Polybridge Technical Report

This study examined the physical and chemical properties of a novel, fully-recirculated prawn and polychaete production system that incorporated polychaete-assisted sand filters (PASF). The aims were to assess and demonstrate the potential of this system for industrialisation, and to provide optimisations for wastewater treatment by PASF. Two successive seasons were studied at commercially-relevant scales in a prototype system constructed at the Bribie Island Research Centre in Southeast Queensland. The project produced over 5.4 tonnes of high quality black tiger prawns at rates up to 9.9 tonnes per hectare, with feed conversion of up to 1.1. Additionally, the project produced about 930 kg of high value polychaete biomass at rates up to 1.5 kg per square metre of PASF, with the worms feeding predominantly on waste nutrients. Importantly, this closed production system demonstrated rapid growth of healthy prawns at commercially relevant production levels, using methods that appear feasible for application at large scale. Deeper (23 cm) PASF beds provided similar but more reliable wastewater treatment efficacies compared with shallower (13 cm) beds, but did not demonstrate significantly greater polychaete productivity than (easier to harvest) shallow beds. The nutrient dynamics associated with seasonal and tidal operations of the system were studied in detail, providing technical and practical insights into how PASF could be optimised for the mitigation of nutrient discharge. The study also highlighted some of the other important advantages of this integrated system, including low sludge production, no water discharge during the culture phase, high ecosystem health, good prospects for biosecurity controls, and the sustainable production of a fishery-limited resource (polychaetes) that may be essential for the expansion of prawn farming industries throughout the world. Regarding nutrient discharge from this prototype mariculture system, when PASF was operating correctly it proved feasible to have no water (or nutrient) discharge during the entire prawn growing season. However, the final drain harvest and emptying of ponds that is necessary at the end of the prawn farming season released 58.4 kg ha-1 of nitrogen and 6 kg ha-1 of phosphorus (in Season 2). Whilst this is well below (i.e., one-third to one-half of) the current load-based licencing conditions for many prawn farms in Australia, the levels of nitrogen and chlorophyll a in the ponds remained higher than the more-stringent maximum limits at the Bribie Island study site. Zero-net-nutrient discharge was not achieved, but waste nutrients were low where 5.91 kg of nitrogen and 0.61 kg of phosphorus was discharged per tonne of prawns produced. This was from a system that deployed PASF at 14.4% of total ponded farm area which treated an average of 5.8% of pond water daily and did not use settlement ponds or other natural or artificial water remediation systems. Four supplemental appendices complement this research by studying several additional aspects that are central to the industrialisation of PASF. The first details an economic model and decision tool which allows potential users to interactively assess construction and operational variables of PASF at different scales. The second provides the qualitative results of a prawn maturation trial conducted collaboratively with the Commonwealth Scientific and Industrial Research Organisation (CSIRO) to assess dietary inclusions of PASF-produced worms. The third provides the reproductive results from industry-based assessments of prawn broodstock produced using PASF. And the fourth appendix provides detailed elemental and nutritional analyses of bacterial biofilm produced by PASF and assesses its potential to improve the growth of prawns in recirculated culture systems.

Construction of a cDNA clone for a nuclear-coded subunit of cytochrome c oxidase from rat liver

A cDNA library for 6S–9S poly(A)-containing RNA from rat liver was constructed in Image . Initial screening of the clones was carried out using single stranded 32P-labeled cDNA prepared against poly(A)-containing RNA isolated from immunoadsorbed polyribosomes enriched for the nuclear-coded subunit messenger RNAs of cytochrome c oxidase. One of the clones, pCO89, was found to hybridize with the messenger RNA for subunit VIC. The DNA sequence of the insert in pCO89 was carried out and it has got extensive homology with the C-terminal 33 amino acids of subunit VIC from beef heart cytochrome c oxidase. In addition, the insert contained 146 bp, corresponding to a portion of the 3′-non-coding region. Northern blot analysis of rat liver RNA with the nick-translated insert of pCO89 revealed that the messenger RNA for subunit VI would contain around 510 bases.

Following fashion: Visible progressiveness and the social construction of firm value

A central tenet underlying studies on management fashions is that the diffusion of novel forms, models and techniques is driven by an institutional norm of progress, which is the societal expectation that managers will continuously use 'new and improved' management practices. We add to the literature on management fashions by arguing that, if the display of progressiveness in the manner of managing and organizing is expected of organizations, firms that are visibly progressive would be evaluated more positively by organizational audiences following this institutional prescription. Using article counts of co-occurrences of firms and various fashionable management practices in Wall Street Journal, we hypothesize positive effects of such associations on security analysts' evaluations of these firms. Results support this hypothesis. Our study enriches the management fashion literature by highlighting the consequential relevance of organizational adherence to the norm of progress.

