Electrical Evaluation of a Low Concentrating PVT Collector Based on Performance Ratio

Photovoltaic Thermal/Hybrid collectors are an emerging technology that combines PV and solar thermal collectors by producing heat and electricity simultaneously. In this paper, the electrical performance evaluation of a low concentrating PVT collector was done through two testing parts: power comparison and performance ratio testing. For the performance ratio testing, it is required to identify and measure the factors affecting the performance ratio on a low concentrating PVT collector. Factors such as PV cell configuration, collector acceptance angle, flow rate, tracking the sun, temperature dependence and diffuse to irradiance ratio. Solarus low concentrating PVT collector V12 was tested at Dalarna University in Sweden using the electrical equipment at the solar laboratory. The PV testing has showed differences between the two receivers. Back2 was producing 1.8 energy output more than Back1 throughout the day. Front1 and Front2 were almost the same output performance. Performance tests showed that the cell configuration for Receiver2 with cells grouping (6- 32-32-6) has proved to have a better performance ratio when to it comes to minimizing the shading effect leading to more output power throughout the day because of lowering the mismatch losses. Different factors were measured and presented in this thesis in chapter 5. With the current design, it has been obtained a peak power at STC of 107W per receiver. The solar cells have an electrical efficiency of approximately 19% while the maximum measured electrical efficiency for the collector was approximately 18 % per active cell area, in addition to a temperature coefficient of -0.53%/ ˚C. Finally a recommendation was done to help Solarus AB to know how much the electrical performance is affected during variable ambient condition and be able to use the results for analyzing and introducing new modification if needed.

Ionic liquids in electrochemical devices and processes : managing interfacial electrochemistry

Many ionic liquids offer a range of properties that make them attractive to the field of electrochemistry; indeed it was electrochemical research and applications that ushered in the modern era of interest in ionic liquids. In parallel with this, a variety of electrochemical devices including solar cells, high energy density batteries, fuel cells, and supercapacitors have become of intense interest as part of various proposed solutions to improve sustainability of energy supply in our societies. Much of our work over the last ten years has been motivated by such applications. Here we summarize the role of ionic liquids in these devices and the insights that the research provides for the broader field of interest of these fascinating liquids.

Nanoelectrodes : energy conversion and storage

Nanosized materials are known to take on peculiar properties compared to the bulk material. Their electronic and mechanical properties are known to improve e.g. higher electrical conductivity and greater strength. Their electrochemical redox properties can change dramatically, e.g. in the case of Ag°, the E° value for Ag° → Ag+ + e can change by up to half a volt as the particle size decreases. Nanodimensional materials also have an extraordinarily high surface area to volume ratio. All of these properties would bring beneficial effects if they could be retained when the material is assembled into a structure capable of being used as an electrode – nanostructured electrodes.

Here we consider selected examples illustrating the importance of nanostructured electrodes in energy conversion (organic solar cells and fuel cells) and storage (batteries and capacitors). These examples involve the use of inorganic as well as organic conducting and semiconducting materials.

New approach to controllable nitrogen doping for improved nano-semiconductors

The data covers the following:
X-ray photoelectron spectroscopy (XPS) - to collect surface chemical structure changes (using RMIT instrument);
Scanning electron microscopy (SEM) - to collect surface physical structure changes;
Atomic force microscopy (AFM) - to collect surface morphology changes;
Internal/External quantum efficiency (IQE/EQE) – to collect DSSC (Dye Sensitised Solar Cells) efficiency data;
Discharge/Charge capacity - to collect battery efficiency data.

Ionic liquids and organic ionic plastic crystals utilizing small phosphonium cations

The development of new liquid and solid state electrolytes is paramount for the advancement of electrochemical devices such as lithium batteries and solar cells. Ionic liquids have shown great promise in both these applications. Here we demonstrate the use of phosphonium cations with small alkyl chain substituents, in combination with a range of different anions, to produce a variety of new halide free ionic liquids that are fluid, conductive and with sufficient thermal stability for a range of electrochemical applications. Walden plot analysis of the new phosphonium ionic liquids shows that these can be classed as "good" ionic liquids, with low degrees of ion pairing and/or aggregation, and the lithium deposition and stripping from one of these ionic liquids has been demonstrated. Furthermore, for the first time phosphonium cations have been used to form a range of organic ionic plastic crystals. These materials can show significant ionic conductivity in the solid state and thus are of great interest as potential solid-state electrolyte materials.

