Preparation and characterization of rubidium-beta-alumina by the gel-to-crystallite conversion method

Preparation of Rb-beta -alumina was realized by the gel-to-crystallite conversion method. Reaction of hydrated aluminum hydroxide gel with RbOH in ethanol medium gave rise to the Rb+-inserted pseudoboehmite precursor under wet chemical conditions. The thermal decomposition of the precursor yielded Rb-beta -alumina. The Rb2O:Al2O3 ratio of monophasic Rb-beta -alumina ranged from 1:10 to 1:22. The extended stability in the compositional range is due to the fact that the conduction planes containing Rb+ and O2- ions can have lower occupancy of Rb+ ions for larger sized alkali ions, permitting the steric separation of the adjoining spinel blocks. High-resolution electron microscopy revealed that the decreasing occupancy of alkali ions in the conduction plane is balanced by changing widths of spinel blocks arising from the shift of tetrahedral Al3+ ions to octahedral sites and an accompanying increase in stacking defects. (C) 2000 Elsevier Science Ltd. All rights reserved.

Theoretical and Experimental Studies on an Ammonia-Based Loop Heat Pipe With a Flat Evaporator

An ammonia loop heat pipe (LHP) with a flat plate evaporator is developed and tested. The device uses a nickel wick encased in an aluminum-stainless steel casing. The loop is tested for various heat loads and different sink temperatures, and it demonstrated reliable startup characteristics. Results with the analysis of the experimental observation indicate that the conductance between the compensation chamber and the heater plate can significantly influence the operating temperatures of the LHP. A mathematical model is also presented which is validated against the experimental observations.

Experimental studies and phase field modeling of microstructure evolution during solidification with electromagnetic stirring

Thixocasting requires manufacturing of billets with non-dendritic microstructure. Aluminum alloy A356 billets were produced by rheocasting in a mould placed inside a linear electromagnetic stirrer. Subsequent heat treatment was used to produce a transition from rosette to globular microstructure. The current and the duration of stirring were explored as control parameters. Simultaneous induction heating of the billet during stirring was quantified using experimentally determined thermal profiles. The effect of processing parameters on the dendrite fragmentation was discussed. Corresponding computational modeling of the process was performed using phase-field modeling of alloy solidification in order to gain insight into the process of morphological changes of a solid during this process. A non-isothermal alloy solidification model was used for simulations. The morphological evolution under such imposed thermal cycles was simulated and compared with experimentally determined one. Suitable scaling using the thermosolutal diffusion distances was used to overcome computational difficulties in quantitative comparison at system scale. The results were interpreted in the light of existing theories of microstructure refinement and globularisation.

Quasicrystalline and related crystalline phases in a rapidly solidified 2024-2Li aluminium alloy

The formation and decomposition of quasicrystalline and crystalline phases in as-rapidly solidified and annealed commercial AISI 2024 aluminum alloy containing 2 wt% Li have been investigated by detailed transmission electron microscopy, including a combination of bright field and dark field imaging, selected area diffraction pattern analysis and energy dispersive X-ray microanalysis. The microstructure of as-melt spun 2024-2Li consists of alpha-Al cells, containing small coherent delta' precipitates, and particles or a continuous network of the icosahedral phase at the cell boundaries. After annealing at 300-degrees-C, the intercellular particles of the icosahedral phase coarsen progressively and assume a more faceted shape; after annealing at 400-degrees-C, particles of the decagonal and crystalline O phases precipitate heterogeneously on preexisting particles of the icosahedral phase; and after annealling at 500-degrees-C, the icosahedral and decagonal phases dissolve completely, and small particles of the crystalline O phase remain together with newly precipitated plates of the T1 phase. The icosahedral phase in melt spun and melt spun/annealed 2024-2Li belongs to the Al6CuLi3 class of icosahedral phases, with a quasilattice constant of 0.51 nm, a stoichiometry of (Al, Si)6(Cu, Mn, Fe) (Li, Mg)3 and an average composition of Al-24.1 at.% Cu-6.4 at.% Mg-1.7 at.% Si-0.3 at.% Mn-0.5 at.% Fe as-melt spun and Al-21.9 at.% Cu-6.3 at.% Mg-1.0 at.% Si-0.5 at.% Fe as-heat-treated. The decagonal phase in melt spun/annealed 2024-2Li belongs to the Al4Mn class of decagonal phases, with a periodicity of 1.23 nm along the 10-fold symmetry axis, a stoichiometry of Al3(Cu, Mn, Fe) and an average composition of Al-10.3 at.% Cu-13.8 at.% Mn-2.3 at.% Fe. The crystalline O phase in melt spun/annealed 2024-2Li has an orthorhombic structure with lattice parameters of a = 2.24 nm, b = 2.35 nm and c = 1.23 nm, a stoichiometry of Al3(Cu, Mn, Fe) and an average composition of Al-11.0 at.% Cu-14.8 at.% Mn-3.9 at.% Fe. Detailed analysis of selected area diffraction patterns shows a close similarity between the icosahedral, decagonal and crystalline O phases in melt spun and melt spun/annealed 2024-2Li. In particular, the decagonal phase and crystalline O phases have a similar composition, and exhibit an orientation relationship which can be expressed as: [GRAPHICS] suggesting that the orthorhombic O phase is an approximant structure for the decagonal phase.

