Dry sliding wear of A356-Al-SiCp composites

Aluminium alloy (A356)-SiC composites containing 15 and 25 wt.% silicon carbide particles (average size 43 μm) were tested for sliding wear at different loads using a pin on disc machine. Composites exhibited better wear resistance compared with unreinforced alloy up to a pressure of 26 MPa. Scanning electron microscopy examination of worn surfaces and subsurfaces show that the presence of dispersed SiC particles help in reducing the propensity of material flow at the surface, at the same time leading to the formation of an iron-rich layer on the surface.

Effect Of Electroslag Refining On Microstructure And Mechanical-Properties Of Is-7670 Alloy

The electroslag refining technique is one of the modern tools which is capable of imparting superior mechanical and chemical properties to metals and alloys. Refining usually results in the elimination of a number of casting or solidification defects, such as shrinkage porosity, gas porosity, pipe, micro- and macro segregation. Remelting also imparts a directional grain structure apart from refining the size of the inclusions, grains and precipitates. This technique has over the years been used widely and successfully to improve the mechanical and chemical properties of steels and alloy steels which are used in the nuclear, missile, aerospace and marine industries for certain critical applications. But the application of ESR to aluminium and its alloys is only recent. This paper investigates the response of an aluminium alloy (corresponding to the Indian Specification IS: 7670) to ESR. Based on theoretical considerations and microstructural evidence it elucidates how ESR of aluminium alloys differs from that of ferrous alloys. The improvement achieved in mechanical properties of the alloy is correlated with the microstructure.

A Study of The Fatigue, Impact and fracture-Toughness Characteristics of Electroslag Refined IS-7670 Alloy

The nuclear, aerospace, naval and missile industries place emphasis on materials with high structural integrity and reliable performance so as to meet certain stringent requirements in service. Strength is not the only criterion for selection. Properties such as fatigue resistance. impact toughness and fracture toughness are equally important. Electroslag refining (ESR) has been used widely and successfully over the years for improving the fatigue resistance, creep resistance, impact strength and fracture toughness of steels and alloy steels. But application of ESR to aluminium alloys is only a recent endeavour. A high-strength aircraft aluminium alloy IS: 7670 was therefore chosen for studies on the fatigue strength and the impact and fracture toughness. The results indicate that the fatigue resistance is considerably improved after refining and that the impact strength and fracture toughness of the refined alloy are comparable with that of the unrefined alloy.

Microwave Irradiation Assisted Method for the Rapid Synthesis of fine Particles of alpha Al2O3 And alpha (Al1-XCrx)(2)O-3 And Their Coatings on Si(100)

Chromium substituted beta diketonate complexes of aluminium have been synthesized and employed as precursors for a novel soft chemistry process wherein microwave irradiation of a solution of the complex yields within minutes well crystallized needles of alpha (Al1 XCrx)(2)O-3 measuring 20 30 nm in diameter and 50 nm long By varying the microwave irradiation parameters and using a surfactant such as polyvinyl pyrrolidone the crystallite size and shape can be controlled and their agglomeration prevented These microstructural parameters as well as the polymorph of the Cr substituted Al2O3 formed may also be controlled by employing a different complex Samples of alpha (Al1 XCrx)(2)O-3 have been characterized by XRD FTIR and TEM The technique results in material of homogeneous metal composition, as shown by EDAX and can be adjusted as desired The technique has been extended to obtain coatings of alpha (Al1 XCrx)(2)O-3 on Si(100)

