Sviluppo e applicazione di nuovi criteri per la verifica a fatica multiassiale di componenti strutturali in leghe di acciaio e alluminio

La presente Tesi ha per oggetto lo sviluppo e la validazione di nuovi criteri per la verifica a fatica multiassiale di componenti strutturali metallici . In particolare, i nuovi criteri formulati risultano applicabili a componenti metallici, soggetti ad un’ampia gamma di configurazioni di carico: carichi multiassiali variabili nel tempo, in modo ciclico e random, per alto e basso/medio numero di cicli di carico. Tali criteri costituiscono un utile strumento nell’ambito della valutazione della resistenza/vita a fatica di elementi strutturali metallici, essendo di semplice implementazione, e richiedendo tempi di calcolo piuttosto modesti. Nel primo Capitolo vengono presentate le problematiche relative alla fatica multiassiale, introducendo alcuni aspetti teorici utili a descrivere il meccanismo di danneggiamento a fatica (propagazione della fessura e frattura finale) di componenti strutturali metallici soggetti a carichi variabili nel tempo. Vengono poi presentati i diversi approcci disponibili in letteratura per la verifica a fatica multiassiale di tali componenti, con particolare attenzione all'approccio del piano critico. Infine, vengono definite le grandezze ingegneristiche correlate al piano critico, utilizzate nella progettazione a fatica in presenza di carichi multiassiali ciclici per alto e basso/medio numero di cicli di carico. Il secondo Capitolo è dedicato allo sviluppo di un nuovo criterio per la valutazione della resistenza a fatica di elementi strutturali metallici soggetti a carichi multiassiali ciclici e alto numero di cicli. Il criterio risulta basato sull'approccio del piano critico ed è formulato in termini di tensioni. Lo sviluppo del criterio viene affrontato intervenendo in modo significativo su una precedente formulazione proposta da Carpinteri e collaboratori nel 2011. In particolare, il primo intervento riguarda la determinazione della giacitura del piano critico: nuove espressioni dell'angolo che lega la giacitura del piano critico a quella del piano di frattura vengono implementate nell'algoritmo del criterio. Il secondo intervento è relativo alla definizione dell'ampiezza della tensione tangenziale e un nuovo metodo, noto come Prismatic Hull (PH) method (di Araújo e collaboratori), viene implementato nell'algoritmo. L'affidabilità del criterio viene poi verificata impiegando numerosi dati di prove sperimentali disponibili in letteratura. Nel terzo Capitolo viene proposto un criterio di nuova formulazione per la valutazione della vita a fatica di elementi strutturali metallici soggetti a carichi multiassiali ciclici e basso/medio numero di cicli. Il criterio risulta basato sull'approccio del piano critico, ed è formulato in termini di deformazioni. In particolare, la formulazione proposta trae spunto, come impostazione generale, dal criterio di fatica multiassiale in regime di alto numero di cicli discusso nel secondo Capitolo. Poiché in presenza di deformazioni plastiche significative (come quelle caratterizzanti la fatica per basso/medio numero di cicli di carico) è necessario conoscere il valore del coefficiente efficace di Poisson del materiale, vengono impiegate tre differenti strategie. In particolare, tale coefficiente viene calcolato sia per via analitica, che per via numerica, che impiegando un valore costante frequentemente adottato in letteratura. Successivamente, per validarne l'affidabilità vengono impiegati numerosi dati di prove sperimentali disponibili in letteratura; i risultati numerici sono ottenuti al variare del valore del coefficiente efficace di Poisson. Inoltre, al fine di considerare i significativi gradienti tensionali che si verificano in presenza di discontinuità geometriche, come gli intagli, il criterio viene anche esteso al caso dei componenti strutturali intagliati. Il criterio, riformulato implementando il concetto del volume di controllo proposto da Lazzarin e collaboratori, viene utilizzato per stimare la vita a fatica di provini con un severo intaglio a V, realizzati in lega di titanio grado 5. Il quarto Capitolo è rivolto allo sviluppo di un nuovo criterio per la valutazione del danno a fatica di elementi strutturali metallici soggetti a carichi multiassiali random e alto numero di cicli. Il criterio risulta basato sull'approccio del piano critico ed è formulato nel dominio della frequenza. Lo sviluppo del criterio viene affrontato intervenendo in modo significativo su una precedente formulazione proposta da Carpinteri e collaboratori nel 2014. In particolare, l’intervento riguarda la determinazione della giacitura del piano critico, e nuove espressioni dell'angolo che lega la giacitura del piano critico con quella del piano di frattura vengono implementate nell'algoritmo del criterio. Infine, l’affidabilità del criterio viene verificata impiegando numerosi dati di prove sperimentali disponibili in letteratura.

