Management of irrigation frequency and nitrogen fertilization to mitigate GHG and NO emissions from drip-fertigated crops

Drip irrigation combined with split application of fertilizer nitrogen (N) dissolved in the irrigation water (i.e. drip fertigation) is commonly considered best management practice for water and nutrient efficiency. As a consequence, its use is becoming widespread. Some of the main factors (water-filled pore space, NH4+ and NO3−) regulating the emissions of greenhouse gases (i.e. N2O, CO2 and CH4) and NO from agroecosystems can easily be manipulated by drip fertigation without yield penalties. In this study, we tested management options to reduce these emissions in a field experiment with a melon (Cucumis melo L.) crop. Treatments included drip irrigation frequency (weekly/daily) and type of N fertilizer (urea/calcium nitrate) applied by fertigation. Crop yield, environmental parameters, soil mineral N concentrations and fluxes of N2O, NO, CH4 and CO2 were measured during 85 days. Fertigation with urea instead of calcium nitrate increased N2O and NO emissions by a factor of 2.4 and 2.9, respectively (P < 0.005). Daily irrigation reduced NO emissions by 42% (P < 0.005) but increased CO2 emissions by 21% (P < 0.05) compared with weekly irrigation. We found no relation between irrigation frequency and N2O emissions. Based on yield-scaled Global Warming Potential as well as NO cumulative emissions, we conclude that weekly fertigation with a NO3−-based fertilizer is the best option to combine agronomic productivity with environmental sustainability. Our study shows that adequate management of drip fertigation, while contributing to the attainment of water and food security, may provide an opportunity for climate change mitigation.

Efficiency and environmental indexes to evaluate the sustainability of mineral and organic fertilization in an irrigated melon crop

Melon is traditionally cultivated in fertigated farmlands in the center of Spain with high inputs of water and N fertilizer. Excess N can have a negative impact, from the economic point of view, since it can diminish the production and quality of the fruit, from the environmental point of view, since it is a very mobile element in the soil and can contaminate groundwater. From health point of view, nitrate can be accumulated in fruit pulp, and, in addition, groundwater is the fundamental supply source of human populations. Best management practices are particularly necessary in this region as many zones have been declared vulnerable to NO3- pollution (Directive 91/676/CEE) During successive years, a melon crop (Cucumis melo L.) was grown under field conditions applying mineral and organic fertilizers under drip irrigation. Different doses of ammonium nitrate were used as well as compost derived from the wine-distillery industry which is relevant in this area. The present study reviews the most common N efficiency indexes under the different management options with a view to maximizing yield and minimizing N loss.

Strain rate effect on semi‐crystalline plla mechanical properties measured by instrumented indentation tests

Poly(L‐lactide) is a widely studied biomaterial, currently approved for use in a range of medical devices. Its mechanical properties can be tailored giving the material different crystallinity degrees. PLLA presents a complex non‐linear behaviour that depends not only on structural parameters such as crystallinity degree but also on external parameters such as strain rate and temperature. Failure of polymeric implants is attributed to their intrinsic time‐dependent performance under static loading conditions.

Application of user-centered design in the development of an atomated/assisted testing system for self-service devices

Automated Teller Machines (ATMs) are sensitive self-service systems that require important investments in security and testing. ATM certifications are testing processes for machines that integrate software components from different vendors and are performed before their deployment for public use. This project was originated from the need of optimization of the certification process in an ATM manufacturing company. The process identifies compatibility problems between software components through testing. It is composed by a huge number of manual user tasks that makes the process very expensive and error-prone. Moreover, it is not possible to fully automate the process as it requires human intervention for manipulating ATM peripherals. This project presented important challenges for the development team. First, this is a critical process, as all the ATM operations rely on the software under test. Second, the context of use of ATMs applications is vastly different from ordinary software. Third, ATMs’ useful lifetime is beyond 15 years and both new and old models need to be supported. Fourth, the know-how for efficient testing depends on each specialist and it is not explicitly documented. Fifth, the huge number of tests and their importance implies the need for user efficiency and accuracy. All these factors led us conclude that besides the technical challenges, the usability of the intended software solution was critical for the project success. This business context is the motivation of this Master Thesis project. Our proposal focused in the development process applied. By combining user-centered design (UCD) with agile development we ensured both the high priority of usability and the early mitigation of software development risks caused by all the technology constraints. We performed 23 development iterations and finally we were able to provide a working solution on time according to users’ expectations. The evaluation of the project was carried out through usability tests, where 4 real users participated in different tests in the real context of use. The results were positive, according to different metrics: error rate, efficiency, effectiveness, and user satisfaction. We discuss the problems found, the benefits and the lessons learned in the process. Finally, we measured the expected project benefits by comparing the effort required by the current and the new process (once the new software tool is adopted). The savings corresponded to 40% less effort (man-hours) per certification. Future work includes additional evaluation of product usability in a real scenario (with customers) and the measuring of benefits in terms of quality improvement.

