On-line measurement of soil properties without direct spectral response in near infrared spectral range

So far, the majority of reports on on-line measurement considered soil properties with direct spectral responses in near infrared spectroscopy (NIRS). This work reports on the results of on-line measurement of soil properties with indirect spectral responses, e.g. pH, cation exchange capacity (CEC), exchangeable calcium (Caex) and exchangeable magnesium (Mgex) in one field in Bedfordshire in the UK. The on-line sensor consisted of a subsoiler coupled with an AgroSpec mobile, fibre type, visible and near infrared (vis–NIR) spectrophotometer (tec5 Technology for Spectroscopy, Germany), with a measurement range 305–2200 nm to acquire soil spectra in diffuse reflectance mode. General calibration models for the studied soil properties were developed with a partial least squares regression (PLSR) with one-leave-out cross validation, using spectra measured under non-mobile laboratory conditions of 160 soil samples collected from different fields in four farms in Europe, namely, Czech Republic, Denmark, Netherland and UK. A group of 25 samples independent from the calibration set was used as independent validation set. Higher accuracy was obtained for laboratory scanning as compared to on-line scanning of the 25 independent samples. The prediction accuracy for the laboratory and on-line measurements was classified as excellent/very good for pH (RPD = 2.69 and 2.14 and r2 = 0.86 and 0.78, respectively), and moderately good for CEC (RPD = 1.77 and 1.61 and r2 = 0.68 and 0.62, respectively) and Mgex (RPD = 1.72 and 1.49 and r2 = 0.66 and 0.67, respectively). For Caex, very good accuracy was calculated for laboratory method (RPD = 2.19 and r2 = 0.86), as compared to the poor accuracy reported for the on-line method (RPD = 1.30 and r2 = 0.61). The ability of collecting large number of data points per field area (about 12,800 point per 21 ha) and the simultaneous analysis of several soil properties without direct spectral response in the NIR range at relatively high operational speed and appreciable accuracy, encourage the recommendation of the on-line measurement system for site specific fertilisation.

High Intensity Lasers Application to Advanced Materials Processing: Laser Peening and Related Processes

High Intensity Lasers Application to Advanced Materials Processing: Laser Peening and Related

Experimental validation of a fracture model for pearlitic steel bars based on the cohesive zone model

Congreso internacional celebrado en Praga sobre modelos numéricos de fractura en el campo de la ciencia de materiales y estructuras.

Experimental validation of a fracture model for pearlitic steel bars based on the cohesive zone model

Steel is, together with concrete, the most widely used material in civil engineering works. Not only its high strength, but also its ductility is of special interest, since it allows for more energy to be stored before failure. A better understanding of the material behaviour before failure may lead to better structural safety strategies.

Finite element simulation of sandwich panels of laminated plaster and rockwool under mixed mode fracture

Sandwich panels of laminated gypsum and rock wool have shown large pathology of cracking due to excessive slabs deflection. Currently the most widespread use of this material is as vertical elements of division or partition, with no structural function, what justifies that there are no studies on the mechanism of fracture and mechanical properties related to it. Therefore, and in order to reduce the cracking problem, it is necessary to progress in the simulation and prediction of the behaviour under tensile and shear load of such panels, although in typical applications have no structural responsability.

Cover cracking of the reinforced concrete due to rebar corrosion induced by chloride penetration

This paper is focused on the problem of the chloride-induced corrosion of the rebar in reinforced concrete, with special application to the slabs and decks of the bridges. High superficial concentrations may be usual in these structures (marine environments or de-icing salts in roadway bridges, e.g.). Like any aggressive agent such as water, gases or other dissolved ions, chloride induced deterioration is very conditioned by possibilities of transport through concrete mass.

What can we learn from voice therapy of the speaking voice for singers's voice?

Voice therapies of muscle tension dysphonia in Germany need to be increased in effectiveness by applying intensive, manualized procedures and standardized assessment protocols. The same holds true for therapies of disturbed singer's voices. According to a Cochrane review on the effectiveness of therapies of functional dysphonia neither direct nor indirect voice therapies alone but combinations of both elements are effective (Ruotsalainen et al., 2007).

An Implemented of a Real-Time Experimental Setup for Robotic Teleoperation System

The development of this work presents the implementation of an experimental platform, which will permit to investigate on a methodology for the design and analysis of a teleoperated system, considering the delay in the communication channel. The project has been developed in partnership with the laboratory of Automatic and Robotics of the Universidad Politécnica de Madrid and the Laboratory at the Centro de Tecnologías Avanzadas de Manufactura at the Pontificia Universidad Católica del Perú. The mechanical structure of the arm that is located in the remote side has been built and the electric servomechanism has been mounted to control their movement. The experimental test of the Teleoperation system has been developed. The PC104 card commands the power interface and sensors of the DC motor of each articulation of the arm. Has developed the drives for the management of the operations of the master and the slave: send/reception of position, speed, acceleration and current data through a CAN network. The programs for the interconnection through a LAN network, between the Windows Operating System and the Real-time Operating System (QNX), has been developed. The utility of the developed platform (hardware and software) has been demonstrated.

