Nitrogen removal and sustainability of vertical flow constructed wetlands for small scale wastewater treatment

The challenge for wastewater professionals is to design and operate treatment processes that support human well being and are environmentally sensitive throughout the life-cycle. This research focuses on one technology for small-scale wastewater treatment: the vertical flow constructed wetland (VFCW), which is herein investigated for the capacity to remove ammonium and nitrate nitrogen from wastewater. Hydraulic regime and presence/absence of vegetation are the basis for a three-phase bench scale experiment to determine oxygen transfer and nitrogen fate in VFCWs. Results show that 90% NH4+-N removal is achieved in aerobic downflow columns, 60% NO3--N removal occurs in anaerobic upflow columns, and 60% removal of total nitrogen can be achieved in downflow-upflow in-series. The experimental results are studied further using a variably saturated flow and reactive transport model, which allows a mechanistic explanation of the fate and transport of oxygen and nitrogen. The model clarifies the mechanisms of oxygen transport and nitrogen consumption, and clarifies the need for readily biodegradable COD for denitrification. A VFCW is then compared to a horizontal flow constructed wetland (HFCW) for life cycle environmental impacts. High areal emissions of greenhouse gases from VFCWs compared to HFCWs are the driver for the study. The assessment shows that because a VFCW is only 25% of the volume of an HFCW designed for the same treatment quality, the VFCW has only 25-30% of HFCW impacts over 12 impact categories and 3 damage categories. Results show that impacts could be reduced by design improvements. Design recommendations are downflow wetlands for nitrification, upflow wetlands for denitrification, series wetlands for total nitrogen removal, hydraulic load of 142 L/m2d, 30 cm downflow wetland depth, 1.0 m upflow wetland depth, recycle, vegetation and medium-grained sand. These improvements will optimize nitrogen removal, minimize gaseous emissions, and reduce wetland material requirements, thus reducing environmental impact without sacrificing wastewater treatment quality.

Influence of Vegetation Removal and Altering Water Levels on CO2 Flux Rates of a Northern Bog

Boreal peatlands contain approximately one third of the global soil carbon and are considered net sinks of atmospheric CO2. Water level position is one of the main regulators of CO2 fluxes in northern peatlands because it controls both the thickness of the aerobic layer in peat and plant communities. However, little is known about the role of different plant functional groups and their possible interaction with changing water level in boreal peatlands with regard to CO2 cycling. Climate change may also accelerate changes in hydrological conditions, changing both aerobic conditions and plant communities. To help answer these questions, this study was conducted at a mesocosm facility in Northern Michigan where the aim was to experimentally study the effects of water levels, plant functional groups (sedges, shrubs and mosses) and the possible interaction of these on the CO2 cycle of a boreal peatland ecosystem. The results indicate that Ericaceous shrubs are important in the boreal peatland CO2 cycle. The removal of these plants decreased ecosystem respiration, gross ecosystem production and net ecosystem exchange rates, whereas removing sedges did not show any significant differences in the flux rates. The water level did not significantly affect the flux rates. The amount of aboveground sedge biomass was higher in the low water level sedge treatment plots compared to the high water level sedge plots, possibly because the lowered water level and the removal of Ericaceae released nutrients for sedges to use up.

Long-term assessment of wild boar harvesting and cattle removal for bovine tuberculosis control in free ranging populations

Wild boar is a recognized reservoir of bovine tuberculosis (TB) in the Mediterranean ecosystems, but information is scarce outside of hotspots in southern Spain. We describe the first high-prevalence focus of TB in a non-managed wild boar population in northern Spain and the result of eight years of TB management. Measures implemented for disease control included the control of the local wild boar population through culling and stamping out of a sympatric infected cattle herd. Post-mortem inspection for detection of tuberculosis-like lesions as well as cultures from selected head and cervical lymph nodes was done in 745 wild boar, 355 Iberian ibexes and five cattle between 2004 and 2012. The seasonal prevalence of TB reached 70% amongst adult wild boar and ten different spoligotypes and 13 MIRU-VNTR profiles were detected, although more than half of the isolates were included in the same clonal complex. Only 11% of infected boars had generalized lesions. None of the ibexes were affected, supporting their irrelevance in the epidemiology of TB. An infected cattle herd grazed the zone where 168 of the 197 infected boars were harvested. Cattle removal and wild boar culling together contributed to a decrease in TB prevalence. The need for holistic, sustained over time, intensive and adapted TB control strategies taking into account the multi-host nature of the disease is highlighted. The potential risk for tuberculosis emergence in wildlife scenarios where the risk is assumed to be low should be addressed.

