Estudo numérico do impacto das emissões veiculares e fixas da cidade de Manaus nas concentrações de poluentes atmosféricos da região amazônica

The main aim of this study was to evaluate the impact of the urban pollution plume from the city of Manaus by emissions from mobile and stationary sources in the atmospheric pollutants concentrations of the Amazon region, by using The Weather Research and Forecasting with Chemistry (WRF-Chem) model. The air pollutants analyzed were CO, NOx, SO2, O3, PM2.5, PM10 and VOCs. The model simulations have been configured with a grid spacing of 3 km, with 190 x and 136 y grid points in horizontal spacing, centered in the city of Manaus during the period of 17 and 18 of March 2014. The anthropogenic emissions inventories have gathered from mobile sources that were estimated the emissions of light and heavy-duty vehicles classes. In addition, the stationary sources have considered the thermal power plants by the type of energy sources used in the region as well as the emissions from the refinery located in Manaus. Various scenarios have been defined with numerical experiments that considered only emissions by biogenic, mobile and stationary sources, and replacement fuel from thermal power plant, along with a future scenario consisting with twice as much anthropogenic emissions. A qualitative assessment of simulation with base scenario has also been carried out, which represents the conditions of the region in its current state, where several statistical methods were used in order to compare the results of air pollutants and meteorological fields with observed ground-based data located in various points in the study grid. The qualitative analysis showed that the model represents satisfactorily the variables analyzed from the point of view of the adopted parameters. Regarding the simulations, defined from the base scenarios, the numerical experiments indicate relevant results such as: it was found that the stationary sources scenario, where the thermal power plants are predominant, resulted in the highest concentrations, for all air pollutants evaluated, except for carbon monoxide when compared to the vehicle emissions scenario; The replacement of the energy matrix of current thermal power plants for natural gas have showed significant reductions in pollutants analyzed, for instance, 63% reductions of NOx in the contribution of average concentration in the study grid; A significant increase in the concentrations of chemical species was observed in a futuristic scenario, reaching up to a 81% increase in peak concentrations of SO2 in the study area. The spatial distributions of the scenarios have showed that the air pollution plume from Manaus is predominantly west and southwest, where it can reach hundreds of kilometers to areas dominated by original soil covering.

Produção biológica integrada de hidrogénio e metano a partir de resíduos da indústria do biodiesel

Dissertação de Mestrado Integrado em Engenharia da Energia e do Ambiente

Características de cinzas e sua aplicação no tratamento de gases durante a gasificação de biomassa

Na procura de melhores combustíveis para a produção de energia térmica e energia elétrica, a biomassa apresenta-se como uma das fontes de energia renováveis menos prejudiciais ao meio ambiente, esta é considerada como um recurso neutro do ponto de vista de emissões de dióxido de carbono. Atualmente, a tecnologia predominante no domínio da conversão energética de biomassa por via termoquímica é a combustão. Contudo, verifica-se a procura de combustíveis de melhor qualidade produzidos a partir de biomassa, como por exemplo na forma gasosa (gás de combustível). A produção deste tipo de combustíveis gasosos envolvendo processos de gasificação carece do desenvolvimento de tecnologia que permita obter um gás combustível com características adequadas às utilizações pretendidas. Os problemas mais relevantes relacionados com a conversão termoquímica da biomassa incluem a produção de cinzas e de alcatrões, estes podem levar a vários problemas operatórios. O presente trabalho teve dois objetivos, a caracterização das cinzas resultantes do processo de combustão de biomassa e o estudo do efeito da aplicação das cinzas para melhorar as propriedades do gás produzido durante o processo de gasificação de biomassa, principalmente na redução de compostos condensáveis (alcatrões). As cinzas volantes da combustão de biomassa analisadas apresentam na sua constituição elementos químicos característicos da biomassa, onde o cálcio apresenta-se em concentrações mais elevadas. Em menores concentrações encontram-se sódio, magnésio, fósforo, enxofre, cloro, potássio, manganês e ferro. As cinzas de fundo, pelo contributo que a areia do leito tem, são caracterizadas por conterem grandes concentrações de silício. Durante os processos de gasificação de biomassa a concentração de compostos condensáveis diminuiu com o aumento da razão de equivalência. As cinzas, colocadas no reator de leito fixo, apresentam um efeito positivo sobre a qualidade do gás, nomeadamente um aumento de 47,8% no teor de H2 e de 11% de CO, consequentemente obteve-se um gás combustível com PCI (poder calorífico inferior) mais elevado.

