Effect of soaking and cooking on phytate concentration, minerals, and texture of food-type soybeans

The increasing consumption of soybeans due to its bioactive compounds has attracted interest in describing the grain's constituents and variation during processing. Phytate has been the aim of much research since it chelates essential minerals but also has beneficial antioxidant effects. This study evaluated the variation of phytate, calcium, zinc, and iron during soaking and cooking of soybeans. The phytate: Zn and phytate: Fe molar ratios were determined in order to estimate the bioavailability of these minerals. Six food-type varieties were used: BR 36, BRS 213, BRS 216, BRS 232, BRS 155, and Embrapa 48. The samples were soaked in water 3:1 (w/w) for 12 hours at room temperature and cooked. Cooking time was determined by modeling the softening of each variety using fractional conversion. Water content, phytate, and minerals were determined in raw, soaked and cooked samples. The water content of raw grains for all varieties was 9.9 g.100 g-1 increasing to a range of 58.1-63.7 g.100 g-1 after soaking and 63.1-66.0 g.100 g-1 after cooking. Soaking caused a significant reduction in phytate (23-30%), but cooking caused no additional reduction. The phytate: Zn molar ratio was 20 indicating that zinc absorption could be impaired, while the phytate: Fe molar ratio was 8, below the level of compromising absorption

Quality of Canned mandarin as affected by preservation liquid

This study is integrated within a research line dedicated to evaluate different options to introduce mandarin in Spanish agro-food industries and in both national and international markets. The effects of different preservation liquids (sucrose solution, sucrose and ascorbic acid solution, grape, and grapefruit juices), soluble solids (10, 12, 14 ºBrix), and thermal processing (30 seconds at 98 ºC) on vitamin C, color, carotenoids and sensory quality of canned Satsuma mandarin segments were studied. The liquid preservation that presented the best results was grapefruit juice, which provided the highest vitamin C (323 mg.L-1) and total carotenoids (16.4 mg.L-1) contents (the main carotenoid found was β-cryptoxanthin), intense orange color, high thermal stability, and very good sensory quality (e.g. intense floral and fresh-mandarin aromas and low levels of off-flavors).

Influence of temperature on the respiration rate of minimally processed organic carrots (Daucus Carota L. cv. Brasília)

The objective of this work was to study the influence of temperature on the respiration rate of minimally processed organic carrots (Daucus Carota L. cv. Brasília) with and without the application of a gelatin film. The samples were packed in flexible bags and stored at 1, 5 and 10 °C. During the five days of storage, the CO2 and O2 concentrations in the headspace of the package were monitored by gas chromatography, and the mathematical model based on enzymatic kinetics was used to estimate the respiration rate of minimally processed organic carrots. The effect of temperature on the respiration rate was evaluated by the Arrhenius equation. The results showed that the O2 concentration decreased during the storage period and the CO2 concentration increased. The lowest O2 concentrations of 2.59 and 2.66% were found for the samples stored at 10 °C with and without the film, respectively. For the CO2 concentration, the highest concentrations of 16.25 and 16.32% were again found for the temperature of 10 °C with and without the application of the film, respectively. At the temperature of 1 °C, the maximum respiratory rates for the samples without and with the film were 10.82 and 10.44 mL CO2.kg-1/hour, respectively, after 72 hours of storage. The greatest respiratory rate was obtained at 10 °C, the maximum peak being reached after 50 hours. Activation energy values were of 50.59 kJ.mol-1, for the samples with the film, and 51.88 kJ.mol-1 for the samples without the film.

Effect of different sweetener blends and fat types on ice cream properties

The development of processed foods requires the understanding of the phenomena that dictate the ingredient interactions normally used in food formulations, as well as the effects of the numerous operations involved in the processing of the final product. In ice creams, sugars are responsible for taste, but they also affect the freezing behavior and viscosity of processed mixes. Components such as fats influence mechanical properties, melting resistance, and palatability of final products. The objective was to study the technological effects of different sugars and fats on the structure of ice cream formulations. Fructose syrup was used as a substitute for glucose syrup in blends with sucrose, and palm fat was employed as an alternative to hydrogenated vegetable fat. The analysis of variance showed significant differences in chemical compositions. Hygroscopicity of fructose syrup increased the solids content in the formulations. Melting rate and overrun were higher in products added with this sugar. Palm fat caused changes in melting ranges of formulations, and higher melting rate was observed in the combination of palm fat and fructose syrup.

