Produção de misturas betuminosas a quente com incorporação de material fresado

A incorporação de materiais reciclados na construção de estradas, como substituição de materiais virgens é percebida como uma oportunidade de economizar recursos, e evitar o impacto associado à sua extração e transporte. Desta forma, a incorporação de material fresado (do termo inglês RAP - Reclaimed Asphalt Pavement) em misturas betuminosas produzidas a quente em central tem sido uma alternativa satisfatória. Neste trabalho, foram estudadas três misturas betuminosas do tipo macadame betuminoso (AC 20 base 35/50), tradicional e com taxas de incorporação de RAP de 10% e 20%, com o objetivo de efetuar uma análise comparativa do seu comportamento. Começou-se por realizar um estudo Marshall de forma a determinar a percentagem ótima de betume a usar em cada mistura e, posteriormente, a composição foi transposta para central para o seu fabrico. No final foram realizados ensaios de caracterização mecânica sobre as misturas para avaliar o seu desempenho, através de ensaios de sensibilidade à água, módulo de rigidez, resistência à fadiga e à deformação permanente. Esta dissertação teve o apoio da empresa Tecnovia – Sociedade de Empreitadas S.A., com a disponibilização de instalações e materiais para o trabalho experimental. De acordo com os resultados obtidos, é possível concluir que as misturas recicladas apresentaram um comportamento satisfatório, quando comparado com as misturas tradicionais.

The use of technology in Portuguese hospitals- The case of MRI

We study the determinants of MRI use across Portuguese NHS hospitals for patients belonging to specific DRGs. Using data on individual hospital admissions, we estimate a probit model including individual-, hospital-, time- and region-specific variables in order to explain the probability of a patient being sent for MRI. Results convey a tightening effect on the hospital’s budget constraint in the end of each year. Hospitals seem to account for regional characteristics when defining adoption patterns. Individual-specific variables are good predictors of MRI use. Measures taken by the Government only impact the short run. Finally, the gains from an MRI scan, as far as the probability of death is concerned, occur mainly for less severe patients.

Using mobile technology to conduct epidemiological investigations

INTRODUCTION : The aim of this study was to report the experience of an epidemiological field survey for which data were collected and analyzed using tablets. METHODS : The devices used Epi Info 7 (Android version), which has been modeled a database with variables of the traditional form. RESULTS : Twenty-one households were randomly selected in the study area; 75 residents were registered and completed household interviews with socioeconomic and environmental risk variables. CONCLUSIONS : This new technology is a valuable tool for collecting and analyzing data from the field, with advantageous benefits to epidemiological surveys.

Conservar depois da catástrofe. O caso dos documentos queimados do antigo Arquivo Histórico do Museu Bocage: caracterização material e proposta de um protocolo de intervenção

Tendo como caso de estudo um conjunto documental do Arquivo Histórico dos Museus da Universidade de Lisboa (AHMUL) – Museu Nacional de História Natural e da Ciência (MUHNAC), anteriormente fazendo parte do antigo Arquivo Histórico do Museu Bocage – fortemente atingido por um incêndio em 1978, o objectivo principal desta investigação é dar início à pesquisa e explorar a possibilidade de aplicação de métodos não invasivos de restauro digital, como a técnica de digitalização volumétrica (volumetric scanning), para a recuperação da informação escrita na parte mais deteriorada do arquivo; e propor métodos de estabilização/recuperação do seu suporte físico, usando técnicas tradicionais de conservação e restauro. Assim, o objectivo deste estudo não é apenas rever métodos de recuperação da informação para estes documentos tidos como perdidos, mas também propor uma forma de recuperar, tanto quanto possível, o seu suporte original. Será realizada a caracterização material da colecção, com recurso a métodos de exame e análise e o diagnóstico de conservação da parte da colecção mais deteriorada, bem como uma contextualização histórica sobre o arquivo e as condições do incêndio. Como conclusões principais salienta-se a confirmação da possibilidade de aplicação de técnicas de digitalização, os resultados promissores de outras técnicas como a fotografia de infravermelho com recurso adicional a software de processamento da imagem e o uso da imagem multiespectral em documentos carbonizados, além do estabelecimento de uma proposta de protocolo de intervenção para documentos queimados, com recurso a dois éteres de celulose, com diferentes solventes (água e etanol) de acordo com a solubilidade dos meios de escrita. Pretendeu-se ainda com este estudo contribuir para a divulgação da existência deste fundo do AHMUL em específico, tendo sido fundamental a realização, após 37 anos, do primeiro registo e compilação de fontes documentais sobre o incêndio de 18 de março de 1978, um facto tão relevante para a Memória do MUHNAC e dos Museus de Portugal.