A comparative study of alginate beads and an ion-exchange resin for the removal of heavy metals from a metal plating effluent

The capacity of dry protonated calcium alginate beads to sorb metals from an industrial effluent was studied and compared with a commercial ion-exchange resin (Lewatit TP 207). Both sorbents decreased zinc, nickel, iron and calcium concentrations in the effluent, and released sodium during treatment. Alginate beads removed lower amounts of heavy metals than the resin, but exhibited faster uptake kinetics. Zinc desorption from the sorbents was achieved in 30 minutes using 0.1 M HCl or 0.1 M H(2)SO(4). Desorption ratios with these acids varied between 90 and 100% for alginate, and 98 to 100% for the ion-exchange resin. Reusability tests with HCl showed that alginate beads can stand acid desorption and recover binding capacity. Overall, the comparison of dry protonated alginate beads with the resin supports the potential of the biosorbent for the treatment of industrial effluents.

Efficient removal of paracetamol using LaCu1-xMxO3 (M=Mn, Ti) perovskites as heterogeneous Fenton-like catalysts

A series of perovskite-like oxides LaCu1-xMxO3 (M=Mn, Ti; 0.0 ⩽ x ⩽ 0.8) was prepared by amorphous citrate decomposition and characterized by XRD, ICP-OES and XPS techniques. The catalysts were tested in the Fenton-like degradation of paracetamol with H2O2, under mild reaction conditions, 25 °C and nearly neutral pH. Values of decomposition of paracetamol between 80 and 97% at 300 min were achieved for most of samples. The presence of the Cu2+/Cu+ pair at the surface of the catalysts is necessary to carry out the reaction and the catalysts containing higher amount of copper at the surface, resulted to be more active. The leaching of metals was less than 1%, which discards the contribution of the homogenous Fenton-like reaction and remarks the high stability of the metals into the mixed oxide network. The catalytic activity of LaCu0.8Mn0.2O3 was maintained after three cycles of reaction, which proves the stability and reusability of the catalyst.

Activated Carbons Produced from Mixtures of Synthetic Polymers by Physical and Chemical Activation: Application on MCPA Removal

The production of AC was achieved using the most common industrial and consumer solid waste, namely PET, alone or blended with other synthetic polymer such PAN. The PET-PAN mixture (1:1 W/W %) was subjected to carbonization, with a pyrolysis yield off 31.9%, between that obtained with PET (16.9%) or PAN (42.6%) separately. By mixing PET, as a raw material, with PAN (different ratio), an improvement in the final yield of the AC production, for the same activation time, with CO2, was found.

Activated Carbons Produced from Mixtures of Synthetic Polymers by Physical and Chemical Activation: Application on MCPA Removal

The production of AC was achieved using the most common industrial and consumer solid waste, namely PET, alone or blended with other synthetic polymer such PAN. The PET-PAN mixture (1:1 W/W %) was subjected to carbonization, with a pyrolysis yield off 31.9%, between that obtained with PET (16.9%) or PAN (42.6%) separately. By mixing PET, as a raw material, with PAN (different ratio), an improvement in the final yield of the AC production, for the same activation time, with CO2, was found.

Preparation and Characterization of Polymeric Beads and Membranes for Boron Removal From Water

Boron is an element essential for various biological processes, nevertheless at high concentration it can cause health issues in both plants and animals, thus making boron a pollutant element. Low cost and effective polymeric adsorbents capable of removing boron in aqueous solution at neutral pH were prepared for this purpose. The adsorbent selectivity towards boron was conferred taking advantage of the interaction between boric acid and the alcoholic groups of N-methyl-D-Glucamine, which are able to form specific complexes. Two different kinds of devices were produced and tested: cross-linked chitosan hydrogel beads (CCBMG) and PVA/chitosan membranes, the latter taking advantage of scCO2-assisted phase inversion technique. The capability of the adsorbents to be regenerated and to allow recovery of boric acid from a solution emulating the concentration of boric acid in seawater were evaluated.

