In situ study of Ge(100) surfaces with tertiarybutylphosphine supply in vapor phase epitaxy ambient

GaInP nucleation on Ge(100) often starts by annealing of the Ge(100) substrates under supply of phosphorus precursors. However, the influence on the Ge surface is not well understood. Here, we studied vicinal Ge(100) surfaces annealed under tertiarybutylphosphine (TBP) supply in MOVPE by in situ reflection anisotropy spectroscopy (RAS), X-ray photoelectron spectroscopy (XPS), and low energy electron diffraction (LEED). While XPS reveals a P termination and the presence of carbon on the Ge surface, LEED patterns indicate a disordered surface probably due to by-products of the TBP pyrolysis. However, the TBP annealed Ge(100) surface exhibits a characteristic RA spectrum, which is related to the P termination. RAS allows us to in situ control phosphorus desorption dependent on temperature.

Simulación del proceso de rotura por tracción de alambres de acero perlítico con un modelo de fisura cohesiva

La fractura de metales dúctiles como el acero suele explicarse a partir de la hipótesis de nucleación, crecimiento y coalescencia de microhuecos. A partir de esta teoría, se han desarrollado diversos modelos numéricos, entre los que el modelo de Gurson y sus variantes son los más extendidos. Dichos modelos reproducen matemáticamente el fenómeno físico de crecimiento de huecos resultando en un desarrollo progresivo del daño en el interior del material durante un ensayo de tracción. En estos modelos, el daño comienza a desarrollarse en fases muy tempranas del ensayo, incluso anteriores a la carga máxima. Ensayos realizados por los autores parecen indicar, sin embargo, que en el caso de barras de acero eutéctico empleado en la fabricación de alambres de pretensado, el daño originado en el interior del material como consecuencia del crecimiento de microhuecos sólo es apreciable en un estado muy avanzado del ensayo, momentos antes de producirse la rotura. Además, desde hace décadas se conoce que la triaxialidad de tensiones tiene una fuerte influencia sobre la rotura de los materiales. En este trabajo se presenta un modelo de rotura para elementos de acero sometidos a tracción, basado en un comportamiento cohesivo del material y que contempla el valor de la triaxialidad de tensiones, diferente en cada punto de la sección crítica de rotura. The fracture of ductile materials, such as steel, is usually explained with the theory of nucleation, growth and coalescence of microvoids. Based on this theory, many numerical models have been developed, with a special mention to Gurson-type models. These models simulate mathematically the physical growth of microvoids, leading to a progressive development of the internal damage that takes place during a tensile test. In these models, the damage starts to develop in very early stages of the test. Tests carried out by the authors seem to point out that, in the case of eutectoid steel bars used for manufacturing prestressing steel wires, the internal damage that takes place as a result of the growth of microvoids is only noticeable in a very advanced state of the test. In addition to this, it is known that the stress triaxiality has a strong influence over the fracture of ductile materials. This work presents a fracture model for steel specimens in a tensile test, based on a cohesive behaviour and taking into account the effect of stress triaxiality, which is different in every point of the fracture plane.

Optimization of the silicon subcell for III-V on silicon multijunction solar cells: key differences with conventional silicon technology

Dual-junction solar cells formed by a GaAsP or GaInP top cell and a silicon (Si) bottom cell seem to be attractive candidates to materialize the long sought-for integration of III-V materials on Si for photovoltaic (PV) applications. Such integration would offer a cost breakthrough for PV technology, unifying the low cost of Si and the efficiency potential of III-V multijunction solar cells. The optimization of the Si solar cells properties in flat-plate PV technology is well-known; nevertheless, it has been proven that the behavior of Si substrates is different when processed in an MOVPE reactor In this study, we analyze several factors influencing the bottom subcell performance, namely, 1) the emitter formation as a result of phosphorus diffusion; 2) the passivation quality provided by the GaP nucleation layer; and 3) the process impact on the bottom subcell PV properties.