Microstructural changes of frozen strawberries submitted to pre-treatments with additives and vacuum impregnation

Strawberries were submitted to freezing after pre-treatments with hydrocolloid and calcium salts (pectin and calcium chloride) at different concentrations, in the attempt to establish a correlation of the effects of these substances and their processing, on the physical and microstructural characteristics of fruits after thawing. Strawberry halves were submitted to impregnation with controlled vacuum pressure of 84.4, 50.5 and 16.6 kPa; comprising pectin at concentrations of 0, 1.5 and 3%; with the addition of calcium chloride at concentrations of 0, 3 and 6%; and glucose at 20%, for 4 hours. Measurements were made of the total soluble solid contents, cellular fluid loss, texture and viscosity of the solution, before and after the freezing/thawing. Images of the tissue cuts during the freezing, in function of time, were taken in an optic microscope coupled to a cold-stage and controlled temperature system, where the reduction of the cellular area was quantified using an image analyzing software. The pectin concentration had an influence on and demonstrated a potential for protection of the frozen tissue samples. The photomicrographs showed that the loss of cellular fluid occurs during the growth of ice formed in the intercellular spaces and it is retarded through treatments with high pectin concentrations.

Corn germ with pericarp in relation to whole corn: nutrient contents, food and protein efficiency, and protein digestibility-corrected amino acid score

The germ fraction with pericarp (bran) is generated in the industrial processing of corn kernel, and it is used for oil extraction and animal feed. This study evaluated the nutritional and protein quality of this fraction in relation to whole corn. The proximate composition, mineral contents, and amino acid profile of the germ fraction with pericarp and of whole corn were determined. A 4-week experiment was conducted using 36 weanling male Wistar rats, and three 10%-protein diets (reference, germ with 15% lipids and casein with 15% lipids), two 6%-protein diets (whole corn and casein), and a protein-free diet were prepared. The germ showed higher contents of proteins, lipids, dietary fiber (27.8 g.100 g-1), ash, minerals (Fe and Zn- approximately 5 mg.100 g-1), and lysine (57.2 mg.g-1 protein) than those of corn. The germ presented good quality protein (Relative Protein Efficiency Ratio-RPER = 80%; Protein Digestibility-Corrected Amino Acid Score-PDCAAS = 86%), higher than that of corn (RPER = 49%; PDCAAS = 60%). The corn germ fraction with pericarp is rich in dietary fiber, and it is a source of good quality protein as well as of iron and zinc, and its use as nutritive raw material is indicated in food products for human consumption.

Lipid and protein oxidation in the internal part of italian type salami containing basil essential oil (Ocimum basilicum L.)

Different concentrations of basil essential oil (Ocimum basilicum L.) (0.19; 0.38; 0.75; 1.87; 3.75 and 6.00 mg.g-1) were evaluated in relation to their antioxidant activity using the DPPH● radical methodology. From the IC50 obtained data, the concentrations of 0.19; 0.38; 0.75; 1.87; 3.75; 6.00 and 12.00 mg.mL-1 were applied directly to the product and these were sensorially evaluated by the test of control difference. The concentrations related to the highest acceptability (0.19; 0.38 and 0.75 mg.g-1) were tested for antioxidant activity in the internal part of Italian type salami - during the processing and after 30 days of storage, in terms of lipid and protein oxidation. The oxidation of lipids was determined using the method of TBARS. The method of carbonyl compounds was employed for proteins oxidation. Five different formulations of salami were elaborated: blank (without the use of antioxidant); control (using sodium eritorbate as antioxidant); and adding 0.19; 0.38 and 0.75 mg.g-1 of basil essential oil. The product was kept between 25 ºC and 18 ºC and UR between 95% and 70%, for 28 days. Analyses were carried out on the processing day and after 2, 7, 14, 21 and 28 days, and also following 30 days of storage. The basil essential oil in vitro presented an antioxidant activity of IC50 12 mg.mL-1. In the internal part of the Italian type salami the commercial antioxidant (control) and the formulation containing 0.75 mg.g-1 of basil essential oil presented antioxidant activity in relation to the lipids, but not to the proteins - during processing and storage.