Multi-organ support device for combined extracorporeal carbon dioxide removal and hemofiltration treatments with pump-free solution for ultrafiltration

The use of extracorporeal organ support (ECOS) devices is increasingly widespread, to temporarily sustain or replace the functions of impaired organs in critically ill patients. Among ECOS, respiratory functions are supplied by extracorporeal life support (ECLS) therapies like extracorporeal membrane oxygenation (ECMO) and extracorporeal carbon dioxide removal (ECCO2R), and renal replacement therapies (RRT) are used to support kidney functions. However, the leading cause of mortality in critically ill patients is multi-organ dysfunction syndrome (MODS), which requires a complex therapeutic strategy where extracorporeal treatments are often integrated to pharmacological approach. Recently, the concept of multi-organ support therapy (MOST) has been introduced, and several forms of isolated ECOS devices are sequentially connected to provide simultaneous support to different organ systems. The future of critical illness goes towards the development of extracorporeal devices offering multiple organ support therapies on demand by a single hardware platform, where treatment lines can be used alternately or in conjunction. The aim of this industrial PhD project is to design and validate a device for multi-organ support, developing an auxiliary line for renal replacement therapy (hemofiltration) to be integrated on a platform for ECCO2R. The intended purpose of the ancillary line, which can be connected on demand, is to remove excess fluids by ultrafiltration and achieve volume control by the infusion of a replacement solution, as patients undergoing respiratory support are particularly prone to develop fluid overload. Furthermore, an ultrafiltration regulation system shall be developed using a powered and software-modulated pinch-valve on the effluent line of the hemofilter, proposed as an alternative to the state-of-the-art solution with peristaltic pump.

Contaminants of emerging concern in drinking water: assessment of the effectiveness of removal by drinking water treatments and possible risks to human health

Contaminants of emerging concern are increasingly detected in the water cycle, with endocrine-disrupting chemicals (EDCs) receiving attention due to their potential to cause adverse health effects even at low concentrations. Although the EU has recently introduced some EDCs into drinking water legislation, most drinking water treatment plants (DWTPs) are not designed to remove EDCs, making their detection and removal in DWTPs an important challenge. The aim of this doctoral project was to investigate hormones and phenolic compounds as suspected EDCs in drinking waters across the Romagna area (Italy). The main objectives were to assess the occurrence of considered contaminants in source and drinking water from three DWTPs, characterize the effectiveness of removal by different water treatment processes, and evaluate the potential biological impact on drinking water and human health. Specifically, a complementary approach of target chemical analysis and effect-based methods was adopted to explore drinking water quality, treatment efficacy, and biological potential. This study found that nonylphenol (NP) was prevalent in all samples, followed by BPA. Sporadic contamination of hormones was found only in source waters. Although the measured EDC concentrations in drinking water did not exceed threshold guideline values, the potential role of DWTPs as an additional source of EDC contamination should be considered. Significant increases in BPA and NP levels were observed during water treatment steps, which were also reflected in estrogenic and mutagenic responses in water samples after the ultrafiltration. This highlights the need to monitor water quality during various treatment processes to improve the efficiency of DWTPs. Biological assessments on finished water did not reveal any bioactivity, except for few treated water samples that exhibited estrogenic responses. Overall, the data emphasize the high quality of produced drinking water and the value of applying integrated chemical analysis and in vitro bioassays for water quality assessment.