Valorization of olive pomace through combination of biocatalysis with supercritical fluid technology

A supercritical carbon dioxide (scCO2) based oil extraction method was implemented on olive pomace (alperujo), and an oil yield of 25,5 +/- 0,8% (goil/gdry residue) was obtained. By Soxhlet extraction with hexane, an oil extraction yield of 28,9 +/- 0,8 % was obtained, which corresponds to an efficiency of 88,4 +/- 4,8 % for the supercritical method. The scCO2 extraction process was optimized for operating conditions of 50 MPa and 348,15 K, for which an oil loading of 32,60 g oil/kg CO2 was calculated. As a proof of concept, olive pomace was used as feedstock for biodiesel production, in a process combining the use of lipase as a catalyst with the use of scCO2 as a solvent, and integrating the steps of oil extraction, oil to biodiesel transesterification and subsequent separation of the latter. In the conducted experiments, FAME (fatty acid methyl ester) purities of 90% were obtained, with the following operating parameters: an oil:methanol molar ratio of 1:24; a residence time of 7,33 and 11,6 mins; a pressure of 40 MPa; a temperature of 313,15 K; and Lipozyme (Mucor miehei; Sigma-Aldritch) as an enzyme. However, oscillations of FAME purity were registered throughout the experiments, which could possibly be due to methanol accumulation in the enzymatic reactor. Finally, the phenolic content of olive pomace, and the effect of the drying process – oven or freeze-drying – and the extraction methods – hydro-alcoholic method and supercritical method – on the phenolic content were analysed. It was verified that the oven-drying process on the olive pomace preserved 90,1 +/- 3,6 % of the total phenolic content. About 62,3 +/- 5,53% of the oven-dried pomace phenolic content was extracted using scCO2 at 60 MPa and 323,15 K. Seven individual phenols – hydroxytyrosol, tyrosol, oleuropein, quercetin, caffeic acid, ferulic acid and p-coumaric acid – were identified and quantified by HPLC.

AS COSTUREIRAS, AS QUEENS E OS SEUS MANTOS: DESTERRITORIALIZAÇÃO, CULTURA MATERIAL E CONSTRUÇÃO DO LUGAR

Durante as décadas de 1980 e de 1990 a noção de lugar foi, na literatura antropológica, sujeita a uma abordagem crítica que debateu as dimensões metodológicas e conceptuais envolvidas na sua construção. No seguimento dessa abordagem, surgiram propostas de trabalho que, de maneiras muito diversas, conseguiram ultrapassar as limitações das concepções mais clássicas da figura do lugar. Essas propostas revelaram, no entanto, que mesmo quando estamos face a uma lógica de desterritorialização, a figura do lugar pode reaparecer (embora obviamente transmutada, visto construir-se no interior de outras lógicas sociais, culturais e económicas). Partindo de uma etnografia realizada na Ilha do Pico, o texto explora algumas das inovações, provenientes dos EUA no início do século XX, que foram introduzidas nas Festas do Espírito Santo. A principal inovação prende-se com a emergência de novos personagens: as rainhas (“queens”) coroadas durante o ritual, seguidas pelas costureiras indispensáveis à confecção dos seus vestidos e mantos. Centrado nos processos de feitura dos mantos, o texto pretende mostrar como a cultura material local se constrói e se transforma no interior de um movimento transcontinental constante de pessoas, rituais, coisas e técnicas. Num contexto transnacional, a mobilidade das pessoas pode objetificar-se em coisas que são feitas localmente, participando assim a desterritorialização na construção do lugar.