Incorporation of fused tetrathiafulvalenes (TTFs) into polythiophene architectures : varying the electroactive dominance of the TTF species in hybrid systems

A novel polythienylenevinylene (PTV) and two new polythiophenes (PTs), featuring fused tetrathiafulvalene (TTF) units, have been prepared and characterized by ultraviolet−visible (UV−vis) and electron paramagnetic resonance (EPR) spectroelectrochemistry. All polymers undergo two sequential, reversible oxidation processes in solution. Structures in which the TTF species is directly linked to the polymer backbone (2 and 4) display redox behavior which is dictated by the fulvalene system. Once the TTF is spatially removed from the polymer chain by a nonconjugated link (polymer 3), the electroactivity of both TTF and polythiophene moieties can be detected. Computational studies confirm the delocalization of charge over both electroactive centers (TTF and PT) and the existence of a triplet dication intermediate. PTV 4 has a low band gap (1.44 eV), is soluble in common organic solvents, and is stable under ambient conditions. Organic solar cells of polymer 4:[6,6]-phenyl-C₆₁ butyric acid methyl ester (PCBM) have been fabricated. Under illumination, a photovoltaic effect is observed with a power conversion efficiency of 0.13% under AM1.5 solar simulated light. The onset of photocurrent at 850 nm is consistent with the onset of the π−π absorption band of the polymer. Remarkably, UV−vis spectroelectrochemistry of polymer 4 reveals that the conjugated polymer chain remains unchanged during the oxidation of the polymer.

Recent progress in the development and use of organic ionic plastic crystal electrolytes

Significant progress has been made recently in the development of Organic Ionic Plastic Crystals (OIPCs), a unique family of solid state electrolytes with applications in electrochemical devices such as lithium batteries and dye-sensitised solar cells. The negligible volatility of OIPCs renders them more suitable than molecular species for long-term device use, while the high thermal and electrochemical stability of many OIPCs fulfils an essential requirement for solid state electrolytes for many device applications. However, the complex mechanisms of conduction through these materials, both in their pure state and in the presence of a small amount of a second component (such as lithium salts to enable their use in lithium batteries) are still not fully understood. At the same time, the range of anions and cations utilised in the synthesis of plastic crystal phases continues to increase. This perspective concentrates on recent research into both fundamental and device-oriented aspects of these materials. Important fundamental understanding of the physical properties and transport mechanisms of different OIPCs has been achieved through use of techniques including variable temperature solid-state NMR and crystallographic analysis, as well as detailed molecular dynamics simulations. In parallel, the applicability of these materials as electrolytes for dye-sensitised solar cells and lithium batteries is being more widely demonstrated. The possibility of using OIPCs as solid state electrolytes for fuel cells is also discussed.

An organic ionic plastic crystal electrolyte for rate capability and stability of ambient temperature lithium batteries

Reliable, safe and high performance solid electrolytes are a critical step in the advancement of high energy density secondary batteries. In the present work we demonstrate a novel solid electrolyte based on the organic ionic plastic crystal (OIPC) triisobutyl(methyl)phosphonium bis(fluorosulfonyl)imide (P1444FSI). With the addition of 4 mol% LiFSI, the OIPC shows a high conductivity of 0.26 mS cm-1 at 22 °C. The ion transport mechanisms have been rationalized by compiling thermal phase behaviour and crystal structure information obtained by variable temperature synchrotron X-ray diffraction. With a large electrochemical window (ca. 6 V) and importantly, the formation of a stable and highly conductive solid electrolyte interphase (SEI), we were able to cycle lithium cells (LiLiFePO4) at 30 °C and 20 °C at rates of up to 1 C with good capacity retention. At the 0.1 C rate, about 160 mA h g-1 discharge capacity was achieved at 20 °C, which is the highest for OIPC based cells to date. It is anticipated that these small phosphonium cation and [FSI] anion based OIPCs will show increasing significance in the field of solid electrolytes.

Design and fabrication of nano-sinusoid LSPR devices

Applications of LSPR nano-particles in various areas of solar cells, LSPR biosensors, and SERS biosensors, based on interaction of light with noble metal nano-particles is increasing. Therefore, design and nano-fabrication of the LSPR devices is a key step in developing such applications. Design of nano-structures with desirable spectral properties using numerical techniques such as finite difference time domain (FDTD) is the first step in this work. A new structure called nano-sinusoid, satisfying the some desirable LSPR characteristics, is designed and simulated using the FDTD method. In the next stage, analytical method of electro static eigen mode method is used to validate the simulation results. The, nano-fabrications method of electron beam lithography (EBL) is implemented to fabricate the proposed profile with high precision. Finally, atomic force microscopy (AFM) is used to investigate the shape of the fabricated nano-particles, and the dark field microscopy is employed to demonstrate the particular spectral characteristics of the proposed nano-sinusoids.

