998 resultados para dosagem a vácuo


Relevância:

10.00% 10.00%

Publicador:

Resumo:

O uso de cápsulas porosas para extração de solução do solo é interessante por ser um ensaio não-destrutivo. Entretanto, persistem dúvidas sobre a liberação de íons da própria cápsula, que podem contaminar a solução extraída. Foram realizados testes na Faculdade de Ciências Agronômicas/UNESP, Botucatu (SP), com o objetivo de verificar a liberação de Ca e de Mg por cápsulas porosas de porcelana. No primeiro, foram empregados quatro tratamentos: T1 - lavagem das cápsulas com água destilada, forçando sua passagem pelas cápsulas, utilizando uma bomba a vácuo; T2 - lavagem das cápsulas com HCl 0,1 mol L-1, forçando sua passagem pelas cápsulas, utilizando uma bomba a vácuo; T3 - lavagem das cápsulas com água destilada, sem vácuo, e T4 - lavagem das cápsulas com HCl 0,1 mol L-1, sem vácuo, em um tempo de imersão de 24 h (para T3 e T4). No segundo teste, as cápsulas tratadas com HCl 0,1 mol L-1 no primeiro teste foram lavadas com água destilada novamente e deixadas de molho em água destilada e deionizada durante 45 min. Após estes procedimentos, as cápsulas foram imersas em água destilada, tomando-se alícotas desta solução para determinação de pH e dos teores de Ca e Mg após contato com as cápsulas por 0; 0,5; 1,0; 2,0; 4,0 e 24 h. Cada tratamento teve quatro repetições. Não se observou liberação significativa de Ca e Mg das cápsulas porosas para a solução, quando foram preparadas utilizando-se da passagem de HCl 0,1 mol L-1 a vácuo e água destilada, e deixadas, a seguir, em água destilada e deionizada durante 4 h.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