EFEITOS DOS APARELHOS TWIN FORCE BITE CORRECTOR E FORSUS FATIGUE RESISTANT DEVICE NA JUNÇÃO TEMPOROMANDIBULAR E NAS VIAS AÉREAS

O objetivo deste estudo prospectivo foi verificar os efeitos dos aparelhos Twin Force Bite Corrector e Forsus Fatigue Resistant Device na junção temporomandibular e nas vias aéreas. Para tanto, foram selecionados 21 pacientes adultos jovens, má oclusão de Classe II 1ª. divisão, bilateral, mínimo de 1/2 Classe II, padrão de crescimento horizontal. Para tanto, a amostra foi dividida em 2 grupos: grupo A, com média de idade inicial de 14,55 anos, tratado com o aparelho ortopédico fixo Twin ForceR por um período médio de 3,7 meses e o grupo B com média de idade inicial de 15,45 anos, tratado com o aparelho Forsus, por um período médio de 7,4 meses, ambos associados à aparelhagem fixa com mecânica straight-wire, prescrição MBT. Os pacientes do grupo A realizaram TCFC em três tempos: T1A (inicial - sem instalação do aparelho), T2A (no dia da i nstalação do aparelho ortopédico fixo), T3A (após a remoção do aparelho ortopédico fixo). Já o grupo 2 realizou TCFC em dois tempos: T2B (no dia da instalação do aparelho ortopédico fixo) e T3B (após a remoção do aparelho ForsusTM). Após a obtenção das imagens 3Dforam realizados cortes sagitais e coronais na ATM para avaliação do tamanho do côndilo e avaliação dos espaços articulares e vias aéreas. Para comparação intergrupos foi utilizado o teste "t" independente e correlação de Pearson e para comparação intragrupos, análise de variância a um critério e teste t pareado. O nível de significância adotado foi de p<0,05%. Não houve alteração significante na avaliação intergrupos, para as dimensões condilares, espaços articulares, e vias aéreas. Por outro lado, na avaliação intragrupo, houve alteração significante no comprimento efetivo da mandíbula (Co-Gn) para o grupo B, supostamente devido a um maior tempo de tratamento, pois houve correlação significante da largura coronal esquerda e direita com Co-Gn, embora clinicamente tenha sido irrelevante. Sendo assim, conclui-se que não houve diferença entre o desempenho dos dois aparelhos estudados na remodelação óssea condilar em pacientes jovens adultos e não houve alteração das vias aéreas após o tratamento com os aparelhos ortopédicos funcionais fixos e Forsus e Twin Force.

BEM-ESTAR SUBJETIVO E AUTOEFICÁCIA EM DEPENDENTES DE COCAÍNA/CRACK

Este estudo teve por objetivo identificar e descrever associações entre bem-estar subjetivo, construto formado por satisfação geral com a vida e afetos positivos e negativos,e autoeficáciapara abstinência de drogas em dependentes de cocaína/crack em processo de abstinência. Utilizou, para avaliar as variáveis, as Escalas de Afetos Positivos e Negativos, de Satisfação Geral com a Vida, de Autoeficácia para Abstinência de Drogas, de Avaliação para Mudança da Universidade de Rhode Island e um questionário de dados sócio-demográficos e socioculturais. Participaram 70 homens, dependentes de cocaína/crack, jovens e de baixa escolaridade.Eram pessoas de rendimentos de até três salários mínimos (63%), que foram internadas mais de uma vez (65%), autodeclaradas abstinentes no momento da coleta dos dados. Os participantes possuíam níveis médiosde autoeficácia para abstinência de drogas, níveis baixos de bem-estar subjetivo, e estavam satisfeitos com suas vidas. Cálculos de correlação de Pearson revelaram que não há associação entre bem-estar subjetivoe autoeficácia para abstinência de drogas, entre prontidão para mudança no consumo de drogas e bem-estar subjetivo, nem entre prontidão para mudança no consumo de drogas eautoeficácia para abstinência de drogas. Resultados de análise de variância revelaram que não houve diferençasnos níveis de bem-estar subjetivo entreos diferentes os agrupamentos de prontidão para mudanças nem entre as médias de autoeficácia para abstinência de drogas entre os diferentes agrupamentos de prontidão para mudanças no consumo de drogas. A discussão abordou os resultados diante do fato de a internação dos participantes ter sido involuntária ou voluntária, do tempo de internação, do seu estágio de prontidão para mudar seu comportamento de consumo de drogas e das características de seu grupo de abstinência diante da literatura da área. Finalmente, apontou, em conclusão, limitações e agenda de pesquisa futura.

