投加溶胞菌群对剩余污泥消化影响的初步研究

活性污泥法是目前世界上普遍应用的污水生物处理工艺，其在运行过程中产生大量的剩余污泥。由于剩余污泥处理费用巨大及污泥最终处置对环境具有潜在危害问题，污泥的处理和处置已经成为水处理领域关注的焦点。本文利用实验室筛选的溶胞菌群，在好氧消化的同时对污泥进行前处理，促进剩余污泥的破解与溶胞，再通过两相厌氧处理对污泥进行进一步消化，以研究投加溶胞菌对剩余污泥消化的影响。 本研究中溶胞菌污泥减量化技术分为两个部分，第一，污泥在溶胞菌作用下的好氧消化与污泥传统好氧消化的对比研究，利用取自成都三瓦窑污水处理厂剩余污泥，向好氧污泥消化反应器中投加溶胞菌，检测各项污泥指标，并通过同传统好氧污泥消化对比，以研究溶胞菌对污泥好氧消化的影响。第二， 经过溶胞菌处理后好氧消化的剩余污泥进行两相厌氧处理研究。通过建立好氧溶胞联合两相厌氧消化系统的来处理剩余污泥，并与相同条件运行的两相厌氧消化系统做对比，检测运行过程中系统中物质成分变化，研究了其处理能力和运行稳定性，探索了两相厌氧消化系统中的发酵类型差别，验证了好氧溶胞对剩余污泥的破解效果。 研究结果表明：污泥在溶胞菌作用下的好氧消化效果和消化效率均优于传统好氧消化。在溶胞菌群存在的情况下，剩余污泥的TSS和VSS去除率达到40%和53%，远高于传统好氧消化的12%和20%。污泥经过溶胞及好氧消化后，TCOD去除率达到54.4%。经过溶胞菌处理后的剩余污泥再进入两相厌氧处理系统，进入厌氧处理系统的剩余污泥的VSS／TSS比值约为0.62。在两相厌氧处理水力停留时间(HRT)为8d时，溶胞处理污泥厌氧消化后VSS去除率达到55.17%，对照组两相厌氧系统的VSS去除率平均值为18.53%。经过溶胞处理的两相厌氧系统的污泥减量了能力远高于对照组。两相厌氧系统的pH值和碱度说明系统运行较为稳定。产酸相的有机酸中乙酸含量高于丙酸和丁酸，说明发酵末端产物以乙酸为主。在20天的试验周期内，污泥溶胞处理后、两相厌氧系统产甲烷相产气量累积产气量为1.2L，对照组只有375ml。气体中甲烷含量都在55%左右。该研究结果表明，好氧溶胞对污泥有破解能力，溶胞处理对两相厌氧中产酸相水解污泥细胞有明显的促进作用，提高了产酸相的水解酸化能力和效率。该研究对于利用生物溶胞途径提高污泥消化效率具有重要意义。 The actived sludge process has been used more and more extensively, but the procedure will lead to a large quantity of excess sludge. The treatment of Excess activated sludge has becomes a focuses not only for it is a seriously negative effect on environment but also for the costly disposal comes subsequently. The cell lysing bacterium was keeped in our lab to joined in the digestion of the excess activated sludge which was carrying at the same time with pre-processing of sludge to investigated the influence of cell lysing bacterium on excess sludge. There are two part in the method of cell lysing bacterium digesting sludge technology, the first, comparison of excess sludge digestion between anaerobic Cell-lysing Pretreatment and Conventional Aerobic Process. The sludge which was collected from San Wanyao disposal plant in Chengdu was thrown into the aerobic process system with cell-lysing bacterium, then, the indexes were detected to compare the difference between the cell-lysing bacterium in aerobic process and the traditional method to determine the influence of cell-lysing bacterium on aerobic process ; The second, the research on the sludge which was pro-treated with cell-lysing and aerobic digestion in the diphase of anaerobic digestion system. The system of cell-lysing combined with diphase of anaerobic digesting was created to compare to the diphase of anaerobic digested system, the changes of mass constituent was detected to study the ability and steady of disposal. Moreover, the research explored the difference among the types of fermentation. The efficacious of aerobic process was been proved. The result shows that the digesting rate of aerobic process with cell-lysing bacterium was higher than the traditional process. The ratio of sludge is reach to 40%~53%, which was far more effectively than the traditional process rate of 12%~20%. The TCOD of sludge which was treated with cell lysing bacterium and Aerobic Process is reach to 54.4%. Then, the sludge was thrown into the diphase of anaerobic digesting system. VSS／TSS of sludge is 0.62, HRT is 6d, the reduction of VSS is reach to 40.8%. The pH and alkalinity indicate the steady running of the diphase anaerobic digest system. In the acerbity phasing, the content of acetic acid was more than butanoic acid and propanoic acid in organic acid, it is demonstrated that the main composition of final production of fermentation was Acetic Acid. During the 20d of experiment, methylhydride phasing of diphase anaerobic digest system produced 1.2L methylhydride, however, there is only 375ml in CK, the content of methylhydride in all gas phase was around the rate of 55%. The average ratio of VSS was 18.53% in CK diphase anaerobic digest system which was far more unavailable than the mass sludge rate of 55.17%. Results demonstrated that aerobic cell-lysing digested the sludge, the treat of cell-lysing could obviously promoted the hydrolyzeing of sludge cell in the acerbity phasing, which improved the ability and rate of hydrolization and acidification. This study is significant in inhenceing the rate of sludge digestion in the method of cell-lysing bacterium.

