Erbium and ytterbium co-doped SiO2 : GeO2 planar waveguide prepared by the sol-gel route using an alternative precursor

The sol-gel method combined with a spin-coating technique has been successfully applied for the preparation of rare-earth doped silica:germania films used for the fabrication of erbium-doped waveguide amplifiers (EDWA), presenting several advantages over other methods for the preparation of thin films. As with other methods, the sol-gel route also shows some drawbacks, such as cracks related to the thickness of silica films and high hydrolysis rate of certain precursors such as germanium alkoxides. This article describes the preparation and optical characterization of erbium and ytterbium co-doped SiO2:GeO2 crack-free thick films prepared by the sol-gel route combined with a spin-coating technique using a chemically stable non-aqueous germanium oxide solution as an alternative precursor. The non-crystalline films obtained are planar waveguides exhibiting a single mode at 1,550 nm with an average thickness of 3.9 mu m presenting low percentages of porosity evaluated by the Lorentz-Lorenz Effective Medium Approximation, and low stress, according to the refractive index values measured in both transversal electric and magnetic polarizations. Weakly confining core layers (0.3% < Delta n < 0.75%) were obtained according to the refractive index difference between the core and buffer layers, suggesting that low-loss coupling EDWA may be obtained. The life time of the erbium I-4(13/2) metastable state was measured as a function of erbium concentration in different systems and based on these values it is possible to infer that the hydroxyl group was reduced and the formation of rare-earth clusters was avoided.

Effects of caffeine and used coffee grounds on biological features of Aedes aegypti (Diptera, Culicidae) and their possible use in alternative control

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Alternative paths for insertion of probes into high inclination lunar orbits

The dynamics of the restricted three-body Earth-Moon-particle problem predicts the existence of direct periodic orbits around the Lagrangian equilibrium point L1. From these orbits, we derive a set of trajectories that form links between the Earth and the Moon and are capable of performing transfers between terrestrial and lunar orbits, in addition to defining an escape route from the Earth-Moon system. When we consider a more complex and realistic dynamical system - the four-body Sun-Earth-Moon-particle (probe) problem - the trajectories have an expressive gain of inclination when they penetrate in the lunar influence sphere, thus allowing the insertion of probes into low-altitude lunar orbits with high inclinations, including polar orbits. In this study, we present these links and investigate some possibilities for performing an Earth-Moon transfer based on these trajectories. (C) 2007 COSPAR. Published by Elsevier Ltd. All rights reserved.

Numerical study about natural escape and capture routes by the Moon via Lagrangian points L1 and L2

The lunar sphere of influence, whose radius is some 66,300 km, has regions of stable orbits around the Moon and also regions that contain trajectories which, after spending some time around the Moon, escape and are later recaptured by lunar gravity. Both the escape and the capture occur along the Lagrangian equilibrium points L1 and L2. In this study, we mapped out the region of lunar influence considering the restricted three-body Earth-Moon-particle problem and the four-body Sun-Earth-Moon-particle (probe) problem. We identified the stable trajectories, and the escape and capture trajectories through the L I and L2 in plots of the eccentricity versus the semi-major axis as a function of the time that the energy of the osculating lunar trajectory in the two-body Moon-particle problem remains negative. We also investigated the properties of these routes, giving special attention to the fact that they supply a natural mechanism for performing low-energy transfers between the Earth and the Moon, and can thus be useful on a great number of future missions. (C) 2007 Published by Elsevier Ltd on behalf of COSPAR.

Alternative methodologies for the determination of aldehydes by capillary electrophoresis

