The utilization bound of non-preemptive rate-monotonic scheduling in controller area networks is 25%

Consider a distributed computer system comprising many computer nodes, each interconnected with a controller area network (CAN) bus. We prove that if priorities to message streams are assigned using rate-monotonic (RM) and if the requested capacity of the CAN bus does not exceed 25% then all deadlines are met.

Analyzing TDMA with slot skipping

Distributed real-time systems, such as factory automation systems, require that computer nodes communicate with a known and low bound on the communication delay. This can be achieved with traditional time division multiple access (TDMA). But improved flexibility and simpler upgrades are possible through the use of TDMA with slot-skipping (TDMA/SS), meaning that a slot is skipped whenever it is not used and consequently the slot after the skipped slot starts earlier. We propose a schedulability analysis for TDMA/SS. We assume knowledge of all message streams in the system, and that each node schedules messages in its output queue according to deadline monotonic. Firstly, we present a non-exact (but fast) analysis and then, at the cost of computation time, we also present an algorithm that computes exact queuing times.

Current mortars in conservation: an overview

Renders are an important item in historical buildings and the need for their periodical re-application is a basic conservation procedure. In modern times there has been a trend towards the replacement of traditional pure lime mortars by new formulations including Portland cement or hydraulic lime. Apart from those interventions on specific and very important monuments, in which the use oftraditional non-hydraulic mortars can be enforced, in most of the projects involving less than first order magnitude heritage the use of some sort of hydraulic components is becoming the rule rather than the exception. The present paper describes and analyses the results of an experimental study with ten formulations of current mortars - including some that can hardly be considered as adequate conservation procedures - allowing a direct comparison in terms of some of the most relevant characteristics.

Non invasive ventilation during exercise in COPD patients: a systematic review with meta-analysis

COPD is a major cause of morbidity and mortality worldwide, representing a major public health problem due to the high health and economic resource consumption. Pulmonary rehabilitation is a standard care recommendation for these patients, in order to control the symptoms and optimize the functional capacity, reducing health care costs associated with exacerbations and activity limitations and participation. However, in patients with severe COPD exercise performance can be difficult, due to extreme dyspnea, decreased muscle strength and fatigue. In addition, hypoxemia and dyspnea during efforts and daily activities may occur, limiting their quality of life. Thus, NIV have been used as adjunct to exercise, in order to improve exercise capacity in these patients. However, there is no consensus for this technique recommendation. Our objective was to verify whether the use of NIV during exercise is effective than exercise without NIV in dyspnea, walked distance, blood gases and health status in COPD patients, through a systematic review and meta-analysis.

Non-adherence to telemedicine interventions for drug users: systematic review

OBJECTIVE To estimate rates of non-adherence to telemedicine strategies aimed at treating drug addiction. METHODS A systematic review was conducted of randomized controlled trials investigating different telemedicine treatment methods for drug addiction. The following databases were consulted between May 18, 2012 and June 21, 2012: PubMed, PsycINFO, SciELO, Wiley (The Cochrane Library), Embase, Clinical trials and Google Scholar. The Grading of Recommendations Assessment, Development and Evaluation was used to evaluate the quality of the studies. The criteria evaluated were: appropriate sequence of data generation, allocation concealment, blinding, description of losses and exclusions and analysis by intention to treat. There were 274 studies selected, of which 20 were analyzed. RESULTS Non-adherence rates varied between 15.0% and 70.0%. The interventions evaluated were of at least three months duration and, although they all used telemedicine as support, treatment methods differed. Regarding the quality of the studies, the values also varied from very poor to high quality. High quality studies showed better adherence rates, as did those using more than one technique of intervention and a limited treatment time. Mono-user studies showed better adherence rates than poly-user studies. CONCLUSIONS Rates of non-adherence to treatment involving telemedicine on the part of users of psycho-active substances differed considerably, depending on the country, the intervention method, follow-up time and substances used. Using more than one technique of intervention, short duration of treatment and the type of substance used by patients appear to facilitate adherence.