The use of solar colletor for heating and electricity for a single family house

The presented work is related to the use of solar energy for the needs of heating and electricity for a single house located in Poland. Electricity will provided by energy conversion in the turbine by means of Organic Rankine Cycle (ORC), in which the operating medium (water heated in solar collector) is heating refrigerator in the heating exchanger. The solar installation is integrated with heat accumulator and wood boiler, which is used in the situation that collector is not enough to fill requirements of thermal comfort. There are chosen also all the necessary components of the system. In the work is also performed the economic assessment, by F chart method, to evaluate the profitability of the project, taking into total costs and savings.

Probabilistic design optimization of horizontal axis wind turbine rotors

Considerable interest in renewable energy has increased in recent years due to the concerns raised over the environmental impact of conventional energy sources and their price volatility. In particular, wind power has enjoyed a dramatic global growth in installed capacity over the past few decades. Nowadays, the advancement of wind turbine industry represents a challenge for several engineering areas, including materials science, computer science, aerodynamics, analytical design and analysis methods, testing and monitoring, and power electronics. In particular, the technological improvement of wind turbines is currently tied to the use of advanced design methodologies, allowing the designers to develop new and more efficient design concepts. Integrating mathematical optimization techniques into the multidisciplinary design of wind turbines constitutes a promising way to enhance the profitability of these devices. In the literature, wind turbine design optimization is typically performed deterministically. Deterministic optimizations do not consider any degree of randomness affecting the inputs of the system under consideration, and result, therefore, in an unique set of outputs. However, given the stochastic nature of the wind and the uncertainties associated, for instance, with wind turbine operating conditions or geometric tolerances, deterministically optimized designs may be inefficient. Therefore, one of the ways to further improve the design of modern wind turbines is to take into account the aforementioned sources of uncertainty in the optimization process, achieving robust configurations with minimal performance sensitivity to factors causing variability. The research work presented in this thesis deals with the development of a novel integrated multidisciplinary design framework for the robust aeroservoelastic design optimization of multi-megawatt horizontal axis wind turbine (HAWT) rotors, accounting for the stochastic variability related to the input variables. The design system is based on a multidisciplinary analysis module integrating several simulations tools needed to characterize the aeroservoelastic behavior of wind turbines, and determine their economical performance by means of the levelized cost of energy (LCOE). The reported design framework is portable and modular in that any of its analysis modules can be replaced with counterparts of user-selected fidelity. The presented technology is applied to the design of a 5-MW HAWT rotor to be used at sites of wind power density class from 3 to 7, where the mean wind speed at 50 m above the ground ranges from 6.4 to 11.9 m/s. Assuming the mean wind speed to vary stochastically in such range, the rotor design is optimized by minimizing the mean and standard deviation of the LCOE. Airfoil shapes, spanwise distributions of blade chord and twist, internal structural layup and rotor speed are optimized concurrently, subject to an extensive set of structural and aeroelastic constraints. The effectiveness of the multidisciplinary and robust design framework is demonstrated by showing that the probabilistically designed turbine achieves more favorable probabilistic performance than those of the initial baseline turbine and a turbine designed deterministically.

Projeto, implementação e análise de um conversor CC-CC de alto ganho e alto rendimento para aplicações fotovoltaicas