Historic and potential technology transition paths of grid battery storage: Co-evolution of energy grid, electric mobility and batteries

Scarcity of fuels, changes in environmental policy and in society increased the interest in generating electric energy from renewable energy sources (RES) for a sustainable energy supply in the future. The main problem of RES as solar and wind energy, which represent a main pillar of this transition, is that they cannot supply constant power output. This results inter alia in an increased demand of backup technologies as batteries to assure electricity system safety. The diffusion of energy storage technologies is highly dependent on the energy system and transport transition pathways which might lead to a replacement or reconfiguration of embedded socio-technical practices and regimes (by creating new standards or dominant designs, changing regulations, infrastructure and user patterns). The success of this technology is dependent on hardly predictable future technical advances, actor preferences, development of competing technologies and designs, diverging interests of actors, future cost efficiencies, environmental performance, the evolution of market demand and design and evolution of our society.

Geopolymers as infill material for conservation of azulejos

The restoration materials currently used to fill gaps in architectural historical azulejos (e.g. lime or organic resin pastes) usually show serious drawbacks in terms of compatibility, effectiveness and durability. The existing solutions do not fully protect azulejos in outdoor conditions and frequently result in further deterioration. Geopolymers can be a potential solution for azulejo lacunae infill given the chemical-mineralogical similitude to the ceramic body, and also the durability and versatile range of physical properties that can be obtained through the manipulation of their formulation and curing conditions. This work presents and discusses the viability of the use of geopolymeric pastes to fill lacunae in azulejos or to act as “cold” cast ceramic tile surrogates reproducing missing azulejo fragments. The formulation of geopolymers, namely the type of activators, the aluminosilicate source, the amount of water (to meet adequate workability requirements) and curing conditions were studied. The need for post-curing desalination was also considered envisaging their application in the restoration of outdoor architectural historical azulejos frequently exposed to adverse environmental conditions. The possible advantages and disadvantages of the use of geopolymers in the conservation of azulejos are also discussed. Several techniques were used to study the chemical and physical behavior of geopolymers, namely FT-IR, XRD, MIP, SEM-EDS, WDXRF, electrical conductivity, open porosity, bending strength, adhesion strength, water vapour permeability, thermal expansion and hydric expansion. The results indicate that geopolymers are a promising material for restoration of azulejos, exhibiting some properties, such as adhesion to the ceramic substrate, higher than inorganic materials used nowadays, such as aerial lime based pastes.

Al-doped ZnO ceramic sputtering targets based on nanocrystalline powders produced by emulsion detonation synthesis – deposition and application as a transparent conductive oxide material

