A moored underwater energy conservation system for profiling measurement

There is a need to obtain the hydrologic data including ocean current, wave, temperature and so on in the South China Sea. A new profiling instrument which does not suffer from the damage due to nature forces or incidents caused by passing ships, is under development to acquire data from this area. This device is based on a taut single point mid-water mooring system. It incorporates a small, instrumented vertically profiling float attached via an electromechanical cable to a winch integral with the main subsurface flotation. On a pre-set schedule, the instrument float with sensors is winched up to the surface if there is no strip passing by, which is defined by an on-board miniature sonar. And it can be immediately winched down to a certain depth if the sonar sensor finds something is coming. Since, because Of logistics, the area can only be visited once for a long time and a minimum of 10 times per day profiles are desired, energy demands are severe. To respond to these concerns, the system has been designed to conserve a substantial portion of the potential energy lost during the ascent phase of each profile and subsequently use this energy to pull the instrument down. Compared with the previous single-point layered measuring mode, it is advanced and economical. At last the paper introduces the test in the South China Sea.

Validation of RADARSAT-2 fully polarimetric SAR measurements of ocean surface waves

C band RADARSAT-2 fully polarimetric (fine quad-polarization mode, HH+VV+HV+VH) synthetic aperture radar (SAR) images are used to validate ocean surface waves measurements using the polarimetric SAR wave retrieval algorithm, without estimating the complex hydrodynamic modulation transfer function, even under large radar incidence angles. The linearly polarized radar backscatter cross sections (RBCS) are first calculated with the copolarization (HH, VV) and cross-polarization (HV, VH) RBCS and the polarization orientation angle. Subsequently, in the azimuth direction, the vertically and linearly polarized RBCS are used to measure the wave slopes. In the range direction, we combine horizontally and vertically polarized RBCS to estimate wave slopes. Taken together, wave slope spectra can be derived using estimated wave slopes in azimuth and range directions. Wave parameters extracted from the resultant wave slope spectra are validated with colocated National Data Buoy Center (NDBC) buoy measurements (wave periods, wavelengths, wave directions, and significant wave heights) and are shown to be in good agreement.

Generation of internal and surface waves by seafloor movement in a two layer fluid system

Internal and surface waves generated by the deformations of the solid bed in a two layer fluid system of infinite lateral extent and uniform depth are investigated. An integral solution is developed for an arbitrary bed displacement on the basis of a linear approximation of the complete description of wave motion using a transform method (Laplace in time and Fourier in space) analogous to that used to study the generation of tsunamis by many researchers. The theoretical solutions are presented for three interesting specific deformations of the seafloor; the spatial variation of each seafloor displacement consists of a block section of the seafloor moving vertically either up or down while the time-displacement history of the block section is varied. The generation process and the profiles of the internal and surface waves for the case of the exponential bed movement are numerically illustrated, and the effects of the deformation parameters, densities and depths of the two layers on the solutions are discussed. As expected, the solutions derived from the present work include as special cases that obtained by Kervella et al. [Theor Comput Fluid Dyn 21:245-269, 2007] for tsunamis cased by an instantaneous seabed deformation and those presented by Hammack [J Fluid Mech 60:769-799, 1973] for the exponential and the half-sine bed displacements when the density of the upper fluid is taken as zero.

Measurements of ocean wave and current field using dual polarized X-band radar

A new ocean wave and sea surface current monitoring system with horizontally-(HH) and vertically-(VV) polarized X-band radar was developed. Two experiments into the use of the radar system were carried out at two sites, respectively, for calibration process in Zhangzi Island of the Yellow Sea, and for validation in the Yellow Sea and South China Sea. Ocean wave parameters and sea surface current velocities were retrieved from the dual polarized radar image sequences based on an inverse method. The results obtained from dual-polarized radar data sets acquired in Zhangzi Island are compared with those from an ocean directional buoy. The results show that ocean wave parameters and sea surface current velocities retrieved from radar image sets are in a good agreement with those observed by the buoy. In particular, it has been found that the vertically-polarized radar is better than the horizontally-polarized radar in retrieving ocean wave parameters, especially in detecting the significant wave height below 1.0 m.