Silicon tetrafluoride : Preparation and reduction with lithium aluminium hydride

Pure silicon tetrafluoride can be prepared in 66% yield from silicon tetrachloride by refluxing with lead fluoride in acetonitrile. The gas can be reduced to pure silane by lithium aluminum hydride in diethyl ether.

On determining the elastic modulus of a cylindrical sample subjected to flexural excitation in a resonant column apparatus

For resonant column tests conducted in the flexure mode of excitation, a new methodology has been proposed to find the elastic modulus and associated axial strain of a cylindrical sample. The proposed method is an improvement over the existing one, and it does not require the assumption of either the mode shape or zero bending moment condition at the top of the sample. A stepwise procedure is given to perform the necessary calculations. From a number of resonant column experiments on aluminum bars and dry sand samples, it has been observed that the present method as compared with the one available in literature provides approximately (i) 5.9%-7.3% higher values of the elastic modulus and (ii) 6.5%-7.3% higher values of the associated axial strains.

A geodesic-based triangulation technique for damage location in metallic and composite plates

Lamb-wave-based damage detection methods using the triangulation technique are not suitable for handling structures with complex shapes and discontinuities as the parametric/analytical representation of these structures is very difficult. The geodesic concept is used along with the triangulation technique to overcome the above problem. The present work is based on the fundamental fact that a wave takes the minimum energy path to travel between two points on any multiply connected surface and this reduces to the shortest distance path or geodesic. The geodesics are computed on the meshed surface of the structure using the fast marching method. The wave response matrix of the given sensor configuration for the healthy and the damaged structure is obtained experimentally. The healthy and damage response matrices are compared and their difference gives the time information about the reflection of waves from the damage. A wavelet transform is used to extract the arrival time information of the wave scattered by the damage from the acquired Lamb wave signals. The computed geodesics and time information are used in the ellipse algorithm of triangulation formulation to locate the loci of possible damage location points for each actuator-sensor pair. The results obtained for all actuator-sensor pairs are combined and the intersection of multiple loci gives the damage location result. Experiments were conducted in aluminum and composite plate specimens to validate this method.

Debenzylation by Ni-A1 alloy

Nickel-aluminum alloy in aqueous sodium hydroxide-ethanol medium brings about facile hydro-enolrsis of benzyl ether function in substrates carrying a vicinal methoxy group. Simplicity of the reaction conditions and cheapness of the reagent are some of the advanrages of the procedure. Additionally, carbonyl functions when present are untouched and alkaline medium of the reaction makes it compatible with the presence of acid-sensitite groups.

A method for estimation of the radius of elastic-plastic boundary around cold-worked holes

The radius of an elastic-plastic boundary was measured by the strain gage method around the cold-worked region in L72-aluminum alloy. The relative radial expansion was varied from 2.5 to 6.5 percent during the cold-working process using mandrel and split sleeve. The existing theoretical studies in this area are reviewed. The experimental results are compared with existing experimental data of various investigators and with various theoretical formulations. A model is developed to predict the radius of elastic-plastic boundary, and the model is assessed by comparing with the present experiments.

