Development of an autonomous unmanned aerial system to collect time-stamped samples from the atmosphere and localize potential pathogen sources

This paper presents the hardware development and testing of a new concept for air sampling via the integration of a prototype spore trap onboard an unmanned aerial system (UAS).We propose the integration of a prototype spore trap onboard a UAS to allow multiple capture of spores of pathogens in single remote locations at high or low altitude, otherwise not possible with stationary sampling devices.We also demonstrate the capability of this system for the capture of multiple time-stamped samples during a single mission.Wind tunnel testing was followed by simulation, and flight testing was conducted to measure and quantify the spread during simulated airborne air sampling operations. During autonomous operations, the onboard autopilot commands the servo to rotate the sampling device to a new indexed location once the UAS vehicle reaches the predefined waypoint or set of waypoints (which represents the region of interest). Time-stamped UAS data are continuously logged during the flight to assist with analysis of the particles collected. Testing and validation of the autopilot and spore trap integration, functionality, and performance is described. These tools may enhance the ability to detect new incursions of spores

An advanced meshless method for time fractional diffusion equation

Recently, because of the new developments in sustainable engineering and renewable energy, which are usually governed by a series of fractional partial differential equations (FPDEs), the numerical modelling and simulation for fractional calculus are attracting more and more attention from researchers. The current dominant numerical method for modeling FPDE is Finite Difference Method (FDM), which is based on a pre-defined grid leading to inherited issues or shortcomings including difficulty in simulation of problems with the complex problem domain and in using irregularly distributed nodes. Because of its distinguished advantages, the meshless method has good potential in simulation of FPDEs. This paper aims to develop an implicit meshless collocation technique for FPDE. The discrete system of FPDEs is obtained by using the meshless shape functions and the meshless collocation formulation. The stability and convergence of this meshless approach are investigated theoretically and numerically. The numerical examples with regular and irregular nodal distributions are used to validate and investigate accuracy and efficiency of the newly developed meshless formulation. It is concluded that the present meshless formulation is very effective for the modeling and simulation of fractional partial differential equations.

A node-based smoothed conforming point interpolation method (NS-CPIM) for elasticity problems

This paper formulates a node-based smoothed conforming point interpolation method (NS-CPIM) for solid mechanics. In the proposed NS-CPIM, the higher order conforming PIM shape functions (CPIM) have been constructed to produce a continuous and piecewise quadratic displacement field over the whole problem domain, whereby the smoothed strain field was obtained through smoothing operation over each smoothing domain associated with domain nodes. The smoothed Galerkin weak form was then developed to create the discretized system equations. Numerical studies have demonstrated the following good properties: NS-CPIM (1) can pass both standard and quadratic patch test; (2) provides an upper bound of strain energy; (3) avoid the volumetric locking; (4) provides the higher accuracy than those in the node-based smoothed schemes of the original PIMs.

Quality management system and construction performance

This paper discusses the level of effectiveness of quality principles and quality management system implementation and the relationship with performance of ISO9000 certified Indonesian contractors. It also discusses the statistical relationship between quality management systems (QMSs) and key performance indicators (KPIs) amongst a large sample of Indonesian construction companies. Data collected is from questionnaire surveys involving Quality Managers, Managers, and Project and Site Engineers representing 77 different companies. Results indicate that even though some contractors have not yet effectively implemented an effective QMS, most of the KPIs of respondent companies are still at the level of high performance. The statistical results show that the relationship between variables of ISO9000 QMS principles and contractors’ KPIs is significant. These results suggest that an increment in the implementation level of QMS principles can increase KPIs, however that much effort is still required for Indonesian contractors to fully effectively implement QMS principles and thus substantially improve performance against KPIs.

Private supervisors of learner drivers and Queensland's graduated driver licensing system : how important are they?