Vertical structure and evolution of the Luzon Warm Eddy

Eddies are frequently observed in the northeastern South China Sea (SCS). However, there have been few studies on vertical structure and temporal-spatial evolution of these eddies. We analyzed the seasonal Luzon Warm Eddy (LWE) based on Argo float data and the merged data products of satellite altimeters of Topex/Poseidon, Jason-1 and European Research Satellites. The analysis shows that the LWE extends vertically to more than 500 m water depth, with a higher temperature anomaly of 5A degrees C and lower salinity anomaly of 0.5 near the thermocline. The current speeds of the LWE are stronger in its uppermost 200 m, with a maximum speed of 0.6 m/s. Sometimes the LWE incorporates mixed waters from the Kuroshio Current and the SCS, and thus has higher thermohaline characteristics than local marine waters. Time series of eddy kinematic parameters show that the radii and shape of the LWE vary during propagation, and its eddy kinetic energy follows a normal distribution. In addition, we used the empirical orthogonal function (EOF) here to analyze seasonal characteristics of the LWE. The results suggest that the LWE generally forms in July, intensifies in August and September, separates from the coast of Luzon in October and propagates westward, and weakens in December and disappears in February. The LWE's westward migration is approximately along 19A degrees N latitude from northwest of Luzon to southeast of Hainan, with a mean speed of 6.6 cm/s.

Onshore-offshore variations of copepod community in northern South China Sea

Copepod communities in onshore and offshore waters show a gradient from primarily near shore to primarily oceanic species. Understanding the transition between these communities is fundamental to determining the range of coastal influence. Copepod communities in the northern South China Sea (nSCS) were studied based on samples collected by vertically towing a net in 10 February-6 March (winter) and 26 August-6 September (summer) of 2004. Calanoida species richness, total copepod abundance, Shannon-Weaver diversity index, and onshore-offshore occurrence of dominant species showed obvious change from onshore to offshore waters. Although the offshore stations had lower abundance than the shelf stations, they had more species and larger diversity index. Abundance of some species (groups) with dominance index > 5% (Calanus sinicus, Euchaeta spp., Temora spp., Paracalanus parvus, and Subeucalanus subtenuis) declined from onshore to offshore waters. Warm water species (Pleuromamma abdominalis, P. gracilis, and P. robusta) occurred in offshore waters in both cruises. Station (q-type) cluster analysis in winter and summer separated copepod community into onshore and offshore communities at similar to 40% level of similarity. The two communities were divided at the position of similar to 100-m isobath. In summer, C. sinicus occurred in the upwelling area east of Hainan Island, indicating the presence of an oversummering stock of this species.

Wintertime meso-scale horizontal distribution of large tintinnids in the southern Yellow Sea

Spatial distribution of some large tintinnid species (nominally > 76 mu m) is investigated on samples vertically towed in the southern Yellow Sea in winters of 2001 to 2004. Nine tintinnid species are recorded: Codonellopsis morchella, Stenosemella pacifica, S. steini, Tintinnopsis schotti, T. radix, T. karajacensis, Eutintinnus tenuis, Parafavella sp., Leprotintinnus neriticus, of which C. morchella and T. radix dominated in the warm tongue-shaped zone of the Yellow Sea Warm Current (YSWC), and S. pacifica is the next in abundance. Our study shows that these tintinnids occur repeatedly in certain special distribution patterns.

Distribution pattern of marine flagellate and its controlling factors in the central and north part of the Huanghai Sea in early summer

A survey was carried out in the central and north part of the Huanghai Sea (34.5degrees similar to 37.0degreesN, 120.5degrees similar to124.0degreesE) during June 12 similar to 27, 2000. It was found that the abundance of marine flagellate ranged from 45 to 1278 cell/ml, 479 cell/ml in average. Flagellate was more abundant in the central part than in the north part of Huanghai Sea, and the abundance decreased with the increasing distance from the coast, showing a similar distribution pattern with isotherm. Vertically, high density of flagellate was always presented in the bottom of thermocline, and formed a dense accumulation in the central area of the Huanghai Sea Cold Water Mass. The effects of physical and biological factors on the distribution of marine flagellate in early summer were discussed. Water temperature (especially the existence of thermocline) rather than salinity showed significant effect on the distribution pattern of marine flagellate in the Huanghai Sea in early summer. When comparing the abundance of marine flagellate with that of other microorganisms, it revealed a comparatively stable relationship among these organhisms, with a ratio of heterotrophic bacteria: cyanobacteria: flagellate: dinoflagellate: ciliate being 10(5) 10(3):10(2):10(1):10(0).