制革废水生物强化处理及中水回用试验研究

制革行业是轻工行业中仅次于造纸业的高耗水、重污染行业，作为劳动密集型行业，在解决大量人口就业问题的同时，也对所在地区环境造成了严重污染。目前我国制革行业每年排放废水8,000~12,000万吨，废水中含铬约3,500 t，SS为1.2×105 t，COD为1.8×105 t，BOD为7×104 t，对水体污染严重。 本研究在对厌氧酸化工艺进行研究、一级好氧处理段进行工艺比选研究的基础上，获得了匀质调节—SBBR—BAF的生物处理工艺，并依托该工艺进行了生物强化处理的研究，考察了菌剂的强化运行效果及其处理水回用的可行性。 研究表明，在进水COD＞3,000 mg/L，厌氧酸化具有很好的抗冲击作用，保证了好氧工艺出水COD＜200 mg/L；在进水COD＜3,000 mg/L，可只通过好氧处理实现出水COD＜200 mg/L。厌氧酸化停留时间选择不当，会导致厌氧出水硫化物浓度升高，严重影响好氧系统，会使好氧活性污泥因中毒而解絮。 研究表明，当进水COD为2,000~2,500 mg/L，NH4+-N为130~146 mg/L时，COD、NH4+-N去除率SBBR分别为93.8%~96.6%和14.5%~55.9%，SBR分别为88.8%~94.9%和13%~50.7%，表明SBBR优于SBR。同时，研究发现SBBR污泥增长率为0.05 kgVSS/kgCOD，仅为SBR0.57 kgVSS/kgCOD的8.8%。此外，研究发现SBBR在停止运行后经3个运行周期可回复原油能力，而SBR池经9个周期培养也不能恢复，说明SBBR恢复能力明显优于SBR。 研究表明，以匀质调节—SBBR—BAF为主的制革废水处理工艺，出水水质稳定，进水COD 801~2,834 mg/L、NH4+-N 87~203 mg/L，出水COD＜80 mg/L、NH4+-N＜10 mg/L，基本达到中水回用标准；操作简单灵活，没有污泥回流系统，污泥产率低，污泥处理费用低；工艺基本不需要添加化学药剂，既节约成本、又避免了二次污染；两级生物膜使得该工艺具有很强的耐冲击负荷能力，特别适合制革废水水质水量波动大的特点。 研究表明，高效菌对系统的启动具有一定的促进作用，强化系统生物膜6天可以成熟，对照系统生物膜9天可以成熟。同时高效菌能加速COD降解，缩短停留时间，强化系统6~8 h可使COD＜200 mg/L，对照系统8~10 h可使COD＜200 mg/L。长期运行表明，强化系统的SBBR在COD和NH4+-N的去除率都优于对照系统的SBBR。最终出水COD强化系统平均为53 mg/L、对照系统为74 mg/L。在模拟循环过程中，强化系统均有更高的稳定性。可实现8次理论循环，而对照系统只能实现4次理论循环。 研究表明，通过合理的工艺设计，可以实现猪皮制革废水达到《污水综合排放标准GB8976-1996》一级标准，同时满足工厂部分用水要求。通过添加高效微生物，可提高生物处理系统处理能力，使处理水能够满足工厂的多次回用。 As a labour-intensive industry, tanning has created large amount of working opportunities as well as caused severe contamination to environment. And it is one of the highest water-consuming and polluting industry, only second to manufacturing. At present time, Chinese leather industry emits wastewater about 80,000,000~120,000,000 t annually, which contains chromium about 3,500 t, SS 1.2×105 t, COD 1.8×105 t, BOD 7×104 t and ambient riverhead has been polluted greatly. Based on the research of anaerobic acidification and comparison of SBBR and SBR, biotreatment process (Homogenization—SBBR—BAF) had been established to amend the disadvantages of traditional sewage treatment such as too much sludge, high cost of advanced treatment and NH4+-N can not reach the emission standard. Research on the bioaugmentation was also been carried out. Researches showed, when COD of influent was beyond 3,000 mg/L, anaerobic acidification could resist strong impact, thus COD of effluent was less than 200 mg/L; when COD of influent was less than 3,000 mg/L, only throughout aerobic sewage treatment could COD of effluent beless than 200 mg/L. False residence tiome of anaerobic acidification would lead to