Análise tribo-termodinâmica da aplicação de nanopartículas de Al2O3 como aditivo lubrificante em compressor hermético de refrigeração

The thermodynamic performance of a refrigeration system can be improved by reducing the compression work by a particular technique for a specific heat removal rate. This study examines the effect of small concentrations of Al2O3 (50 nm) nanoparticles dispersion in the mineral oil based lubricant on the: viscosity, thermal conductivity, and lubrication characteristics as well as the overall performance (based on the Second Law of Thermodynamics) of the refrigerating system using R134a or R600a as refrigerants. The study looked at the influences of variables: i) refrigerant charge (100, 110, 120 and 130 g), ii) rotational speed of the condenser blower (800 and 1100 RPM) and iii) nanoparticle concentration (0.1 and 0.5 g/l) on the system performance based on the Taguchi method in a matrix of L8 trials with the criterion "small irreversibility is better”. They were carried pulldown and cycling tests according to NBR 12866 and NBR 12869, respectively, to evaluate the operational parameters: on-time ratio, cycles per hour, suction and discharge pressures, oil sump temperature, evaporation and condensation temperatures, energy consumption at the set-point, total energy consumption and compressor power. In order to evaluate the nanolubricant characteristics, accelerated tests were performed in a HFRR bench. In each 60 minutes test with nanolubricants at a certain concentration (0, 0.1 and 0.5 g/l), with three replications, the sphere (diameter 6.00 ± 0.05 mm, Ra 0.05 ± 0.005 um, AISI 52100 steel, E = 210 GPa, HRC 62 ± 4) sliding on a flat plate (cast iron FC200, Ra <0.5 ± 0.005 um) in a reciprocating motion with amplitude of 1 mm, frequency 20 Hz and a normal load of 1,96 N. The friction coefficient signals were recorded by sensors coupled to the HFRR system. There was a trend commented bit in the literature: a nanolubricant viscosity reduction at the low nanoparticles concentrations. It was found the dominant trend in the literature: increased thermal conductivity with increasing nanoparticles mass fraction in the base fluid. Another fact observed is the significant thermal conductivity growth of nanolubricant with increasing temperature. The condenser fan rotational speed is the most influential parameter (46.192%) in the refrigerator performance, followed by R600a charge (38.606%). The Al2O3 nanoparticles concentration in the lubricant plays a minor influence on system performance, with 12.44%. The results of power consumption indicates that the nanoparticles addition in the lubricant (0.1 g/L), together with R600a, the refrigerator consumption is reduced of 22% with respect to R134a and POE lubricant. Only the Al2O3 nanoparticles addition in the lubricant results in a consumption reduction of about 5%.

Medium change monitoring using ambient seismic noise and coda wave interferometry: examples from intraplate NE Brazil and the Mid-Atlantic Ridge

This thesis presents and discusses the results of ambient seismic noise correlation for two different environments: intraplate and Mid-Atlantic Ridge. The coda wave interferometry method has also been tested for the intraplate data. Ambient noise correlation is a method that allows to retrieve the structural response between two receivers from ambient noise records, as if one of the station was a virtual source. It has been largely used in seismology to image the subsurface and to monitor structural changes associated mostly with volcanic eruptions and large earthquakes. In the intraplate study, we were able to detect localized structural changes related to a small earthquake swarm, which main event is mR 3.7, North-East of Brazil. We also showed that the 1-bit normalization and spectral whitening result on the loss of waveform details and that the phase auto-correlation, which is amplitude unbiased, seems to be more sensitive and robust for our analysis of a small earthquake swarm. The analysis of 6 months of data using cross-correlations detect clear medium changes soon after the main event while the auto-correlations detect changes essentially after 1 month. It could be explained by fluid pressure redistribution which can be initiated by hydromechanical changes and opened path ways to shallower depth levels due to later occurring earthquakes. In the Mid-Atlantic Ridge study, we investigate structural changes associated with a mb 4.9 earthquake in the region of the Saint Paul transform fault. The data have been recorded by a single broadband seismic station located at less than 200 km from the Mid-Atlantic ridge. The results of the phase auto-correlation for a 5-month period, show a strong co-seismic medium change followed by a relatively fast post-seismic recovery. This medium change is likely related to the damages caused by the earthquake’s ground shaking. The healing process (filling of the new cracks) that lasted 60 days can be decomposed in two phases, a fast recovery (70% in ~30 days) in the early post-seismic stage and a relatively slow recovery later (30% in ~30 days). In the coda wave interferometry study, we monitor temporal changes of the subsurface caused by the small intraplate earthquake swarm mentioned previously. The method was first validated with synthetics data. We were able to detect a change of 2.5% in the source position and a 15% decrease of the scatterers’ amount. Then, from the real data, we observed a rapid decorrelation of the seismic coda after the mR 3.7 seismic event. This indicates a rapid change of the subsurface in the fault’s region induced by the earthquake.