Control mechanisms of diel vertical migration: Theoretical assumptions

We explore control mechanisms underlying the vertical migration of zooplankton in the water column under the predator-avoidance hypothesis. Two groups of assumptions in which the organisms are assumed to migrate vertically in order to minimize realized or effective predation pressure (type-I) and to minimize changes in realized or effective predation pressure (type-II), respectively, are investigated. Realized predation pressure is defined as the product of light intensity and relative predation abundance and the part of realized predation pressure that really affects organisms is termed as effective predation pressure. Although both types of assumptions can lead to the migration of zooplankton to avoid the mortality from predators, only the mechanisms based on type-II assumptions permit zooplankton to undergo a normal diel vertical migration (morning descent and evening ascent). The assumption of minimizing changes in realized predation pressure is based on consideration of DVM induction only by light intensity and predators. The assumption of minimizing changes in effective predation pressure takes into account, apart from light and predators also the effects of food and temperature. The latter assumption results in the same expression of migration velocity as the former one when both food and temperature are constant over water depth. A significant characteristic of the two type-II assumptions is that the relative change in light intensity plays a primary role in determining the migration velocity. The photoresponse is modified by other environmental variables: predation pressure, food and temperature. Both light and predation pressure are necessary for organisms to undertake DVM. We analyse the effect of each single variable. The modification of the phototaxis of migratory organisms depends on the vertical distribution of these variables. (C) 2001 Academic Press.

Observation and modeling for terrestrial processes in alpine meadow

The water-heat transfer process between land and atmosphere in Haibei alpine meadow area has been systematically observed. A multi-layer coupling model for land-atmosphere interaction was presented with special attention paid to the moisture transfer in leaf stomata under unsaturated condition. A profound investigation on the physical process of turbulent transfer inside the vegetation has been performed with a revised formula of water absorption for root system. The present model facilitates the study of vertically distributed physical variables in detail. Numerical simulation was conducted according to the transfer process of Kinesia humility meadow in the area of Haibei Alpine Meadow Ecosystem Station, CAS. The calculated results agree well with observation.

一种测量深海应答器坐标的方法

提出一种适用于深海应答器坐标测量的方法:垂线相交法。这种方法利用立体几何原理,获得应答器坐标。即测量母船在距应答器适中的位置沿两条相互垂直的航迹航行,分别找到两条航迹上与应答器斜距最小的点,过这两个点在水平面上做两条垂线,交点的经纬度坐标就是应答器的经纬度坐标。分析了影响测量误差的重要因素,并提出测量原则以满足精度要求,使测量系统具有很好的鲁棒性。为提高测距精度,采用射线声学理论中的RRA算法对声线进行修正。仿真实验证明了垂线相交法的有效性。该测量方法对深度没有要求,简化了繁琐的现场操作和水声测量系统,具有很高的工程实用价值。