Synthesis and expression of a gene encoding a 48-residue repeat in the Pseudomonas syringae ice nucleation protein

The aim of this work was to construct short analogues of the repetitive water-binding domain of the Pseudomonas syringae ice nucleation protein, InaZ. Structural analysis of these analogues might provide data pertaining to the protein-water contacts that underlie ice nucleation. An artificial gene coding for a 48-mer repeat sequence from InaZ was synthesized from four oligodeoxyribonucleotides and ligated into the expression vector, pGEX2T. The recombinant vector was cloned in Escherichia coli and a glutathione S-transferase fusion protein obtained. This fusion protein displayed a low level of ice-nucleating activity when tested by a droplet freezing assay. The fusion protein could be cleaved with thrombin, providing a means for future recovery of the 48-mer peptide in amounts suitable for structural analysis by nuclear magnetic resonance spectroscopy.

The fatigue ageing of vulcanised rubbers

The cause of the respective rough and smooth fatigue failure surfaces of Neoprene GS : Neoprene W and Neoprene GS : natural rubber vulcanisates is investigated. The contrasting morphology of the vulcanisates is found to be the major factor determining the fatigue behaviour of the blends. Neoprene GS and Neoprene W appear to form homogeneous blends which exhibit physical properties and fatigue failure surfaces intermediate between those of the two horropolymers. Neoprene GS and natural rubber exhibit heterogeneity when blended together. The morphology of these blends is found to influence both the fatigue resistance and failure surface of the vulcanisates. Exceptional uncut and cut initiated fatigue lives are observed for blends having an interconnecting network morphology. The network structure and cross-link density of the elastomers in the blends and the addition of carbon black and antioxidant are all found to influence the fatigue resistance but not the failure mechanism of the vulcanisate.

Fatigue in rubber vulcanisates

A study has been made of the effect of single extensions and continuous fatigue on the structures of various natural rubber networks. The change in network structure of a conventional vulcanisate on a single extension manifests itself as permanent set. The change in network structure has been assessed by the use of the chemical probes, propan-2-thiol/piperidine, hexane-thiol/piperidine and triphenyl phosphine, which determine the polysulphide and disulphide crosslink densities and main chain modification respectively. The permanent set induced on a single extension of a conventional sulphur vulcanisate has been shown to result from the destruction and reformation of polysulphide crosslinks. The magnitude of the effect was dependent upon the degree of extension and showed a maximum at extensions corresponding to the onset of stress-induced crystallisation. The incorporation of a reinforcing filler, HAF-carbon black, magnified the effect. Vulcanisates that possessed only mono and disulphide crosslinks did not show any significant permanent set. The continuous changes in network structure during fatigue have also been determined, and the effects of carbon black and antioxidants on these changes and the fatigue life have been assessed. During fatigue the overall crosslink density increased slightly, which resulted from the destruction of polysulphide crosslinks. and their replacement by principally disulphide crosslinks. Antioxidants reduced the rate of destruction of polysulphide crosslinks and increased the fatigue life of the rubber network. The fatigue life of the network also depended upon the concentration of free chain ends. These chain ends were incorporated into the network by masticating rubber under nitrogen in the presence of bis (diisopropyl)thiophosphoryl disulphide, which improved the fatigue resistance by up to 9%.