Medium change monitoring using ambient seismic noise and coda wave interferometry: examples from intraplate NE Brazil and the Mid-Atlantic Ridge

This thesis presents and discusses the results of ambient seismic noise correlation for two different environments: intraplate and Mid-Atlantic Ridge. The coda wave interferometry method has also been tested for the intraplate data. Ambient noise correlation is a method that allows to retrieve the structural response between two receivers from ambient noise records, as if one of the station was a virtual source. It has been largely used in seismology to image the subsurface and to monitor structural changes associated mostly with volcanic eruptions and large earthquakes. In the intraplate study, we were able to detect localized structural changes related to a small earthquake swarm, which main event is mR 3.7, North-East of Brazil. We also showed that the 1-bit normalization and spectral whitening result on the loss of waveform details and that the phase auto-correlation, which is amplitude unbiased, seems to be more sensitive and robust for our analysis of a small earthquake swarm. The analysis of 6 months of data using cross-correlations detect clear medium changes soon after the main event while the auto-correlations detect changes essentially after 1 month. It could be explained by fluid pressure redistribution which can be initiated by hydromechanical changes and opened path ways to shallower depth levels due to later occurring earthquakes. In the Mid-Atlantic Ridge study, we investigate structural changes associated with a mb 4.9 earthquake in the region of the Saint Paul transform fault. The data have been recorded by a single broadband seismic station located at less than 200 km from the Mid-Atlantic ridge. The results of the phase auto-correlation for a 5-month period, show a strong co-seismic medium change followed by a relatively fast post-seismic recovery. This medium change is likely related to the damages caused by the earthquake’s ground shaking. The healing process (filling of the new cracks) that lasted 60 days can be decomposed in two phases, a fast recovery (70% in ~30 days) in the early post-seismic stage and a relatively slow recovery later (30% in ~30 days). In the coda wave interferometry study, we monitor temporal changes of the subsurface caused by the small intraplate earthquake swarm mentioned previously. The method was first validated with synthetics data. We were able to detect a change of 2.5% in the source position and a 15% decrease of the scatterers’ amount. Then, from the real data, we observed a rapid decorrelation of the seismic coda after the mR 3.7 seismic event. This indicates a rapid change of the subsurface in the fault’s region induced by the earthquake.

Estudo da injeção de água e gás em um reservatório com características do pré-sal brasileiro

The pre-salt province is composed by large amounts of light oil and with good quality, a reality that puts Brazil in a strategic position facing the great demand for energy worldwide. In this province are the largest discoveries in the world in the last ten years; areas as Libra, Franco and Lula field, everyone containing volumes greater than 8 billion recoverable oil barrels. To develop and optimize the production of these fields, a study was done for choosing the improved oil recovery methods. The main motivations were the presence of carbon dioxide (CO2) as a contaminant and the strategic decision of do not discard it, combined with high GOR (gas-oil ratio) of the reservoir fluid. The method should take advantage of the unique abundant resources: seawater and produced gas. This way, the process of matching these resources in the water alterning gas injection (WAG) became a good option. In this master’s dissertation, it was developed a reservoir model with average characteristics of the Brazilian pre-salt, where was applied the improved oil recovery method of water alternating gas. The production of this reservoir was analyzed by parameters as: the first fluid injected in the injection process, position of the injection wells completion, injection water and gas rate and cycle time. The results showed a good performance of the method, with up to 26% of gains in the recovery factor regarding the primary recovery, since the application of water injection and gas, individually, was not able to overcome 10 % of gain. The most influential parameter found in the results was the cycle time, with higher recovery factor values obtained with the use of shorter times.