Transparent conducting oxides (TCOs) have been largely used in the optoelectronic industry due to their singular combination of low electrical resistivity and high optical transmittance. They are usually deposited by magnetron sputtering systems being applied in several devices, specifically thin film solar cells (TFSCs). Sputtering targets are crucial components of the sputtering process, with many of the sputtered films properties dependent on the targets characteristics. The present thesis focuses on the development of high quality conductive Al-doped ZnO (AZO) ceramic sputtering targets based on nanostructured powders produced by emulsion detonation synthesis method (EDSM), and their application as a TCO. In this sense, the influence of several processing parameters was investigated from the targets raw-materials synthesis to the application of sputtered films in optoelectronic devices. The optimized manufactured AZO targets present a final density above 99 % with controlled grain size, an homogeneous microstructure with a well dispersed ZnAl2O4 spinel phase, and electrical resistivities of ~4 × 10-4 Ωcm independently on the Al-doping level among 0.5 and 2.0 wt. % Al2O3. Sintering conditions proved to have a great influence on the properties of the targets and their performance as a sputtering target. It was demonstrated that both deposition process and final properties of the films are related with the targets characteristics, which in turn depends on the initial powder properties. In parallel, the influence of several deposition parameters in the film´s properties sputtered from these targets was investigated. The sputtered AZO TCOs showed electrical properties at room temperature that are superior to simple oxides and comparable to a reference TCO – indium tin oxide (ITO), namely low electrical resistivity of 5.45 × 10-4 Ωcm, high carrier mobility (29.4 cm2V-1s-1), and high charge carrier concentration (3.97 × 1020 cm-3), and also average transmittance in the visible region > 80 %. These superior properties allowed their successful application in different optoelectronic devices.

Torrefação de biomassa de Arundo donax L. e de Phoenix canariensis com vista à sua valorização energética ou material

A torrefação é vista como um pré-tratamento térmico que introduz modificações na biomassa, ou em resíduos de biomassa, que facilitam o seu processamento mecânico e aumentam a sua estabilidade e densidade energética, potenciando, assim, uma valorização posterior. Neste trabalho, estudou-se o impacte da torrefação na gama de 200 a 350 ºC e tempos de residência entre 15 e 90 min nas propriedades da biomassa proveniente da herbácea Arundo donax L. e das palmeiras Phoenix canariensis, espécies muito abundantes em vários locais do país, tendo em vista a sua posterior valorização. A proliferação descontrolada do arundo e a praga do escaravelho das palmeiras leva a que estas espécies sejam alvo de frequentes operações de remoção. A sua estrutura altamente fibrosa dificulta e encarece estas operações, que acarretam custos significativos para as câmaras municipais, e não se conhecem medidas para a sua valorização material ou energética. A torrefação foi também aplicada a peletes de resíduos de pinheiro, na gama de 200 a 250 ºC e com tempos de residência de 30 e 60 min, para averiguar o seu impacte na qualidade desse biocombustível sólido. A torrefação permitiu obter peletes mais resistentes à biodegradação, devido à redução do teor de humidade para valores residuais, sem aumentar significativamente o seu teor de cinzas e sem afetar de forma relevante a sua durabilidade, o teor de finos ou a densidade aparente. Com a biomassa de arundo e de palmeira obtiveram-se produtos com maior poder calorífico e com melhor moabilidade. No entanto, a acentuada diminuição dos rendimentos mássico e energético e o elevado teor de cinzas constrangem a sua utilização como biocombustíveis sólidos. Desta forma, optou-se por testar a sua valorização como adsorventes do corante azul de metileno, bastante comum, por exemplo, na indústria têxtil, nos curtumes ou nas industrias do papel. Os estudos de adsorção revelaram maior afinidade pelo corante por parte da biomassa sujeita a torrefação mais ligeira, com eficiências de remoção muito próximas das do carvão ativado comercial, para concentrações iniciais de corante até 200 mg/L. As isotérmicas foram melhor ajustadas ao modelo de Langmuir, que revelou capacidades máximas de adsorção na monocamada entre 59,92 e 92,68 mg/g, tendo as curvas de cinética sido melhor descritas pelo modelo de pseudo-segunda ordem. A adsorção é bastante rápida nos primeiros minutos, essencialmente devido a atrações eletrostáticas, sendo inicialmente controlada pela difusão no filme e depois pela difusão nos poros. Os adsorventes revelaram seletividade por um corante catiónico e permitiram dessorção de corante, ao contrário do verificado com o carvão ativado comercial, o que é um aspeto da maior relevância tendo em mente a regeneração do adsorvente e a recuperação do corante.

