Entwicklung, Aufbau und Messungen eines schnellen Eiskeimzählers

Im Rahmen dieser Arbeit wurde ein neuer Eiskeimzähler FINCH (Fast Ice Nucleus CHamber) entwickelt und erste Messungen von verschiedenen Testaerosolen im Labor und atmosphärischem Aerosol durchgeführt. Die Aerosolpartikel bzw. Ice Nuclei IN werden bei Temperaturen unter dem Gefrierpunkt und Übersättigungen in Bezug auf Eis zum Anwachsen zu Eiskristallen gebracht, um sie mittels optischer Detektion zu erfassen. In FINCH ist dies durch das Prinzip der Mischung realisiert, wodurch eine kontinuierliche Messung der IN-Anzahlkonzentration gewährleistet ist. Hierbei kann mit sehr hohen Sammelflussraten von bis zu 10 l/min gemessen werden. Ebenso ist ein schnelles Abfahren von verschiedenen Sättigungsverhältnissen in Bezug auf Eis in einem weiten Bereich von 0.9 - 1.7 bei konstanten Temperaturen bis zu −23 °C möglich. Die Detektion der Eiskristalle und damit der Bestimmung der IN-Anzahlkonzentration erfolgt über einen neu entwickelten optischen Sensor basierend auf der unterschiedlichen Depolarisation des zurückgestreuten Lichtes von Eiskristallen und unterkühlten Tropfen. In Labermessungen wurden Aktivierungstemperatur und -sättigungsverhältnis von Silberjodid AgI und Kaolinit vermessen. Die Resultate zeigten gute Übereinstimmungen mit Ergebnissen aus der Literatur sowie Parallelmessungen mit FRIDGE (FRankfurt Ice Deposition freezinG Experiment). FRIDGE ist eine statische Diffusionskammer zur Aktivierung und Auszählung von Eiskeimen, die auf einem Filter gesammelt wurden. Bei atmosphärischen Messungen auf dem Jungfraujoch(Schweiz) lagen die IN-Anzahlkonzentrationen mit bis zu 4 l−1 im Rahmen der aus der Literatur bekannten Werte. Messungen der Eiskristallresiduen von Mischwolken zeigten hingegen, dass nur jedes tausendste als Eiskeim im Depositionsmode aktiv ist. Hier scheinen andere Gefrierprozesse und sekundäre Eiskristallbildung von sehr großer Bedeutung für die Anzahlkonzentration der Eiskristallresiduen zu sein. Eine weitere Messung von atmosphärischem Aerosol in Frankfurt zeigte IN-Anzahlkonzentrationen bis zu 30 l−1 bei Aktivierungstemperaturen um −14 °C. Die parallele Probenahme auf Siliziumplättchen für die Messungen der IN-Anzahlkonzentration in FRIDGE ergaben Werte im gleichen Anzahlkonzentrationsbereich.

3D nanostructured microcarriers for cell therapy in regenerative medicine

Supercritical Emulsion Extraction technology (SEE-C) was proposed for the production of poly-lactic-co-glycolic acid microcarriers. SEE-C operating parameters as pressure, temperature and flow rate ratios were analyzed and the process performance was optimized in terms of size distribution and encapsulation efficiency. Microdevices loaded with bovine serum insulin were produced with different sizes (2 and 3 µm) or insulin charges (3 and 6 mg/g) and with an encapsulation efficiency of 60%. The microcarriers were characterized in terms of insulin release profile in two different media (PBS and DMEM) and the diffusion and degradation constants were also estimated by using a mathematical model. PLGA microdevices were also used in a cultivation of embryonic ventricular myoblasts (cell line H9c2 obtained from rat) in a FBS serum free medium to monitor cell viability and growth in dependence of insulin released. Good cell viability and growth were observed on 3 µm microdevices loaded with 3 mg/g of insulin. PLGA microspheres loaded with growth factors (GFs) were charged into alginate scaffold with human Mesenchimal Steam Cells (hMSC) for bone tissue engineering with the aim of monitoring the effect of the local release of these signals on cells differentiation. These “living” 3D scaffolds were incubated in a direct perfusion tubular bioreactor to enhance nutrient transport and exposing the cells to a given shear stress. Different GFs such as, h-VEGF, h-BMP2 and a mix of two (ratio 1:1) were loaded and alginate beads were recovered from dynamic (tubular perfusion system bioreactor) and static culture at different time points (1st, 7th, 21st days) for the analytical assays such as, live/dead; alkaline phosphatase; osteocalcin; osteopontin and Van Kossa Immunoassay. The immunoassay confirmed always a better cells differentiation in the bioreactor with respect to the static culture and revealed a great influence of the BMP-2 released in the scaffold on cell differentiation.