Mecanismos celulares activados por receptores P2Y₂ en los procesos ciliares: implicaciones en la hipertensión ocular y el glaucoma

El glaucoma es una neuropatía óptica crónica de etiología multifactorial, que provoca una pérdida progresiva e irreversible de la visión debida a la degeneración de los axones del nervio óptico y la muerte apoptótica de las células ganglionares de la retina (Downs et al., 2011; Quigley, 2011; Soto et al., 2014). Actualmente es la principal causa de ceguera irreversible en el mundo (Pascolini et al., 2012). Aunque su etiología aún no está clara, se sabe que el principal factor de riesgo para desarrollar la enfermedad es el aumento de la PIO debido a anomalías en la dinámica del humor acuoso (Casson et al., 2012). La presencia de receptores purinérgicos P2X y P2Y ha sido descrita en las principales estructuras oculares relacionadas con la producción y drenaje del humor acuoso, los procesos ciliares y la malla trabecular, que son bañadas por dicho fluido (Guzman-­‐Aranguez et al., 2013). Al mismo tiempo, se ha referido la presencia del dinucleótido Ap4A, agonista de dichos receptores, en el humor acuoso, y cómo sus niveles se veían significativamente incrementados en pacientes glaucomatosos (Castany et al., 2011). El objetivo de esta tesis ha sido evaluar la implicación de los receptores purinérgicos P2Y2 de los procesos ciliares en la hipertensión ocular. Más concretamente determinar el papel del Ap4A a través de la activación de dichos receptores sobre la movilización del ion cloruro y del agua a través de las proteínas acuaporinas (AQPs), principales componentes del humor acuoso. Por otra parte, se ha investigado el origen de los niveles incrementados de Ap4A debidos al aumento de la PIO, caracterizando uno de los posibles sensores celulares implicados en dicho proceso. Al mismo tiempo se han evaluado y caracterizado los diferentes mecanismos implicados en dicha liberación...

Investigação experimental das propriedades termofísicas e da convecção forçada de nanofluido de grafeno

This work presents an experimental investigation of thermal hydraulic performance of the nanofluid composed by graphene nanoparticles dispersed in a mixture of water and ethylene glycol at a ratio of 70:30% by volume. The tests were carried out under forced convection inside a circular tube with uniform heat flux on the wall for the laminar-turbulent transition regime. The mass flow rate ranged from 40 to 70 g/s corresponding to Reynolds numbers between 3000 and 7500. The heat flux was maintained constant at values of 11, 16 and 21 kW/m², as well as the inlet temperature of 15, 20 and 25°C. Three samples were produced with the nanofluid volumetric concentration of 0.05%, 0.10% and 0.15%. Thermophysical properties were experimentaly measured for all samples that were critically compared and discussed with theoretical models most commonly used in the literature. Initially, experiments with distilled water confirmed the validity of the experimental equipment for the thermo-hydraulic tests. Therefore, nanofluid samples that showed the highest thermal conductivity, corresponding to the volumetric concentrations of 0.15% and 0.10%, were subjected to the tests. The thermal-hydraulic performance for both samples was unsatisfactory. The heat transfer coefficients for convection of nanofluids reduced 21% in average, for the sample with = 0.15% and 26% and for =0.10%. The pressure drop of the samples was higher than the base fluid. Finally, the pressure drop and heat transfer coefficient by convection of both samples were also compared to theoretical models. The models used for pressure drop showed an excellent agreement with experimental results, which is remarkable considering the transitional flow.

Las representaciones construidas por estudiantes universitarios acerca del modelo científico de membrana citoplasmática. Diagnóstico y relevancia en el proceso de enseñanza aprendizaje

Aprender ciencia requiere aprender modelos y reconstruirlos en el aula. Los docentes que enseñan ciencia utilizan habitualmente en sus clases modelos científicos, los cuales constituyen una forma de representar la realidad. Se les atribuye a los modelos diferentes funciones: representar estructuras y fenómenos, ayudar en la visualización de entidades abstractas o microscópicas, asistir en la interpretación de resultados experimentales, entre otras. Los modelos científicos requieren un elevado nivel de abstracción, esto hace que muchas veces el alumnado encuentre dificultad en la comprensión e interpretación de los mismos. El presente trabajo se propone caracterizar las representaciones construidas por alumnos universitarios de la carrera de Psicología sobre el modelo de membrana citoplasmática y analizar su utilidad en las clases de Biología y su relevancia en el proceso de enseñanza aprendizaje. Para este fin se utilizó como instrumento una encuesta, elaborada ad hoc, que fue procesada a través de una estrategia metodológica mixta, estableciendo categorías. A partir del análisis del modelo explícito de la membrana citoplasmática expresado por los alumnos en las respuestas, se pondrán de manifiesto las características de los modelos mentales elaborados por ellos. De los resultados se desprende que aquellas investigaciones que se propongan interpretar la manera en que las personas construyen sus representaciones sobre determinados fenómenos, aportarán a la didáctica de las ciencias para mejorar el aprendizaje de los estudiantes; por otro lado se concluye que la analogía del modelo de membrana como mosaico fluido resulta poco significativa para los alumnos, que a menudo incorporan estos conceptos memorísticamente, representando un modelo que no es completamente científico. El trabajo con imágenes exige la mediación didáctica; resulta por eso necesario que los docentes comprendan que el razonamiento basado en modelos es una habilidad altamente deseable, pero requiere extenso entrenamiento y práctica dentro del ámbito áulico