Onttojen puiden lahopuukovakuoriaiset — kolmen pyydystyypin vertailu

Vanhat ja ontot puut ovat tärkeä elinympäristö monelle lahopuusta riippuvaiselle eliölajille. Onttoihin puihin on erikoistunut suuri määrä myös vaarantuneita ja harvinaisia hyönteislajeja, jotka elävät puun onkalon seinämillä tai onkalon pohjalle kerääntyvässä orgaanisessa aineksessa, ns. mulmissa. Tutkimuksen tavoitteena oli selvittää, mikä kolmesta pyydystyypistä (ikkuna-, vuoka- ja kuoppapyydys) soveltuu parhaiten onttojen puiden lahopuukovakuoriaisten pyyntiin. Lisäksi tavoitteena oli kartoittaa hyönteisnäytteiden ensimmäiseen laboratoriokäsittelyyn vaadittua aikaa. Tutkimuksessa oli mukana vanhoja rungostaan onttoutuneita lehmuksia, tammia ja vaahteroita pääkaupunkiseudun puisto- ja kartanoalueilta. Puiden onkaloiden sisään aseteltiin ikkuna-, vuoka- ja kuoppapyydyksiä, kaksi kutakin tyyppiä ja ne tyhjennettiin kolmen viikon välein touko-heinäkuussa 2006. Pyydyksiä oli siis yhteensä 90 per pyyntijakso. Kun näytteistä eroteltiin halutut hyönteislahkot (mukaanlukien kovakuoriaiset) niiden käsittelyyn käytetty aika kirjattiin ylös. Aineistosta tunnistettiin yhteensä 3825 kovakuoriaisyksilöä ja 212 lajia, joista lahopuusta riippuvaisia oli yhteensä 3398 yksilöä ja 121 lajia. Ikkunapyydyksissä esiintyi yhteensä 1639 yksilöä ja 140 lajia, vuokapyydyksissä 1506 yksilöä ja 134 lajia, kuoppapyydyksissä 680 yksilöä ja 111 lajia. Näytteiden käsittelyaikojen keskiarvot olivat 48,3 minuuttia ikkunapyydykselle, 65,5 minuuttia vuokapyydykselle ja 34,1 kuoppapyydykselle. Lajistokoostumuksen huomioiva ?-diversiteetti erosi huomattavasti pyydysten välillä, se oli 36,5 % ikkuna- ja vuokapyydysten välillä, 13,1 % ikkuna- ja kuoppapyydysten välillä ja 14,2 % vuoka- ja kuoppapyydysten välillä. Ikkuna- ja vuokapyydysten välillä ei havaittu tilastollisesti merkitsevää eroa saproksyylilajien (p<0,05), -yksilöiden (p<0,05) tai käsittelyaikojen (p<0,05) keskiarvoissa. Ikkuna- ja vuokapyydyksillä saatiin keskimäärin selvästi enemmän saproksyylilajeja ja –yksilöitä kuoppapyydykseen verrattuna. Kuoppapyydyksellä saatiin kokonaisyksilömäärään verrattuna suhteellisesti vähemmän saproksyylejä (59 %) kuin ikkuna- (69 %) ja vuokapyydyksillä (71 %). Ikkunapyydykset olivat tehokkain pyydystyyppi vertailtaessa pyydysten keräämää saproksyyliyksilömäärää suhteessa aineiston käsittelyn vaatimaan aikaan. Tehokkuus (yksilöä minuutissa) ikkunapyydykselle oli 0,74, vuokapyydykselle 0,43 ja kuoppapyydykselle 0,21. Ikkunapyydyksiä ei ole aikaisemmin käytetty puun onkalon sisällä hyönteisiä pyydettäessä vaan ne ovat aikaisemmissa tutkimuksissa roikkuneet onkalon ulkopuolella. Ikkunapyydykset kuitenkin toimivat erinomaisesti myös onkaloiden sisällä. Ikkuna- sekä vuokapyydys toimivatkin selkeästi paremmin lahopuukovakuoriaisten pyynnissä verrattuna kuoppapyydykseen, jonka poisjättäminen olisi kuitenkin tuottanut huomattavasti lajiköyhemmän aineiston. Mahdollisimman monimuotoisen onttojen puiden lahopuukovakuoriaislajiston keräämiseksi tulisi käyttää ikkuna- tai vuokapyydyksiä yhdessä kuoppapyydysten kanssa.