VTI各向异性叠前深度偏移及速度分析

Theoretical research, laboratory test and field observation show that most of sediment rock has anisotropic features. It will produce some notable errors when applying isotropic methods such as prestack depth migration and velocity analysis to dada acquired under anisotropic condition; it also has a bad effect on geologic interpretation. Generally speaking, the vertical transverse isotropic media is a good approximation to geologic structure, thus it has an important realistic meaning for anisotropic prestack depth migration theory researching and precise complex geologic imaging if considering anisotropic effect of seismic wave propagation. There are two indispensable parts in prestack depth migration of realistic records, one is proper prestack depth migration algorithm, and the other is velocity analysis using prestack seismic data. The paper consists of the two aspects. Based on implicit finite difference research proposed by Dietrich Ristow et al （1997） about VTI media prestack depth migration, the paper proposed split-step Fourier prestack depth migration algorithm （VTISSF） and Fourier finite difference algorithm （VTIFFD） based on wave equation for VTI media, program are designed and the depth migration method are tested using synthetic model. The result shows that VTISSF is a stable algorithm, it generally gets a good result if the reflector dip is not very steep, while undermigration phenomena appeared in steep dips case; the VTIFFD algorithm bring us better result in steep dips with lower efficiency and frequency dispersion. For anisotropic prestack depth migration velocity analysis of VTI media, The paper discussed the basic hypothesis of VTI model in velocity analysis algorithm, basis of anisotropic prestack depth migration velocity analysis and travel time table calculation of VTI media in integral prestack depth migration. Then , analyzed the P-wave common imaging gather in the case of homogeneous velocity and vertically variable velocity . studied the residual correction in common imaging gather produced by media parameter error, analyzed the condition of flat event and correct depth in common imaging gather . In this case, the anisotropic model parameter vector is , is vertical velocity of a point at top surface, is vertical velocity gradient, and are anisotropic parameter. We can get vertical velocity gradient from seismic data; then the P-wave common imaging gather of VTI media whose velocity varies in vertical and horizontal direction, the relationship between media parameter and event residual time shift of common image gather are studied. We got the condition of flattening common imaging gather with correct depth. In this case the anisotropic model parameter vector is , is velocity gradient in horizontal direction. As a result, the vertical velocity grads can be decided uniquely, but horizontal velocity grads and anisotropic parameter can’t be distinguished if no priori information available, our method is to supply parameter by velocity scanning; then, as soon as is supplied we can get another four parameters of VTI media from seismic data. Based on above analysis, the paper discussed the feasibility of migration velocity analysis in vertically and horizontally varied VTI media, synthetic record of three models are used to test the velocity analysis method . Firstly, anisotropic velocity analysis test is done using a simple model with one block, then we used a model with multiple blocks, thirdly, we analyzed the anisotropic velocity using a part of Marmousi model. The model results show that this velocity analysis method is feasible and correct.