O objetivo deste trabalho foi avaliar o efeito de plantas de cobertura e da calagem sobre a produtividade da soja e as características químicas do perfil do solo, após implantação do plantio direto. O experimento foi realizado em campo por dois anos, em Latossolo Vermelho‑Amarelo. A área era explorada como pastagem há cinco anos. Avaliaram-se três sistemas de cultivo: soja/pousio/soja, soja/Pennisetum glaucum/soja e soja/Urochloa ruziziensis/soja, com aplicação de calcário à dosagem de 0, 0,5, 1,0 e 2,0 vezes a quantidade necessária para elevar a saturação de bases (V) a 50%, na camada de 0-20 cm. O calcário foi incorporado ao solo, a 20 cm de profundidade, previamente à implantação dos sistemas de cultivo. Aos 490 dias após a calagem, foram coletadas amostras de solo das profundidades de 0-­10, 10-­20, 20-­40 e 40­-60 cm. Avaliaram-se o estado nutricional das plantas, as alterações das características químicas do solo e a produtividade da soja. As plantas de cobertura associadas à calagem promovem melhorias nos parâmetros de acidez do solo - sobretudo quando a dose aplicada é igual ou mais elevada do que a recomendada para V 50% -, e aumentam o teor foliar de P e a produtividade da soja, independentemente da calagem. Quanto maior a dose de calcário, maior é o avanço da frente alcalina no solo e a produtividade de grãos.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Objetivou-se com este trabalho avaliar a eficiência de pontas de pulverização com diferentes vazões e tamanhos de gotas na deposição e na dessecação de plantas de Brachiaria brizantha cv. Marandu, além da quantificação das perdas da calda de pulverização para o solo. O delineamento experimental adotado foi o de blocos casualizados, com quatro repetições. Cada unidade experimental constituiu-se de três linhas de 5 m de comprimento, espaçadas de 1 m. A aplicação dos tratamentos foi realizada 16 meses após a semeadura da braquiária; 40 dias antes da aplicação foi realizada uma roçagem para uniformização da área. Foram avaliadas as pontas de pulverização de jato plano XR 11001 VS (100 L ha-1) e XR 11002 VS (200 L ha-1), jato cônico TX-4VS (100 L ha-1) e TX-8 VK (200 L ha-1), ponta com indução de ar AI 11002 VS (200 L ha-1) e jato plano duplo TJ60 11002 VS (200 L ha-1). A calda foi aplicada com o herbicida glyphosate na dose de 1.800 g ha-1, mais um traçador (FD&C nº1 2.000 ppm). Foram coletados imediatamente após a aplicação da calda 25 perfilhos por repetição, sendo lavadas separadamente as folhas e caules de cada perfilho em 150 ml de água destilada, para posterior quantificação do traçador em espectrofotômetro. Os dados foram ajustados à curva de regressão pelo modelo de Gompertz. Todas as pontas utilizadas foram eficientes na dessecação das plantas de B. brizantha, independentemente do volume utilizado, o que evidencia a possibilidade de redução do volume de aplicação e da dosagem do herbicida na dessecação de pastagens, considerando-se a utilização de herbicidas sistêmicos. Ressalta-se que houve diferença na quantidade e na uniformidade de distribuição da calda pulverizada nos alvos avaliados em função da ponta testada e, conseqüentemente, do volume utilizado.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Objetivou-se avaliar a produção de fitomassa, teor e produtividade do óleo essencial de Baccharis dracuculifolia DC., em função de doses de adubo orgânico, e foram utilizadas mudas produzidas por semente, e mantidas sob sombrite pelo período de 84 dias até serem transplantadas para o campo, no espaçamento de 1,0 x 1,0 m, com irrigação por gotejamento. O delineamento estatístico utilizado foi em blocos ao acaso, com quatro repetições, e as doses de composto orgânico foram: 0, 10, 20, 30, 40 e 50 t ha-1. Foi realizada uma colheita, aos 150 dias após o transplante das mudas. O óleo essencial foi extraído por hidrodestilação e analisado em cromatógrafo a gás acoplado a espectrômetro de massas (Shimadzu, QP-5000). Todos os resultados foram submetidos à análise de variância pelo teste F seguido da análise de regressão e o teste Tukey para os dados: massa seca útil da parte aérea, teor e produtividade do óleo essencial. Para as variáveis massa seca total e massa seca útil da parte aérea, as dosagens estudadas influenciaram as plantas, que apresentaram os melhores resultados na dose 50 t ha-1. Para teor de óleo não houve influência significativa para as dosagens estudadas, porém a dose 30 t ha-1 apresentou o melhor resultado. Entretanto para a produtividade do óleo essencial, as dosagens estudadas influenciaram as plantas, que na dosagem 30 t ha-1 obtiveram os melhores resultados.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Teve-se o objetivo de avaliar as formas de se misturar o lubrificante sólido grafite nas sementes de milho, as dosagens e a influência desse na distribuição longitudinal e na germinação, em sementes sem e com tratamento fitossanitário, em mecanismo dosador com disco perfurado horizontal. Os fatores analisados foram: distribuição longitudinal das sementes (espaçamentos falhos, múltiplos e aceitáveis) e a porcentagem de germinação aos 7 e aos 14 dias após a instalação no germinador. Concluiu-se que o tratamento fitossanitário aumentou os espaçamentos falhos e múltiplos e reduziu os espaçamentos aceitáveis. O emprego de grafite reduziu os espaçamentos falhos e múltiplos e elevou os espaçamentos aceitáveis. A melhor forma de mistura do grafite ocorreu na máquina de tratamento fitossanitário de sementes. A distribuição longitudinal alcançou seu ponto ótimo com a dosagem de grafite de 3,37 g kg-1 de semente. As variáveis tratamento fitossanitário, mecanismo dosador e grafite não influíram na germinação das sementes de milho.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The soil contamination with petroleum is one of the major concern of industries operating in the field and also of environmental agencies. The petroleum consists mainly of alkanes and aromatic hydrocarbons. The most common examples of hydrocarbons polyaromatic are: naphthalene, anthracene, phenanthrene, benzopyrene and their various isomers. These substances cause adverse effects on human and the environment. Thus, the main objective of this work is to study the advanced oxidation process using the oxidant potassium permanganate (KMnO4) for remediation of soils contaminated with two polyaromatic hydrocarbons (PAHs): anthracene and phenanthrene. This study was conducted at bench scale, where the first stage was at batch experiment, using the variables: the time and oxidant dosage in the soil. The second stage was the remediation conducted in continous by a fix column, to this stage, the only variable was remediation time. The concentration of oxidant in this stage was based on the best result obtained in the tests at batch, 2,464 mg / L. The results of degradation these contaminants were satisfactory, at the following dosages and time: (a) 5g of oxidant per kg soil for 48 hours, it was obtained residual contaminants 28 mg phenanthrene and 1.25 mg anthracene per kg of soil and (b) for 7g of oxidant per kg soil in 48 hours remaining 24 mg phenanthrene and anthracene 0.77 mg per kg soil, and therefore below the intervention limit residential and industrial proposed by the State Company of Environmental Sao Paulo (CETESB)