In recent years the photovoltaic generation has had greater insertion in the energy mix of the most developed countries, growing at annual rates of over 30%. The pressure for the reduction of pollutant emissions, diversification of the energy mix and the drop in prices are the main factors driving this growth. Grid tied systems plays an important role in alleviating the energy crisis and diversification of energy sources. Among the grid tied systems, building integrated photovoltaic systems suffers from partial shading of the photovoltaic modules and consequently the energy yield is reduced. In such cases, classical forms of modules connection do not produce good results and new techniques have been developed to increase the amount of energy produced by a set of modules. In the parallel connection technique of photovoltaic modules, a high voltage gain DC-DC converter is required, which is relatively complex to build with high efficiency. The current-fed isolated converters explored in this work have some desirable characteristics for this type of application, such as: low input current ripple and input voltage ripple, high voltage gain, galvanic isolation, feature high power capacity and it achieve soft switching in a wide operating range. This study presents contributions to the study of a high gain and high efficiency DC-DC converter for use in a parallel system of photovoltaic generation, being possible the use in a microinverter or with central inverter. The main contributions of this work are: analysis of the active clamping circuit operation proposing that the clamp capacitor connection must be done on the negative node of the power supply to reduce the input current ripple and thus reduce the filter requirements; use of a voltage doubler in the output rectifier to reduce the number of components and to extend the gain of the converter; detailed study of the converter components in order to raise the efficiency; obtaining the AC equivalent model and control system design. As a result, a DC-DC converter with high gain, high efficiency and without electrolytic capacitors in the power stage was developed. In the final part of this work the DC-DC converter operation connected to an inverter is presented. Besides, the DC bus controller is designed and are implemented two maximum power point tracking algorithms. Experimental results of full system operation connected to an emulator and subsequently to a real photovoltaic module are also given.

Unravelling metabolism of Leishmania by metabolomics

The leishmaniases are neglected tropical diseases with an urgent need for effective drugs. Better understanding of the metabolism of the causative parasites will hopefully lead to development of new compounds targeted at critical points of the parasite’s biochemical pathways. In my work I focused on the pentose phosphate pathway of Leishmania, specifically on transketolase, sugar utilisation, and comparison between insect and mammalian infective stages of the parasites. The pentose phosphate pathway (PPP) is the major cellular source of NADPH, an agent critical for oxidative stress defence. The PPP uses glucose, reduces the NADP+ cofactor and produces various sugar phosphates by mutual interconversions. One of the enzymes involved in this latter part is transketolase (TKT). A Leishmania mexicana cell line deleted in transketolase (Δtkt) was assessed regarding viability, sensitivity to a range of drugs, changes in metabolism, and infectivity. The Δtkt cell line had no obvious growth defect in the promastigote stage, but it was more sensitive to an oxidative stress inducing agent and most of the drugs tested. Most importantly, the Δtkt cells were not infective to mice, establishing TKT as a new potential drug target. Metabolomic analyses revealed multiple changes as a consequence of TKT deletion. Levels of the PPP intermediates upstream of TKT increased substantially, and were diverted into additional reactions. The perturbation triggered further changes in metabolism, resembling the ‘stringent metabolic response’ of amastigotes. The Δtkt cells consumed less glucose and glycolytic intermediates were decreased indicating a decrease in flux, and metabolic end products were diminished in production. The decrease in glycolysis was possibly caused by inhibition of fructose-1,6-bisphosphate aldolase by accumulation of the PPP intermediates 6-phosphogluconate and ribose 5-phosphate. The TCA cycle was fuelled by alternative carbon sources, most likely amino acids, instead of glucose. It remains unclear why deletion of TKT is lethal for amastigotes, increased sensitivity to oxidative stress or drop in mannogen levels may contribute, but no definite conclusions can be made. TKT localisation indicated interesting trends too. The WT enzyme is present in the cytosol and glycosomes, whereas a mutant version, truncated by ten amino acids, but retaining a C-terminal targeting sequence, localised solely to glycosomes. Surprisingly, cells expressing purely cytosolic or glycosomal TKT did not have different phenotypes regarding growth, oxidative stress sensitivity or any detected changes in metabolism. Hence, control of the subcellular localisation remains unclear as well as its function. However, these data are in agreement with the presumed semipermeable nature of the glycosome. Further, L. mexicana promastigote cultures were grown in media with different combinations of labelled glucose and ribose and their incorporation into metabolism was followed. Glucose was the preferred carbon source, but when not available, it could be fully replaced with ribose. I also compared metabolic profiles from splenic amastigotes, axenic amastigotes and promastigotes of L. donovani. Metabolomic analysis revealed a substantial drop in amino acids and other indications coherent with a stringent metabolic response in amastigotes. Despite some notable differences, axenic and splenic amastigotes demonstrated fairly similar results both regarding the total metabolic profile and specific metabolites of interest.