Design and optimization of optical, fiber based PSK demodulators for high-bit-rate optical networks

El objetivo principal de esta tesis ha sido el diseño y la optimización de receptores implementados con fibra óptica, para ser usados en redes ópticas de alta velocidad que empleen formatos de modulación de fase. En los últimos años, los formatos de modulación de fase (Phase Shift keying, PSK) han captado gran atención debido a la mejora de sus prestaciones respecto a los formatos de modulación convencionales. Principalmente, presentan una mejora de la eficiencia espectral y una mayor tolerancia a la degradación de la señal causada por la dispersión cromática, la dispersión por modo de polarización y los efectos no-lineales en la fibra óptica. En este trabajo, se analizan en detalle los formatos PSK, incluyendo sus variantes de modulación de fase diferencial (Differential Phase Shift Keying, DPSK), en cuadratura (Differential Quadrature Phase Shift Keying, DQPSK) y multiplexación en polarización (Polarization Multiplexing Differential Quadrature Phase Shift Keying, PM-DQPSK), con la finalidad de diseñar y optimizar los receptores que permita su demodulación. Para ello, se han analizado y desarrollado nuevas estructuras que ofrecen una mejora en las prestaciones del receptor y una reducción de coste comparadas con las actualmente disponibles. Para la demodulación de señales DPSK, en esta tesis, se proponen dos nuevos receptores basados en un interferómetro en línea Mach-Zehnder (MZI) implementado con tecnología todo-fibra. El principio de funcionamiento de los MZI todo-fibra propuestos se asienta en la interferencia modal que se produce en una fibra multimodo (MMF) cuando se situada entre dos monomodo (SMF). Este tipo de configuración (monomodo-multimodo-monomodo, SMS) presenta un buen ratio de extinción interferente si la potencia acoplada en la fibra multimodo se reparte, principal y equitativamente, entre dos modos dominantes. Con este objetivo, se han estudiado y demostrado tanto teórica como experimentalmente dos nuevas estructuras SMS que mejoran el ratio de extinción. Una de las propuestas se basa en emplear una fibra multimodo de índice gradual cuyo perfil del índice de refracción presenta un hundimiento en su zona central. La otra consiste en una estructura SMS con las fibras desalineadas y donde la fibra multimodo es una fibra de índice gradual convencional. Para las dos estructuras, mediante el análisis teórico desarrollado, se ha demostrado que el 80 – 90% de la potencia de entrada se acopla a los dos modos dominantes de la fibra multimodo y se consigue una diferencia inferior al 10% entre ellos. También se ha demostrado experimentalmente que se puede obtener un ratio de extinción de al menos 12 dB. Con el objeto de demostrar la capacidad de estas estructuras para ser empleadas como demoduladores de señales DPSK, se han realizado numerosas simulaciones de un sistema de transmisión óptico completo y se ha analizado la calidad del receptor bajo diferentes perspectivas, tales como la sensibilidad, la tolerancia a un filtrado óptico severo o la tolerancia a las dispersiones cromática y por modo de polarización. En todos los casos se ha concluido que los receptores propuestos presentan rendimientos comparables a los obtenidos con receptores convencionales. En esta tesis, también se presenta un diseño alternativo para la implementación de un receptor DQPSK, basado en el uso de una fibra mantenedora de la polarización (PMF). A través del análisi teórico y del desarrollo de simulaciones numéricas, se ha demostrado que el receptor DQPSK propuesto presenta prestaciones similares a los convencionales. Para complementar el trabajo realizado sobre el receptor DQPSK basado en PMF, se ha extendido el estudio de su principio de demodulación con el objeto de demodular señales PM-DQPSK, obteniendo como resultado la propuesta de una nueva estructura de demodulación. El receptor PM-DQPSK propuesto se basa en la estructura conjunta de una única línea de retardo junto con un rotador de polarización. Se ha analizado la calidad de los receptores DQPSK y PM-DQPSK bajo diferentes perspectivas, tales como la sensibilidad, la tolerancia a un filtrado óptico severo, la tolerancia a las dispersiones cromática y por modo de polarización o su comportamiento bajo condiciones no-ideales. En comparación con los receptores convencionales, nuestra propuesta exhibe prestaciones similares y además permite un diseño más simple que redunda en un coste potencialmente menor. En las redes de comunicaciones ópticas actuales se utiliza la tecnología de multimplexación en longitud de onda (WDM) que obliga al uso de filtros ópticos con bandas de paso lo más estrechas posibles y a emplear una serie de dispositivos que incorporan filtros en su arquitectura, tales como los multiplexores, demultiplexores, ROADMs, conmutadores y OXCs. Todos estos dispositivos conectados entre sí son equivalentes a una cadena de filtros cuyo ancho de banda se va haciendo cada vez más estrecho, llegando a distorsionar la forma de onda de las señales. Por