A fracture model for pearlitic steel bars using a cohesive model

The fracture of ductile materials, such as metals, is usually explained with the theory of nucleation, growth and coalescence of microvoids. Based on this theory, many numerical models have been developed, with a special mention to Gurson-type models. These models simulate mathematically the physical growth of microvoids, leading to a progressive development of the internal damage that takes place during a tensile test. In these models, the damage starts to develop in very early stages of the test. Tests carried out by the authors suggest that, in the case of some eutectoid steels such as those used for manufacturing prestressing steel wires, the internal damage that takes place as a result of the growth of microvoids is only noticeable in very late stages of the tensile test. In the authors’ opinion, using a cohesive model as a failure criterion may be interesting in this case; a cohesive model only requires two parameters to be defined, with the fracture energy being one of them, which can be obtained experimentally. In addition to this, given that it is known that the stress triaxiality has a strong influence on the fracture of ductile materials, a cohesive model whose parameters are affected by the value of the stress triaxiality can be considered. This work presents a fracture model for steel specimens in a tensile test, based on a cohesive behaviour and taking into account the effect of stress triaxiality, which is different at each point of the fracture plane.

Simulación del proceso de rotura por tracción de alambres de acero perlítico con un modelo de fisura cohesiva

La fractura de metales dúctiles como el acero suele explicarse a partir de la hipótesis de nucleación, crecimiento y coalescencia de microhuecos. A partir de esta teoría, se han desarrollado diversos modelos numéricos, entre los que el modelo de Gurson y sus variantes son los más extendidos. Dichos modelos reproducen matemáticamente el fenómeno físico de crecimiento de huecos resultando en un desarrollo progresivo del daño en el interior del material durante un ensayo de tracción. En estos modelos, el daño comienza a desarrollarse en fases muy tempranas del ensayo, incluso anteriores a la carga máxima. Ensayos realizados por los autores parecen indicar, sin embargo, que en el caso de barras de acero eutéctico empleado en la fabricación de alambres de pretensado, el daño originado en el interior del material como consecuencia del crecimiento de microhuecos sólo es apreciable en un estado muy avanzado del ensayo, momentos antes de producirse la rotura. Además, desde hace décadas se conoce que la triaxialidad de tensiones tiene una fuerte influencia sobre la rotura de los materiales. En este trabajo se presenta un modelo de rotura para elementos de acero sometidos a tracción, basado en un comportamiento cohesivo del material y que contempla el valor de la triaxialidad de tensiones, diferente en cada punto de la sección crítica de rotura. The fracture of ductile materials, such as steel, is usually explained with the theory of nucleation, growth and coalescence of microvoids. Based on this theory, many numerical models have been developed, with a special mention to Gurson-type models. These models simulate mathematically the physical growth of microvoids, leading to a progressive development of the internal damage that takes place during a tensile test. In these models, the damage starts to develop in very early stages of the test. Tests carried out by the authors seem to point out that, in the case of eutectoid steel bars used for manufacturing prestressing steel wires, the internal damage that takes place as a result of the growth of microvoids is only noticeable in a very advanced state of the test. In addition to this, it is known that the stress triaxiality has a strong influence over the fracture of ductile materials. This work presents a fracture model for steel specimens in a tensile test, based on a cohesive behaviour and taking into account the effect of stress triaxiality, which is different in every point of the fracture plane.

A theoretical study on the formation of iodine oxide aggregates and monohydrates

Biotic and abiotic emissions of molecular iodine and iodocarbons from the sea or the ice surface and the intertidal zone to the coastal/polar marine boundary layer lead to the formation of iodine oxides, which subsequently nucleate forming iodine oxide particles (IOPs). Although the link between coastal iodine emissions and ultrafine aerosol bursts is well established, the details of the nucleation mechanism have not yet been elucidated. In this paper, results of a theoretical study of a range of potentially relevant aggregation reactions of different iodine oxides, as well as complexation with water molecules, are reported. Thermochemical properties of these reactions are obtained from high level ab initio correlated calculations including spin–orbit corrections. The results show that the nucleation path most likely proceeds through dimerisation of I2O4. It is also shown that water can hinder gas-to-particle conversion to some extent, although complexation with key iodine oxides does not remove enough of these to stop IOP formation. A consistent picture of this process emerges from the theoretical study presented here and the findings of a new laboratory study reported in the accompanying paper (Gomez Martin et al., 2013).