Direct search optimization application programming interface with remote access

Search Optimization methods are needed to solve optimization problems where the objective function and/or constraints functions might be non differentiable, non convex or might not be possible to determine its analytical expressions either due to its complexity or its cost (monetary, computational, time,...). Many optimization problems in engineering and other fields have these characteristics, because functions values can result from experimental or simulation processes, can be modelled by functions with complex expressions or by noise functions and it is impossible or very difficult to calculate their derivatives. Direct Search Optimization methods only use function values and do not need any derivatives or approximations of them. In this work we present a Java API that including several methods and algorithms, that do not use derivatives, to solve constrained and unconstrained optimization problems. Traditional API access, by installing it on the developer and/or user computer, and remote API access to it, using Web Services, are also presented. Remote access to the API has the advantage of always allow the access to the latest version of the API. For users that simply want to have a tool to solve Nonlinear Optimization Problems and do not want to integrate these methods in applications, also two applications were developed. One is a standalone Java application and the other a Web-based application, both using the developed API.

ENCOURAGE architecture: support for heterogeneous smart grids

Our society relies on energy for most of its activities. One application domain inciding heavily on the energy budget regards the energy consumption in residential and non-residential buildings. The ever increasing needs for energy, resulting from the industrialization of developing countries and from the limited scalability of the traditional technologies for energy production, raises both problems and opportunities. The problems are related to the devastating effects of the greenhouse gases produced by the burning of oil and gas for energy production, and from the dependence of whole countries on companies providing gas and oil. The opportunities are mostly technological, since novel markets are opening for both energy production via renewable sources, and for innovations that can rationalize energy usage. An enticing research effort can be the mixing of these two aspects, by leveraging on ICT technologies to rationalize energy production, acquisition, and consumption. The ENCOURAGE project aims to develop embedded intelligence and integration technologies that will directly optimize energy use in buildings and enable active participation in the future smart grid environment.The primary application domains targeted by the ENCOURAGE project are non-residential buildings (e.g.: campuses) and residential buildings (e.g.: neighborhoods). The goal of the project is to achieve 20% of energy savings through the improved interoperability between various types of energy generation, consumption and storage devices; interbuilding energy exchange; and systematic performance monitoring.

Visualizing non-linear control system performance by means of multidimensional scaling

This paper addresses the use of multidimensional scaling in the evaluation of controller performance. Several nonlinear systems are analyzed based on the closed loop time response under the action of a reference step input signal. Three alternative performance indices, based on the time response, Fourier analysis, and mutual information, are tested. The numerical experiments demonstrate the feasibility of the proposed methodology and motivate its extension for other performance measures and new classes of nonlinearities.

Non-uniform microstrip antenna array for RX DSRC communications

The urgent need to mitigate traffic problems such as accidents, road hazards, pollution and traffic jam have strongly driven the development of vehicular communications. DSRC (Dedicated Short Range Communications) is the technology of choice in vehicular communications, enabling real time information exchange among vehicles V2V (Vehicle-to-Vehicle) and between vehicles and infrastructure V2I (Vehicle-Infrastructure). This paper presents a receiving antenna for a single lane DSRC control unit. The antenna is a non-uniform array with five microstrip patches. The obtained beam width, bandwidth and circular polarization quality, among other characteristics, are compatible with the DSRC standards, making this antenna suitable for this application. © 2014 IEEE.

The impact of different power dividers used in a non-uniform planar antenna array

Wireless communications are widely used for various applications, requiring antennas with different features. Often, to achieve the desired radiation pattern, is necessary to employ antenna arrays, using non-uniform excitation on its elements. Power dividers can be used and the best known are the T-junction and the Wilkinson power divider, whose main advantage is the isolation between output ports. In this paper the impact of this isolation on the overall performance of a circularly polarized planar antenna array using non-uniform excitation is investigated. Results show a huge decrease of the array bandwidths either in terms of return loss or in polarization, without resistors. © 2014 IEEE.

A shared-disk parallel cluster file system

Dissertação apresentada para obtenção do Grau de Doutor em Informática Pela Universidade Nova de Lisboa, Faculdade de Ciências e Tecnologia

Política(s) de saúde no trabalho : um inquérito sociológico às empresas portuguesas