esto, además de analizar el impacto del filtrado óptico en las señales de 40 Gbps DQPSK y 100 Gbps PM-DQPSK, este trabajo de tesis se completa estudiando qué tipo de filtro óptico minimiza las degradaciones causadas en la señal y analizando el número máximo de filtros concatenados que permiten mantener la calidad requerida al sistema. Se han estudiado y simulado cuatro tipos de filtros ópticos;Butterworth, Bessel, FBG y F-P. ABSTRACT The objective of this thesis is the design and optimization of optical fiber-based phase shift keying (PSK) demodulators for high-bit-rate optical networks. PSK modulation formats have attracted significant attention in recent years, because of the better performance with respect to conventional modulation formats. Principally, PSK signals can improve spectrum efficiency and tolerate more signal degradation caused by chromatic dispersion, polarization mode dispersion and nonlinearities in the fiber. In this work, many PSK formats were analyzed in detail, including the variants of differential phase modulation (Differential Phase Shift Keying, DPSK), in quadrature (Differential Quadrature Phase Shift Keying, DQPSK) and polarization multiplexing (Polarization Multiplexing Differential Quadrature Phase Shift Keying, PM-DQPSK), in order to design and optimize receivers enabling demodulations. Therefore, novel structures, which offer good receiver performances and a reduction in cost compared to the current structures, have been analyzed and developed. Two novel receivers based on an all-fiber in-line Mach-Zehnder interferometer (MZI) were proposed for DPSK signal demodulation in this thesis. The operating principle of the all-fiber MZI is based on the modal interference that occurs in a multimode fiber (MMF) when it is located between two single-mode fibers (SMFs). This type of configuration (Single-mode-multimode-single-mode, SMS) can provide a good extinction ratio if the incoming power from the SMF could be coupled equally into two dominant modes excited in the MMF. In order to improve the interference extinction ratio, two novel SMS structures have been studied and demonstrated, theoretically and experimentally. One of the two proposed MZIs is based on a graded-index multimode fiber (MMF) with a central dip in the index profile, located between two single-mode fibers (SMFs). The other one is based on a conventional graded-index MMF mismatch spliced between two SMFs. Theoretical analysis has shown that, in these two schemes, 80 – 90% of the incoming power can be coupled into the two dominant modes exited in the MMF, and the power difference between them is only ~10%. Experimental results show that interference extinction ratio of 12 dB could be obtained. In order to demonstrate the capacity of these two structures for use as DPSK signal demodulators, numerical simulations in a completed optical transmission system have been carried out, and the receiver quality has been analyzed under different perspectives, such as sensitivity, tolerance to severe optical filtering or tolerance to chromatic and polarization mode dispersion. In all cases, from the simulation results we can conclude that the two proposed receivers can provide performances comparable to conventional ones. In this thesis, an alternative design for the implementation of a DQPSK receiver, which is based on a polarization maintaining fiber (PMF), was also presented. To complement the work made for the PMF-based DQPSK receiver, the study of the demodulation principle has been extended to demodulate PM-DQPSK signals, resulting in the proposal of a novel demodulation structure. The proposed PM-DQPSK receiver is based on only one delay line and a polarization rotator. The quality of the proposed DQPSK and PM-DQPSK receivers under different perspectives, such as sensitivity, tolerance to severe optical filtering, tolerance to chromatic dispersion and polarization mode dispersion, or behavior under non-ideal conditions. Compared with the conventional receivers, our proposals exhibit similar performances but allow a simpler design which can potentially reduce the cost. The wavelength division multiplexing (WDM) technology used in current optical communications networks requires the use of optical filters with a passband as narrow as possible, and the use of a series of devices that incorporate filters in their architecture, such as multiplexers, demultiplexers, switches, reconfigurable add-drop multiplexers (ROADMs) and optical cross-connects (OXCs). All these devices connected together are equivalent to a chain of filters whose bandwidth becomes increasingly narrow, resulting in distortion to the waveform of the signals. Therefore, in addition to analyzing the impact of optical filtering on signal of 40 Gbps DQPSK and 100 Gbps PM-DQPSK, we study which kind of optical filter minimizes the signal degradation and analyze the maximum number of concatenated filters for maintaining the required quality of the system. Four types of optical filters, including Butterworth, Bessel, FBG and FP, have studied and simulated.