Influence of Circular Defects on the Flexural Strength of Kevlar/Epoxy Composites

The flexural strength of the Kevlar/epoxy composite laminates, in the pres ence of unfilled and filled circular defects, was studied. Circular drillings of two different diameters extending up to the neutral axis from the compression face as well as through holes, at three different positions from the midspan, have been considered as simplified cases of dents and defects. Bonded buttons of aluminium metal have been tested and shown to yield a strength-wise compensation for test samples with depressions. Macrography of the failed specimens is also discussed.

Dynamic analysis of three point bend specimens under impact

A simple one dimensional inertial model is presented for transient response analysis of notched beams under impact, and extracting dynamic initiation toughness values. The model includes the effects of striker mass interactions, and contact deformations of the beam. Displacement time history of the striker mass is applied to the model as forcing function. The model is validated by comparison with the experimental investigation on ductile aluminium 6061 alloy and brittle polymer, PMMA.

Observation of asymmetry in U�I characteristics of contacts of the form metal 1�superconductor�metal 2

During experiments carried out to find out a suitable contact metal for electronic components based on high-T(c) superconductor films (Y-Ba-Cu-O), it is observed that there is an asymmetry in the U-I characteristics if the two contacts are made of different metals. The asymmetry is more pronounced if one of the contact metals is aluminium. The asymmetry is lowest if one of the contact metals is silver and the other gold.

Recombinant mid gut antigen (Bm95) as a vaccine against Indian Rhiphicephalus haemaphysaloides in Bos indicus cattle

In the present study, we report for the first time the efficacy of recombinant Bm95 mid gut antigen isolated from an Argentinean strain of Rhipicephalus microplus strain A in controlling the tick infestations in India. The synthetic gene for Bm95 optimized for expression in yeast was obtained and used to generate yeast transformants expressing Bm95 which was purified to apparent homogeneity. Liquid chromatography-mass spectrometry analysis of the purified protein confirmed its identity as Bm95. Vaccine was prepared by blending various concentrations of purified Bm95 with aluminium hydroxide as an adjuvant. lmmunogenicity studies of the vaccine in rabbits and cattle indicated that the vaccine was highly immunogenic. The efficacy studies of the vaccine was done in cattle. Naive Bos indicus cattle were vaccinated with the recombinant vaccine and were challenged with the larval, nymphal and adult forms of Rhiphicephalus haemaphysaloides. The vaccine protected the animals from larval, nymph and adult tick challenges with an efficacy of 98.7%, 84.6% and 78.9% respectively. The results obtained from the above studies clearly demonstrated the advantage and possibilities of the use of Bm95 in controlling R. haemaphysaloides infestations in the field. (C) 2010 Elsevier Ltd. All rights reserved.

A study of microstructure and wear behaviour of TiB2/Al metal matrix composites

The present paper deals with the study of microstructure and wear characteristics of TiB2 reinforced aluminium metal matrix composites (MMCs). Matrix alloys with 5, 10 and 15% of TiB2 were made using stir casting technique. Effect of sliding velocity on the wear behaviour and tribo-chemistry of the worn surfaces of both matrix and composites sliding against a EN24 steel disc has been investigated under dry conditions. A pin-on-disc wear testing machine was used to find the wear rate, in which EN24 steel disc was used as the counter face, loads of 10-60N in steps of 10N and speeds of 100, 200, 300, 400 and 500 rpm were employed. The results showed that the wear rate was increased with an increase in load and sliding speed for both the materials. However, a lower wear rate was obtained for MMCs when compared to the matrix alloys. The wear transition from slight to severe was presented at the critical applied loads. The transition loads for the MMCs were much higher than that of the matrix alloy. The transition loads were increased with increase in TiB2 and the same was decreased with the increase of sliding speeds. The SEM and EDS analyses were undertaken to demonstrate the effect of TiB2 particles on the wear mechanism for each conditions.