Regolazione della pompa elettrica del carburante a bassa pressione: Analisi dell'impatto sul consumo specifico di un motore a combustione interna

The trend of CO2 emission limit and fuel saving due to the oil price increase and are important drivers for engines development. The engine auxiliary devices electrification (g.e fuel pump) is a way to reduce the energy consumption, because it becomes possible to control them depending on engine operation point, this kid of management can be applied to the electric low-pressure pump. Usually the fuel delivery is performed at the maximum flow rate and a pressure regulator discharges the exceeding fuel amount inside the rail (gasoline engine) or upstream of the high pressure pump (common rail diesel engine). In this work it has been investigated the fuel saving achievable through a proper control of the electric fuel pump on a small common rail diesel engine, and a control architecture is proposed. The aim was to maximize the fuel economy without any impact on pressure control in the engine transient conditions. L'andamento del limite di emissioni di CO2 e il risparmio di carburante dovuto all'aumento del prezzo del petrolio sono fattori importanti per lo sviluppo dei motori. I dispositivi ausiliari, come la pompa del carburante, sono un modo per ridurre il consumo energetico, in quanto diventa possibile controllarli a seconda del punto di funzionamento del motore, questo tipo di gestione può essere applicato alla pompa elettrica a bassa pressione. Solitamente la portata del combustibile viene eseguita alla portata massima e un regolatore di pressione si scarica la quantità eccedente di carburante all'interno del rail (motore a benzina) o a monte della pompa a alta pressione (common rail motore diesel). In questo lavoro è stato studiato il risparmio di combustibile ottenibile attraverso un adeguato controllo della pompa elettrica del carburante su un piccolo motore diesel common rail e viene proposta una architettura di controllo. Lo scopo è quello di massimizzare il risparmio di carburante, senza alcun impatto sul controllo della pressione nelle condizioni transitorie del motore.

Analisi di fattibilità di un sensore di portata ad ultrasuoni

Analisi di possibile utilizzo di sensori ad ultrasuoni per il calcolo della portata massica. Tramite ricerche bibliografiche si è potuto osservare come sia stato possibile applicare tale strumento anche per il calcolo della velocità del vento in stazioni meteorologiche come anche per il calcolo della portata in condotti in cui scorrono liquidi o gas. Lo studio è stato realizzato in quanto la misura di portata interessa molti campi da quello aeronautico/automobilistico a quello industriale; un'applicazione aerospaziale, per esempio, può essere quella di calcolare la portata in ingresso ad una motorizzazione necessaria per quantificare le dosi di combustibile da iniettare in camera di combustione.

Konzept eines aktiven Pulverinhalators

In dieser Arbeit wird das Konzept eines aktiven Pulverinhalators entwickelt. Im Gegensatz zu einem passiven Pulverinhalator ist bei solch einem Gerät die Abgabe und Dispergierung der Arzneistoffformulierung nicht von einem Inhalationsmanöver abhängig, welches von Patient zu Patient variiert. Solch ein System würde folglich die Zuverlässigkeit und Effizienz der inhalativen Therapie verbessern. Mögliche Anwendungen für einen aktiven Pulverinhalator wären vor allem Indikationen, die die Abgabe hoher Dosen erfordern, wie z.B. in der Therapie mit Antibiotika.rnIn einem Designprozess, der alle aus Kundenwünschen ermittelten Konstruktionsanforderungen sammelt und verschiedene Lösungsansätze vergleicht, wird ein mit Treibgas betriebener atemzugsausgelöster, Mehrfach-Dosis Pulverinhalator als aussichtsreichstes Konzept ermittelt. Dieses Konzept wird in Form von eigens konstruierten Labor-Test-Rigs entwickelt und vor allem hinsichtlich Höhe der Dosierung, Dosiergenauigkeit, und Flussratenabhängigkeit evaluiert. In der Spitze können über 16 mg lungengängiger Dosis erreicht werden, bei im Vergleich zu dem eingesetzten passiven Inhalator mindestens nur halb so großer Streuung. Bei niedrigen Flussraten können immer noch bis zu 80 % der erzielten inhalierbaren Dosis von hohen Flussraten erreicht werden und damit die Ergebnisse des passiven Inhalators deutlich übertreffen.rnTeil der Aufgabe war es, dieses treibgasbetriebene Labor-Test-Rig so zu entwickeln, dass es implementierbar in einen atemzugsausgelösten Mehrfachdosis-Pulverinhalator ist. Dieser treibgasbetriebene, atemzugsausgelöste Mehrfachdosis-Pulverinhalator würde die Kundenwünsche und Konstruktionsanforderungen in sehr hohen Maße erfüllen, so dass hier die Möglichkeit besteht einen Inhalator mit sehr hohem Grad an Patienten-Compliance zu verwirklichen. Durch die Verwendung und Neukombination bereits etablierter Technologien und einen akzeptablen Stückkostenpreis besteht die Möglichkeit den Inhalator tatsächlich zu realisieren und zu vermarkten.