Water and nitrogen footprint in an irrigated crop under mineral and organic fertilization

In order to establish rational nitrogen (N) application and reduce groundwater contamination, a clearer understanding of the N distribution through the growing season and its balance is crucial. Excessive doses of N and/or water applied to fertigated crops involve a substantial risk of aquifer contamination by nitrate; but knowledge of N cycling and availability within the soil could assist in avoiding this excess. In central Spain, the main horticultural fertigated crop is the melon type ?piel de sapo¿ and it is cultivated in vulnerable zones to nitrate pollution (Directive 91/676/CEE). However, until few years ago there were not antecedents related to the optimization of nitrogen fertilization together with irrigation. Water and N footprint are indicators that allow assessing the impact generated by different agricultural practices, so they can be used to improve the management strategies in fertigated crop systems. The water footprint distinguishes between blue water (sources of water applied to the crop, like irrigation and precipitation), green water (water used by the crop and stored in the soil), and it is furthermore possible to quantify the impact of pollution by calculating the grey water, which is defined as the volume of polluted water created from the growing and production of crops. On the other hand, the N footprint considers green N (nitrogen consumed by the crops and stored in the soil), blue N (N available for crop, like N applied with mineral and/or organic fertilizers, N applied with irrigation water and N mineralized during the crop period), whereas grey N is the amount of N-NO3- washed from the soil to the aquifer. All these components are expressed as the ratio between the components of water or N footprint and the yield (m3 t-1 or kg N t-1 respectively). The objetives of this work were to evaluate the impact derivated from the use of different fertilizer practices in a melon crop using water and N footprint.

Rate-Adaptive LDPC-based key reconciliation for high performance quantum key distribution

The postprocessing or secret-key distillation process in quantum key distribution (QKD) mainly involves two well-known procedures: information reconciliation and privacy amplification. Information or key reconciliation has been customarily studied in terms of efficiency. During this, some information needs to be disclosed for reconciling discrepancies in the exchanged keys. The leakage of information is lower bounded by a theoretical limit, and is usually parameterized by the reconciliation efficiency (or inefficiency), i.e. the ratio of additional information disclosed over the Shannon limit. Most techniques for reconciling errors in QKD try to optimize this parameter. For instance, the well-known Cascade (probably the most widely used procedure for reconciling errors in QKD) was recently shown to have an average efficiency of 1.05 at the cost of a high interactivity (number of exchanged messages). Modern coding techniques, such as rate-adaptive low-density parity-check (LDPC) codes were also shown to achieve similar efficiency values exchanging only one message, or even better values with few interactivity and shorter block-length codes.

