, metabolic, acute perfusion, and arterial imaging. It is characterized by a high proportion of minor and unknown-onset strokes, short onset-to-admission time for known-onset patients, rapidly increasing thrombolysis rates, and significant vascular and perfusion imaging abnormalities in the majority of patients.

Cost system design and cost management in the Spanish public sector

Cost systems have been shown to have developed considerably in recent years andactivity-based costing (ABC) has been shown to be a contribution to cost management,particularly in service businesses. The public sector is composed to a very great extentof service functions, yet considerably less has been reported of the use of ABC tosupport cost management in this sector.In Spain, cost systems are essential for city councils as they are obliged to calculate thecost of the services subject to taxation (eg. waste collection, etc). City councils musthave a cost system in place to calculate the cost of services, as they are legally requirednot to profit , from these services.This paper examines the development of systems to support cost management in theSpanish Public Sector. Through semi-structured interviews with 28 subjects within oneCity Council it contains a case study of cost management. The paper contains extractsfrom interviews and a number of factors are identified which contribute to thesuccessful development of the cost management system.Following the case study a number of other City Councils were identified where activity-based techniques had either failed or stalled. Based on the factors identified inthe single case study a further enquiry is reported. The paper includes a summary usingstatistical analysis which draws attention to change management, funding and politicalincentives as factors which had an influence on system success or failure.