Las representaciones construidas por estudiantes universitarios acerca del modelo científico de membrana citoplasmática. Diagnóstico y relevancia en el proceso de enseñanza aprendizaje

Aprender ciencia requiere aprender modelos y reconstruirlos en el aula. Los docentes que enseñan ciencia utilizan habitualmente en sus clases modelos científicos, los cuales constituyen una forma de representar la realidad. Se les atribuye a los modelos diferentes funciones: representar estructuras y fenómenos, ayudar en la visualización de entidades abstractas o microscópicas, asistir en la interpretación de resultados experimentales, entre otras. Los modelos científicos requieren un elevado nivel de abstracción, esto hace que muchas veces el alumnado encuentre dificultad en la comprensión e interpretación de los mismos. El presente trabajo se propone caracterizar las representaciones construidas por alumnos universitarios de la carrera de Psicología sobre el modelo de membrana citoplasmática y analizar su utilidad en las clases de Biología y su relevancia en el proceso de enseñanza aprendizaje. Para este fin se utilizó como instrumento una encuesta, elaborada ad hoc, que fue procesada a través de una estrategia metodológica mixta, estableciendo categorías. A partir del análisis del modelo explícito de la membrana citoplasmática expresado por los alumnos en las respuestas, se pondrán de manifiesto las características de los modelos mentales elaborados por ellos. De los resultados se desprende que aquellas investigaciones que se propongan interpretar la manera en que las personas construyen sus representaciones sobre determinados fenómenos, aportarán a la didáctica de las ciencias para mejorar el aprendizaje de los estudiantes; por otro lado se concluye que la analogía del modelo de membrana como mosaico fluido resulta poco significativa para los alumnos, que a menudo incorporan estos conceptos memorísticamente, representando un modelo que no es completamente científico. El trabajo con imágenes exige la mediación didáctica; resulta por eso necesario que los docentes comprendan que el razonamiento basado en modelos es una habilidad altamente deseable, pero requiere extenso entrenamiento y práctica dentro del ámbito áulico

Las representaciones construidas por estudiantes universitarios acerca del modelo científico de membrana citoplasmática. Diagnóstico y relevancia en el proceso de enseñanza aprendizaje

Aprender ciencia requiere aprender modelos y reconstruirlos en el aula. Los docentes que enseñan ciencia utilizan habitualmente en sus clases modelos científicos, los cuales constituyen una forma de representar la realidad. Se les atribuye a los modelos diferentes funciones: representar estructuras y fenómenos, ayudar en la visualización de entidades abstractas o microscópicas, asistir en la interpretación de resultados experimentales, entre otras. Los modelos científicos requieren un elevado nivel de abstracción, esto hace que muchas veces el alumnado encuentre dificultad en la comprensión e interpretación de los mismos. El presente trabajo se propone caracterizar las representaciones construidas por alumnos universitarios de la carrera de Psicología sobre el modelo de membrana citoplasmática y analizar su utilidad en las clases de Biología y su relevancia en el proceso de enseñanza aprendizaje. Para este fin se utilizó como instrumento una encuesta, elaborada ad hoc, que fue procesada a través de una estrategia metodológica mixta, estableciendo categorías. A partir del análisis del modelo explícito de la membrana citoplasmática expresado por los alumnos en las respuestas, se pondrán de manifiesto las características de los modelos mentales elaborados por ellos. De los resultados se desprende que aquellas investigaciones que se propongan interpretar la manera en que las personas construyen sus representaciones sobre determinados fenómenos, aportarán a la didáctica de las ciencias para mejorar el aprendizaje de los estudiantes; por otro lado se concluye que la analogía del modelo de membrana como mosaico fluido resulta poco significativa para los alumnos, que a menudo incorporan estos conceptos memorísticamente, representando un modelo que no es completamente científico. El trabajo con imágenes exige la mediación didáctica; resulta por eso necesario que los docentes comprendan que el razonamiento basado en modelos es una habilidad altamente deseable, pero requiere extenso entrenamiento y práctica dentro del ámbito áulico