Resumo Política(s) de saúde no trabalho: um inquérito sociológico às empresas portuguesas A literatura portuguesa sobre políticas, programas e actividades de Segurança, Higiene e Saúde no Trabalho (abreviadamente, SH&ST) é ainda escassa. Com este projecto de investigação pretende-se (i) colmatar essa lacuna, (ii) melhorar o conhecimento dos sistemas de gestão da saúde e segurança no trabalho e (iii) contribuir para a protecção e a promoção da saúde dos trabalhadores. Foi construída uma tipologia com cinco grupos principais de políticas, programas e actividades: A (Higiene & Segurança no Trabalho / Melhoria do ambiente físico de trabalho); B (Avaliação de saúde / Vigilância médica / Prestação de cuidados de saúde); C (Prevenção de comportamentos de risco/ Promoção de estilos de vida saudáveis); D (Intervenções a nível organizacional / Melhoria do ambiente psicossocial de trabalho); E (Actividades e programas sociais e de bem-estar). Havia uma lista de mais de 60 actividades possíveis, correspondendo a um índice de realização de 100%. Foi concebido e desenhado, para ser auto-administrado, um questionário sobre Política de Saúde no Local de Trabalho. Foram efectuados dois mailings, e um follow-up telefónico. O trabalho de campo decorreu entre a primavera de 1997 e o verão de 1998. A amostra (n=259) é considerada representativa das duas mil maiores empresas do país. Uma em cada quatro é uma multinacional. A taxa de sindicalização rondava os 30% da população trabalhadora, mas apenas 16% dos respondentes assinalou a existência de representantes dos trabalhadores eleitos para a SH&ST. A hipótese de investigação principal era a de que as empresas com um sistema integrado de gestão da SH&ST seriam também as empresas com um (i) maior número de políticas, programas e actividades de saúde; (ii) maior índice de saúde; (iii) maior índice de realização; e (iv) maior percentagem dos encargos com a SH&ST no total da massa salarial. As actividades de tipo A e B, tradicionalmente associadas à SH&ST, representavam, só por si, mais de 57% do total. Os resultados, correspondentes às respostas da Secção C do questionário, apontam, para (i) a hipervalorização dos exames de medicina do trabalho; e por outro para (ii) o subaproveitamento de um vasto conjunto de actividades (nomeadamente as de tipo D e E), que são correntemente levadas a cabo pelas empresas e que nunca ou raramente são pensadas em termos de protecção e promoção da saúde dos trabalhadores. As actividades e os programas de tipo C (Prevenção de comportamentos de risco/Promoção de estilos de vida saudáveis), ainda eram as menos frequentes entre nós, a seguir aos Programas sociais e de bem-estar (E). É a existência de sistemas de gestão integrados de SH&ST, e não o tamanho da empresa ou outra característica sociodemográfica ou técnico-organizacional, que permite predizer a frequência de políticas de saúde mais activas e mais inovadores. Os três principais motivos ou razões que levam as empresas portuguesas a investir na protecção e promoção da saúde dos seus trabalhadores eram, por ordem de frequência, (i) o absentismo em geral; (ii) a produtividade, qualidade e/ou competitividade, e (iii) a filosofia de gestão ou cultura organizacional. Quanto aos três principais benefícios que são reportados, surge em primeiro lugar (i) a melhoria da saúde dos trabalhadores, seguida da (ii) melhoria do ambiente do ambiente de trabalho e, por fim, (iii) a melhoria da produtividade, qualidade e/ou competitividade.Quanto aos três principais obstáculos que se põem, em geral, ao desenvolvimento das iniciativas de saúde, eles seriam os seguintes, na percepção dos respondentes: (i) a falta de empenho dos trabalhadores; (ii) a falta de tempo; e (iii) os problemas de articulação/ comunicação a nível interno. Por fim, (i) o empenho das estruturas hierárquicas; (ii) a cultura organizacional propícia; e (iii) o sentido de responsabilidade social surgem, destacadamente, como os três principais factores facilitadores do desenvolvimento da política de saúde no trabalho. Tantos estes factores como os obstáculos são de natureza endógena, susceptíveis portanto de controlo por parte dos gestores. Na sua generalidade, os resultados deste trabalho põem em evidência a fraqueza teóricometodológica de grande parte das iniciativas de saúde, realizadas na década de 1990. Muitas delas seriam medidas avulsas, que se inserem na gestão corrente das nossas empresas, e que dificilmente poderão ser tomadas como expressão de uma política de saúde no local de trabalho, (i) definida e assumida pela gestão de topo, (ii) socialmente concertada, (iii) coerente, (iv) baseada na avaliação de necessidades e expectativas de saúde dos trabalhadores, (v) divulgada, conhecida e partilhada por todos, (vi) contingencial, flexível e integrada, e, por fim, (vii) orientada por custos e resultados. Segundo a Declaração do Luxemburgo (1997), a promoção da saúde engloba o esforço conjunto dos empregadores, dos trabalhadores, do Estado e da sociedade civil para melhorar a segurança, a saúde e o bem-estar no trabalho, objectivo isso que pode ser conseguido através da (i) melhoria da organização e das demais condições de trabalho, da (ii) participação efectiva e concreta dos trabalhadores bem como do seu (iii) desenvolvimento pessoal. Abstract Health at work policies: a sociological inquiry into Portuguese corporations Portuguese literature on workplace health policies, programs and activities is still scarce. With this