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Originária da América do Sul, a ferrugem do eucalipto causada pelo fungo Puccinia psidii, vem se tornando uma doença limitante para a cultura do eucalipto no Brasil, exigindo a adoção de estratégias de controle, dentre as quais está o controle químico. Para avaliar eficiência e viabilidade econômica de fungicidas no controle da ferrugem do eucalipto, montou-se um ensaio a campo. Para a instalação do ensaio, utilizou-se o delineamento em blocos ao acaso, em esquema fatorial 3 x 3 (3 produtos e 3 doses), sendo 0,5, 1,0 e 1,5 mL ou g do produto comercial por litro de solução. Os tratamentos foram: 1-) Testemunha; 2-) Fungicida azoxistrobina (estrobilurina); 3-) Fungicida tebuconazol (triazol); 4-) Fungicida tebuconazol + trifloxistrobina (triazol + estrobilurina). O experimento constou de quatro repetições, com avaliação da severidade das plantas. As avaliações foram efetuadas com base no percentual de área foliar lesionada. Verificou-se que com o aumento na dosagem dos fungicidas, houve maior redução da doença nas plantas aos 7 e 15 dias pós-aplicação. O fungicida tebuconazol + trifloxistrobina a 1,5 mL/L foi o mais eficiente contra a ferrugem do eucalipto em condições de campo. O fungicida tebuconazol apresentou maior viabilidade econômica nas três doses testadas.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Nitrogen (N), besides being one of the macro more absorbed by plants, is the that most limits the production of sunflower. The aim of this study was to evaluate the nutrient content in leaves, grains and nutrient export due to nitrogen levels in sunflower cultivation. A randomized experimental block design consisting of five treatments and four replications: T1 - 50 kg N ha(-1) divided by 10, 20 and 20 kg ha(-1), T2 - 70 kg N ha(-1) divided by 10, 30 and 30 kg ha(-1); T3 - 90 kg N ha(-1) divided by 10, 40 and 40 kg ha(-1), T4 - 110 kg N ha(-1) divided by 10, 50 and 50 kg ha(-1), T5 - 130 kg N ha(-1) divided by 10, 60 and 60 kg ha(-1). These applications were made in installments when sowing and 34 and 48 days after sowing. The parameters were evaluated in leaf nutrient content, nutrient content in grains and nutrient export. Under the experimental conditions it was found that the optimum foliar N were purchased at a dosage above 110 kg ha-1 N. With the increasing amount of N supplied in the sunflower crop was exported over this element, but not at the same rate of increase in dosage. The lowest dose of N the lowest rates of export of P, K, Mg, S, B, Cu, Mn and Zn, while increasing the dose of this nutrient decreased the export of Ca.