The fatigue properties of pressure diecast zinc-aluminium based alloys

The fatigue behaviour of the cold chamber pressure-die-cast alloys: Mazak3, ZA8, ZA27, M3K, ZA8K, ZA27K, K1, K2 and K3 was investigated at temperature of 20°C. The alloys M3K, ZA8K and ZA27K were also examined at temperatures of 50 and 100°C. The ratio between fatigue strength and tensile strength was established at 20°C at 107 cycles. The fatigue life prediction of the alloys M3K, ZA8K and ZA27K was formulated at 20, 50 and 100°C. The prediction formulae were found to be reasonably accurate. All of the experimental alloys were heterogeneous and contained large but varying amounts of pores. These pores were a major contribution and dominated the alloys fatigue failure. Their effect, however, on tensile failure was negligible. The ZA27K possessed the highest tensile strength but the lowest fatigue strength. The relationship between the fracture topography and the microstructure was also determined by the use of a mixed signal of a secondary electron and a back-scattered electron on the SEM. The tensile strength of the experimental alloys was directly proportional to the aluminium content within the alloys. The effect of copper content was also investigated within the alloys K1, K2, ZA8K and K3 which contained 0%, 0.5%, 1.0% and 2.0% respectively. It was determined that the fatigue and tensile strengths improved with higher copper contents. Upon ageing the alloys Mazak3, ZA8 and ZA27 at an ambient temperature for 5 years, copper was also found to influence and maintain the metastable Zn-Al (αm) phase. The copper free Mazak3 upon ageing lost this metastable phase. The 1.0% copper ZA8 alloy had lost almost 50% of its metastable phase. Finally the 2.0% copper ZA27 had merely lost 10% of its metastable phase. The cph zinc contained a limited number of slip systems, therefore twinning deformation was unavoidable in both fatigue and tensile testing.

A novel detection method for determining a surgeon's fatigue and hand tremor

The thesis presents new methodology and algorithms that can be used to analyse and measure the hand tremor and fatigue of surgeons while performing surgery. This will assist them in deriving useful information about their fatigue levels, and make them aware of the changes in their tool point accuracies. This thesis proposes that muscular changes of surgeons, which occur through a day of operating, can be monitored using Electromyography (EMG) signals. The multi-channel EMG signals are measured at different muscles in the upper arm of surgeons. The dependence of EMG signals has been examined to test the hypothesis that EMG signals are coupled with and dependent on each other. The results demonstrated that EMG signals collected from different channels while mimicking an operating posture are independent. Consequently, single channel fatigue analysis has been performed. In measuring hand tremor, a new method for determining the maximum tremor amplitude using Principal Component Analysis (PCA) and a new technique to detrend acceleration signals using Empirical Mode Decomposition algorithm were introduced. This tremor determination method is more representative for surgeons and it is suggested as an alternative fatigue measure. This was combined with the complexity analysis method, and applied to surgically captured data to determine if operating has an effect on a surgeon’s fatigue and tremor levels. It was found that surgical tremor and fatigue are developed throughout a day of operating and that this could be determined based solely on their initial values. Finally, several Nonlinear AutoRegressive with eXogenous inputs (NARX) neural networks were evaluated. The results suggest that it is possible to monitor surgeon tremor variations during surgery from their EMG fatigue measurements.

"Crack down on the celebrity junkies": does media coverage of celebrity drug use pose a risk to young people?

This study analysed news media content to examine the role played by celebrity drug use in young people's perceptions of drug use. We know that young people have access to discourses of drug use through music and other media which may emphasise short term gains (of pleasure or sexual success) over longer term health and social problems. This study goes beyond a simple modelling approach by using Media Framing Analysis (MFA) to take an in-depth look at the messages themselves and how they are 'framed'. New stories about Amy Winehouse's drug use were used and we conducted focus groups with young people asking them questions about drugs, celebrity and the media. Frames identified include: 'troubled genius', 'losing patience' and 'glamorization or gritty realism'. Initially, the press championed Winehouse's musical talent but soon began to tire of her recklessness; the participants tended to be unimpressed with Winehouse's drug use, characterising her as a promising artist who had 'gone off the rails'. Young people were far more critical of Winehouse than might be expected, demonstrating that concerns about the influence of celebrity drug use and its impact on future health risk behaviour among young people may have been over-simplified and exaggerated. This study illustrates the need to understand young people and their frames of reference within popular culture when designing drug awareness information relevant to them. Furthermore, it indicates that critical media skills analysis may contribute to health risk education programmes related to drug use.