research project the author intends (i) to improve knowledge on the Occupational Health and Safety (shortly thereafter, OSH) management systems and (ii) contribute to the development of health promotion initiatives at a corporate level. Five categories of workplace health initiatives have been identified: (i) Occupational Hygiene and Safety / Improvement of Physical Working Environment (type A programs); (ii) Health Screening, Medical Surveillance and Other Occupational Health Care Provision (type B programs); (iii) Preventing Risk Behaviours / Promoting Healthy Life Styles (type C programs); (iv) Organisational Change / Improvement of Psycho-Social Working Environment (type D programs); and (v) Industrial and Social Welfare (type E programs). A mail questionnaire was sent to the Chief Executive Officer of the 1500 largest Portuguese companies, operating in the primary and secondary sectors (≥ 100 employees) or tertiary sector (≥ 75 employees). Response rate has reached about 20% (259 respondents, representing about 300 companies). Carried out between Spring 1997 and Summer 1998, the fieldwork has encompassed two direct mailings and one phone follow-up. Sample is considered to be representative of the two thousand largest companies. One in four is a multinational. Union membership rate is about 30%, but only 16% has reported the existence of a workers’ health and safety representative. The most frequent workplace health initiatives were those under the traditional scope of the OSH field (type A and B programs) (57% of total) (e.g., Periodical Medical Examinations; Individual Protective Equipment; Assessment of Working Ability). In SMEs (< 250) it was less likely to find out some time-consuming and expensive activities (e.g., Training on OSH knowledge and skills, Improvement of environmental parameters as ventilation, lighting, heating).There were significant differences in SMEs, when compared with the larger ones (≥ 250) concerning type B programs such as Periodical medical examinations, GP consultation, Nursing care, Other medical and non-medical specialities (e.g., psychiatrist, psychologist, ergonomist, physiotherapist, occupational social worker). With regard to type C programs, there were a greater percentage of programs centred on Substance abuse (tobacco, alcohol, and drug) than on Other health risk behaviours. SMEs representatives reported very few prevention- oriented programs in the field of Drug abuse, Nutrition, Physical activity, Off- job accidents, Blood pressure or Weight control. Frequency of type D programs included Training on Human Resources Management, Training on Organisational Behaviour, Total Quality Management, Job Design/Ergonomics, and Workplace rehabilitation. In general, implementation of this type of programs (Organisational Change / Improvement of Psychosocial Working Environment) is not largely driven by health considerations. Concerning Industrial and Social Welfare (Type E programs), the larger employers are in a better position than SMEs to offer to their employees a large spectrum of health resources and facilities (e.g., Restaurant, Canteen, Resting room, Transport, Infra-structures for physical activity, Surgery, Complementary social protection, Support to recreational and cultural activities, Magazine or newsletter, Intranet). Other workplace health promotion programs like Training on Stress Management, Employee Assistance Programs, or Self-help groups are uncommon in the Portuguese worksites. The existence of integrated OSH management systems, not the company size, is the main variable explaining the implementation of more active and innovative workplace health policies in Portugal. The three main prompting factors reported by employers for health protection and promotion initiatives are: (i) Employee absenteeism; (ii) Productivity, quality and/or competitiveness; and (iii) Corporate culture/management philosophy. On the other hand, (i) Improved staff’s health, (ii) Improved working environment and (iii) Improved productivity, quality and/or competitiveness were the three main benefits reported by companies’ representatives, as a result of successful implementation of workplace health initiatives. (i) Lack of staff commitment; (ii) Lack of time; and (iii) Problems of co-operation and communication within company or establishment (iii) are perceived to be the main barriers companies must cope with. Asked about the main facilitating factors, these companies have pointed out the following ones: (i) Top management commitment; (ii) Corporate culture; and (iii) Sense of social responsibility. This sociological research report shows the methodological weaknesses of workplace health initiatives, carried out by Portuguese companies during the last ‘90s. In many cases, these programs and actions were not part of a corporate health strategy and policy, (i) based on the assessment of workers’ health needs and expectancies, (ii) advocated by the employer or the chief executive officer, (ii) planned and implemented with the staff consultation and participation or (iv) evaluated according to a cost-benefit analysis. In short, corporate health policy and action were still rather based on more traditional OSH approaches and should be reoriented towards Workplace Health Promotion (WHP) approach. According to the Luxembourg Declaration of Workplace Health Promotion in the European Union (1997), WHP is “a combination of: (i) improving the work organisation and