Toxic cyanobacteria in water intended for drinking purpose: improvement of cells and toxins’ analyses and of treatments for their removal

Massive proliferations of cyanobacteria in freshwaters have recently increased, causing ecological and economic losses. Their ever-increasing presence in water sources destined to potabilization has become a major threat for public health, since several species can produce harmful toxins (cyanotoxin). Therefore, additional specific measures to improve management and treatment of drinking water(s) are required. The PhD thesis investigates toxic cyanobacteria in drinking waters with a special focus on Emilia-Romagna (Italy), throughout three separated chapters, each with different specific objectives. The first chapter aims at improving the fast monitoring of cyanobacteria in drinking water, which was investigated by testing different models of multi-wavelength spectrofluorometers. Inter-laboratories calibrations were conducted using mono-specific cultures and field samples, and both the feasibility and the technical limitations of such tools were illustrated. The second chapter evaluates the effectiveness of drinking water treatments in removing cyanobacterial cells and toxins. Two chlorinated oxidants (sodium hypochlorite and chlorine dioxide) already in use for pre-oxidation during water potabilization, were tested on cultures of the toxic cyanobacterium Microcystis aeruginosa posing a specific focus on toxin removal and revealing that pre-oxidation can cause the release of toxins and unknown metabolites. Innovative treatments based on non-thermal plasma were also tested, observing an effective and rapid inactivation of cyanobacterial cells. The third chapter presents a study on a cyanobacterium isolated from a drinking water reservoir of Emilia-Romagna and investigated by combining biological, chemical, and genomic methods. Although the strain did not produce any known cyanotoxin, high toxicity of water-extract was observed in bioassays and potential implications for drinking water were discussed. Overall, the PhD thesis offers new insights into toxic cyanobacteria management in drinking water, highlighting best practices for drinking water managers regarding their detection and removal. Additionally, the thesis provides new contributions to the understanding of the freshwater cyanobacteria community in the Emilia-Romagna region.

Solvent regeneration of activated carbon mixed-matrix membranes for the removal of micropollutants from wastewater

The constantly increasing demand of clean water has become challenging to deal with over the past years, water being an ever more precious resource. In recent times, the existing wastewater treatments had to be integrated with new steps, due to the detection of so-called organic micropollutants (OMPs). These compounds have been shown to adversely affect the environment and possibly human health, even when found in very low concentrations. In order to remove OMPs from wastewater, one possible technique is a hybrid process combining filtration and adsorption. In this work, polyethersulfone multi-channel mixed-matrix membranes with embedded powdered activated carbon (PAC) were tested to investigate the membrane’s adsorption and desorption performance. Micropollutants retention was analyzed using the pharmaceutical compounds diclofenac (DCF), paracetamol (PARA) and carbamazepine (CBZ) in filtration mode, combining the PAC adsorption process with the membrane’s ultrafiltration. Desorption performance was studied through solvent regeneration, using seven different solvents: pure water, pure ethanol, mixture of ethanol and water in different concentration, sodium hydroxide and a mixture of ethanol and sodium hydroxide. Regeneration experiments were carried out in forward-flushing. At first regeneration efficiency was investigated using a single-solute solution (diclofenac in water). The mixture Ethanol/Water (50:50) was found to be the most efficient with long-term retention of 59% after one desorption cycle. It was, therefore, later tested on a membrane previously loaded with a multi-solute solution. Three desorption cycles were performed after which, retention (after 30 min) reached values of 87% for PARA and 72% for CBZ and 55% for DCF, which indicates decent regenerability. A morphological analysis on the membranes confirmed that, in any case, the regeneration cycles did not affect either the membranes’ structure, or the content and distribution of PAC in the matrix.

Thermodynamic Study Of The Micellization Of Zwitterionic Surfactants And Their Interaction With Polymers In Water By Isothermal Titration Calorimetry.

The micellization of a homologous series of zwitterionic surfactants, a group of sulfobetaines, was studied using isothermal titration calorimetry (ITC) in the temperature range from 15 to 65 °C. The increase in both temperature and the alkyl chain length leads to more negative values of ΔGmic(0) , favoring the micellization. The entropic term (ΔSmic(0)) is predominant at lower temperatures, and above ca. 55-65 °C, the enthalpic term (ΔHmic(0)) becomes prevalent, figuring a jointly driven process as the temperature increases. The interaction of these sulfobetaines with different polymers was also studied by ITC. Among the polymers studied, only two induced the formation of micellar aggregates at lower surfactant concentration: poly(acrylic acid), PAA, probably due to the formation of hydrogen bonds between the carboxylic group of the polymer and the sulfonate group of the surfactant, and poly(sodium 4-styrenesulfonate), PSS, probably due to the incorporation of the hydrophobic styrene group into the micelles. The prevalence of the hydrophobic and not the electrostatic contributions to the interaction between sulfobetaine and PSS was confirmed by an increased interaction enthalpy in the presence of electrolytes (NaCl) and by the observation of a significant temperature dependence, the latter consistent with the proposed removal of hydrophobic groups from water.