the higher effluent concentration of sulfide and disintegration of aerobic activated sludge. Researches showed SBBR worked a better than SBR: when influent between 2,000 and 2,500 mg/L, NH4+-N between 130 mg/L and 146 mg/L, COD, NH4+-N removal rate of SBBR was 93.3%~96.6%, 14.5%~55.9% respectively while COD, NH4+-N removal rate of SBR was 88.8%~94.9%, 13%~50.7% respectively. Sludge growth rate of SBBR was 8.8% of that of 0.05 kgVSS/kgCOD. Besides, SBBR could recovered after 3 operating periods while SBR worked no better after 9 operating periods.Therefore, SBBR excelled SBR. Researches showed, effluent quantity of tannery wastewater treatment process (Homogenization—SBBR—BAF) was stable. When COD of influent was between 801 and 2,834 mg/L, NH4+-N was between 87 mg/L and 203 mg/L, COD of effluent was less than 80 mg/L, NH4+-N was less than 10 mg/L, which achieved the standard of reuse. This biotreatment was featured in low cost, easy and flexible management, less sludge, no inverse sludge system. Besides, this technique required no chemical, which could lower the cost and avoid secondary pollution. Great resistant of impact due to two membranes and was suitable for tannery wastewater which was featured by fluctuation of influent quality and quantity. Researches showed effective microorganisms promotes the startup of the process.Biofilm in the bioaugmentation process matured with 6 days while biofilm in normal process matured with 9 days. Effective microorganisms could accelerate the degradation of COD and shorten the residence time. Aggrandizement system could make COD<200 mg/L with 6 to8 hours while cntrolling system could make COD<200 mg/L with 8 to 10 hours. Long-term operating shows that SBBR in the bioaugmentation system worked better than the normal system in the treatment of COD and NH4+-N. The average COC of effluent in bioaugmentation system was 53 mg/L, normal system was 74 mg/L. In the simulative circulation process,aggrandizement process, which could fulfill 8 times theoretical circulation, works more stably than controlling process which could only fulfill 4 times theoretical circulation. Researches showed that reasonable design could make the wastewater meet the first grade of discharging standard of National Integrated Wastewater Discharge Standard (GB8976-1996), and partially meet the demand of water using of the factory. Adding effective microorganisms could enhance the biotreatment and make the effluents reuse many times.