environment; (ii) promoting active participation; (iii) encouraging personal development”.Résumée Politique(s) de santé au travail: une enquête sociologique aux entreprises portugaises Au Portugal on ne sait presque rien des politiques de santé au travail, adoptés par les entreprises. Avec ce projet de recherche, on veut (i) améliorer la connaissance sur les systèmes de gestion de la santé et de la sécurité au travail et, au même temps, (ii) contribuer au développement de la promotion de la santé des travailleurs. Une typologie a été usée pour identifier les politiques, programmes et actions de santé au travail: A. Amélioration des conditions de travail / Sécurité au travail; B. Médecine du travail /Santé au travail; C. Prévention des comportements de risque / Promotion de styles de vie sains; D. Interventions organisationnelles / Amélioration des facteurs psychosociaux au travail; E. Gestion de personnel et bien-être social. Un questionnaire postal a été envoyé au représentant maximum des grandes entreprises portugaises, industrielles (≥ 100 employés) ou des services (≥ 75 employés). Le taux de réponse a été environ 20% (259 répondants, concernant trois centaines d’entreprises et d’établissements). La recherche de champ, conduite du printemps 1997 à l’été 1998, a compris deux enquêtes postales et un follow-up téléphonique. L´échantillon est représentatif de la population des deux miles plus grandes entreprises. Un quart sont des multinationales. Le taux de syndicalisation est d’environ 30%. Toutefois, il y a seulement 16% de lieux de travail avec des représentants du personnel pour la santé et sécurité au travail. Les initiatives de santé au travail les plus communes sont celles concernant le domaine plus traditionnel (types A et B) (57% du total): par exemple, les examens de médecine du travail, l’équipement de protection individuelle, les tests d’aptitude au travail. En ce qui concerne les programmes de type C, les plus fréquents sont le contrôle et la prévention des addictions (tabac, alcool, drogue). Les interventions dans le domaine de du système technique et organisationnelle du travail peuvent comprendre les courses de formation en gestion de ressources humaines ou en psychosociologie des organisations, l’ergonomie, le travail posté ou la gestion de la qualité totale. En général, la protection et la promotion de la santé des travailleurs ne sont pas prises en considération dans l’implémentation des initiatives de type D. Il y a des différences quand on compare les grandes entreprises et les moyennes en matière de politique de gestion du personnel e du bien-être (programmes de type E, y compris l’allocation de ressources humaines ou logistiques comme, par exemple, restaurant, journal d’entreprise, transports, installations et équipements sportifs). D’autres activités de promotion de la santé au travail comme la formation en gestion du stress, les programmes d’ assistance aux employés, ou les groupes de soutien et d’auto-aide sont encore très peu fréquents dans les entreprises portugaises. C’est le système intégré de gestion de la santé et de la sécurité au travail, et non pas la taille de l’entreprise, qui aide à prédire l’existence de politiques actives et innovatrices dans ce domaine. Les trois facteurs principaux qui encouragent les actions de santé (prompting factors, en anglais) sont (i) l’absentéisme (y compris la maladie), (ii) les problèmes liés à la productivité, qualité et/ou la compétitivité, et aussi (iii) la culture de l’entreprise/philosophie de gestion. Du coté des bénéfices, on a obtenu surtout l’amélioration (i) de la santé du personnel, (ii) des conditions de travail, et (iii) de la productivité, qualité et/ou compétitivité.Les facteurs qui facilitent les actions de santé au travail sont (i) l’engagement de la direction, (ii) la culture de l’entreprise, et (iii) le sens de responsabilité sociale. Par contre, les obstacles à surmonter, selon les organisations qui ont répondu au questionnaire, seraient surtout (i) le manque d’engagement des travailleurs et de leur représentants, (ii) le temps insuffisant, et (iii) les problèmes de articulation/communication au niveau interne de l’entreprise/établissement. Ce travail de recherche sociologique montre la faiblesse méthodologique des services et activités de santé et sécurité au travail, mis en place par les entreprises portugaises dans les années de 1990, à la suite des accords de concertation sociale de 1991. Dans beaucoup de cas, (i) ces politiques de santé ne font pas partie encore d’un système intégré de gestion, (ii) il n’a pas d’évaluation des besoins et des expectatives des travailleurs, (iii) c’est très bas ou inexistant le niveau de participation du personnel, (iv) on ne fait pas d’analyse coût-bénéfice. On peut conclure que les politiques de santé au travail sont plus proches de la médecine du travail et de la sécurité au travail que de la promotion de la santé des travailleurs. Selon la Déclaration du Luxembourg sur la Promotion de la Santé au Lieu de Travail dans la Communauté Européenne (1997), celle-ci « comprend toutes les mesures des employeurs, des employés et de la société pour améliorer l'état de santé et le bien être des travailleurs » e « ceci peut être obtenu par la concentration des efforts dans les domaines suivants: (i) amélioration de l'organisation du travail et des conditions de travail ; (ii) promotion d'une participation active des collaborateurs ; (iii) renforcement des compétences personnelles ».