The durability of glass fibre reinforced cements made with new cementitious matrices

Widespread use of glass fibre reinforced cement (GRC) has been impeded by concerns over its durability. Three degradation mechanisms are proposed - fibre corrosion, Ca(OHh precipitation and matrix densification - although their relative importance is debated. Matrices with reduced alkalinities and Ca(OH)2 contents are being developed; the aim of this study was to investigate their hydration and interaction with alkali-resistant fibres to determine the factors controlling their long-term durability, and assess the relevancy of accelerated ageing. The matrices studied were: OPC/calcium-sulphoaluminate cement plus metakaolin (C); OPC plus metakaolin (M); blast-furnace slag cement plus a micro-silica based additive (D); and OPC (O). Accelerated ageing included hot water and cyclic regimes prior to tensile testing. Investigations included pore solution expression, XRD, DTA/TG, SEM and optical petrography. Bond strength was determined from crack spacings using microstructural parameters obtained from a unique image analysis technique. It was found that, for the new matrices - pore solution alkalinities were lower; Ca(OH)2 was absent or quickly consumed; different hydrates were formed at higher immersion temperatures; degradation under 65°C immersion was an order of magnitude slower, and no interfilamental Ca(OH)2 was observed .It was concluded that: fibre weakening caused by flaw growth was the primary degradation mechanism and was successfully modelled on stress corrosion/static fatigue principles. OPC inferiority was attributed partly to its higher alkalinity but chiefly to the growth of Ca(OH)2 aggravating the degradation; and hot water ageing although useful in model formulation and contrasting the matrices, changed the intrinsic nature of the composites rather than simply accelerating the degradation mechanisms.

The mechanics of creep crack growth in a Magnox alloy

Magnox AL80 has been used for a study of creep crack propagation. A number of variables have been considered such as specimen geometry,notch root radius, material thickness, creep prestrain and stress level.The work has covered the material behaving under two values of the creep exponent, n=3.5 and n=7, according to the stress level. As well as observing initiation times and crack growth rates, scribed grids have been used to examine the near crack tip strain levels and distributions. It was shown that estimations of COD from notch flank opening can give misleading indications of material behaviour and that a more informative method was to monitor displacements in the material surrounding the crack tip. Strong evidence was found for crack advance being displacement controlled, however it was shown that the COD approach should be considered geometry dependant. The summation of ∈xx and ∈yy provided the most successful description of crack advance as it produced a single value that described propagation in all the cases concidered. The strain distributions indicates that σyy was related to distance from a point ahead of the crack tip by the exponent - (l/n+l) and that σxx is proportional to σyy. The constraint stresses arising in the DEN and CN specimens were evaluated. Initiation time was found to be principally affected by the stress level but was modified by the constraints arising from specimen geometry. Crack growth was found not to obey either the empirical K or σpett relationships but was reviewed in context of the observed strain behaviour.

Creep crack growth in cast steam turbine casing steels

The creep rupture properties of cast ½Cr½Mo¼V and 1Cr1Mo¼V alloy steel used in the manufacture of power station steam generating plant. have been investigated. The effects of constraint and geometry on the creep rupture properties are also considered. The validity of various criteria controlling macroscopic creep crack growth in cast CrMoV alloys has been examined. It is found that neither the stress intensity factor nor reference stress correlate satisfactorily the creep crack growth rates at the test temperature of 550°C. Certain minimum displacements must be achieved for crack initiation and propagation. It is found that this displacement as measured by crack opening displacement or crack aspect ratio, is the same in both compact tension and centre-cracked panel geometries, is invariant with crack length and decreases with increasing constraint. The effect of constraint on creep crack growth rate in the two geometries is less conclusive. A new model describing creep crack growth in cast CrMoV alloy steels has been developed. The model is based on the results from a numerical finite element creep analysis of the relaxation and redistribution of stress ahead of an incubating creep crack . It is found that macroscopic creep crack growth in a material undergoing either plane stress or plane strain deformation can be described by a fracture stress which is based on the Von Mises equivalent stress. It has been shown that this model is capable of rationalising all of the experimental crack velocity data from the cast CrMoV alloys. The resultant degree of data correlation is far superior to that obtained when using the stress intensity factor or reference stress. A cumulative damage creep fracture model based upon the results from the numerical analysis has been developed. It is found that the model is capable of predicting the behaviour of propagating creep cracks in cast CrMoV alloys from smooth bar creep rupture data.