Preliminary mineralogy and ore petrology of the intermediate-sulfidation pallancata deposit, Ayacucho, Peru

Se investiga la compleja mineralogía del Yacimiento de Pallancata (6º productor de plata del mundo) y se establecen las condiciones de formación (P.T) basadas en la petrología de las menas comparada con los datos de mineralogía experimental y en la petrografía y microtermometría de inclusiones fluídas en la ganga silicatada, resultando un depósito típicamente caracterizado como epitermal de sulfuración intermedia.ABSTRACT:Pallancata is a world-class intermediate-sulfidation epithermal deposit, hosted by upper Miocene volcanics of the south-central Peruvian Andes in a sinuous N70ºW, ∼75º SW strike-slip structure, with wide (up to 35 m) pull-apart dilation zones related to bends of the vein strike. The structural evolution of the vein from earlier brecciation to later open space infill resembles the Shila Paula district (Chauvet et al. 2006). Fluid inclusion petrography and microthermometry show that ore deposition is related to protracted boiling of very diluted, mainly meteoric fluids, starting at 250–260 ºC, under ∼300 m hydrostatic head. The mineralogical-petrological study reveals a complex sequence of mineralization (eight stages) and mineral reactions consistent with Ag2S enrichment or Sb2S3 depletion, or both, during cooling over the temperature range 250–200 ºC: pyrite, sphalerite, galena, miargyrite, pyrargyrite-proustite, chalcopyrite, polybasite-pearceite, argentite (now acanthite), and Au–Ag alloy (“electrum”). This Ag2S enrichment and Sb2S3depletion during cooling may be explained by decay of a Ag-rich galena precursor at deeper levels (Pb2S2–AgSbS2 solid solution), which rapidly becomes unstable with decreasing temperature, producing residual (stoichiometric) PbS and more mobile Ag and Sb sulfide phases, which migrated upward and laterally away from the thermal core of the system. The core is still undisclosed by mining works, but the available geochemical evidence (logAg/log Pb ratios decreasing at depth) is consistent with this interpretation, implying a deeper potential resource. Data from sulfide geothermometry, based on mineral equilibria, document the thermal evolution of the system below 200 ºC (stephanite, uytenbogaardtite, jalpaite, stromeyerite, mckinstryite, among others). The end of the most productive stages (3, 4, and 5) is marked by the precipitation of stephanite at temperatures below 197 ± 5 ºC, but precipitation of residual silver continues through the waning stages of the hydrothermal system down to <93.3 ºC (stromeyerite) or in a supergene redistribution (stage 8, acanthite II).

In situ control of the GE(100)surface domain structure for III-V multijunction solar cells

Vicinal Ge(100) is the common substrate for state of the art multi-junction solar cells grown by metal-organic vapor phase epitaxy (MOVPE). While triple junction solar cells based on Ge(100) present efficiencies mayor que 40%, little is known about the microscopic III-V/Ge(100) nucleation and its interface formation. A suitable Ge(100) surface preparation prior to heteroepitaxy is crucial to achieve low defect densities in the III-V epilayers. Formation of single domain surfaces with double layer steps is required to avoid anti-phase domains in the III-V films. The step formation processes in MOVPE environment strongly depends on the major process parameters such as substrate temperature, H2 partial pressure, group V precursors [1], and reactor conditions. Detailed investigation of these processes on the Ge(100) surface by ultrahigh vacuum (UHV) based standard surface science tools are complicated due to the presence of H2 process gas. However, in situ surface characterization by reflection anisotropy spectroscopy (RAS) allowed us to study the MOVPE preparation of Ge(100) surfaces directly in dependence on the relevant process parameters [2, 3, 4]. A contamination free MOVPE to UHV transfer system [5] enabled correlation of the RA spectra to results from UHV-based surface science tools. In this paper, we established the characteristic RA spectra of vicinal Ge(100) surfaces terminated with monohydrides, arsenic and phosphorous. RAS enabled in situ control of oxide removal, H2 interaction and domain formation during MOVPE preparation.