Effect of pulsatility on the mathematical modeling of rotary blood pumps

In this study, the effect of time derivatives of flow rate and rotational speed was investigated on the mathematical modeling of a rotary blood pump (RBP). The basic model estimates the pressure head of the pump as a dependent variable using measured flow and speed as predictive variables. Performance of the model was evaluated by adding time derivative terms for flow and speed. First, to create a realistic working condition, the Levitronix CentriMag RBP was implanted in a sheep. All parameters from the model were physically measured and digitally acquired over a wide range of conditions, including pulsatile speed. Second, a statistical analysis of the different variables (flow, speed, and their time derivatives) based on multiple regression analysis was performed to determine the significant variables for pressure head estimation. Finally, different mathematical models were used to show the effect of time derivative terms on the performance of the models. In order to evaluate how well the estimated pressure head using different models fits the measured pressure head, root mean square error and correlation coefficient were used. The results indicate that inclusion of time derivatives of flow and speed can improve model accuracy, but only minimally.

Morphological and functional 3-Tesla magnetic resonance imaging of saphenous vein coronary artery bypass grafts

Evaluation of a novel non-invasive tool for postoperative follow-up of patients postelective saphenous vein coronary artery bypass graft (CABG) was performed. Ten patients were included. Their bypass grafts supplied the right coronary artery (7), marginal branches (1), diagonal branches (2), and the circumflex artery (n=1). Each bypass was examined intraoperatively using Doppler flow measurement. Patients were examined with a 3-Tesla magnetic resonance imaging (MRI) scanner (MAGNETOM Verio, Siemens, Erlangen, Germany) within one week postsurgery using MR-angiography with an intravasal contrast agent and velocity encoded phase-contrast flow measurements. Intraoperative Doppler flow measurements revealed regular flow patterns in all vascular territories supplied. The median intraoperative flow rate was 50 ml/min with an inter-quartile range (IQR) of 42-70 ml/min. The clinical postoperative course was uneventful. MRI showed all grafts to be patent. The median postoperative flow rate was 50 ml/min (IQR: 32-65 ml/min). MRI flow rates agreed well with intraoperative Doppler flow measurements (mean difference: -2.8±20.1 ml/min). This initial study demonstrates that 3-Tesla MRI flow measurements correlated well with Doppler thus reconfirming the graft patency postCABG. Further refinement and broader application of this technique may facilitate follow-up postCABG potentially replacing empiric clinical judgment by reliable non-invasive imaging.

DESIGN OF A LIQUID FUEL INJECTOR FOR ALTERNATIVE FUEL STUDIES IN AN ATMOSPHERIC MODEL GAS TURBINE COMBUSTOR

A new liquid-fuel injector was designed for use in the atmospheric-pressure, model gas turbine combustor in Bucknell University’s Combustion Research Laboratory during alternative fuel testing. The current liquid-fuel injector requires a higher-than-desired pressure drop and volumetric flow rate to provide proper atomization of liquid fuels. An air-blast atomizer type of fuel injector was chosen and an experiment utilizing water as the working fluid was performed on a variable-geometry prototype. Visualization of the spray pattern was achieved through photography and the pressure drop was measured as a function of the required operating parameters. Experimental correlations were used to estimate droplet sizes over flow conditions similar to that which would be experienced in the actual combustor. The results of this experiment were used to select the desired geometric parameters for the proposed final injector design and a CAD model was generated. Eventually, the new injector will be fabricated and tested to provide final validation of the design prior to use in the combustion test apparatus.