Comparison of Existing Formulae for Estimating the Overtopping Rate in Harbour Breakwaters

The purpose of the research work resulting from various studies undertaken in the CEDEX, as summarized in this article, is to make a comparative analysis of methods for calculating overtopping rates developed by different authors. To this effect, in the first place, existing formulae for estimating the overtopping rate on rubble mound and vertical breakwaters were summarised and analysed. Later, the above mentioned formulae were compared using the results obtained in a series of hydraulic model tests at the CEDEX (the Center of Studies of Ports and Coasts of the CEDEX, Madrid, Spain). A calculation method based on the neural network theory, developed in the European CLASH Project, was applied to a series of sloping breakwater tests in order to complete this research. The results obtained in the Ferrol, Ciervana and Alicante breakwaters tests are presented here.

Crecimiento forestal en el bosque tropical de montaña: efectos de la diversidad florística y de la manipulación de nutrientes

El bosque tropical de montaña, es considerado zona de mega diversidad y de alto grado de endemismo, por las diferentes zonas ecológicas que presenta. Durante las últimas décadas estos bosques han recibido mayor atención por parte de investigadores, sin embargo, aún existe poca investigación en determinar cuáles son las respuestas de los bosques a los cambios ambientales a los que son sometidos. Estos bosques están sufriendo serias amenazas como pérdida de cobertura vegetal y cambios en los ciclos de nutrientes. El trabajo se dividió en cuatro objetivos específicos. i) Caracterización y análisis de patrones altitudinales de la riqueza de especies en el bosque tropical de montaña en el sur del Ecuador; con el fin de conocer cómo varía la diversidad de especies riqueza lo largo de un gradiente altitudinal. ii) Conocer los patrones espaciales del crecimiento en tres remanentes boscosos de un bosque tropical de montaña para determinar cómo la vecindad y la semejanza funcional de ésta influyen en el crecimiento forestal. iii) Conocer los efectos de la fertilización en el crecimiento diamétrico de especies arbóreas, en el bosque tropical de montaña; se analizó cómo reaccionan los árboles a la adición de nutrientes N y P en tres tipos de bosque. iv) Saber la respuesta de la comunidad de árboles a la adición de nutrientes en el bosque montano andino; este objetivo se basó con el supuesto de la deficiencia de tres tipos de nutrientes N, P y Ca, en esta formación boscosa y cómo reaccionan los árboles a la adición de nutrientes. El presente trabajo se llevó a cabo, en el bosque tropical de montaña que se encuentra localizada en la parte adyacente del Parque Nacional Podocarpus (PNP) en la cordillera del Consuelo, forma parte de la cadena oriental de los Andes del sur del Ecuador El trabajo de desarrollo entre los años 2008 y 2014. Para abordar el primer objetivo se establecieron 54 parcelas ubicadas aleatoriamente a lo largo de un gradiente altitudinal (3 niveles de altitud) y se e midieron e identificaron todos los individuos mayores a 5cm de DAP. Se construyó una filogenia con Phylocom y se calcularon diferentes componentes de diversidad para cada parcela ( riqueza taxonómica, diversidad filogenética y edad media de las especies). Ajustando modelos lineares se contrastó el efecto de la altitud sobre dichos componentes y se vio que la riqueza taxonómica y la edad media de las especies aumentaron con la altitud, en sentido contrario a las predicciones de la "hipótesis del conservadurismo tropical" (Tropical Conservatism Hypothesis). Para abordar el segundo objetivo se realizó una remedición de todos los árboles cartografiados en tres parcelas permanentes de alrededor de 5000 m2 cada una, representativas de tres estados diferentes de la sucesión del bosque montano. A partir de las coordenadas y de los datos de registrados, y empleando diferentes funciones de correlación de marca se analizó la distribución espacial del tamaño y del crecimiento relativo y del tamaño. Se constató que mientras que el tamaño de los árboles presentó una correlación espacial negativa, el crecimiento presentó correlación espacial positiva, en ambos casos a distancias cortas. El rango y la magnitud de ambas correlaciones aumentaron al avanzar la sucesión. La distribución espacial del crecimiento mostró una correlación negativa con la distribución espacial de tamaños. Por otro lado, la distribución espacial del crecimiento mostró una correlación negativa para árboles semejantes funcionalmente y positiva cuando se calculó entre árboles con diferente estrategia funcional. En conjunto, los resultados obtenidos señalan un aumento de la importancia de procesos competitivos y una mayor estructuración espacial del crecimiento y de la distribución de tamaños