Background: A key element of graduated driver licensing systems is the level of support provided by parents. In mid-2007 changes were made to Queensland’s graduated driver licensing system, including amendments to the learner licence with one of the more significant changes requiring learners to record 100 hours of supervised driving practice in a logbook. Prior to mid-2007, there was no minimum supervision requirement. Aims: The aim of this study was to document the experiences of the supervisors of Queensland learner drivers after the changes made to the graduated driver licensing system in mid-2007. Methods: The sample of 552 supervisors of learner drivers was recruited using a combination of convenience and snowball sampling techniques. The internet survey was open for completion between July 2009 and May 2010 and took approximately 15 to 20 minutes for participants to complete. Results: For 59.7 per cent of the participants, this was the first time that they had supervised a learner driver. For 63.2 per cent, they classified themselves as the main supervisor for the learner driver. Participants provided an average of 79.62 hours of supervision (sd = 92.38), while other private supervisors provided 34.89 hours of supervision (sd = 41.74) to the same learner and professional driving instructors 18.55 hours of supervision (sd = 27.54). The vast majority of supervisors recorded all or most of the practice that they provided their learner driver in their log book with most supervisors indicating that they believed that the hours recorded in the learner’s logbook were either accurate or very accurate. While many supervisors stated that they did not receive any advice regarding the supervision of learner drivers, some had received advice from others such as friends or through discussions with a professional driving instructor. Discussion and conclusions: While graduated driver licensing systems implicitly encourage the involvement of parents and other private supervisors, these people tend not to be systematically involved. As demonstrated in this study, private supervisors provide a significant amount of supervised practice and seek to record this practice accurately and honestly in the learner’s logbook. However, even though a significant number of participants reported that this was the first time that they had supervised a learner driver, they accessed little support or guidance for their role. This suggests a need to more overtly encourage and support the role of private supervisors for learner drivers.

Locating 'Agency' Within Ubiquitous Computing Systems

The final shape of the "Internet of Things" ubiquitous computing promises relies on a cybernetic system of inputs (in the form of sensory information), computation or decision making (based on the prefiguration of rules, contexts, and user-generated or defined metadata), and outputs (associated action from ubiquitous computing devices). My interest in this paper lies in the computational intelligences that suture these positions together, and how positioning these intelligences as autonomous agents extends the dialogue between human-users and ubiquitous computing technology. Drawing specifically on the scenarios surrounding the employment of ubiquitous computing within aged care, I argue that agency is something that cannot be traded without serious consideration of the associated ethics.

Reactive image-based collision avoidance system for unmanned aircraft systems

Approximately 20 years have passed now since the NTSB issued its original recommendation to expedite development, certification and production of low-cost proximity warning and conflict detection systems for general aviation [1]. While some systems are in place (TCAS [2]), ¡¨see-and-avoid¡¨ remains the primary means of separation between light aircrafts sharing the national airspace. The requirement for a collision avoidance or sense-and-avoid capability onboard unmanned aircraft has been identified by leading government, industry and regulatory bodies as one of the most significant challenges facing the routine operation of unmanned aerial systems (UAS) in the national airspace system (NAS) [3, 4]. In this thesis, we propose and develop a novel image-based collision avoidance system to detect and avoid an upcoming conflict scenario (with an intruder) without first estimating or filtering range. The proposed collision avoidance system (CAS) uses relative bearing ƒÛ and angular-area subtended ƒê , estimated from an image, to form a test statistic AS C . This test statistic is used in a thresholding technique to decide if a conflict scenario is imminent. If deemed necessary, the system will command the aircraft to perform a manoeuvre based on ƒÛ and constrained by the CAS sensor field-of-view. Through the use of a simulation environment where the UAS is mathematically modelled and a flight controller developed, we show that using Monte Carlo simulations a probability of a Mid Air Collision (MAC) MAC RR or a Near Mid Air Collision (NMAC) RiskRatio can be estimated. We also show the performance gain this system has over a simplified version (bearings-only ƒÛ ). This performance gain is demonstrated in the form of a standard operating characteristic curve. Finally, it is shown that the proposed CAS performs at a level comparable to current manned aviations equivalent level of safety (ELOS) expectations for Class E airspace. In some cases, the CAS may be oversensitive in manoeuvring the owncraft when not necessary, but this constitutes a more conservative and therefore safer, flying procedures in most instances.

Towards an automatic system for road lane marking extraction in large-scale aerial images acquired over rural areas by hierarchical image analysis and Gabor filter

An automatic approach to road lane marking extraction from high-resolution aerial images is proposed, which can automatically detect the road surfaces in rural areas based on hierarchical image analysis. The procedure is facilitated by the road centrelines obtained from low-resolution images. The lane markings are further extracted on the generated road surfaces with 2D Gabor filters. The proposed method is applied on the aerial images of the Bruce Highway around Gympie, Queensland. Evaluation of the generated road surfaces and lane markings using four representative test fields has validated the proposed method.