Levantamento do Tamanho Médio de Bolhas em Escoamento Bifásico Vertical por Técnica Fotográfica

Para confirmar e validar códigos computacionais de escoamento de fluidos, importantes na segurança de reatores nucleares, é preciso que sejam realizadas medidas experimentais. Como a geração de vapor no fluido refrigerante diminui a eficiência de troca térmica a fração de vazio passa a ser um dos parâmetros mais importantes a ser obtido, e que, num escoamento vertical, pode ser conhecido através da quantidade de bolha e seu diâmetro médio.

Studio del campo di velocità per fluidi in moto laminare all'interno di condotti

Lo scopo di questa tesi è quello di ottenere una rappresentazione grafica del profilo di velocità di un fluido all’interno di un condotto. In particolare si studieranno le equazioni di bilancio facendo alcune ipotesi semplificative riguardo il moto del fluido. Si considererà un moto laminare in condizione di completo sviluppo dinamico e convezione forzata. Grazie a queste ipotesi si riuscirà ad ottenere un’equazione semplificata di Navier-Stokes, che permetterà di calcolare l’andamento della velocità all’interno di condotti con qualsiasi forma della sezione. In questo caso si confronterà il profilo di velocità di un condotto a sezione circolare con uno a sezione circolare forata come in uno scambiatore di calore a tubi concentrici. Per risolvere l’equazione di Navier-Stokes e stampare l’andamento delle velocità all’interno della sezione del condotto si è utilizzato il software “Mathematica”, che è stato appreso durante l’attività di tirocinio curriculare. Questo software offre un supporto notevole allo studio matematico di qualsiasi problema. Permette inoltre di avere un riscontro grafico dei risultati ottenuti, direttamente nell’interfaccia utilizzata per la stesura del codice. Per rappresentare il profilo di velocità sarà inoltre utilizzato il metodo degli elementi finiti all’interno di Mathematica, che permetterà di ottenere una soluzione più uniforme e vicina alla realtà. Il metodo degli elementi finiti (FEM) permette di semplificare lo studio del moto di un fluido, in quanto ci dà la possibilità di avere un sistema di equazioni algebriche che ne descrivono il moto, invece di equazioni differenziali e le sue relative condizioni al contorno. Sarà quindi brevemente descritto questo metodo che è stato di grande aiuto tramite l’implementazione della “mesh” su Mathematica.

Analisi sperimentale del funzionamento di un sistema micro-ORC

Questa tesi tratta nello specifico lo studio di un impianto micro-ORC, capace di sfruttare acqua alla temperatura di circa 70-90°C come sorgente termica. Questo sistema presenta una potenza dichiarata dal costruttore pari a 3kW e un rendimento del 9%. In primo luogo, si descrivono le caratteristiche principali dei fluidi organici, in particolare quelle del freon R134a, impiegato nel banco prova. Vengono illustrati dettagliatamente l’impianto e la sensoristica utilizzata per le misurazioni delle varie grandezze fisiche. Tramite esse, con l’utilizzo di un programma di acquisizione dati appositamente relizzato in ambiente LabVIEW, è stato possibile calcolare in tempo reale tutti i parametri di funzionamento, necessari per la caratterizzazione del sistema. Per una veloce ed efficiente elaborazione dei dati registrati durante le prove in laboratorio, è stato realizzato un programma in linguaggio VBA. L’utilizzo di questo codice ha permesso, in primo luogo, di individuare e correggere eventuali errori di calcolo e acquisizione presenti in ambiente LabVIEW e, in secondo luogo, si è reso indispensabile per comprendere il funzionamento dell’impianto nelle varie fasi, come accensione, spegnimento e produzione di potenza. Sono state inoltre identificate le modalità di risposta del sistema al variare dei comandi impostabili dall’utente, quali il numero di giri della pompa e la variazione della temperatura della sorgente calda. Si sono poi osservate le risposte del sistema al variare delle condizioni esterne, come ad esempio la temperatura dell’acqua di condensazione. Una specifica prova è stata analizzata in questo elaborato. Durante tale prova il sistema ha lavorato in forte off-design, erogando una potenza elettrica pari a 255 W, raggiungendo un basso valore del rendimento (pari a 1.8%). L’analisi dei dati ha portato ad identificare nuovi limiti di funzionamento, legati ad esempio alla quantità di fluido interna al sistema.