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The objective of this scientific article is to introduce the opportunities of implementation of cleaner production (CP) in a shrimp culture farm. The methodology used for this was exploratory research implemented in a production unit located in the Northeast Brazil. The scientific article approaches since generic aspects of the technique about the management to use water, energy and the effluent characterization of this productive activity. It discusses quantitative aspects, environmental questions and chances of P+L during the productive process phases. The results points to input economy in the form of feed, soil correctives, medicines, and energy applied to the process, which range from 4% to 27%, emphasizing the small profit should be viewed as a source of considerable environment return. The authors conclude for the adoption property of this technique in this agribusiness segment, point out to the management importance of the input dosage in the quality of the final effluent, besides the adoption of a physical-chemistry remediation mechanism to the residual of Sodium metabissulphite used in the process of shrimp caught

Relevância:

10.00% 10.00%

Publicador:

Resumo:

This work aims to investigate the process of Dissolved air Flotation (DAF) for clarifying water samples with low turbidity using aluminum sulphate and Moringa oleifera seeds as coagulants. The experimental procedure was carried out in a bench scale flotation unit. The influences on the pre-treatment conditions (coagulant dosage and flocculation time) and flotation parameters (superficial application rate and recirculation rate) were evaluated considering the efficiency of the process. The efficiency was evaluated by determining the turbidity of the untreated and treated water samples. The results obtained showed that turbidity reduction can be obtained very efficiently by using DAF and the latter coagulant in low turbidity water. Using aluminum sulphate in pH´s 5.0 and 6.0 better efficiencies were obtained with low concentrations (15 mg/L), achieving values of 92% of turbidity reduction. In the case of use of Moringa oleifera better efficiencies of reduction of turbidity were reported when using a concentration of 50 mg/L in all range of pH´s, achieving 86% of reduction. The zeta potential was also determined, in an attempt to aid comprehension of the coagulation mechanisms involved. The coagulation mechanisms with Moringa oleifera seeds were shown to be adsorption and charge neutralization, as well as adsorption and bridging. Concerning aluminum sulphate, the predominant mechanisms are adsorption and charge neutralization and enmeshment in a precipitate. The results indicate that for low turbidity water, Moringa oleifera seeds could potentially be a viable substitute for aluminum sulphate

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The main objective of this research was the development and characterization of conventional and modified cationic asphalt emulsions. The asphalt emulsions were developed by using the Petroleum Asphalt Cement (CAP 50-70) from Fazenda Belém (Petrobras -Aracati-Ce). The first step in this research was the development of the oil phase (asphalt + solvent) and the aqueous phase (water + emulsifying agent + acid + additives), separately. During the experiments for the obtaining of the conventional asphalt emulsion, the concentration of each constituent was evaluated. For the obtaining of the oil phase, kerosene was used as solvent at 15 and 20 wt.%. For the development of the aqueous phase, the emulsifying agent was used at 0.3 and 3.0 wt.%, whereas the acid and the additive were set at 0.3 wt.%. The percentage of asphalt in the asphalt emulsion was varied in 50, 55, and 60 wt.% and the heating temperature was set at 120 °C. The aqueous phase in the asphalt emulsion was varied from 16.4 to 34.1 wt.% and the heating temperature was set at 60 °C. After the obtaining of the oil and the aqueous phases, they were added at a colloidal mill, remaining under constant stirring and heating during 15 minutes. Each asphalt emulsion was evaluated considering: sieve analysis, Saybolt Furol viscosity, pH determination, settlement and storage stability, residue by evaporation, and penetration of residue. After the characterization of conventional emulsions, it was chosen the one that presented all properties in accordance with Brazilian specifications (DNER-EM 369/97). This emulsion was used for the development of all modified asphalt emulsions. Three polymeric industrial residues were used as modifier agents: one from a clothing button industry (cutouts of clothing buttons) and two from a footwear industry (cutouts of sandals and tennis shoes soles), all industries located at Rio Grande do Norte State (Brazil).The polymeric residues were added into the asphalt emulsion (1 to 6 wt.%) and the same characterization rehearsals were accomplished. After characterization, it were developed the cold-mix asphalts. It was used the Marshall mix design. For cold-mix asphalt using the conventional emulsion, it was used 5, 6 and 7 wt.% asphalt emulsion. The conventional mixtures presented stability values according Brazilian specification (DNER-369/97). For mixtures containing asphalt modified emulsions, it was observed that the best results were obtained with emulsions modified by button residue

Relevância:

10.00% 10.00%

Publicador:

Resumo:

The disposal of sewage sludge is a growing problem face up to management of sanitary sevices. Otherwise, because its making process characteristic, the Ceramic Industry can tolerate the presence of this wastes as raw material. This study has as object to confirm the use of the sewage sluge in the Ceramic Industry like a sustentable alternative for its disposal. Futhermore, this study quests to evaluate the maximum proportion for incorporation of sludge wich result in technically and enviromentally suitable bricks. For found this proportion, the research consisted of (1) making of bricks in full scale, adde up 0%, 5%,10%, 15%, 20%, 25%,30%, 35% e 40% sludge, with size 220x105x45 mm, hand-molded by rammer and baked by industrial kiln; and (2) tecnical and enviromental evaluation of this bricks, according to Brazilian norms. The raw material uses were two distinct clays come from Goianinha/RN and sewage comes from a septic system tank and pumped into tank vehicle, of Natal/RN. The technical evaluation allowed to conclude the addiotion of the sludge brings about signifcant lost of mass and the water absorption grew up according to increase of sludge: every sludge-amended clay bricks absorved more water than control group. Thus, the compressive strength was signicantly decreased because the increase of sludge: bricks with 5% sludge added lost 45% of strength achieved at control group; the bricks made with 10 and 20% lost almost 70% of bigger strength. With up to 25% sludge added to the bricks, the streght decreased over 90%. Concerning heavy metal leaching, the two maximum proportion wich have tecnical approval, it means bricks sludge added with 15 and 20%, can say there is no risk of enviromental contamination using those bricks. This way, in this work context, it can to conclude the maximum proportion atends the technical and enviromental criterion is 20%

Relevância:

10.00% 10.00%

Publicador:

Resumo:

Eutrophication is a growing process present in the water sources located in the northeast of Brazil. Among the main consequences of these changes in trophic levels of a water source, stands out adding complexity to the treatment to achieve water standards. By these considerations, this study aimed to define, on a laboratory scale, products and operational conditions to be applied in the processing steps using raw water from Gargalheiras dam, RN, Brazil. The dam mentioned shows a high number of cyanobacteria, with a concentration of cells / ml higher than that established by Decree No. 518/04 MS. The same source was also considered by the state environmental agency in 2009 as hypereutrophic. The static tests developed in this research simulated direct filtration (laboratory filters) and pre-oxidation with chlorine and powdered activated carbon adsorption. The research included the evaluation of the coagulants aluminum hydrochloride (HCA) and alum (SA). The development of the research investigated the conditions for rapid mixing, the dosages of coagulants and pHs of coagulation by the drawing of diagrams. The interference of filtration rate and particle size of filtering means were evaluated as samples and the time of contact were tested with chlorine and activated carbon. By the results of the characterization of the raw water source it was possible to identify the presence of a high pH (7.34). The true color was significant (29 uH) in relation to the apparent color and turbidity (66 uH and 13.60 NTU), reflecting in the measurement of organic matter: MON (8.41 mg.L-1) and Abs254 (0.065 cm-1). The optimization of quick mix set time of 17", the speed gradient of 700 s-1 in the coagulation with HCA and the time of 20" with speed gradient of 800 s-1 for SA. The smaller particle sizes of sand filtering means helped the treatment and the variation in filtration rate did not affect significantly the efficiency of the process. The evaluation of the processing steps found adjustment in standard color and turbidity of the Decree nº 518/04 MS, taking in consideration the average values found in raw water. In the treatment using the HCA for direct filtration the palatable pattern based on the apparent color can be achieved with a dose of 25 mg L-1. With the addition of pre-oxidation step, the standard result was achieved with a reduced dose for 12 mgHCA.L-1. The turbidity standard for water was obtained by direct filtration when the dose exceeds 25 mg L-1 of HCA. With pre-oxidation step there is the possibility of reducing the dose to 20 mg L-1.The addition of CAP adsorption, promoted drinking water for both parameters, with even lower dosage, 13 mg L-1 of HCA. With coagulation using SA removal required for the parameter of apparent color it was achieved with pre-oxidation and 22 mgSA.L-1. Despite the satisfactory results of treatment with the alum, it was not possible to provide water with turbidity less than 1.00 NTU even with the use of all stages of treatment