In natura açaí beverage: quality, pasteurization and acidification

The purpose of this work was to evaluate the physical, physicochemical, chemical and microbiological characteristics of in natura açai (Euterpe precatoria Mart.)beverageprocessed and commercialized in Rio Branco, Acre, submitting it to acidification and pasteurization treatments and evaluating their effects. Açaí fruits were processed to obtain the beverage as generally consumed. A 25 L sample was collected from a processing unit at a market in Rio Branco and transported to the Laboratory of Food Technology at the Federal University of Acre, for sampling of the experiments in a completely randomized design. Analyses of total solids, pH, total titrable acidity, proteins, lipids, moulds and yeasts, total and heat-tolerant coliforms at 45 ºC were performed in in natura beverage and after treatments. The results of the ANOVA showed, except for lipids, difference (p < 0.01) in the parameters. The in natura açaí beverage presented an elevated contamination by total and heat-tolerant coliforms at 45 ºC, moulds and yeasts, being in hygienic-sanitary conditions both unsatisfactory and unsafe for consumption. Pasteurization was efficient in reducing the beverage microbiota; it reduced contamination to an acceptable level according to the legislation, warranting food quality and safety. The acidified treatment partially reduced the microbiota. The beverage was classified as fine or type C.

Identification of fatty foods with contamination possibilities by plasticizers when stored in PVC film packaging

Poly-(vinyl chloride) (PVC) requires the addition of plasticizers - additives that give flexibility and malleability for its processing into flexible film. The most used ones are: di-(2-ethylhexyl) adipate (DEHA) and di-(2-ethylhexyl) phthalate (DEHP). Toxic effects of DEHP have been observed by several authors. Phthalates are being replaced by alternative substances in PVC flexible products, because of their possible toxicological effects. DEHA is a substitute for phthalates widely used as a plasticizer in PVC materials for involving food. Some authors have shown that the exposure to DEHA also induces toxicity. A cross-sectional study was performed to identify which fatty foods carry the possibility of contamination by DEHP and DEHA. Eighteen different foods with at least 3% (m/m) fat and the possibility of being wrapped in plastic film were determined. This study suggested that all foods were subject to contamination by DEHP and DEHA in those conditions - in decreasing consumption order of 96 to 22% in the convenience sample. New guidelines on the limits of DEHA and DEHP established by the Brazilian legislation, as additives in PVC film for packaging fatty food, are still relevant to ensure human health.

Influence of packaging and potassium sorbate on the physical, physicochemical and microbiological alterations of guava preserves

The elaboration of preserves through fruit processing is a promising alternative for their conservation. Such processing provides pleasant flavor due to the increase of sweetness and allows good conservation of the product for a prolonged time. Seeking quality and higher durability of fruit preserves, the purpose of this work was to evaluate the interference of potassium sorbate addition, and polypropylene, metallic and cellophane film packaging on the quality of guava (Psidium guajava L.) preserves during storage, through the physical, physiochemical and microbiological characteristics. The physical, physiochemical and microbiological analyses showed that the different types of packaging did not interfere in the stability of the guava preserves until the 5th month of storage - time being the factor that most influences the quality of the preserves when stored under temperature and humidity of 19.6 °C and 76.2%, respectively. The potassium sorbate caused an increase of the soluble solid levels and a decrease of the water activity. Regardless of the treatment, the preserves remained microbiologically stable during storage.

Influence of the fungi population on the physicochemical and chemical composition of coffee (Coffea arabica L.)

The influence of fungi associated with coffee fruits was verified regarding the chemical and physicochemical composition of Coffea arabica L. raw grains. The fruits were harvested at EPAMIG Experimental farm in Lavras, State of Minas Gerais - making up the different samples here analyzed. After processing and drying, the grains were incubated in wet chamber for fungal exteriorization through the blotter test method and submitted to the following analyses: polyphenoloxidase, total reducing and non-reducing sugars, clorogenic acid, titrable acidity, potassium leaching, electric conductivity and caffeine. The occurrence of the P. variable, P. rugulosum, P. funiculosum, F. equiseti, F. semitectum, A.alutaceus, A. niger and C. cladosporioides fungi in the different samples was detected. From the analysis of the results obtained, it was observed that the presence of the Aspergillus alutaceus fungus reduces the activity of the enzyme polyphenoloxidase and increases the values of potassium leaching, electric conductivity and chlorogenic acid. The incidence of the Cladosporium cladosporioides fungus influenced the average values of potassium leaching and electric conductivity.