Effect of Stress Level on the High Temperature Deformation and Fracture Mechanisms of Ti-45Al-2Nb-2Mn-0.8 vol. pct TiB2: An In Situ Experimental Study

The effect of the applied stress on the deformation and crack nucleation and propagation mechanisms of a c-TiAl intermetallic alloy (Ti-45Al-2Nb-2Mn (at. pct)-0.8 vol. pct TiB2) was examined by means of in situ tensile (constant strain rate) and tensile-creep (constant load) experiments performed at 973 K (700 �C) using a scanning electron microscope. Colony boundary cracking developed during the secondary stage in creep tests at 300 and 400 MPa and during the tertiary stage of the creep tests performed at higher stresses. Colony boundary cracking was also observed in the constant strain rate tensile test. Interlamellar ledges were only found during the tensile-creep tests at high stresses (r>400 MPa) and during the constant strain rate tensile test. Quantitative measurements of the nature of the crack propagation path along secondary cracks and along the primary crack indicated that colony boundaries were preferential sites for crack propagation under all the conditions investigated. The frequency of interlamellar cracking increased with stress, but this fracture mechanism was always of secondary importance. Translamellar cracking was only observed along the primary crack.

Determination of the hoop fracture properties of unirradiated hydrogen-charged nuclear fuel cladding from ring compression tests

In this work, a new methodology is devised to obtain the fracture properties of nuclear fuel cladding in the hoop direction. The proposed method combines ring compression tests and a finite element method that includes a damage model based on cohesive crack theory, applied to unirradiated hydrogen-charged ZIRLOTM nuclear fuel cladding. Samples with hydrogen concentrations from 0 to 2000 ppm were tested at 20 �C. Agreement between the finite element simulations and the experimental results is excellent in all cases. The parameters of the cohesive crack model are obtained from the simulations, with the fracture energy and fracture toughness being calculated in turn. The evolution of fracture toughness in the hoop direction with the hydrogen concentration (up to 2000 ppm) is reported for the first time for ZIRLOTM cladding. Additionally, the fracture micromechanisms are examined as a function of the hydrogen concentration. In the as-received samples, the micromechanism is the nucleation, growth and coalescence of voids, whereas in the samples with 2000 ppm, a combination of cuasicleavage and plastic deformation, along with secondary microcracking is observed.

Molecular dynamics modeling and simulation of void growth in two dimensions

The mechanisms of growth of a circular void by plastic deformation were studied by means of molecular dynamics in two dimensions (2D). While previous molecular dynamics (MD) simulations in three dimensions (3D) have been limited to small voids (up to ≈10 nm in radius), this strategy allows us to study the behavior of voids of up to 100 nm in radius. MD simulations showed that plastic deformation was triggered by the nucleation of dislocations at the atomic steps of the void surface in the whole range of void sizes studied. The yield stress, defined as stress necessary to nucleate stable dislocations, decreased with temperature, but the void growth rate was not very sensitive to this parameter. Simulations under uniaxial tension, uniaxial deformation and biaxial deformation showed that the void growth rate increased very rapidly with multiaxiality but it did not depend on the initial void radius. These results were compared with previous 3D MD and 2D dislocation dynamics simulations to establish a map of mechanisms and size effects for plastic void growth in crystalline solids.

Simulación de la rotura de barras de acero perlítico sometidas a tracción mediante un modelo de fisura cohesiva. Validación experimental