Numerical and experimental study of the thermal behaviour of coining and upsetting processes

A numerical simulation technique has been employed to study the thermal behavior of hot-forging type forming processes. Experiments on the coining and upsetting of an aluminum billet were conducted to validate the numerical predictions. Typical forming conditions for both the coining and upsetting processes were then studied in detail. an electrical analogy scheme was used to determine the thermal contact resistance. This scheme can conviniently provide the interface characteristics for typical processing conditions, which normally involve high pressures and temperatures. A single forging cycle was first considered, and then a batch of twenty-five forgings was studied. Each forging cycle includes the billet mounting, ascent, loading, dwelling, unloading, descent, and billet removal stages. The temperature distribution in the first forging to be formed is found to be significantly different from that at the end of the batch. In industry, forging is essentially a batch operation. The influence of forming speed and reduction on thermal characteristics was investigated also. The variations that can occur in the process design by considering differences in temperature characteristics are discussed also.

Formation of a single, rotated-Brass (1 1 0)< 5 5 6 > texture by hot cross-rolling of an Al-Zn-Mg-Cu-Zr alloy

The present work describes the evolution of a strong, single-component rotated-Brass ((1 1 0) < 5 5 6 >) texture in an Al-Zn-Mg-Cu-Zr alloy by an uneven hot cross-rolling with frequent interpass annealing. This texture development is unique because hot rolling of aluminum alloys results in orientation distribution along the ``beta-fibre''. It has been demonstrated that the deformation by cross-rolling of a partially recrystallized grain structure having rotated-Cube and Goss orientations, and the recrystallization resistance of near-Brass-oriented elongated grains play a critical role in development of this texture. (C) 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Onttojen puiden lahopuukovakuoriaiset — kolmen pyydystyypin vertailu

Vanhat ja ontot puut ovat tärkeä elinympäristö monelle lahopuusta riippuvaiselle eliölajille. Onttoihin puihin on erikoistunut suuri määrä myös vaarantuneita ja harvinaisia hyönteislajeja, jotka elävät puun onkalon seinämillä tai onkalon pohjalle kerääntyvässä orgaanisessa aineksessa, ns. mulmissa. Tutkimuksen tavoitteena oli selvittää, mikä kolmesta pyydystyypistä (ikkuna-, vuoka- ja kuoppapyydys) soveltuu parhaiten onttojen puiden lahopuukovakuoriaisten pyyntiin. Lisäksi tavoitteena oli kartoittaa hyönteisnäytteiden ensimmäiseen laboratoriokäsittelyyn vaadittua aikaa. Tutkimuksessa oli mukana vanhoja rungostaan onttoutuneita lehmuksia, tammia ja vaahteroita pääkaupunkiseudun puisto- ja kartanoalueilta. Puiden onkaloiden sisään aseteltiin ikkuna-, vuoka- ja kuoppapyydyksiä, kaksi kutakin tyyppiä ja ne tyhjennettiin kolmen viikon välein touko-heinäkuussa 2006. Pyydyksiä oli siis yhteensä 90 per pyyntijakso. Kun näytteistä eroteltiin halutut hyönteislahkot (mukaanlukien kovakuoriaiset) niiden käsittelyyn käytetty aika kirjattiin ylös. Aineistosta tunnistettiin yhteensä 3825 kovakuoriaisyksilöä ja 212 lajia, joista lahopuusta riippuvaisia oli yhteensä 3398 yksilöä ja 121 lajia. Ikkunapyydyksissä esiintyi yhteensä 1639 yksilöä ja 140 lajia, vuokapyydyksissä 1506 yksilöä ja 134 lajia, kuoppapyydyksissä 680 yksilöä ja 111 lajia. Näytteiden käsittelyaikojen keskiarvot olivat 48,3 minuuttia ikkunapyydykselle, 65,5 minuuttia vuokapyydykselle ja 34,1 kuoppapyydykselle. Lajistokoostumuksen huomioiva ?-diversiteetti erosi huomattavasti pyydysten välillä, se oli 36,5 % ikkuna- ja vuokapyydysten välillä, 13,1 % ikkuna- ja kuoppapyydysten välillä ja 14,2 % vuoka- ja kuoppapyydysten välillä. Ikkuna- ja vuokapyydysten välillä ei havaittu tilastollisesti merkitsevää eroa saproksyylilajien (p<0,05), -yksilöiden (p<0,05) tai käsittelyaikojen (p<0,05) keskiarvoissa. Ikkuna- ja vuokapyydyksillä saatiin keskimäärin selvästi enemmän saproksyylilajeja ja –yksilöitä kuoppapyydykseen verrattuna. Kuoppapyydyksellä saatiin kokonaisyksilömäärään verrattuna suhteellisesti vähemmän saproksyylejä (59 %) kuin ikkuna- (69 %) ja vuokapyydyksillä (71 %). Ikkunapyydykset olivat tehokkain pyydystyyppi vertailtaessa pyydysten keräämää saproksyyliyksilömäärää suhteessa aineiston käsittelyn vaatimaan aikaan. Tehokkuus (yksilöä minuutissa) ikkunapyydykselle oli 0,74, vuokapyydykselle 0,43 ja kuoppapyydykselle 0,21. Ikkunapyydyksiä ei ole aikaisemmin käytetty puun onkalon sisällä hyönteisiä pyydettäessä vaan ne ovat aikaisemmissa tutkimuksissa roikkuneet onkalon ulkopuolella. Ikkunapyydykset kuitenkin toimivat erinomaisesti myös onkaloiden sisällä. Ikkuna- sekä vuokapyydys toimivatkin selkeästi paremmin lahopuukovakuoriaisten pyynnissä verrattuna kuoppapyydykseen, jonka poisjättäminen olisi kuitenkin tuottanut huomattavasti lajiköyhemmän aineiston. Mahdollisimman monimuotoisen onttojen puiden lahopuukovakuoriaislajiston keräämiseksi tulisi käyttää ikkuna- tai vuokapyydyksiä yhdessä kuoppapyydysten kanssa.