Modified broken rice starch as fat substitute in sausages

The demand for low-fat beef products has led the food industry to use fat substitutes such as modified starch. About 14% of broken rice is generated during processing. Nevertheless, this by-product contains high levels of starch; being therefore, great raw material for fat substitution. This study evaluated the applicability of chemically and physically modified broken rice starch as fat substitute in sausages. Extruded and phosphorylated broken rice was used in low-fat sausage formulation. All low-fat sausages presented about 55% reduction in the fat content and around 28% reduction in the total caloric value. Fat replacement with phosphorylated and extruded broken rice starch increased the texture acceptability of low-fat sausages, when compared to low-fat sausages with no modified broken rice. Results suggest that modified broken rice can be used as fat substitute in sausage formulations, yielding lower caloric value products with acceptable sensory characteristics.

Some functional characteristics of extruded blends of fiber from sugarcane bagasse, whey protein concentrate, and corn starch

Blends of fiber from sugar cane bagasse, corn starch, and whey protein concentrate were extruded. A single screw extruder, equipped with a screw at a constant compression ratio of 1:1 and a die diameter of 3 mm, was used. The best processing conditions were determined according to a central composite rotatable design (α = 1.41) with 5 central points, which gives a total of 13 tests. During the extrusion process the content of insoluble fiber decreased and that of soluble fiber increased. An increase in the contents of fiber and in the barrel temperature resulted in a decrease in the expansion index values and an increase in the water absorption index values; whereas in blends with intermediate fiber contents the effects in these parameters were found to be the opposite. High fiber contents increased penetration force but decreased luminosity, water solubility index values and the adhesive force in gels. The extrusion process improved the functional properties of sugarcane fiber bagasse enabling its addition to diverse alimentary systems.

Construction of 2D transparent micromodels in polyester resin with porosity similar to carrots

Microscopic visualization, especially in transparent micromodels, can provide valuable information to understand the transport phenomena at pore scale in different process occurring in porous materials (food, timber, soils, etc.). Micromodels studies focus mainly on the observation of multi-phase flow, which presents a greater proximity to reality. The aim of this study was to study the process of flexography and its application in the manufacture of polyester resin transparent micromodels and its application to carrots. Materials used to implement a flexo station for micromodels construction were thermoregulated water bath, exposure chamber to UV light, photosensitive substance (photopolymer), RTV silicone polyester resin, and glass plates. In this paper, data on size distribution of a particular kind of carrot we used, and a transparent micromodel with square cross-section as well as a Log-normal pore size distribution with pore radii ranging from 10 to 110 µm (average of 22 µm and micromodel size of 10 × 10 cm) were built. Finally, it stresses that it has successfully implemented the protocol processing 2D polyester resin transparent micromodels.

Optimization of extrusion process for production of nutritious pellets

A blend of 50% Potato Starch (PS), 35% Quality Protein Maize (QPM), and 15% Soybean Meal (SM) were used in the preparation of expanded pellets utilizing a laboratory extruder with a 1.5 × 20.0 × 100.0 mm die-nozzle. The independent variables analyzed were Barrel Temperature (BT) (75-140 °C) and Feed Moisture (FM) (16-30%). The effect of extrusion variables was investigated in terms of Expansion Index (EI), apparent density (ApD), Penetration Force (PF) and Specific Mechanical Energy (SME), viscosity profiles, DSC, crystallinity by X-ray diffraction, and Scanning Electronic Microscopy (SEM). The PF decreased from 30 to 4 kgf with the increase of both independent variables (BT and FM). SME was affected only by FM, and decreased with the increase in this variable. The optimal region showed that the maximum EI was found for BT in the range of 123-140 °C and 27-31% for FM, respectively. The extruded pellets obtained from the optimal processing region were probably not completely degraded, as shown in the structural characterization. Acceptable expanded pellets could be produced using a blend of PS, QPM, and SM by extrusion cooking.