高邮凹陷陈堡及陈堡东地区油气成藏规律研究

With the development of petroleum exploration in Gaoyou Depression, both old and new areas have been the active exploration targets, so the study of petroleum accumulation is significant to the petroleum exploration in the study area and the integrated oil and gas accumulation theory. Based on hydrocarbon accumulation theory and systematical research methods and combined with the structural characteristics of Gaoyou Depression, Chenbao and East of Chenbao were selected as the study areas in this dissertation, oil and gas migration pathways, accumulation periods, as well as accumulation models were studied, and favorable exploration targets were proposed. There develop three sets source rocks, which are Tai-2 Member, Fu-2 Member and Fu-4 Member respectively. Tai-2 Member is the predominant source rock in the eastern part. Fu-2 Member mainly occurs in the northern slope, while Fu-4 Member develops in the deep depression. In the study area, oil mainly comes from Fu-2 Member of Liuwushe subsag. The lower limit of TOC is 0.4%, and active source rock mostly distributed in the south fault-step zone. The source rock in Liuwushe subsag began to generate hydrocarbon in the late of Dainan depositional stage and the threshold was 2300m. The macro and micro characteristics of reservoirs and the reservoir heterogeneity characteristics of the Fu-1 Member were studied systematicly. The results show that Fu-1 Member, which has better reservoir properties, are medium porosity-medium permeability reservoir. The reservoir permeability has good correlation with porosity connectivity. The reservoirs have strong dissolution, pores are mainly thin to medium throat, and throat radii are distributed concentratedly, the sorting is good and pore structures are homogeneous. Sandstone reservoirs whether in the plan view, interlayer or in layers have a certain degree of heterogeneity, in particular, the heterogeneity in layers directly affect and control the oil and gas migration and accumulation. By analyzing the lithology correlation of the fault walls, shale smear, cross section stress, the configuration of fracture active periods and hydrocarbon generation and expulsion periods and fuzzy comprehensive evaluation, the main faults sealing were evaluated. The results show that the faults in Chenbao and East of Chenbao had poor sealing properties in Sanduo period and could be used as the migration pathways at that time. After Sanduo period, the tectonic stress fields in the area changed largely, and, consequently, the fault properties converted from tensional shear to compressive shear, the faults changed progressively from close to open, so the faults sealing became better and were conducive to the preservation of oil and gas reservoirs. According to the seismic event suspension modes and profile configurations above and under the unconformities, combined with tectonic evolutions of the study areas, the unconformity types can be classified into truncation unconformity, overlapped unconformity and parallel unconformity and the distribution characteristics of unconformities in the plan view was also studied. The unconformity structure was divided into basal conglomerate, weathered clay and semi-weathered layer vertically in the study area and this kind of structure make unconformities to be effective oil and gas migration pathways and is significant to hydrocarbon accumulation in a parts of areas. With the analyses of typical oil and gas reservoirs in the study area, combined with the research results of pathway systems, hydrocarbon accumulation models were established and the oil and gas accumulation laws in Chenbao and East of Chenbao analyzed. The oil and gas came from Liuwushe subsag and Liuliushe subsag. The oil and gas from Liuwushe subsag mainly migrated from the structural high parts into the fault-step zone along strata in northeast direction, a part of them migrated upward into the fault-step zone and the Wubao low uplift along Wu-1 Fault in northeast direction. The oil and gas from Liuliushe subsag mainly migrated into the upper reservoirs through Wu-2 fault, and lesser oil and gas migrated into the fault-step zone because of the controls of cross-section orientation, depression center and the hydrocarbon formation tendency. The favorable exploration targets in Chenbao and East of Chenbao have been concluded: the southern fault-step zone is a favorable oil and gas accumulation zone of Liuwushe subsag, and they are fault block reservoirs where fault acted as the barriers, the main target intervals are Fu-1 Member and Fu-3 Member in palaeocene; Oil and gas in the middle and northern fault-step zone mainly laterally migrated from the south areas, and the main target interval is Fu-3 Member in palaeocene; Fu-1 Member and the reserviors above the Wubao subsag are still the focuses in future explorations. The results of this study have important guiding significance for the future oil and gas exploration.

元谋盆地河湖相沉积记录的上新世印度季风转型事件

The Indian monsoon, an integral part of the global climate system, has been extensively investigated during the past decades. Most of the proxy records are derived from marine sediments and focused on time periods of the late Miocene and Pleistocene. The Pliocene represents a period when Earth’s boundary conditions underwent dramatic changes. However, variations of the Indian monsoon during the Pliocene and its forcing mechanisms have remained unclear. The Yuanmou Basin, located in the region of the Indian monsoon, provides an ideal target for understanding the Pliocene history of Indian monsoon variations. Detailed investigations on the lithostratigraphy, magnetostratigraphy and limnology of a 650-m-thick fluvio-lacustrine sedimentary sequence from the basin are carried out in the present study. The clay and clay-plus-fine-silt fractions of the sediments are referred to the midlake-facies components, and changes in the percentages of both fractions generally reflect changes in the water level of the lakes developed in the basin closely related to variations in the intensity of the Indian monsoon. Whereas the greenish-gray lacustrine mud beds represent the environment of deep-water lakes, and the frequency of individual lacustrine mud beds is considered to indicate the frequency of the deep-water lakes developed in the basin associated with the variability of the Indian monsoon. The proxy data suggest that the Indian monsoon experienced abrupt shifts at 3.53, 3.14, 2.78 and 2.42 Ma, respectivey. 1) Since 3.53 Ma, the midlake-facies components displayed a general trend of increase in the concentrations, accompanied by an increase in the sedimentation rate from an average ~10 to 25 cm ka–1. The data suggest that high stands of the lakes in the basin rose progressively, implying a gradual intensification of the Indian monsoon since that time. This shift occurred coeval with the accelerated uplift of the northern Tibetan Plateau, denoting a close link between the Indian monsoon strengthening and the Tibetan Plateau uplifting. 2) 2.78 Ma ago, the concentrations of the midlake-facies components decreased abruptly and the dominant fraction of the sediments turned to fluvial sands. The data indicate that lakes in the basin disappeared, reflecting a dramatic decline in the intensity of the Indian monsoon at that time. This shift coincided with the formation of extensive Northern Hemisphere ice sheets, implying a quick response of the low-latitude monsoon regime to the high-latitude glaciation. 3) At 3.14 Ma, the initial appearance of blackish-grey mud beds with long durations and occasional occurrences of lacustrine mud beds indicate that the basin was overall dominated by shallow lakes, implying a shift to decreased variability of the Indian monsoon at that time. At 2.42 Ma, an increase in the frequency and a decrease in the duration of the lacustrine mud beds suggest that deep-water lakes were frequently developed in the basin, denoting a shift to increased variability of the Indian monsoon at that time. The former shift coincides with the onset of large-scale glaciation in the circum Atlantic region and the latter corresponds to the inception of predominance of the 41 ka periodicity in Northern Hemisphere ice-sheet cover fluctuations, presumably suggesting a physical link between the Indian monsoon system and the high-latitude ice sheets in the Northern Hemisphere.