Coordination-Driven Self-Assembly of M3L2 Trigonal Cages from Preorganized Metalloligands Incorporating Octahedral Metal Centers and Fluorescent Detection of Nitroaromatics

The design and preparation of novel M3L2 trigonal cages via the coordination-driven self-assembly of preorganized metalloligands containing octahedral aluminum(III), gallium(III), or ruthenium(II) centers is described. When tritopic or dinuclear linear metalloligands and appropriate complementary subunits are employed, M3L2 trigonal-bipyramidal and trigonal-prismatic cages are self-assembled under mild conditions. These three-dimensional cages were characterized with multinuclear NMR spectroscopy (H-1 and P-31) and high-resolution electrospray ionization mass spectrometry. The structure of one such trigonal-prismatic cage, self-assembled from an arene ruthenium metalloligand, was confirmed via single-crystal X-ray crystallography. The fluorescent nature of these prisms, due to the presence of their electron-rich ethynyl functionalities, prompted photophysical studies, which revealed that electron-deficient nitroaromatics are effective quenchers of the cages' emission. Excited-state charge transfer from the prisms to the nitroaromatic substrates can be used as the basis for the development of selective and discriminatory turn-off fluorescent sensors for nitroaromatics.

Stabilized alpha-Ni(OH)2 as electrode material for for alkaline secondary cells

Hydrotalcite-like compounds of formula Ni1-xAl(x)(OH)2(CO3)x/2 . nH2O (x = 0.1 to 0.25), having the same structure as that of alpha-Ni(OH)2, have been synthesized by substituting nickel hydroxide with aluminum. Of these, the compounds of compositions x greater-than-or-equal-to 0.2 are found to have prolonged stability in strong alkaline medium. The electrodes comprising stabilized alpha-Ni(OH)2 of x = 0.2 composition are rechargeable with discharge-capacity values of 240 (+/- 15) mAh-g-1 and are attractive for applications in various alkaline secondary cells employing nickel-positive electrodes.

Microstructure control and wear of Al2O3-SiC-(Al,Si) composites made by melt oxidation

Ceramic matrix composites of Al2O3-SiC-(Al,Si) have been fabricated by directed melt oxidation of aluminum alloys into SiC particulate preforms. The proportions of Al2O3, alloy, and porosity in the composite can be controlled by proper selection of SLC particle size and the processing temperature. The wear resistance of composites was evaluated in pin-on-disk experiments against a hard steel substrate. Minimum wear rate comparable to conventional ceramics such as ZTA is recorded for the composition containing the highest fraction of alloy, owing to the development of a thin and adherent tribofilm with a low coefficient of friction.