Construction of stability multipliers for non-linear feedback systems

This paper is concerned with the analysis of the absolute stability of a non-linear autonomous system which consists of a single non-linearity belonging to a particular class, in an otherwise linear feedback loop. It is motivated from the earlier Popovlike frequency-domain criteria using the ' multiplier ' eoncept and involves the construction of ' stability multipliers' with prescribed phase characteristics. A few computer-based methods by which this problem can be solved are indicated and it is shown that this constitutes a stop-by-step procedure for testing the stability properties of a given system.

The construction of feminism in Indonesian film: Arisan 2!

Feminism in Indonesian society is related to the emancipation term that women nowadays have still been bringing up this issue. However, Arisan 2! film showed a shift in film discourse regarding the representation of cosmopolitan women in Indonesia. This research examines on how Arisan 2! film as a media portrays feminism in the society of Jakarta. Feminism in Arisan 2! film was likely to expose the liberal feminism in nowadays modern society through several issues of women’s emancipation, specifically in the areas of marriage, job, and social life.

Safety impacts of alcohol and other drugs in construction

Estimated 638,400 persons suffered a work-related injury or illness in 2009-2010 and 337 lost their lives as a result in 2009-2010. In 2013-2014, there were 186 fatalities with 29 (16%) occurring in construction. Very little is known about what proportion of accidents are directly attributable to the effects of AOD. Anecdotal evidence highlights issues of AOD and its association with safety risk on construction sites. Research Objective: • To scientifically evaluate the relationship between the use of AOD and the safety impacts within the Australian construction industry to engender a cultural change in the workforce • A nationally consistent and collaborative approach involving government, employers and employees, unions and other key industry stakeholders

Essays on Finnish Economic Growth and Productivity, 1860-2005

This study examines Finnish economic growth. The key driver of economic growth was productivity. And the major engine of productivity growth was technology, especially the general purpose technologies (GPTs) electricity and ICT. A new GPT builds on previous knowledge, yet often in an uncertain, punctuated, fashion. Economic history, as well as the Finnish data analyzed in this study, teaches that growth is not a smooth process but is subject to episodes of sharp acceleration and deceleration which are associated with the arrival, diffusion and exhaustion of new general purpose technologies. These are technologies that affect the whole economy by transforming both household life and the ways in which firms conduct business. The findings of previous research, that Finnish economic growth exhibited late industrialisation and significant structural changes were corroborated by this study. Yet, it was not solely a story of manufacturing and structural change was more the effect of than the cause for economic growth. We offered an empirical resolution to the Artto-Pohjola paradox as we showed that a high rate of return on capital was combined with low capital productivity growth. This result is important in understanding Finnish economic growth 1975-90. The main contribution of this thesis was the growth accounting results on the impact of ICT on growth and productivity, as well as the comparison of electricity and ICT. It was shown that ICT s contribution to GDP growth was almost twice as large as electricity s contribution over comparable periods of time. Finland has thus been far more successful as an ICT producer than a producer of electricity. Unfortunately in the use of ICT the results were still more modest than for electricity. During the end of the period considered in this thesis, Finland switched from resource-based to ICT-based growth. However, given the large dependency on the ICT-producing sector, the ongoing outsourcing of ICT production to low wage countries provides a threat to productivity performance in the future. For a developed country only change is constant and history teaches us that it is likely that Finland is obliged to reorganize its economy once again in the digital era.

The construction of a taxonomy of early childhood educators’ work

Despite considerable research on the impact of early childhood education (ECE), there is little empirical evidence about what the everyday work of educators entails. This paper reports on the development of a tool to capture generalisable data on the everyday work of educators so as to inform effective workforce policy. This tool—a taxonomy of early childhood educators’ work—was developed by drawing on the expertise of six early years’ experts from Australia and the United States of America (USA) and includes time-use diaries, focus groups and interviews with 21 early childhood educators working in long day care and preschool services. The taxonomy, which we present here, consists of 10 domains, each with a number of sub-classes. We propose that this taxonomy is a useful codification system for ascertaining the everyday work tasks, activities and actions of early childhood educators in diverse early years’ settings. It is anticipated that the taxonomy will prove a valuable tool for subsequent research investigating the early childhood workforce.