Effects of Ionizing Radiation on Three-Dimensional Human Vessel Models: Differential Effects According to Radiation Quality and Cellular Development

Little is known about the effects of space radiation on the human body. There are a number of potential chronic and acute effects, and one major target for noncarcinogenic effects is the human vasculature. Cellular stress, inflammatory response, and other radiation effects on endothelial cells may affect vascular function. This study was aimed at understanding the effects of space ionizing radiation on the formation and maintenance of capillary-like blood vessels. We used a 3D human vessel model created with human endothelial cells in a gel matrix to assess the effects of low-LET protons and high-LET iron ions. Iron ions were more damaging and caused significant reduction in the length of intact vessels in both developing and mature vessels at a dose of 80 cGy. Protons had no effect on mature vessels up to a dose of 3.2 Gy but did inhibit vessel formation at 80 cGy. Comparison with gamma radiation showed that photons had even less effect, although, as with protons, developing vessels were more sensitive. Apoptosis assays showed that inhibition of vessel development or deterioration of mature vessels was not due to cell death by apoptosis even in the case of iron ions. These are the first data to show the effects of radiation with varying linear energy transfer on a human vessel model. (C) 2011 In Radiation Research Society

Control of cocklebur seed germination by nitrogenous compounds : Nitrite, nitrate, hydroxylamine, thiourea, azide and cyanide

Germination of non-dormant upper cocklebur (Xanthium pinsylvanicum Wallr.) seeds was stimulated by not only CS(NH2)2 but also NH2OH, KCN and NaN3. This stimulation was not via the enhancement of aerobic C2H4 production. NH2OH, KCN and NaN3 in certain concentrations promoted the initial growth of axial and/or cotyledonary parts, but the degree of growth promotion by NH2OH, NaN3 and KCN was slight compared with that by CS(NH2)2. As in the case of CS(NH2)2, however, the germinationstimulating effect of NH2OH disappeared rapidly as the preceding imbibition period was prolonged. In contrast, KCN and NaN3 were still effective in stimulating the germination of aged seeds maintained on a water substratum, as previously seen with anaerobiosis. Anaerobic induction was enhanced not only by NaN3 and KCN but also by NH2OH, KNO3, KNO2 CO(NH2)2 and CS(NH2)2 applied during the anaerobic treatment, but without causing an increase in anaerobic production of C2H4. Furthermore, KCN and NaN3, given prior to the anaerobic treatment acted additively with anaerobic induction. The germination-stimulating actions of nitrogenous compounds are discussed in comparison with those of C2H4 and anaerobiosis.

Profiling of Complex Microbial Populations by Denaturing Gradient Gel Electrophoresis Analysis of Polymerase Chain Reaction-Amplified Genes Coding for 16S rRNA

We describe a new molecular approach to analyzing the genetic diversity of complex microbial populations. This technique is based on the separation of polymerase chain reaction-amplified fragments of genes coding for 16S rRNA, all the same length, by denaturing gradient gel electrophoresis (DGGE). DGGE analysis of different microbial communities demonstrated the presence of up to 10 distinguishable bands in the separation pattern, which were most likely derived from as many different species constituting these populations, and thereby generated a DGGE profile of the populations. We showed that it is possible to identify constituents which represent only 1% of the total population. With an oligonucleotide probe specific for the V3 region of 16S rRNA of sulfate-reducing bacteria, particular DNA fragments from some of the microbial populations could be identified by hybridization analysis. Analysis of the genomic DNA from a bacterial biofilm grown under aerobic conditions suggests that sulfate-reducing bacteria, despite their anaerobicity, were present in this environment. The results we obtained demonstrate that this technique will contribute to our understanding of the genetic diversity of uncharacterized microbial populations.