Evidence for non-coaxiality of ferrimagnetic and paramagnetic fabrics, developed during magma flow and cooling in a thick mafic dyke

A detailed analysis of fabrics of the chilled margin of a thick dolerite dyke (Foum Zguid dyke, Southern Morocco) was performed in order to better understand the development of sub-fabrics during dyke emplacement and cooling. AMS data were complemented with measurements of paramagnetic and ferrimagnetic fabrics (measured with high field torque magnetometer), neutron texture and microstructural analyses. The ferrimagnetic and AMS fabrics are similar, indicating that the ferrimagnetic minerals dominate the AMS signal. The paramagnetic fabric is different from the previous ones. Based on the crystallization timing of the different mineralogical phases, the paramagnetic fabric appears related to the upward flow, while the ferrimagnetic fabric rather reflects the late-stage of dyke emplacement and cooling stresses. (C) 2014 Elsevier B.V. All rights reserved.

Effect of hole drilling at the overlap on the strength of single-lap joints

Bonded unions are gaining importance in many fields of manufacturing owing to a significant number of advantages to the traditional fastening, riveting, bolting and welding techniques. Between the available bonding configurations, the single-lap joint is the most commonly used and studied by the scientific community due to its simplicity, although it endures significant bending due to the non-collinear load path, which negatively affects its load bearing capabilities. The use of material or geometric changes in single-lap joints is widely documented in the literature to reduce this handicap, acting by reduction of peel and shear peak stresses at the damage initiation sites in structures or alterations of the failure mechanism emerging from local modifications. In this work, the effect of hole drilling at the overlap on the strength of single-lap joints was analyzed experimentally with two main purposes: (1) to check whether or not the anchorage effect of the adhesive within the holes is more preponderant than the stress concentrations near the holes, arising from the sharp edges, and modification of the joints straining behaviour (strength improvement or reduction, respectively) and (2) picturing a real scenario on which the components to be bonded are modified by some external factor (e.g. retrofitting of decaying/old-fashioned fastened unions). Tests were made with two adhesives (a brittle and a ductile one) varying the adherend thickness and the number, layout and diameter of the holes. Experimental testing showed that the joints strength never increases from the un-modified condition, showing a varying degree of weakening, depending on the selected adhesive and hole drilling configuration.

Wrong sign and symmetric limits and non-decoupling in 2HDMs

We analyse the possibility that, in two Higgs doublet models, one or more of the Higgs couplings to fermions or to gauge bosons change sign, relative to the respective Higgs Standard Model couplings. Possible sign changes in the coupling of a neutral scalar to charged ones are also discussed. These wrong signs can have important physical consequences, manifesting themselves in Higgs production via gluon fusion or Higgs decay into two gluons or into two photons. We consider all possible wrong sign scenarios, and also the symmetric limit, in all possible Yukawa implementations of the two Higgs doublet model, in two different possibilities: the observed Higgs boson is the lightest CP-even scalar, or the heaviest one. We also analyse thoroughly the impact of the currently available LHC data on such scenarios. With all 8 TeV data analysed, all wrong sign scenarios are allowed in all Yukawa types, even at the 1 sigma level. However, we will show that B-physics constraints are crucial in excluding the possibility of wrong sign scenarios in the case where tan beta is below 1. We will also discuss the future prospects for probing the wrong sign scenarios at the next LHC run. Finally we will present a scenario where the alignment limit could be excluded due to non-decoupling in the case where the heavy CP-even Higgs is the one discovered at the LHC.