Performance Characteristics of Airlift Pumps with Vortex Induced by Tangential Fluid Injection

The effect of the swirl component of air injection on the performance of an airlift pump was examined experimentally. An airlift pump is a device that pumps a liquid or slurry using only gas injection. In this study, the liquid used was water and the injected gas was air. The effect of the air swirl was determined by measuring the water discharge from an airlift pump with an air injection nozzle in which the air flow had both axial and tangential components and then repeating the tests with a nozzle with only axial injection. The induced water flow was measured using an orifice meter in the supply pipeline. Tests were run for air pressures ranging from 10 to 30 pounds per square inch, gauge (psig), at flow rates from 5 standard cubic feet per minute (scfm) up the maximum values attainable at the given pressure (usually in the range from 20 to 35 scfm). The nozzle with only axial injection produced a water flow rate that wasequivalent to or better than that induced by the nozzle with swirl. The swirl component of air injection was found to be detrimental to pump performance for all but the smallest air injection flow rate. Optimum efficiency was found for air injection pressures of 10 psig to 15 psig. In addition, the effect of using auxiliary tangential injection of water to create a swirl component in the riser before air injection on the overall capacity (i.e., flow rate) and efficiencyof the pump was examined. Auxiliary tangential water injection was found to have no beneficial effect on the pump capacity or performance in the present system.

Clinical Study Monitoring the pH on Tooth Surfaces in Patients with and without Erosion

The aim of this study was to compare tooth surface pH after drinking orange juice or water in 39 patients with dental erosion and in 17 controls. The following investigations were carried out: measurement of pH values on selected tooth surfaces after ingestion of orange juice followed by ingestion of water (acid clearance), measurement of salivary flow rate and buffering capacity. Compared with the controls, patients with erosion showed significantly greater decreases in pH after drinking orange juice, and the pH stayed lower for a longer period of time (p < 0.05). Saliva parameters showed no significant differences between the two patient groups except for a lower buffering capacity at pH 5.5 in the erosion group.

Microbiota in the oral subgingival biofilm is associated with obesity in adolescence

To test the hypothesis whether microbiota in oral biofilm is linked with obesity in adolescents we designed this cross-sectional study. Obese adolescents (n = 29) with a mean age of 14.7 years and normal weight subjects (n = 58) matched by age and gender were examined with respect to visible plaque index (VPI%) and gingival inflammation (bleeding on probing (BOP%)). Stimulated saliva was collected. They answered a questionnaire concerning medical history, medication, oral hygiene habits, smoking habits, and sociodemographic background. Microbiological samples taken from the gingival crevice was analyzed by checkerboard DNA-DNA hybridization technique. The sum of bacterial cells in subgingival biofilm was significantly associated with obesity (P < 0.001). The link between sum of bacterial cells and obesity was not confounded by any of the studied variables (chronic disease, medication, VPI%, BOP%, flow rate of whole saliva, or meal frequency). Totally 23 bacterial species were present in approximately threefold higher amounts, on average, in obese subjects compared with normal weight controls. Of the Proteobacteria phylum, Campylobacter rectus and Neisseria mucosa were present in sixfold higher amounts among obese subjects. The association between obesity and sum of bacterial cells in oral subgingival biofilm indicates a possible link between oral microbiota and obesity in adolescents.

Best combination of pre-stimulation and latency period duration before cluster attachment for efficient oxytocin release and milk ejection in cows with low to high udder-filling levels

Experiments were designed to investigate the suitability of a combination of a short manual teat stimulation with a short latency period before teat cup attachment to induce and maintain oxytocin release and milk ejection without interruption. In Experiment 1, seven dairy cows in mid lactation were manually pre-stimulated for 15, 30 or 45 s, followed by either 30 s or 45 s of latency period. It was shown that all treatments induced a similar release of oxytocin without interruption until the end of milking. In particular, the latency period of up to 45 s did not cause a transient decrease of oxytocin concentration. In Experiment 2, milking characteristics were recorded in seven cows each in early, mid, and late lactation, respectively. Because the course of milk ejection depends mainly on the degree of udder filling, individual milkings were classified based on the actual degree of udder filling which differs between lactational stages but also between morning and evening milkings. All animals underwent twelve different udder preparation treatments, i.e. 15, 30, or 45 s of pre-stimulation followed by latency periods of 0, 30, 45, or 60 s. Milking characteristics were recorded. Total milk yield, main milking time and average milk flow rate did not differ between treatments if the degree of udder filling at the start of milking was >40% of the maximum storage capacity. However, if the udder filling was <40%, main milking time was decreased with the duration of a latency period up to 45 s, independent of duration of pre-stimulation. Average milk flow at an udder filling of <40% was highest after a pre-stimulation of 45 s followed by a latency period of another 45 s. In contrast, average milk flow reached its lowest values at a pre-stimulation of 15 s without additional latency period. However, average milk flow after a 15-s pre-stimulation increased with increasing latency period. In conclusion, a very short pre-stimulation when followed by a latency period up to 45 s before teat cup attachment remains a suitable alternative for continuous stimulation to induce milk ejection.