Long-term Postoperative Atrophy Of Contralateral Hippocampus And Cognitive Function In Unilateral Refractory Mtle With Unilateral Hippocampal Sclerosis.

This study aimed to evaluate long-term atrophy in contralateral hippocampal volume after surgery for unilateral MTLE, as well as the cognitive outcome for patients submitted to either selective transsylvian amygdalohippocampectomy (SelAH) or anterior temporal lobe resection (ATL). We performed a longitudinal study of 47 patients with MRI signs of unilateral hippocampal sclerosis (23 patients with right-sided hippocampal sclerosis) who underwent surgical treatment for MTLE. They underwent preoperative/postoperative high-resolution MRI as well as neuropsychological assessment for memory and estimated IQ. To investigate possible changes in the contralateral hippocampus of patients, we included 28 controls who underwent two MRIs at long-term intervals. The volumetry using preoperative MRI showed significant hippocampal atrophy ipsilateral to the side of surgery when compared with controls (p<0.0001) but no differences in contralateral hippocampal volumes. The mean postoperative follow-up was 8.7 years (± 2.5 SD; median=8.0). Our patients were classified as Engel I (80%), Engel II (18.2%), and Engel III (1.8%). We observed a small but significant reduction in the contralateral hippocampus of patients but no volume changes in controls. Most of the patients presented small declines in both estimated IQ and memory, which were more pronounced in patients with left TLE and in those with persistent seizures. Different surgical approaches did not impose differences in seizure control or in cognitive outcome. We observed small declines in cognitive scores with most of these patients, which were worse in patients with left-sided resection and in those who continued to suffer from postoperative seizures. We also demonstrated that manual volumetry can reveal a reduction in volume in the contralateral hippocampus, although this change was mild and could not be detected by visual analysis. These new findings suggest that dynamic processes continue to act after the removal of the hippocampus, and further studies with larger groups may help in understanding the underlying mechanisms.

Phylogenetic Analysis Of The Microbial Community In Hypersaline Petroleum Produced Water From The Campos Basin.

In this work the archaea and eubacteria community of a hypersaline produced water from the Campos Basin that had been transported and discharged to an onshore storage facility was evaluated by 16S recombinant RNA (rRNA) gene sequence analysis. The produced water had a hypersaline salt content of 10 (w/v), had a carbon oxygen demand (COD) of 4,300 mg/l and contains phenol and other aromatic compounds. The high salt and COD content and the presence of toxic phenolic compounds present a problem for conventional discharge to open seawater. In previous studies, we demonstrated that the COD and phenolic content could be largely removed under aerobic conditions, without dilution, by either addition of phenol degrading Haloarchaea or the addition of nutrients alone. In this study our goal was to characterize the microbial community to gain further insight into the persistence of reservoir community members in the produced water and the potential for bioremediation of COD and toxic contaminants. Members of the archaea community were consistent with previously identified communities from mesothermic reservoirs. All identified archaea were located within the phylum Euryarchaeota, with 98 % being identified as methanogens while 2 % could not be affiliated with any known genus. Of the identified archaea, 37 % were identified as members of the strictly carbon-dioxide-reducing genus Methanoplanus and 59 % as members of the acetoclastic genus Methanosaeta. No Haloarchaea were detected, consistent with the need to add these organisms for COD and aromatic removal. Marinobacter and Halomonas dominated the eubacterial community. The presence of these genera is consistent with the ability to stimulate COD and aromatic removal with nutrient addition. In addition, anaerobic members of the phyla Thermotogae, Firmicutes, and unclassified eubacteria were identified and may represent reservoir organisms associated with the conversion hydrocarbons to methane.