中国洪涝灾害之后的生态环境问题警钟急鸣

中国是一个发展中国家 ,正在加速实现工业化、城市化及农业现代化。由于人们的生产活动和经济活动而对生态环境的破坏“助纣为虐” ,才使 1 998年的洪水造成的损失比以往更大 ,并进一步暴露出以城市为中心的环境污染和以农村为纽带的环境退化正破坏和延缓我国国民经济的发展。分析了洪灾之后中国经济发展中环境面临的主要问题和退化症结 ,根据 2 0 1 0年远景目标的要求 ,提出了“提高环保认识 ,开展生态建设 ,控制环境污染”的综合整治对策 ,为中国制定生态环境规划提供基本思路。

延安试区土壤干层现状分析

近年来 ,以林草地地力衰退为特征的人工林草地土壤退化日趋严重 ,其中以土壤水分严重亏缺为特征的土壤干化现象愈益引起了人们的重视。土壤干化的直接后果是形成土壤干层 ,导致土壤退化 ,植物生长速率减缓 ,群落衰败以至大片死亡 ,严重地威胁到中国中北方地区特别是黄土高原地区生态环境的建设。因此 ,研究和解决土壤干层问题已成为黄土高原植被建设的迫切任务。根据现有土壤水分资料 ,初步分析了延安试区植被下的土壤干层现状 ,对不同林草植被下的干层状况做了比较 ,并提出了解决土壤干层问题的意义

水土流失是生态环境恶化的根源

阐述水土流失的基本概况、主要原因及其严重危害 ,提出应采取的防治措施。

延安试区人工刺槐林地的土壤干层分析

8 0年代以来 ,以林草地地力衰退为特征的人工林草地土壤退化日趋严重 ,其中以土壤水分严重亏缺为特征的土壤干化现象愈益引起了人们的重视。土壤干化的直接后果是形成土壤干层 ,导致土壤退化 ,植物生长速率减缓 ,群落衰败以至大片死亡 ,严重地威胁到我国北方地区特别是黄土高原地区生态环境的建设。因此 ,研究和解决土壤干层问题已成为黄土高原植被建设的迫切任务。根据延安试区的土壤水分和植被生长状况调查资料 ,初步分析了不同条件下刺槐人工林地的水分状况。结果表明 :试区刺槐人工林地普遍形成了土壤干层 ,且已相当严重 ;坡向对土壤干层有明显影响 ,阳坡形成的干层较阴坡严重 ;坡度愈大 ,土壤干化愈剧烈 ;林龄对干层严重程度影响不明显。同时 ,研究指出了解决土壤干层问题的意义。

不同林龄植被培肥改良土壤效益研究

在黄土丘陵沟壑区森林植被能够明显改善生态环境 ,防止土地退化 ,提高土壤中有机质、速效氮和速效钾的含量 ,降低土壤pH和容重 ;快速显著地增加土体中 >0 .2 5mm水稳性团聚体和 >5 0 μm微团粒的数量 ,使土壤结构改善 ,协调供应养分和水分的能力提高 ;能促进黏粒形成 ,坚实度增加 ,土壤的抗蚀性和抗冲性提高 ,有效地减少水土流失。植被对土壤的培肥改良是一种正向持续反馈机制 ,时间越长 ,效益越显著

Selective hydrogenation of unsaturated aldehydes in a poly(ethylene glycol)/compressed carbon dioxide biphasic system

Hydrogenation of alpha,beta-unsaturated aldehydes (citral, 3-methyl-2-butenal, cinnamaldehyde) has been studied with tetrakis(triphenylphosphine) ruthenium dihydride (H2Ru(TPP)(4)) catalyst in a poly(ethylene glycol) (PEG)/ compressed carbon dioxide biphasic system. The hydrogenation reaction was slow under PEG/ H-2 biphasic conditions at H-2 4 MPa in the absence of CO2. When the reaction mixture was pressurized by a non-reactant of CO2, however, the reaction was significantly accelerated.

