Precipitation and solute clustering in aluminium: advanced characterisation techniques

Recent development of characterisation techniques and computer simulation has extended our ability to access atomic scale information regarding materials microstructure evolution. New results from such techniques have significantly progressed our knowledge about solute behaviour during the earliest stages of decomposition of the solid solution. This chapter updates current understanding about solute clustering and discusses the effect of solute clustering and micro-alloying on precipitate microstructure evolution in aluminium alloys. In addition, a brief review is given on the effect of severe plastic deformation on precipitate evolution in Al alloys.

Fatigue crack growth in ultrafine grained aluminium alloy

The microstructure, fatigue crack growth behaviour and hardness of ultra fine grained 6061 aluminium alloy obtained by equal angle channel processing was studied. ECAP resulted in significant grain refinement down to the sub micron level and corresponding increase in hardness. Results point to a similar fatigue threshold stress intensity range and fatigue crack growth rates for 1, 2, 4 and 6 passes of ECAP.

Microstructure and electrical conductivity of aluminium/steel bimetallic rods processed by severe plastic deformation

Equal-channel angular pressing (ECAP) was used to fabricate Al/steel bimetallic rod for potential application in overhead transmission conductors. Bimetallic rods consisted of an austenitic stainless steel 316L core and an Al alloy 6201 cladding layer. By means of ECAP processing at 175°C, increase of mechanical strength without loss of electrical conductivity was achieved for one particular rod geometry out of three geometries tested. X-ray diffraction and transmission electron microscopy were employed to analyse how the microstructure was influenced by the number of processing passes and the bimetallic rod geometry. The co-deformation mechanism of the bimetallic rod under ECAP and accelerated dynamic ageing of Al alloy 6201 were discussed based on the microstructure characterisation results.

Electrical discharge machining of 6061 aluminium alloy

The wire electrical discharge machining (EDM) of 6061 aluminium alloy in terms of material removal rate, kerf/slit width, surface finish and wear of electrode wire for different pulse on time and wire tension was studied. Eight experiments were carried out in a wire EDM machine by varying pulse on time and wire tension. It is found that the material removal rate increases with the increase of pulse on time though the wire tension does not affect the material removal rate. It seems that the higher wire tension facilitates steady machining process, which generates low wear in wire electrode and better surface finish. The surface roughness does not change notably with the variation of pulse on time. The appearance of the machined surfaces is very similar under all the machining conditions. The machined surface contains solidified molten material, splash of materials and blisters. The increase of the pulse on time increases the wear of wire electrode due to the increase of heat input. The wear of wire electrode generates tapered slot which has higher kerf width at top side than that at bottom side. The higher electrode wear introduces higher taper.

Aluminium tolerance in bean traditional cultivars from Madeira

Common bean (Phaseolus vulgaris L.) is the most important legume crop in the world, providing low-cost, high quality protein, minerals and dietary fiber for human nutrition. The crop was originated from diversity centers in America and exhibits adaptation abilities to different environmental conditions, including soil with low pH. Acid soils occupy 30% of the agro ecosystem areas in the world. In Madeira, acid Andosols and unsatured Cambisols are the dominant groups of soils. Generally, under acidic and infertile conditions, besides of H+ toxicity, soluble aluminium (Al) is the most important abiotic factor limiting plant development and crop productivity. In the field, the hidden roots are also affected and the reduction of root growth under Al stress can be clearly observed in early stages. Seedlings of fifty bean accessions from the Archipelago of Madeira were tested under controlled conditions in the presence of 50 mM Al at pH 4.4. In general, the tested germplasm appeared to be sensitive or very sensitive to Al toxicity. However, fifteen traditional cultivars clearly exhibited elevated Al-tolerance, with an average root relative elongation (RRE) exceeding 50%, while top six accessions surpassed the 60% RRE mark. The Madeira bean germplasm is a valuable resource for sustainable crop production in acid soils and it could be used as parental lines in breeding programs aimed for Al tolerance in common beans.

Characterisation and investigation of local variations in mechanical behaviour in cast aluminium using gradient solidification, Digital Image Correlation and finite element simulation

Due to design and process-related factors, there are local variations in the microstructure and mechanical behaviour of cast components. This work establishes a Digital Image Correlation (DIC) based method for characterisation and investigation of the effects of such local variations on the behaviour of a high pressure, die cast (HPDC) aluminium alloy. Plastic behaviour is studied using gradient solidified samples and characterisation models for the parameters of the Hollomon equation are developed, based on microstructural refinement. Samples with controlled microstructural variations are produced and the observed DIC strain field is compared with Finite Element Method (FEM) simulation results. The results show that the DIC based method can be applied to characterise local mechanical behaviour with high accuracy. The microstructural variations are observed to cause a redistribution of strain during tensile loading. This redistribution of strain can be predicted in the FEM simulation by incorporating local mechanical behaviour using the developed characterization model. A homogeneous FEM simulation is unable to predict the observed behaviour. The results motivate the application of a previously proposed simulation strategy, which is able to predict and incorporate local variations in mechanical behaviour into FEM simulations already in the design process for cast components.