The role of productivity in the ecological and evolutionary dynamics of predator-prey interaction

Productivity is predicted to drive the ecological and evolutionary dynamics of predator-prey interaction through changes in resource allocation between different traits. However, resources are seldom constantly available and thus temporal variation in productivity could have considerable effect on the species' potential to evolve. To study this, three long-term microbial laboratory experiments were established where Serratia marcescens prey bacteria was exposed to predation of protist Tetrahymena thermophila in different prey resource environments. The consequences of prey resource availability for the ecological properties of the predator-prey system, such as trophic dynamics, stability, and virulence, were determined. The evolutionary changes in species traits and prey genetic diversity were measured. The prey defence evolved stronger in high productivity environment. Increased allocation to defence incurred cost in terms of reduced prey resource use ability, which probably constrained prey evolution by increasing the effect of resource competition. However, the magnitude of this trade-off diminished when measured in high resource concentrations. Predation selected for white, non-pigmented, highly defensive prey clones that produced predation resistant biofilm. The biofilm defence was also potentially accompanied with cytotoxicity for predators and could have been traded off with high motility. Evidence for the evolution of predators was also found in one experiment suggesting that co-evolutionary dynamics could affect the evolution and ecology of predator-prey interaction. Temporal variation in resource availability increased variation in predator densities leading to temporally fluctuating selection for prey defences and resource use ability. Temporal variation in resource availability was also able to constrain prey evolution when the allocation to defence incurred high cost. However, when the magnitude of prey trade-off was small and the resource turnover was periodically high, temporal variation facilitated the formation of predator resistant biofilm. The evolution of prey defence constrained the transfer of energy from basal to higher trophic levels, decreasing the strength of top-down regulation on prey community. Predation and temporal variation in productivity decreased the stability of populations and prey traits in general. However, predation-induced destabilization was less pronounced in the high productivity environment where the evolution of prey defence was stronger. In addition, evolution of prey defence weakened the environmental variation induced destabilization of predator population dynamics. Moreover, protozoan predation decreased the S. marcescens virulence in the insect host moth (Parasemia plantaginis) suggesting that species interactions outside the context of host-pathogen relationship could be important indirect drivers for the evolution of pathogenesis. This thesis demonstrates that rapid evolution can affect various ecological properties of predator-prey interaction. The effect of evolution on the ecological dynamics depended on the productivity of the environment, being most evident in the constant environments with high productivity.

Construction of inverses with prescribed zero minors and applications to decentralized stabilization

We examine the following question: Suppose R is a principal ideal domain, and that F is an n × m matrix with elements in R, with n>m. When does there exist an m × n matrix G such that GF = Im, and such that certain prescribed minors of G equal zero? We show that there is a simple necessary condition for the existence of such a G, but that this condition is not sufficient in general. However, if the set of minors of G that are required to be zero has a certain pattern, then the condition is necessary as well as sufficient. We then show that the pattern mentioned above arises naturally in connection with the question of the existence of decentralized stabilizing controllers for a given plant. Hence our result allows us to derive an extremely simple proof of the fact that a necessary and sufficient condition for the existence of decentralized stabilizing controllers is the absence of unstable decentralized fixed modes, as well as to derive a very clean expression for these fixed modes. In addition to the application to decentralized stabilization, we believe that the result is of independent interest.

Acoustic emission source location in composite structure by Voronoi construction using geodesic curve evolution

Conventional analytical/numerical methods employing triangulation technique are suitable for locating acoustic emission (AE) source in a planar structure without structural discontinuities. But these methods cannot be extended to structures with complicated geometry, and, also, the problem gets compounded if the material of the structure is anisotropic warranting complex analytical velocity models. A geodesic approach using Voronoi construction is proposed in this work to locate the AE source in a composite structure. The approach is based on the fact that the wave takes minimum energy path to travel from the source to any other point in the connected domain. The geodesics are computed on the meshed surface of the structure using graph theory based on Dijkstra's algorithm. By propagating the waves in reverse virtually from these sensors along the geodesic path and by locating the first intersection point of these waves, one can get the AE source location. In this work, the geodesic approach is shown more suitable for a practicable source location solution in a composite structure with arbitrary surface containing finite discontinuities. Experiments have been conducted on composite plate specimens of simple and complex geometry to validate this method.