al avanzar la sucesión. Para el tercer y cuarto objetivo se instalaron 52 parcelas distribuidas en bloques donde se fertilizaron dos veces al año durante 6,4 años, se identificaron todos los individuos mayores a 10 cm de DAP, y se midió el crecimiento diamétrico durante estos años Con la adición de nutrientes realizada a los diferentes tipos de bosque en la gradiente altitudinal, encontramos que el efecto sobre el crecimiento diamétrico en la comunidad varia con el rango altitudinal, y el tipo de nutriente, analizando a nivel de las especies, en la mayoría de los casos las especies comunes no tuvieron cambios significativos a la adición de nutrientes. Los resultados de este estudio aportan nuevas evidencias para el entendimiento de la diversidad, estructura y dinámica de los bosques tropicales de montaña. ABSTRACT The montane tropical forest is considered a megadiverse habitat that harbor an enormous degree of endemism. This is mainly due to the high degree of environmental heterogeneity found and the presence of different well defined ecological areas. These forests have received more attention during the last decades, however, the information regarding the responses of these forests to environmental change, is still scarce. These forests are seriously endangered and are suffering serious threats, such as loss of vegetative cover, changes in the nutrient cycles. The work was divided in four specific objectives: i) Characterization and analysis of the species richness altitudinal patterns in the montane tropical forest of south Ecuador. Specifically, how species diversity changes along altitudinal gradients. ii) Exploring the spatial patterns of tree growth in three remnants of a montane tropical forest, and analyze how tree neighborhood and functional similarity among trees influence tree growth. Tropical Conservatism Hypothesis iii) Understanding the effects of fertilization in arboreal species growth (increase in diameter) of the montane tropical forest. Specifically we studied the effects of P and N addition on three different forests across an altitudinal gradient. iv) Know the response of the community of trees to the addition of nutrients in the Andean montane forest; this objective was based on the supposition of deficiency of three types of nutrients: P, N and Ca in this forest all formation and how the trees react to the addition of these nutrients. The present work was carried out in the montane tropical forest located in Bombuscaro, San Francisco and Cajanuma close to Podocarpus National Park (PNP) on Consuelo mountain range (Andean oriental range) at South of Ecuador. Field work was carried out during 2008 and 2014. To address the first objective, we randomly placed 54 plots along an altitudinal gradient. In these plots, every individual larger than 5 cm of DBH was measured and identified. A phylogeny was build with Phylocom and different diversity components (taxonomic richness, phylogenetic diversity and average species age) were computed for each plot. Linear models were used to test the effects of altitude on the diversity components. Our results showed that, contrary to the Tropical Conservatism Hypothesis, both taxonomic richness and average species age increased with altitude. To address our second objective, all mapped trees in three successional permanent plots (around ~5000 m2 each) were re-measured. Using different mark correlation functions, we analyzed the spatial distribution of tree-size and tree relative growth rate. Whereas tree size showed negative spatial correlation at fine spatial scales, relative growth rate showed positive correlation at the same scales. The range and magnitude of those correlations increased along successional stage. The spatial distribution of the relative growth rate was negatively correlated with the spatial distribution of tree sizes. Additionally, we found that the spatial correlation of the relative growth rate was negative for functionally similar trees and positive when computed for functionally different trees. In synthesis, our results point to an increase of competitive processes and strong spatial structure of relative growth rate and tree size along succession. For the third and fourth objectives, 52 plots were placed in a block design and were fertilized twice a year for 6,4 years. In these plots all the individuals with DBH > 10 cm were identified, and the diametrical growth was measured during these years. The nutrient addition at the three different altitude forests, revealed that the effect on the diametrical growth in the community varied with the altitudinal range. When analyzed at species level, the addition of nutrients was no significant in most cases. These results represent new evidences that will improved our understanding of diversity patterns and structure, and the dynamics of tropical montane forests.