Las probetas cilíndricas fabricadas con materiales metálicos de elevada ductilidad, como el aluminio o el cobre, sometidas a tracción suelen presentar una rotura comúnmente denominada rotura en copa y cono, debido a su geometría. Este tipo de rotura se reproduce numéricamente con éxito mediante el modelo de Gurson-Tvergaard- Needleman, cuya formulación matemática se basa en el fenómeno físico de nucleación, crecimiento y coalescencia de microhuecos. A diferencia de dichos materiales, las barras de acero perlítico, material con una ductilidad apreciable, presentan un frente de rotura plano que no puede simularse correctamente con los modelos antes mencionados, apareciendo una región interior de daño que, en principio, también puede atribuirse a un fenómeno de nucleación y crecimiento de microhuecos, mientras que en el exterior aparece una zona cuya micrografía permite asociar su rotura a un mecanismo de clivaje. En trabajos anteriores los autores han presentado un elemento de intercara cohesivo dependiente de la triaxialidad de tensiones que, incorporado a un código de elementos finitos, permite reproducir de forma razonable el daño que se desarrolla en la región interior mencionada. En este trabajo se presentan los resultados de una campaña experimental que permite validar el modelo desarrollado. Para ello, se ensayan probetas de diferentes diámetros y se comparan los resultados con los obtenidos numéricamente, empleando tres bases extensométricas diferentes en cada uno de los diámetros. Los resultados numéricos se ajustan razonablemente bien a los obtenidos experimentalmente.The cylindrical specimens made of high-ductility metallic materials, such as aluminium and copper, usually fail showing a fracture surface commonly known as cup-cone fracture because of its shape. This type of fracture is successfully reproduced using the Gurson-Tvergaard-Needleman model, which is based on the physical process of nucleation, growth and coalescence of microvoids. Unlike these materials, pearlitic steel bars, which are considerably ductile, show a flat fracture surface that cannot be correctly reproduced with the aforementioned models. In this flat fracture surface, a dark region can be observed in the centre of the specimen, which is the result of a process of nucleation and growth of microvoids, while in the rest of the fracture surface a different region can be identified, which a micrographic study reveals to be the result of a process of cleavage. In previous works, the authors presented a triaxiality-dependent cohesive interface element that, implemented in a finite element code, can reproduce in a reasonably accurate manner the damage that takes place in the dark region mentioned before. The results of an experimental campaign designed to validate the model are presented in this paper. For it, different diameter specimens are tested and these results are compared to those obtained with the numerical models, using three different initial lengths for the strain. Numerical results agree reasonably well with those obtained experimentally.

Simulación de la rotura de barras de acero perlítico sometidas a tracción mediante un modelo de fisura cohesiva. Validación experimental

Las probetas cilíndricas fabricadas con materiales metálicos de elevada ductilidad, como el aluminio o el cobre, sometidas a tracción suelen presentar una rotura comúnmente denominada rotura en copa y cono, debido a su geometría. Este tipo de rotura se reproduce numéricamente con éxito mediante el modelo de Gurson-Tvergaard- Needleman, cuya formulación matemática se basa en el fenómeno físico de nucleación, crecimiento y coalescencia de microhuecos. A diferencia de dichos materiales, las barras de acero perlítico, material con una ductilidad apreciable, presentan un frente de rotura plano que no puede simularse correctamente con los modelos antes mencionados, apareciendo una región interior de daño que, en principio, también puede atribuirse a un fenómeno de nucleación y crecimiento de microhuecos, mientras que en el exterior aparece una zona cuya micrografía permite asociar su rotura a un mecanismo de clivaje. En trabajos anteriores los autores han presentado un elemento de intercara cohesivo dependiente de la triaxialidad de tensiones que, incorporado a un código de elementos finitos, permite reproducir de forma razonable el daño que se desarrolla en la región interior mencionada. En este trabajo se presentan los resultados de una campaña experimental que permite validar el modelo desarrollado. Para ello, se ensayan probetas de diferentes diámetros y se comparan los resultados con los obtenidos numéricamente, empleando tres bases extensométricas diferentes en cada uno de los diámetros. Los resultados numéricos se ajustan razonablemente bien a los obtenidos experimentalmente.The cylindrical specimens made of high-ductility metallic materials, such as aluminium and copper, usually fail showing a fracture surface commonly known as cup-cone fracture because of its shape. This type of fracture is successfully reproduced using the Gurson-Tvergaard-Needleman model, which is based on the physical process of nucleation, growth and coalescence of microvoids. Unlike these materials, pearlitic steel bars, which are considerably ductile, show a flat fracture surface that cannot be correctly reproduced with the aforementioned models. In this flat fracture surface, a dark region can be observed in the centre of the specimen, which is the result of a process of nucleation and growth of microvoids, while in the rest of the fracture surface a different region can be identified, which a micrographic study reveals to be the result of a process of cleavage. In previous works, the authors presented a triaxiality-dependent cohesive interface element that, implemented in a finite element code, can reproduce in a reasonably accurate manner the damage that takes place in the dark region mentioned before. The results of an experimental campaign designed to validate the model are presented in this paper. For it, different diameter specimens are tested and these results are compared to those obtained with the numerical models, using three different initial lengths for the strain. Numerical results agree reasonably well with those obtained experimentally.