Development of a PWR-W and an AP1000® containment building 3D model with a CFD code for Best-Estimate Thermal-Hydraulic Analysis

The simulation of design basis accidents in a containment building is usually conducted with a lumped parameter model. The codes normally used by Westinghouse Electric Company (WEC) for that license analysis are WGOTHIC or COCO, which are suitable to provide an adequate estimation of the overall peak temperature and pressure of the containment. However, for the detailed study of the thermal-hydraulic behavior in every room and compartment of the containment building, it could be more convenient to model the containment with a more detailed 3D representation of the geometry of the whole building. The main objective of this project is to obtain a standard PWR Westinghouse as well as an AP1000® containment model for a CFD code to analyze the thermal-hydraulic detailed behavior during a design basis accident. In this paper the development and testing of both containment models is presented.

Qualitative operational value at risk for an electric utility based on the guidelines of the basel committee

This paper presents a model for determining value at operational risk ?OpVaR? in electric utilities, with the aim to confirm the versatility of the Bank for International Settlements (BIS) proposals. The model intends to open a new methodological approach in risk management, paying special attention to underlying operational sources of risk.

Estudio y validación experimental del efecto de aire interno en un perfil aerodinámico hueco

La presente investigación se llevó a cabo en la Universidad Politécnica de Madrid (España) conjuntamente con la Universidad Nacional Experimental del Táchira (Venezuela). El estudio consistió en diseñar una cavidad interna dentro del perfil aerodinámico 2415-3s, el cual fue desarrollado en la Universidad Técnica Checa (Praga, República Checa). Se realizó un estudio computacional, mediante la técnica del CFD, de diferentes modelos de cavidades internas en este perfil, para seleccionar el diseño más adecuado, fabricando un prototipo en 3D; logrando de esta manera validar la simulación computacional con los datos experimentales obtenidos con los ensayos en el túnel de viento AF6109 de la Universidad Nacional Experimental del Táchira. También se aplicaron técnicas de visualización en el túnel de viento, como líneas de corriente de humo y películas de aceite sobre el perfil aerodinámico. Dicho procedimiento permitió corroborar la validación de la simulación computacional. El perfil aerodinámico seleccionado se denominó 2415-3s-TC, cuya característica principal consiste en tres canales independientes entre sí, alojados dentro de la cavidad interna, permitiendo que el flujo de aire forzado a través de la cavidad, cambiara de dirección, para desembocar lo más tangencialmente, así como, lo más perpendicularmente posible al escalón del perfil aerodinámico 2415-3s. Esta configuración de diseñó permitió elevar el coeficiente de sustentación para ángulos de ataque mayores a 8º, así como para ángulos cercanos al ángulo crítico. ABSTRACT This research was conducted at the Polytechnic University of Madrid (Spain) together with the National Experimental University of Táchira (Venezuela). The study was to design an internal cavity within the airfoil 2415-3s, which was developed in the Czech Technical University (Prague, Czech Republic). A computational study was performed using CFD technique, different models of internal cavities in the profile to select the most appropriate design, manufacturing a prototype 3D; thus achieving validate the computer simulation with experimental data obtained from the tests in the wind tunnel AF6109 of the National Experimental University of Táchira. Visualization techniques were also applied in the wind tunnel, as streamlines smoke and oil films on the airfoil. This procedure corroborated validation of computational simulation. The airfoil selected denominated 2415-3s-TC, whose main characteristic consists of three independent channels each other, housed within the inner cavity, allowing the forced air flow through the cavity, change direction, to lead as more tangentially and, as perpendicular as possible to the step 2415-3s aerofoil. This configuration designed allowed increasing the lift coefficient for higher angles of attack to 8º, and for angles near the critical angle.

Networked Utopia : the Architecture and Urbanism of the Bata Shoe Company Satellite Cities = Utopia en red : arquitectura y urbanismo en las ciudades satélite de la Bata Shoe Company, 1930 al presente