Methodology for instantaneous average exhaust gas mass flow rate measurement

This paper presents a new methodology for measurement of the instantaneous average exhaust mass flow rate in reciprocating internal combustion engines to be used to determinate real driving emissions on light duty vehicles, as part of a Portable Emission Measurement System (PEMS). Firstly a flow meter, named MIVECO flow meter, was designed based on a Pitot tube adapted to exhaust gases which are characterized by moisture and particle content, rapid changes in flow rate and chemical composition, pulsating and reverse flow at very low engine speed. Then, an off-line methodology was developed to calculate the instantaneous average flow, considering the ?square root error? phenomenon. The paper includes the theoretical fundamentals, the developed flow meter specifications, the calibration tests, the description of the proposed off-line methodology and the results of the validation test carried out in a chassis dynamometer, where the validity of the mass flow meter and the methodology developed are demonstrated.

Direct isolation of human transcribed sequences from yeast artificial chromosomes through the application of RNA fingerprinting

The identification of cDNA clones from genomic regions known to contain human genes is usually the rate-limiting factor in positional cloning strategies. We demonstrate here that human genes present on yeast artificial chromosomes (YACs) are transcribed in yeast host cells. We have used the arbitrarily primed RNA (RAP) fingerprinting method to identify human-specific, transcribed sequences from YACs located in the 13q12 chromosome region. By comparing the RAP fingerprints generated using defined, arbitrary primers from various fragmented YACs, megaYACs, and host yeast, we were able to identify and map 20 products transcribed from the human YAC inserts. This method, therefore, permits the simultaneous isolation and mapping of novel expressed sequences directly from whole YACs.

Mutation rate varies among alleles at a microsatellite locus: Phylogenetic evidence

The understanding of the mutational mechanism that generates high levels of variation at microsatellite loci lags far behind the application of these genetic markers. A phylogenetic approach was developed to study the pattern and rate of mutations at a dinucleotide microsatellite locus tightly linked to HLA-DQB1 (DQCAR). A random Japanese population (n = 129) and a collection of multiethnic samples (n = 941) were typed at the DQB1 and DQCAR loci. The phylogeny of DQB1 alleles was then reconstructed and DQCAR alleles were superimposed onto the phylogeny. This approach allowed us to group DQCAR alleles that share a common ancestor. The results indicated that the DQCAR mutation rate varies drastically among alleles within this single microsatellite locus. Some DQCAR alleles never mutated during a long period of evolutionary time. Sequencing of representative DQCAR alleles showed that these alleles lost their ability to mutate because of nucleotide substitutions that shorten the length of uninterrupted CA repeat arrays; in contrast, all mutating alleles had relatively longer perfect CA repeat sequences.

A calcium influx is triggered and propagates in the zygote as a wavefront during in vitro fertilization of flowering plants