Estudo numérico do escoamento em descarregadores por orifício

Atualmente, no estudo do comportamento de descarregadores de cheias por orifício, é necessário conhecer as pressões ao longo do descarregador, para várias alturas de água na albufeira. Este tipo de estudos tem sido usualmente realizado recorrendo a ensaios experimentais. No entanto, a utilização de modelos numéricos para a simulação do escoamento em estruturas hidráulicas encontra-se numa fase emergente. Neste sentido, a presente dissertação pretende apresentar um estudo numérico relativo ao escoamento em descarregadores de cheias por orifício. Por forma a efetuar o estudo numérico, foi utlizado o programa comercial de CFD FLOW-3D®, reproduzindo um modelo reduzido construído no Laboratório Nacional de Engenharia Civil (LNEC) correspondente a um descarregador por orifício. Para a realização das simulações numéricas foi necessário definir o objeto de estudo, a malha de cálculo, as condições de fronteira e as propriedades do fluido e objeto de modo a reproduzir as situações ensaiadas experimentalmente no LNEC. A proximidade dos resultados experimentais e numéricos para vários níveis de água na albufeira permitiu validar o modelo numérico para este tipo de escoamentos no interior do orifício.

Development of variable displacement oil pump for internal combustion engines

In the last years the need to develop more environmentally friendly and efficient cars as led to the development of several technologies to improve the performance of internal combustion engines, a large part of the innovations are focused in the auxiliary systems of the engine, including, the oil pump, this is an element of great importance in the dynamics of the engine as well a considerable energy consumer. Most solutions for oil pumps to this day are fixed displacement, for medium and high speeds, the pump flow rate is higher than the needs of the engine, this excess flow leads to the need for recirculation of the fluid which represents a waste of energy. Recently, technological advances in this area have led to the creation of variable displacement oil pumps, these have become a 'must have' due to the numerous advantages they bring, although the working principle of vane or piston pumps is relatively well known, the application of this technology for the automotive industry is new and brings new challenges. The focus of this dissertation is to develop a new concept of variable displacement system for automotive oil pumps. The main objective is to obtain a concept that is totally adaptable to existing solutions on the market (engines), both dimensionally as in performance specifications, having at the same time an innovative mechanical system for obtaining variable displacement. The developed design is a vane pump with variable displacement going in line with existing commercial solutions, however, the variation of the eccentricity commonly used to provide an variable displacement delivery is not used, the variable displacement is achieved without varying the eccentricity of the system but with a variation of the length of the pumping chamber. The principle of operation of the pump is different to existing solutions while maintaining the ability to integrate standard parts such as control valves and mechanical safety valves, the pump is compatible with commercial solutions in terms of interfaces for connection between engine systems and pump. A concept prototype of the product was obtained in order to better evaluate the validity of the concept. The developed concept represents an innovation in oil pumps design, being unique in its mechanical system for variable displacement delivery.

Concentrador solar multi-modo

El objeto de la invención es un captador solar constituido por un concentrador cilindroparabólico (CCP) aislado térmicamente (4), una cubierta de vidrio en su plano de apertura (1), un absorbedor tubular situado en su foco por el que circula un fluido caloportador (3), con o sin encapsulamiento de vidrio (2), y un mecanismo de lamas rotativas absorbedoras (5). El invento permite, mediante la rotación de las lamas, optar entre un modo de operación en concentración solar en el absorbedor focal para el aprovechamiento de la radiación solar directa (3) y un modo de operación en placa plana convencional para aprovechamiento de la radiación solar global (6). Su uso se propone como parte de instalaciones solares térmicas con el fin de a) alimentar con un solo elemento procesos que presentan demandas combinadas de baja y media temperatura en función de su programación temporal o estacional, b) permitir un aprovechamiento solar suplementario en instalaciones de CCP durante períodos de radiación directa reducida y c) contar con capacidad adicional de regulación de temperatura y radiación.