Knowledge management research in the construction industry: a review

Purpose: Knowledge management (KM) is important to the knowledge-intensive construction industry. The diversified and changing nature of works in this field warrants us to stocktake, identify changes and map out KM research framework for future exploration. Design/methodology/approach: The study involves three aspects. First, three stages of KM research in construction were distinguished in terms of the time distribution of 217 target publications. Major topics in the stages were extracted for understanding the changes of research emphasis from evolutionary perspective. Second, the past works were summed up in a three-dimensional research framework in terms of management organization, managerial methodology and approach, and managerial objective. Finally, potential research orientations in the future were predicted to expand the existing research framework. Findings: It was found that (1) KM research has significantly blossomed in the last two decades with a great potential; (2) major topics of KM were changing in terms of technology, technique, organization, attribute of knowledge and research objectives; (3) past KM studies centred around management organization, managerial methodology and approach, and managerial objective thus a three-dimensional research framework was proposed; (4) within the research framework, team-level, project-level and firm-level KM were studied to achieve project, organizational and competitive objectives by integrated methodologies of information technology, social technique and KM process tool; and (5) nine potential research orientations were predicted corresponding to the three dimensions. Finally, an expanded research framework was proposed to encourage and guide future research works in this field. Research limitations/implications: The paper only focused on the construction industry. The findings need further exploration in order to discover any possible missing important research works which were not published in English or not included in the time period. Originality/value: The paper formed a systematic framework of KM research in construction and predicted the potential research orientations. It provides much value for the researchers who want to understand the past and the future of global KM research in the construction industry.

Supporting knowledge-intensive construction management tasks in BIM

The delivery of products and services for construction-based businesses is increasingly becoming knowledge-driven and information-intensive. The proliferation of building information modelling (BIM) has increased business opportunities as well as introduced new challenges for the architectural, engineering and construction and facilities management (AEC/FM) industry. As such, the effective use, sharing and exchange of building life cycle information and knowledge management in building design, construction, maintenance and operation assumes a position of paramount importance. This paper identifies a subset of construction management (CM) relevant knowledge for different design conditions of building components through a critical, comprehensive review of synthesized literature and other information gathering and knowledge acquisition techniques. It then explores how such domain knowledge can be formalized as ontologies and, subsequently, a query vocabulary in order to equip BIM users with the capacity to query digital models of a building for the retrieval of useful and relevant domain-specific information. The formalized construction knowledge is validated through interviews with domain experts in relation to four case study projects. Additionally, retrospective analyses of several design conditions are used to demonstrate the soundness (realism), completeness, and appeal of the knowledge base and query-based reasoning approach in relation to the state-of-the-art tools, Solibri Model Checker and Navisworks. The knowledge engineering process and the methods applied in this research for information representation and retrieval could provide useful mechanisms to leverage BIM in support of a number of knowledge intensive CM/FM tasks and functions.

Tuning the beta-turn segment in designed peptide beta-hairpins: Construction of a stable type I ' beta-turn nucleus and hairpin-helix transition promoting segments

Designed octapeptides Boc-Leu-Val-Val-Aib-(D)Xxx-Leu- Val-Val-OMe ((D)Xxx = (D)Ala, 3a; (D)Val, 3c and (D)Pro, 5a) and Boc-Leu-Phe-Val-Aib-DAla-Leu-Phe-Val-OMe (3b) have been investigated to construct models of a stable type I' beta-turn nucleated hairpin and to generate systems for investigating helix-hairpin conformational transitions. Peptide 5a, which contains a central Aib-(D)Pro segment, is shown to adopt a stable type I' beta-turn nucleated hairpin structure, stabilized by four cross-strand hydrogen bonds. The stability of the structure in diverse solvents is established by the observation of all diagnostic NOEs expected in a beta-hairpin conformation. Replacement of (D)Pro5 by (D)Ala/(D)Val (3a-c) results in sequences that form beta-hairpins in hydrogen bonding solvents like CD3OH and DMSO-d(6). However, in CDCl3 evidence for population of helical conformations is obtained. Peptide 6b (Boc-Leu-Phe-Val-Aib-Aib-Leu-Phe-Val-OMe), which contains a centrally positioned Aib-Aib segment, provides a clear example of a system, which exhibits a helical conformation in CDCl3 and a significant population of both helices and hairpins in CD3OH and DMSO-d(6). The coexistence of multiple conformations is established by the simultaneous observation of diagnostic NOEs. Control over stereochemistry of the central beta-turn permits generation of models for robust beta-hairpins and also for the construction of systems that may be used to probe helix-hairpin conformational transitions. (c) 2006 Wiley Periodicals, Inc.