湖南、广西泥盆纪硅岩地球化学与沉积构造背景

During the Devonian, a complicated carbonate platform-basin configuration was created through transtensional rifting in the context of opening of Devonian South China Sea; extensive bedded chert, commonly interbedded with tuffaceous beds, occurred in the narrow, elongate interplatform basins (or troughs) in South China, where they occurred earlier (Early Devonian) in southern Guangxi and later (early Late Devonian) in northern Guangxi-south central Hunan. In order to unravel the origin and distribution of the bedded chert successions, and their relationships to basement faulting activities during the opening of the Devonian South China Sea, studies of element (major, minor and REE) geochemistry and Rb-Sr, Sm-Nd isotopic systematics are carried out upon the chert deposits. These chert deposits commonly have high SiO2 contents and (average 94.01%) and low TFe2O3 (average 0.55%), together with other geochemical parameters, suggestive of both biogenic and hydrothermal origins. However, Fe/Ti ratio are high along the elongate interplatform basins(troughs) to the northwest along Wuxiangling-Zhaisha-Chengbu, and to the southeast along Xiaodong-Mugui-Xinpu, suggesting relatively intense hydrothermal activities there. They generally contain very low total REE contents (∑REE average 31.21ug/g) with mediate negative Ce anomalies (mean Ce/Ce*=0.83) and low Lan/Cen values (average 1.64), indicating an overall continental margin basin where they precipitated. The northward increases in Ce/Ce* values, particularly along the elongate troughs bounded both to the east and west of the Guangxi-Huanan rift basin, suggest a northward enhancement of terrigenous influences, thereby reflecting a gradual northward propagation of open marine setting. Generally low positive Eu anomalies in the chert, except for the apparently high Eu anomalies in the chert from Chengbu (Eu/Eu* up to 4.6), suggest mild hydrothermal venting activities in general, except for those at Chengbu. The initial 87Sr/86Sr (0) ratios of chert generally vary from 0.712000 to 0.73000 , suggesting influences both from terrigenous influx and seawater. The Nd isotopic model ages (tDM or t2DM) and initial εNd (0) values of chert vary mostly from 1.5 to 2.1 Ga, and from –16 to –21, respectively, implying that the silica sources were derived from the provenances of the Palaeoproterozoic crust relics at depth. The high εNd (0) values of chert (-0.22 to 14.7) in some localities, mostly along the elongate troughs, suggest that silica sources may have been derived from deeper-seated mantle, being channeled through the interplate boundary fault zones extending downwards to the mantle. At Wuxiangling, Nanning, chert occurs extensively from the Emsian through the Frasnian strata, both U/Th ratios and tDM ages of chert reached up to a maximum in the early Frasnian corresponding to the extensive development of chert in South China, pointing to a maximum extensional stage of Devonian South China basin, which is supported by the Ce/Ce* values as is opposed to the previous datasets as the coeval minimum values.