In this paper, we report direct measurement of an influx of extracellular Ca2+ induced by gamete fusion in flowering plants. This result was obtained during maize in vitro fertilization with the use of an extracellular Ca2+-selective vibrating probe. Ca2+ influx recorded at the surface of isolated egg cells, with or without adhesion of a male sperm cell, was close to zero and stable over time. Gamete fusion, however, triggered a Ca2+ influx in the vicinity of the sperm entry site with a delay of 1.8 ± 0.6 sec. The Ca2+ influx spread subsequently through the whole egg cell plasma membrane as a wavefront, progressing at an estimated rate of 1.13 μm⋅sec−1. Once established, Ca2+ influx intensities were sustained, monotonic and homogeneous over the whole egg cell, with an average peak influx of 14.92 pmol⋅cm−2⋅sec−1 and an average duration of 24.4 min. The wavefront spread of channel activation correlates well with the cytological modifications induced by fertilization, such as egg cell contraction, and with the cytosolic Ca2+ (c[Ca2+]) elevation previously reported. Calcium influx was inhibited effectively by gadolinium, possibly implicating mechanosensitive channels. Furthermore, artificial influxes created by incubation with Ca2+ ionophores mimicked some aspects of egg activation. Taken together, these results suggest that, during fertilization in higher plants, gamete membrane fusion starts the first embryonic events by channel opening and Ca2+ influx. In turn, c[Ca2+] may work as a trigger and possibly a space and time coordinator of many aspects of egg activation.

Impact of artifact correction methods on R-R interbeat signals to quantifying heart rate variability (HRV) according to linear and nonlinear methods.

In the analysis of heart rate variability (HRV) are used temporal series that contains the distances between successive heartbeats in order to assess autonomic regulation of the cardiovascular system. These series are obtained from the electrocardiogram (ECG) signal analysis, which can be affected by different types of artifacts leading to incorrect interpretations in the analysis of the HRV signals. Classic approach to deal with these artifacts implies the use of correction methods, some of them based on interpolation, substitution or statistical techniques. However, there are few studies that shows the accuracy and performance of these correction methods on real HRV signals. This study aims to determine the performance of some linear and non-linear correction methods on HRV signals with induced artefacts by quantification of its linear and nonlinear HRV parameters. As part of the methodology, ECG signals of rats measured using the technique of telemetry were used to generate real heart rate variability signals without any error. In these series were simulated missing points (beats) in different quantities in order to emulate a real experimental situation as accurately as possible. In order to compare recovering efficiency, deletion (DEL), linear interpolation (LI), cubic spline interpolation (CI), moving average window (MAW) and nonlinear predictive interpolation (NPI) were used as correction methods for the series with induced artifacts. The accuracy of each correction method was known through the results obtained after the measurement of the mean value of the series (AVNN), standard deviation (SDNN), root mean square error of the differences between successive heartbeats (RMSSD), Lomb\'s periodogram (LSP), Detrended Fluctuation Analysis (DFA), multiscale entropy (MSE) and symbolic dynamics (SD) on each HRV signal with and without artifacts. The results show that, at low levels of missing points the performance of all correction techniques are very similar with very close values for each HRV parameter. However, at higher levels of losses only the NPI method allows to obtain HRV parameters with low error values and low quantity of significant differences in comparison to the values calculated for the same signals without the presence of missing points.

Use efficiency of controlled release fertilizer on the growth of croton and petunia and N loss by leaching

The market of flowers and ornamentals such as croton (Codiaeum variegatum) and petunia (Petunia×hybrida Vilm.-Andr) have been created new technologies to constantly development, as one of the most promising segments of horticulture. Fertilization providing adequate nutrition and less leaching to the environment is the objective of numerous studies around the world. Therefore, two studies were conducted to evaluate the use of controlled release fertilizer (CRF) on the growth of two ornamental species, and N loss by leaching. The first experiment aim to evaluate sources and rates of CRF and water soluble fertilizer (WSF) on croton growth and nitrogen concentration on drained solution. Results showed that treatments with WSF and low rates of CRF provided higher plants growth, and the amount of N leached was higher for WSF treatments. The second experiment objective to compare plant performance and cost for strategies that potentially provide adequate nutrition during both the production and consumer phases for container-grown Petunia plants. In addition, two experiments were conducted to evaluate nutrient release in sand containers inside of the greenhouse and under controlled temperature conditions without plants. Results showed that during production phase all fertilizer treatments produced high quality plants, and during consumer phase, plants grown with WSF only during the production phase were nutrient-deficient, while plants receiving CRFs were still growing vigorously, especially in a high rate. The release rates of all CRF products were temperature-dependent. In conclusion CRF provided plant growth at the same rate that WSF, with less N leaching and extra cost less than U$0.065 per plant with CRF during production.