This paper describes 2 alternative methodologies for the determination of selected aldehydes (formaldehyde, acetaldehyde, propionaldehyde, acrolein, and benzaldehyde) by capillary electrophoresis (CE), the first approach is based on the formation of aldehyde-bisulfite adducts and employs free solution CE with reversed electroosmotic flow and indirect detection, using 10 mmol/L 3,5-dinitrobenzoic acid (pH 4.5) containing 0.2 mmol/L cetyltrimethylammonium bromide as the electrolyte. This novel methodology showed a fairly good sensitivity to concentration, with detection limits with respect to a single aldehyde on the order of 10-40 mu g/L, a reasonable analysis time (separation was achieved in <8 min), and no need for sample manipulation. A second approach was proposed in which 2,4-dinitrophenylhydrazine derivatives of the aldehydes were detected in a micellar electrolyte medium (20 mmol/L berate buffer containing 50 mmol/L sodium dodecyl sulfate and 15 mmol/L beta-cyclodextrin). This latter methodology included a laborious sample preconcentration step and showed much poorer sensitivity (0.5-2 mg/L detection limit, with respect to a single aldehyde), despite the use of sodium chloride to promote sample stacking. Both methodologies proved adequate to evaluate aldehyde levels in vehicular emissions. Samples from the tailpipe exhaust of a passenger car vehicle without a catalytic converter and operated with an ethanol-based fuel were collected and analyzed; the results showed high levels of formaldehyde and acetaldehyde (0.41-6.1 ppm, v/v). The concentrations estimated by the 2 methodologies, which were not in good agreement, suggest the possibility of striking differences in sample collection efficiency, which was not the concern of this work.

THE USE OF AMPPD AS AN ALTERNATIVE SUBSTRATE FOR AP-MEDIATED DETECTION OF NONRADIOLABELED DNA PROBES IN EUCALYPTUS-SALIGNA

We present a non-radioactive alternative to Southern's (J. Mol. Biol. 98: 503-517, 1975) DNA-DNA hybridization technique. The use of AMPPD - Disodium 3-(4-Methoxyspiro {1,2-dioxetane-3,2'tricyclo[3.3.1.1(3,7)]decan}-4-yl)phyenyl phosphate as an alternative substrate for AP-mediated detection of digoxigenin-11 dUTP-labeled probes made possible the simple and nonhazardous reuse of blots. We used 0.8 % agarose gels containing 30 mug per lane of Eucalyptus saligna DNA, digested with Eco RI, electrophoresed and blotted on to nylon membranes (Hybond-N, Amersham, UK), using the Southern blotting procedure, and UV irradiated for one minute for DNA fixation. The hybridizations were carried out overnight with digoxigenin labeled random inserts of E. saligna DNA by using the Genius Kit (Boehringer Mannheim). Detection of the DNA-DNA hybrids was performed in the presence of 0.5% blocking agent and the substrates NBT/BCIP were replaced by 0.26 mM AMPPD in the final alkaline assay buffer (50 mul/cm2). After membrane incubation for five minutes at room temperature in a sealed plastic bag, the AMPPD solution was retrieved and stored at 4-degrees-C for reuse. A Kodak X-BRAF QA-S film was pressed firmly onto the bag containing the wet membrane, exposed for two to six hours and then developed. After use, the probes were stripped off and the blots reutilized, three times so far, with the same results.

Antibiosis associated to Lactobacillus acidophilus growth .1. Strain selection and study of an alternative medium using whey

The production of antimicrobial compounds of some strains of Lactobacillus acidophilus has been studied. They have been grown in whey supplemented with soy milk. It has been found that the production of compounds is able to inhibit the growing of both target bacteria analysed: Staphylococcus aureus and Escherichia coli. The results showed a significant variation (p>0.05) depending on the strain of L. acidophilus and on the level of supplementation utilized. Most of the inhibition observed resulted from the presence of the lactic acid produced. It has also been found the production of other antimicrobial compounds showing inhibitory capacity. The action of these compounds was influenced by the substract pH.

Study of alternative schemes for the parameterization step of the continuation power flow method based on physical parameters, part I: Mathematical modeling

The conventional power flow method is considered to be inadequate to obtain the maximum loading point because of the singularity of Jacobian matrix. Continuation methods are efficient tools for solving this kind of problem since different parameterization schemes can be used to avoid such ill-conditioning problems. This paper presents the details of new schemes for the parameterization step of the continuation power flow method. The new parameterization options are based on physical parameters, namely, the total power losses (real and reactive), the power at the slack bus (real or reactive), the reactive power at generation buses, and transmission line power losses (real and reactive). The simulation results obtained with the new approach for the IEEE test systems (14, 30, 57, and 118 buses) are presented and discussed in the companion paper. The results show that the characteristics of the conventional method are not only preserved but also improved.