Effect of La-Mg-based alloy addition on structure and electrochemical characteristics of Ti0.10Zr0.15V0.35Cr0.10Ni0.30 hydrogen storage alloy

Effect of La-Mg-based alloy (AB(5)) addition on Structure and electrochemical characteristics of Ti0.10Zr0.15V0.35Cr0.10Ni0.30 hydrogen storage alloy has been investigated systematically. XRD shows that the matrix phase structure is not changed after adding AB(5) alloy, however, the amount of the secondary phase increases with increasing AB(5) alloy content. The electrochemical measurements show that the plateau pressure Ti0.10Zr0.15V0.35Cr0.10Ni0.30 + x% La0.85Mg0.25Ni4.5Co0.35Al0.15 (X = 0, 1, 5, 10, 20) hydrogen storage alloys increase with increasing x, and the width of the pressure plateau first increases when x increases from 0 to 5 and then decreases as x increases further, and the maximum discharge capacity changes in the same trend.

Effect of AB(5) alloy on Ti0.10Zr0.15V0.35Cr0.10Ni0.30 hydrogen storage alloy

The structure and electrochemical characteristics of melted composite Ti0.10Zr0.15V0.35Cr0.10Ni0.30 + x% LaNi4Al0.4Mn0.3Co0.3 (x = 0, 1, 5) hydrogen storage alloys have been investigated systematically. XRD shows that though the main phase of the matrix alloy remains unchanged after LaNi4Al0.4Mn0.3Co0.3 alloy is added, a new specimen is formed. The amount of the new specimen increases with increasing x. SEM-EDS analysis indicates that the V-based solid solution phase is mainly composed of V, Cr and Ni; C14 Laves phase is mainly composed of Ni, Zr and V; the new specimen containing La is mainly composed of Zr, V and Ni. The electrochemical measurements suggest that the activation performance, the low temperature discharge ability, the high rate discharge ability and the cyclic stability of composite alloy electrodes increase greatly with the growth of x.

Theoretical studies on the reaction mechanism of oxidation of primary alcohols by Zn/Cu(II)-phenoxyl radical catalyst

The catalytic mechanism for the oxidation of primary alcohols catalyzed by the two functional models of galactose oxidase (GOase), M-II L (M = Cu, Zn; L = N,N'-bis(3,5-di-tert-butyl-2-hydroxyphenyl)1-2-diiminoquinone)), has been studied by use of the density functional method B3LYP The catalytic cycle of Cu- and Zn-catalysts consists of two parts, namely, substrate oxidation (primary alcohol oxidation) and O-2 reduction (catalyst regeneration). The catalytic mechanisms have been studied for the two reaction pathways (route 1 and route 2). The calculations indicate that the hydrogen atom transfer within the substrate oxidation part is the rate-determining step for both catalysts, in agreement with the experimental observation.

Influence of Annealing on Microstructure and Mechanical Properties of Isotactic Polypropylene with beta-Phase Nucleating Agent

The microstructure and mechanical properties of beta-nucleated iPP before and after being annealed at different temperatures (90-160 degrees C) have been analyzed, Annealing induced different degrees of variation in fracture toughness of beta-nucleated iPP samples. namely, slight enhancement at relatively low annealing temperatures (< 110 degrees C) and great improvement at moderate temperatures (120-130 degrees C), whereas dramatic deterioration at relatively high temperatures ( > 140 degrees C) has been observed. The variation of fracture toughness of beta-nucleated iPP is observed to be dependent on the content of beta-NA. Experiments, including scanning electronic microscope (SEM), wide-angle X-ray diffraction (WAXD), differential scanning calorimetry (DSC), small-angle X-ray scattering (SAXS), and dynamic mechanical analysis (DMA), are performed to study the variations of microstructures as well as the toughening mechanism of the beta-nucleated iPP after being annealed.