Blends of babassu, palm kernal and coconut mame with fossil kerosene: low carbon number methyl esters as a possible source for renewable jet fuel

Three different oils: babassu, coconut and palm kernel have been transesterified with methanol. The fatty acid methyl esters (FAME) have been subjected to vacuum fractional distillation, and the low boiling point fractions have been blended with fossil kerosene at three different proportions: 5, 10 and 20% vol.

Movimiento de paredes de dominio magnético en nanohilos con defectos controlados

La investigación realizada en este trabajo de tesis se ha centrado en el estudio de la generación, anclaje y desenganche de paredes de dominio magnético en nanohilos de permalloy con defectos controlados. Las últimas tecnologías de nanofabricación han abierto importantes líneas de investigación centradas en el estudio del movimiento de paredes de dominio magnético, gracias a su potencial aplicación en memorias magnéticas del futuro. En el 2004, Stuart Parkin de IBM introdujo un concepto innovador, el dispositivo “Racetrack”, basado en un nanohilo ferromagnético donde los dominios de imanación representan los "bits" de información. La frontera entre dominios, ie pared magnética, se moverían en una situación ideal por medio de transferencia de espín de una corriente polarizada. Se anclan en determinadas posiciones gracias a pequeños defectos o constricciones de tamaño nanométrico fabricados por litografía electrónica. El éxito de esta idea se basa en la generación, anclaje y desenganche de las paredes de dominio de forma controlada y repetitiva, tanto para la lectura como para la escritura de los bits de información. Slonczewski en 1994 muestra que la corriente polarizada de espín puede transferir momento magnético a la imanación local y así mover paredes por transferencia de espín y no por el campo creado por la corriente. Desde entonces muchos grupos de investigación de todo el mundo trabajan en optimizar las condiciones de transferencia de espín para mover paredes de dominio. La fracción de electrones polarizados que viaja en un hilo ferromagnético es considerablemente pequeña, así hoy por hoy la corriente necesaria para mover una pared magnética por transferencia de espín es superior a 1 107 A/cm2. Una densidad de corriente tan elevada no sólo tiene como consecuencia una importante degradación del dispositivo sino también se observan importantes efectos relacionados con el calentamiento por efecto Joule inducido por la corriente. Otro de los problemas científico - tecnológicos a resolver es la diversidad de paredes de dominio magnético ancladas en el defecto. Los diferentes tipos de pared anclados en el defecto, su quiralidad o el campo o corriente necesarios para desenganchar la pared pueden variar dependiendo si el defecto posee dimensiones ligeramente diferentes o si la pared se ancla con un método distinto. Además, existe una componente estocástica presente tanto en la nucleación como en el proceso de anclaje y desenganche que por un lado puede ser debido a la naturaleza de la pared que viaja por el hilo a una determinada temperatura distinta de cero, así como a defectos inevitables en el proceso de fabricación. Esto constituye un gran inconveniente dado que según el tipo de pared es necesario aplicar distintos valores de corriente y/o campo para desenganchar la pared del defecto. Como se menciona anteriormente, para realizar de forma eficaz la lectura y escritura de los bits de información, es necesaria la inyección, anclaje y desenganche forma controlada y repetitiva. Esto implica generar, anclar y desenganchar las paredes de dominio siempre en las mismas condiciones, ie siempre a la misma corriente o campo aplicado. Por ello, en el primer capítulo de resultados de esta tesis estudiamos el anclaje y desenganche de paredes de dominio en defectos de seis formas distintas, cada uno, de dos profundidades diferentes. Hemos realizado un análisis estadístico en diferentes hilos, donde hemos estudiado la probabilidad de anclaje cada tipo de defecto y la dispersión en el valor de campo magnético aplicado necesario para desenganchar la pared. Luego, continuamos con el estudio de la nucleación de las paredes de dominio magnético con pulsos de corriente a través una linea adyacente al nanohilo. Estudiamos defectos de tres formas distintas e identificamos, en función del valor de campo magnético aplicado, los distintos tipos de paredes de dominio anclados en cada uno de ellos. Además, con la ayuda de este método de inyección que es rápido y eficaz, hemos sido capaces de generar