ReedCob – An eco-efficient building technology for monolithic walls based on earth and reeds

4th Conference COST ACTION FP1303 – Designing with Bio-based Materials – Challenges and opportiunities. INIA – CSIC, Madrid, 24-25 February 2016. Book of abstracts, T.Troya, J.Galván, D.Jones (Eds.), INIA and IETcc – CSIS, pg. 79-80 (ISBN: 978-91-88349-16-3)

Amadeus IT holdings information technology

Equity research report

Royal Philips Medical Technology

Equity research report

Decisions of technology innovation: the role of indicators

This work presents research conducted to understand the role of indicators in decisions of technology innovation. A gap was detected in the literature of innovation and technology assessment about the use and influence of indicators in this type of decision. It was important to address this gap because indicators are often frequent elements of innovation and technology assessment studies. The research was designed to determine the extent of the use and influence of indicators in decisions of technology innovation, to characterize the role of indicators in these decisions, and to understand how indicators are used in these decisions. The latter involved the test of four possible explanatory factors: the type and phase of decision, and the context and process of construction of evidence. Furthermore, it focused on three Portuguese innovation groups: public researchers, business R&D&I leaders and policymakers. The research used a combination of methods to collect quantitative and qualitative information, such as surveys, case studies and social network analysis. This research concluded that the use of indicators is different from their influence in decisions of technology innovation. In fact, there is a high use of indicators in these decisions, but lower and differentiated differences in their influence in each innovation group. This suggests that political-behavioural methods are also involved in the decisions to different degrees. The main social influences in the decisions came mostly from hierarchies, knowledge-based contacts and users. Furthermore, the research established that indicators played mostly symbolic roles in decisions of policymakers and business R&D&I leaders, although their role with researchers was more differentiated. Indicators were also described as helpful instruments to conduct a reasonable interpretation of data and to balance options in innovation and technology assessments studies, in particular when contextualised, described in detail and with discussion upon the options made. Results suggest that there are four main explanatory factors for the role of indicators in these decisions: First, the type of decision appears to be a factor to consider when explaining the role of indicators. In fact, each type of decision had different influences on the way indicators are used, and each type of decision used different types of indicators. Results for policy-making were particularly different from decisions of acquisition and development of products/technology. Second, the phase of the decision can help to understand the role indicators play in these decisions. Results distinguished between two phases detected in all decisions – before and after the decision – as well as two other phases that can be used to complement the decision process and where indicators can be involved. Third, the context of decision is an important factor to consider when explaining the way indicators are taken into consideration in policy decisions. In fact, the role of indicators can be influenced by the particular context of the decision maker, in which all types of evidence can be selected or downplayed. More importantly, the use of persuasive analytical evidence appears to be related with the dispute existent in the policy context. Fourth and last, the process of construction of evidence is a factor to consider when explaining the way indicators are involved in these decisions. In fact, indicators and other evidence were brought to the decision processes according to their availability and capacity to support the different arguments and interests of the actors and stakeholders. In one case, an indicator lost much persuasion strength with the controversies that it went through during the decision process. Therefore, it can be argued that the use of indicators is high but not very influential; their role is mostly symbolic to policymakers and business decisions, but varies among researchers. The role of indicators in these decisions depends on the type and phase of the decision and the context and process of construction of evidence. The latter two are related to the particular context of each decision maker, the existence of elements of dispute and controversies that influence the way indicators are introduced in the decision-making process.

Material Zoológico depositado nas coleções sistemáticas de entomologia do INPA, resultante do "Projeto INPA/MAX-PLANK" (Convênio CNPq/MGP)

As coleções de Entomolologia Sistemática do Instituto nacional de Pesquisas da Amazônia (INPA) em Manaus, Brasil, no momento, contém aproximadamente 16.350 exemplares de invertebrados e vertebrados identificados, representando 330a espécies e incluindo 692 tipos que foram depositados entre 1940 e 1982 por pesquisadores e associados do Instituto Max-Planck de Limnologia em Plön, Alemanha Ocidental.