Scene invariant crowd counting and crowd occupancy analysis

In public places, crowd size may be an indicator of congestion, delay, instability, or of abnormal events, such as a fight, riot or emergency. Crowd related information can also provide important business intelligence such as the distribution of people throughout spaces, throughput rates, and local densities. A major drawback of many crowd counting approaches is their reliance on large numbers of holistic features, training data requirements of hundreds or thousands of frames per camera, and that each camera must be trained separately. This makes deployment in large multi-camera environments such as shopping centres very costly and difficult. In this chapter, we present a novel scene-invariant crowd counting algorithm that uses local features to monitor crowd size. The use of local features allows the proposed algorithm to calculate local occupancy statistics, scale to conditions which are unseen in the training data, and be trained on significantly less data. Scene invariance is achieved through the use of camera calibration, allowing the system to be trained on one or more viewpoints and then deployed on any number of new cameras for testing without further training. A pre-trained system could then be used as a ‘turn-key’ solution for crowd counting across a wide range of environments, eliminating many of the costly barriers to deployment which currently exist.

An enriched radial point interpolation method based on weak-form and strong-form

In this article, an enriched radial point interpolation method (e-RPIM) is developed for computational mechanics. The conventional radial basis function (RBF) interpolation is novelly augmented by the suitable basis functions to reflect the natural properties of deformation. The performance of the enriched meshless RBF shape functions is first investigated using the surface fitting. The surface fitting results have proven that, compared with the conventional RBF, the enriched RBF interpolation has a much better accuracy to fit a complex surface than the conventional RBF interpolation. It has proven that the enriched RBF shape function will not only possess all advantages of the conventional RBF interpolation, but also can accurately reflect the deformation properties of problems. The system of equations for two-dimensional solids is then derived based on the enriched RBF shape function and both of the meshless strong-form and weak-form. A numerical example of a bar is presented to study the effectiveness and efficiency of e-RPIM. As an important application, the newly developed e-RPIM, which is augmented by selected trigonometric basis functions, is applied to crack problems. It has been demonstrated that the present e-RPIM is very accurate and stable for fracture mechanics problems.

The aesthetic system of entertainment

Entertainment Industries is the first book to map entertainment as a cultural system. Including work from world-renowned analysts such as Henry Jenkins and Jonathan Gray, this innovative collection explains what entertainment is and how it works. Entertainment is audience-centred culture. The Entertainment Industries are a uniquely interdisciplinary collection of evolving businesses that openly monitor evolving cultural trends and work within them. The producers of entertainment – central to that practice– are the new artists. They understand audiences and combine creative, business and legal skills in order to produce cultural products that cater to them. Entertainment Industries describes the characteristics of entertainment, the systems that produce it, and the role of producers and audiences in its development, as well as explaining the importance of this area of study, and how it might be better integrated into Universities.

Risky strategic behaviour : unintended consequences of good intentions in the homelessness service system

The delivery of human services occurs through a complex and often volatile system characterised by both competing and cooperating efforts. A recent strategic intention of government has been to integrate disparate service providers and programs into a more effective and efficient system using competitive funding regimes. A program of amalgamation has also been forecast and promoted as a further mechanism by which to link up smaller agencies thus creating economy and efficiency in the scale and scope of their service modes. Despite the current reliance on competitive funding models and amalgamation as the preferred ways forward for the sector little is known about their integrative capacity including their ability to predict outcomes and their consequences : the ‘unknown unknowns’. Drawing on an extensive data set of human services integration initiatives in Queensland, Australia, this paper examines the impact of government policy and service models and the risks arising from the tensions between competition and accountability on the one hand and the established good will and trust on the other. It is argued that unresolved, these tensions can lead to a weakening of the social infrastructure and make the system more vulnerable to inherent systemic risks. The paper finds that government’s efforts to externalise risk to the non-government sector leads to fragmentation of the service system and fractured collaborative capability. These unintended outcomes themselves have the unintended consequence of leaving governments disconnected from the service system and unable to provide the leadership role and direction necessary for sustained integration. Moreover, facilitating such a leadership role is undermined by behaviours that are directly contrary to collective integration models.