Aggregation of a dibenzo[b,def]chrysene based organic photovoltaic material in solution

Detailed electrochemical studies have been undertaken on molecular aggregation of the organic semiconductor 7,14-bis((triisopropylsilyl)-ethynyl) dibenzo[b,def]chrysene (TIPS-DBC), which is used as an electron donor material in organic solar cells. Intermolecular association of neutral TIPS-DBC molecules was established by using 1H NMR spectroscopy as well as by the pronounced dependence of the color of TIPS-DBC solutions on concentration. Diffusion limited current data provided by near steady-state voltammetry also reveal aggregation. Furthermore, variation of concentration produces large changes in shapes of transient DC and Fourier transformed AC (FTAC) voltammograms for oxidation of TIPS-DBC in dichloromethane. Subtle effects of molecular aggregation on the reduction of TIPS-DBC are also revealed by the highly sensitive FTAC voltammetric method. Simulations of FTAC voltammetric data provide estimates of the kinetic and thermodynamic parameters associated with oxidation and reduction of TIPS-DBC. Significantly, aggregation of TIPS-DBC facilitates both one-electron oxidation and reduction by shifting the reversible potentials to less and more positive values, respectively. EPR spectroscopy is used to establish the identity of one-electron oxidized and reduced forms of TIPS-DBC. Implications of molecular aggregation on the HOMO energy level in solution are considered with respect to efficiency of organic photovoltaic devices utilizing TIPS-DBC as an electron donor material. © 2014 American Chemical Society.

Ionic liquids for energy, materials, and medicine.

As highlighted by the recent ChemComm web themed issue on ionic liquids, this field continues to develop beyond the concept of interesting new solvents for application in the greening of the chemical industry. Here some current research trends in the field will be discussed which show that ionic liquids research is still aimed squarely at solving major societal issues by taking advantage of new fundamental understanding of the nature of these salts in their low temperature liquid state. This article discusses current research trends in applications of ionic liquids to energy, materials, and medicines to provide some insight into the directions, motivations, challenges, and successes being achieved with ionic liquids today.

Recent developments in electrospinning of nanofiber yarns

Nanofibers possess high surface area and excellent porosity. Though nanofibers can be produced by a variety of techniques, electrospinning stands distinct because of its simplicity and flexibility in processing different polymer materials, and ability to control fiber diameter, morphology, orientation, and chemical component. Nonetheless, electrospun nanofibers are predominantly produced in the form of randomly oriented fiber webs, which restrict their wide use. Converting nanofibers into twisted continuous bundles, i.e., nanofiber yarns, can improve their strength and facilitate their subsequent processes, but remains challenging to make. Nanofiber yarns also create enormous opportunities to develop well-defined three-dimensional nanofibrous architectures. This review article gives an overview of the state-of-the-art techniques for electrospinning of nanofiber yarns and control of nanofiber alignment. A detailed account on techniques to produce twisted/non-twisted short bundles and continuous yarns are discussed.

Electrochemistry of tris(2,2′-bipyridyl) cobalt(II) in ionic liquids and aprotic molecular solvents on glassy carbon and platinum electrodes

The tris(2,2′-bipyridyl) complexes of cobalt(II) and (III) ([Co(bpy)3]^2+/3+) produce a redox couple of great interest in thermoelectrochemical cells and dye sensitized solar cells including both types of devices based on ionic liquid electrolytes. We present a systematic study of the electrochemistry of [Co(bpy)3]²⁺ [NTf2]^-2 in two ionic liquids (ILs) based on the 1-ethyl-3-methylimidazolium (C2mim) cation and two ILs based on the 1-butyl-1-methylpyrrolidinium cation (C4mpyr), as well as three aprotic molecular solvents. Platinum (Pt) and glassy carbon (GC) working electrodes were compared. In all solvents better electrochemical responses were observed on GC, which yielded higher currents in the cyclic voltammograms and lower rate constants for the redox reaction. The [Co(bpy)3]^1+/2+ couple is also readily observed, but this redox reaction is chemically irreversible, possibly because the [Co(bpy)3]¹⁺ complex dissociates. However, the [Co(bpy)3]^1+/2+ reaction is chemically reversible in all of the solvents studied, except 3-methoxypropionitrile, if excess of 2,2′-bipyridyl is added to the solution.

Construção de células solares de corantes fotoexcitáveis utilizando flavonóides da capsicum frutescens, pimenta malagueta

The conversion of solar energy in electric with photo-voltaic cells has been carried through exclusively with devices of semiconducting junction. To put this situation comes moving for better in them last years, thanks to a new technology of production of known solar cells as Dye Solar Cell. This proposal aims at to develop a DSC having as dye lavonoides of the Capsicum frutescens (malagueta pepper). Front is considered to evaluate the photo-voltaic parameters varies it regions of the visible specter, as well as a good efficiency of conversion