Premature thermal fatigue failure of aluminium injection dies with duplex surface treatment

The premature failure of an aluminium injection die with a duplex surface treatment (plasma nitriding and physical vapor deposition coating) was investigated, in an effort to identify the causes of such premature failure of the component. The manufacturing and the operating conditions were documented. Analytical tools were used, including scanning electron microscopy with energy dispersive X-ray capability, X-ray diffraction, and instrumented microhardness testing. Preliminary observations showed a microstructure of coarse tempered martensite, and a considerably rough surface with porosity and cracks. A detailed analysis of crack initiation sites identified sulfur inclusions in the subsurface, underneath the coating. A further revision of the processing conditions revealed that a sulfur-impregnated grinding stone had been used to polish the die. The chemical composition of such grinding stone matched that of the inclusions found in the subsurface of the failed component. Thus, searched causes of premature failure could be discussed on the lights of the present findings.

Prediction of failure in bending of an aluminium sheet alloy

This work is dedicated to numerical prediction of the bending of thin aluminium alloy sheets, with a focus on the material parameter identification and the prediction of rupture with or without pre-strains in tension prior to bending. The experimental database consists of i) mechanical tests at room temperature, such as tension and simple shear, performed at several orientations to the rolling direction and biaxial tension ii) air bending tests of rectangular samples after (or not) pre-straining in tension. The mechanical model is composed of the Yld2004-18p anisotropic yield criterion (Barlat et al. [3]) associated with a mixed hardening rule. The material parameters (altogether 21) are optimized with an inverse approach, in order to minimize the gap between experimental data and model predictions. Then, the Hosford-Coulomb rupture criterion is used in an uncoupled way, and the parameters are determined from tensile tests, both uniaxial and biaxial, with data up to rupture. In a second step, numerical simulations of the bending tests are performed, either on material in its original state or after pre-straining in tension, with pre-strain magnitudes increasing from 0.19 up to 0.3. The comparisons are performed on different outputs: load evolution, strain field and prediction of the rupture. A very good correlation is obtained over all the tests, in the identification step as well as in the validation one. Moreover, the fracture criterion proves to be successful whatever the amount of pre-strain may be. A convincing representation of the mechanical behavior at room temperature for an aluminium alloy is thus obtained.

Aluminium tolerance in bean traditional cultivars from Madeira

Common bean (Phaseolus vulgaris L.) is the most important legume crop in the world, providing low-cost, high quality protein, minerals and dietary fiber for human nutrition. The crop was originated from diversity centers in America and exhibits adaptation abilities to different environmental conditions, including soil with low pH. Acid soils occupy 30% of the agro ecosystem areas in the world. In Madeira, acid Andosols and unsatured Cambisols are the dominant groups of soils. Generally, under acidic and infertile conditions, besides of H+ toxicity, soluble aluminium (Al) is the most important abiotic factor limiting plant development and crop productivity. In the field, the hidden roots are also affected and the reduction of root growth under Al stress can be clearly observed in early stages. Seedlings of fifty bean accessions from the Archipelago of Madeira were tested under controlled conditions in the presence of 50 mM Al at pH 4.4. In general, the tested germplasm appeared to be sensitive or very sensitive to Al toxicity. However, fifteen traditional cultivars clearly exhibited elevated Al-tolerance, with an average root relative elongation (RRE) exceeding 50%, while top six accessions surpassed the 60% RRE mark. The Madeira bean germplasm is a valuable resource for sustainable crop production in acid soils and it could be used as parental lines in breeding programs aimed for Al tolerance in common beans.

Study on microwave dielectric properties of epoxy resin mixtures used for rapid product development

This paper presents a preliminary study on the dielectric properties and curing of three different types of epoxy resins mixed at various stichiometric mixture of hardener, flydust and aluminium powder under microwave energy. In this work, the curing process of thin layers of epoxy resins using microwave radiation was investigated as an alternative technique that can be implemented to develop a new rapid product development technique. In this study it was observed that the curing time and temperature were a function of the percentage of hardener and fillers presence in the epoxy resins. Initially dielectric properties of epoxy resins with hardener were measured which was directly correlated to the curing process in order to understand the properties of cured specimen. Tensile tests were conducted on the three different types of epoxy resins with hardener and fillers. Modifying dielectric properties of the mixtures a significant decrease in curing time was observed. In order to study the microstructural changes of cured specimen the morphology of the fracture surface was carried out by using scanning electron microscopy.

The role of HPC facilies in development of a novel road safety barrier

Water-filled portable road safety barriers are a common fixture in road works, however their use of water can be problematic, both in terms of the quantity of water used and the transportation of the water to the installation site. This project aims to develop a new design of portable road safety barrier, which will make novel use of composite and foam materials in order to reduce the barrier’s reliance on water in order to control errant vehicles. The project makes use of finite element (FE) techniques in order to simulate and evaluate design concepts. FE methods and models that have previously been tested and validated will be used in combination in order to provide the most accurate numerical simulations available to drive the project forward. LS-DYNA code is as highly dynamic, non-linear numerical solver which is commonly used in the automotive and road safety industries. Several complex materials and physical interactions are to be simulated throughout the course of the project including aluminium foams, composite laminates and water within the barrier during standardised impact tests. Techniques to be used include FE, smoothed particle hydrodynamics (SPH) and weighted multi-parameter optimisation techniques. A detailed optimisation of several design parameters with specific design goals will be performed with LS-DYNA and LS-OPT, which will require a large number of high accuracy simulations and advanced visualisation techniques. Supercomputing will play a central role in the project, enabling the numerous medium element count simulations necessary in order to determine the optimal design parameters of the barrier to be performed. Supercomputing will also allow the development of useful methods of visualisation results and the production of highly detailed simulations for end-product validation purposes. Efforts thus far have been towards integrating various numerical methods (including FEM, SPH and advanced materials models) together in an efficient and accurate manner. Various designs of joining mechanisms have been developed and are currently being developed into FE models and simulations.