Effect Of Confined Impinging Jet Mixing Processing Parameters On Poly (Lactic Acid) Nanoparticle Morphology

Biodegradable nanoparticles are at the forefront of drug delivery research as they provide numerous advantages over traditional drug delivery methods. An important factor affecting the ability of nanoparticles to circulate within the blood stream and interact with cells is their morphology. In this study a novel processing method, confined impinging jet mixing, was used to form poly (lactic acid) nanoparticles through a solvent-diffusion process with Pluronic F-127 being used as a stabilizing agent. This study focused on the effects of Reynolds number (flow rate), surfactant presence in mixing, and polymer concentration on the morphology of poly (lactic acid) nanoparticles. In addition to looking at the parameters affecting poly (lactic acid) morphology, this study attempted to improve nanoparticle isolation and purification methods to increase nanoparticle yield and ensure specific morphologies were not being excluded during isolation and purification. The isolation and purification methods used in this study were centrifugation and a stir cell. This study successfully produced particles having pyramidal and cubic morphologies. Despite successful production of these morphologies the yield of non-spherical particles was very low, additionally great variability existed between redundant trails. Surfactant was determined to be very important for the stabilization of nanoparticles in solution but appears to be unnecessary for the formation of nanoparticles. Isolation and purification methods that produce a high yield of surfactant free particles have still not been perfected and additional testing will be necessary for improvement.¿

Assessing the Validity of Brain Glucose Concentration Measurement Using Microdialysis

Brain functions, such as learning, orchestrating locomotion, memory recall, and processing information, all require glucose as a source of energy. During these functions, the glucose concentration decreases as the glucose is being consumed by brain cells. By measuring this drop in concentration, it is possible to determine which parts of the brain are used during specific functions and consequently, how much energy the brain requires to complete the function. One way to measure in vivo brain glucose levels is with a microdialysis probe. The drawback of this analytical procedure, as with many steadystate fluid flow systems, is that the probe fluid will not reach equilibrium with the brain fluid. Therefore, brain concentration is inferred by taking samples at multiple inlet glucose concentrations and finding a point of convergence. The goal of this thesis is to create a three-dimensional, time-dependent, finite element representation of the brainprobe system in COMSOL 4.2 that describes the diffusion and convection of glucose. Once validated with experimental results, this model can then be used to test parameters that experiments cannot access. When simulations were run using published values for physical constants (i.e. diffusivities, density and viscosity), the resulting glucose model concentrations were within the error of the experimental data. This verifies that the model is an accurate representation of the physical system. In addition to accurately describing the experimental brain-probe system, the model I created is able to show the validity of zero-net-flux for a given experiment. A useful discovery is that the slope of the zero-net-flux line is dependent on perfusate flow rate and diffusion coefficients, but it is independent of brain glucose concentrations. The model was simplified with the realization that the perfusate is at thermal equilibrium with the brain throughout the active region of the probe. This allowed for the assumption that all model parameters are temperature independent. The time to steady-state for the probe is approximately one minute. However, the signal degrades in the exit tubing due to Taylor dispersion, on the order of two minutes for two meters of tubing. Given an analytical instrument requiring a five μL aliquot, the smallest brain process measurable for this system is 13 minutes.

The Investigation of Uniform, Monodisperse Crystalline Particles via the Evaporation of Small Droplets

Many industrial solids processes require the production of disperse particles. In industries such as food, personal care, and pharmaceuticals, particle formation is widely used to produce solid products or to separate substances in intermediate process steps. The most important characteristics known to impact the effectiveness of a solid product are purity, size, internal structure, and morphology. These characteristics are essential to maintain optimal operation of subsequent process steps and for obtaining the desired high quality product. This thesis aims to aid in the advancement of particle production technology by (1) investigating the use of a vibrating orifice aerosol generator (VOAG) for collecting data to predict particle attributes including morphology, size, and internal structure as a function of processing parameters such as solvent, solution concentration, air flow rate, and initial droplet size, as well as to (2) determine the extent to which uniform droplet evaporation can be a tool to achieve novel particle morphologies, controlled sizes, or internal structures (crystallinity and crystal form). Experimental results for succinic acid, L-serine, and L-glutamic acid suggest that particles of controlled characteristics can indeed be produced by this method. Analysis by scanning electron microscopy (SEM), nanoindentation, and X-ray diffraction (XRD) shows that various sizes, internal structures, and morphologies can be obtained using the VOAG. Furthermore, unique morphologies and unexpected internal structures were able to be achieved for succinic acid, providing an added benefit to particle formation by this method.