y anclar un único tipo de pared minimizando el comportamiento estocástico de la pared mencionado anteriormente. En estas condiciones óptimas, hemos estudiado el desenganche de las paredes de dominio por medio de corriente polarizada en espín, donde hemos conseguido desenganchar la pared de forma controlada y repetitiva siempre para los mismos valores de corriente y campo magnético aplicados. Además, aplicando pulsos de corriente en distintas direcciones, estudiamos en base a su diferencia, la contribución térmica debido al efecto Joule. Los resultados obtenidos representan un importante avance hacia la explotación práctica de este tipo de dispositivos. ABSTRACT The research activity of this thesis was focused on the nucleation, pinning and depinning of magnetic domain walls (DWs) in notched permalloy nanowires. The access to nanofabrication techniques has boosted the number of applications based on magnetic domain walls (DWs) like memory devices. In 2004, Stuart Parkin at IBM, conceived an innovative concept, the “racetrack memory” based on a ferromagnetic nanowire were the magnetic domains constitute the “bits” of information. The frontier between those magnetic domains, ie magnetic domain wall, will move ideally assisted by a spin polarized current. DWs will pin at certain positions due to artificially created pinning sites or “notches” fabricated with ebeam lithography. The success of this idea relies on the careful and predictable control on DW nucleation and a defined pinning-depinning process in order to read and write the bits of information. Sloncsewski in 1994 shows that a spin polarized current can transfer magnetic moment to the local magnetization to move the DWs instead of the magnetic field created by the current. Since then many research groups worldwide have been working on optimizing the conditions for the current induced DW motion due to the spin transfer effect. The fraction of spin polarized electrons traveling through a ferromagnetic nanowire is considerably small, so nowadays the current density required to move a DW by STT exceeds 1 107 A/cm2. A high current density not only can produce a significant degradation of the device but also important effects related to Joule heating were also observed . There are other scientific and technological issues to solve regarding the diversity of DWs states pinned at the notch. The types of DWs pinned, their chirality or their characteristic depinning current or field, may change if the notch has slightly different dimensions, the stripe has different thickness or even if the DW is pinned by a different procedure. Additionally, there is a stochastic component in both the injection of the DW and in its pinning-depinning process, which may be partly intrinsic to the nature of the travelling DW at a non-zero temperature and partly due to the unavoidable defects introduced during the nano-fabrication process. This constitutes an important inconvenient because depending on the DW type different values of current of magnetic field need to be applied in order to depin a DW from the notch. As mentioned earlier, in order to write and read the bits of information accurately, a controlled reproducible and predictable pinning- depinning process is required. This implies to nucleate, pin and depin always at the same applied magnetic field or current. Therefore, in the first chapter of this thesis we studied the pinning and depinning of DW in six different notch shapes and two depths. An statistical analysis was conducted in order to determine which notch type performed best in terms of pinning probability and the dispersion measured in the magnetic field necessary to depin the magnetic DWs. Then, we continued studying the nucleation of DWs with nanosecond current pulses by an adjacent conductive stripe. We studied the conditions for DW injection that allow a selective pinning of the different types of DWs in Permalloy nanostripes with 3 different notch shapes. Furthermore, with this injection method, which has proven to be fast and reliable, we manage to nucleate only one type of DW avoiding its stochastic behavior mentioned earlier. Having achieved this optimized conditions we studied current induced depinning where we also achieved a controlled and reproducible depinning process at always the same applied current and magnetic field. Additionally, changing the pulse polarity we studied the joule heating contribution in a current induced depinning process. The results obtained represent an important step towards the practical exploitation of these devices.