From its humble beginnings as a small workshop established by Tomáš Baťa in 1874, the Bata Shoe Company became a gigantic concern in the 1920s, built on the principles of scientific management and welfare capitalism. The growth of the company engulfed Zlín (in today’s Czech Republic), its hometown, and transformed it into a modern industrial garden city satisfying the needs of both a growing industrial population, and those of the company itself. As a reaction to the aftermath of the crisis of 1929, the enterprise began a strategy of decentralization and international expansion characterized by the design and construction of a series of modern industrial towns that replicated the model of Zlín around the globe. This study is an exhaustive survey of these cities, their rationale, design, and their postindustrial conditions; it is a comparative work that has used field trips, photography, interviews, and archival material to explain the logics behind Bata’s project, to document the design and implementation of the model to multiple contexts and geographies, and to evaluate of the urban legacy of this undertaking. Finally, the research explores the question of what can the design disciplines, and other parties involved, learn from a full synthesis on the history and urbanism of the Bata satellite cities with regard to the re-imagination and sustainability of contemporary industry-sponsored interventions in developing geographies. RESUMEN Con origen en un humilde y pequeño taller fundado en 1874 por Tomáš Baťa, la Bata Shoe Company creció hasta convertirse en una gigantesca empresa en los anos 20, fundada en principios de control científico de la producción y capitalismo de bienestar. El crecimiento de la compañía se extendió por Zlín (en la actual República Checa), su pueblo de nacimiento, y la transformó en una moderna ciudad jardín industrial capaz de satisfacer las necesidades tanto de una población en alza como de la propia empresa. Como reacción a la crisis de 1929, Bata inició una estrategia de descentralización y expansión internacional caracterizada por el proyecto y construcción de modernas ciudades industriales que replicaron el modelo de Zlín por el mundo. Esta tesis es un estudio exhaustivo de estas ciudades: las razones detrás del proyecto, su diseño, y su condición post-industrial; es un estudio comparativo que se ha servido de trabajo de campo, documentación fotográfica, entrevistas y materiales de archivo para explicar la lógica detrás del proyecto de Bata, documentar el diseño e implementación de tal modelo en múltiples contextos y geografías, y valorar el legado urbano de esta empresa. Finalmente, la investigación evalúa qué podrían aprender las disciplinas del diseño y otras partes implicadas de una síntesis completa de la historia y el urbanismo de las ciudades satélite de Bata, en lo relativo a la reinvención y sostenibilidad de proyectos contemporáneos de la industria en geografías en desarrollo.

A Porposal: "Agro-ERASMUS"

The rural population is getting smaller as percentage of the total population in the countries. There is a constant depopulation of rural areas to urban areas. The most extreme data are in countries like USA, where the rural population is 1.5%, from which 1% of that amount is part time and only 0.5% full time. On the other side, we have countries with more than 50% rural population. Related to training, cultural development, business and specific weight in society, rural residents have no significance in their societies. As they are few, and separated across the territory they have no influence on their societies. Comparing the USA farmer with one from the EU, we see that the American one is a businessperson and the European one, in most cases is a farm worker. To reduce this gap between these different farmers, we believe that we must train the new generations of children belonging to farming Europe. They must have a common language, English; they must know other countries culture and farming systems, live and network with other young Europeans colleagues,future young farmers. It is what we have coined as AGRO-ERASMUS. A project to be placed within the EU Common Agriculture Policies. The project must be designed before its implementation. Even some previous experience should make better viability. It should make use of a network of agricultural universities in several European countries. Each university would build a "farm school" where young people would learn "English?, and visit and work in small agricultural practices with a correct use of the time. One important subject dealing with should be agribusiness. The procedure based on the ?Farm School? (F-S) experience, should start with young people from 13 years up to 18 years. Their attendance, every summer, to the F-S should be rotated between different countries besides their own. The first and second year, with young people 13/14 years old, the Farm School would last less than three weeks in an English speaking country (Ireland, UK or someone else). They should live with a local family the time they stay outside of the Farm School (F-S). This two years period must be devoted to learn and become familiar with the English language and cultural differences. The rest of the four years left, the Farm Schools will have longer duration and be placed in other countries from the network. The living way would be in multinational teams of young people where the only spoken language would be English. After six years of summer oexistence speaking English and learning new competences and skills with colleagues from other countries, we would have a great team of young and future European farmers, able to travel free and confident through the whole Europe and ready to be engaged in productive, commercial and research activities. These new young farmers may revive European agriculture and would not look any more like rural habitants, but international business-farmers, professionally speaking. In a brief survey among the assistants to the Fifth International Academic Conference titled "Alternative Income Sources in Small Agricultural Holdings of the European Union" held in Krakow (PL) in June 2015, participants from universities and countries like Poland, Hungary, Rep. Czech, Portugal, Romania, etc., expressed the necessity of addressing this problem in a new and bold way.

Removal of endocrine disrupting compounds from wastewater: a comparison between a conventional activated sludge with tertiary treatment and membrane bioreactors

Póster presentado en 19th International Congress of Chemical and Process Engineering, Prague, Czech Republic August 28th-September 1st, 2010.

Reduction of haloacetonitriles and haloacetones in natural waters using ceramic nanofiltration membranes

Póster presentado en 19th International Congress of Chemical and Process Engineering, Prague, Czech Republic August 28th-September 1st, 2010.