Liquid-phase alcohol promoted methanol synthesis from CO2 and H2

Methanol is an important and versatile compound with various uses as a fuel and a feedstock chemical. Methanol is also a potential chemical energy carrier. Due to the fluctuating nature of renewable energy sources such as wind or solar, storage of energy is required to balance the varying supply and demand. Excess electrical energy generated at peak periods can be stored by using the energy in the production of chemical compounds. The conventional industrial production of methanol is based on the gas-phase synthesis from synthesis gas generated from fossil sources, primarily natural gas. Methanol can also be produced by hydrogenation of CO2. The production of methanol from CO2 captured from emission sources or even directly from the atmosphere would allow sustainable production based on a nearly limitless carbon source, while helping to reduce the increasing CO2 concentration in the atmosphere. Hydrogen for synthesis can be produced by electrolysis of water utilizing renewable electricity. A new liquid-phase methanol synthesis process has been proposed. In this process, a conventional methanol synthesis catalyst is mixed in suspension with a liquid alcohol solvent. The alcohol acts as a catalytic solvent by enabling a new reaction route, potentially allowing the synthesis of methanol at lower temperatures and pressures compared to conventional processes. For this thesis, the alcohol promoted liquid phase methanol synthesis process was tested at laboratory scale. Batch and semibatch reaction experiments were performed in an autoclave reactor, using a conventional Cu/ZnO catalyst and ethanol and 2-butanol as the alcoholic solvents. Experiments were performed at the pressure range of 30-60 bar and at temperatures of 160-200 °C. The productivity of methanol was found to increase with increasing pressure and temperature. In the studied process conditions a maximum volumetric productivity of 1.9 g of methanol per liter of solvent per hour was obtained, while the maximum catalyst specific productivity was found to be 40.2 g of methanol per kg of catalyst per hour. The productivity values are low compared to both industrial synthesis and to gas-phase synthesis from CO2. However, the reaction temperatures and pressures employed were lower compared to gas-phase processes. While the productivity is not high enough for large-scale industrial operation, the milder reaction conditions and simple operation could prove useful for small-scale operations. Finally, a preliminary design for an alcohol promoted, liquid-phase methanol synthesis process was created using the data obtained from the experiments. The demonstration scale process was scaled to an electrolyzer unit producing 1 Nm3 of hydrogen per hour. This Master’s thesis is closely connected to LUT REFLEX-platform.

A contribution towards the performance and structural understanding of copper and nickel salts as ammonia stores

The ongoing depletion of fossil fuels and the severe consequences of the greenhouse effect make the development of alternative energy systems crucially important. While hydrogen is, in principle, a promising alternative, releasing nothing but energy and pure water. Hydrogen storage is complicated and no completely viable technique has been proposed so far. This work is concerned with the study of one potential alternative to pure hydrogen: ammonia, and more specifically its storage in solids. Ammonia, NH3, can be regarded as a chemical hydrogen carrier with the advantages of strongly reduced flammability and explosiveness as compared to hydrogen. Furthermore, ammine metal salts presented here as promising ammonia stores easily store up to 50 wt.-% ammonia, giving them a volumetric energy density comparable to natural gas. The model system NiX2–NH3 ( X = Cl, Br, I) is studied thoroughly with respect to ammine salt formation, thermal decomposition, air stability and structural effects. The system CuX2–NH3 ( X = Cl, Br) has an adverse thermal decomposition behaviour, making it impractical for use as an ammonia store. This system is, however, most interesting from a structural point of view and some work concerning the study of the structural behaviour of this system is presented. Finally, close chemical relatives to the metal ammine halides, the metal ammine nitrates are studied. They exhibit interesting anion arrangements, which is an impressive showcase for the combination of diffraction and spectroscopic information. The characterisation techniques in this thesis range from powder diffraction over single crystal diffraction, spectroscopy, computational modelling, thermal analyses to gravimetric uptake experiments. Further highlights are the structure solutions and refinements from powder data of (NH4)2[NiCl4(H2O)(NH3)] and Ni(NH3)2(NO3)2, the combination of crystallographic and chemical information for the elucidation of the (NH4)2[NiCl4(H2O)(NH3)] formation reaction and the growth of single crystals under ammonia flow, a technique allowing the first documented successful growth and single crystal diffraction measurement for [Cu(NH3)6]Cl2.

Proposta de uma matriz de decisão em energia hidrelétrica com o uso do método multicritério, para formulação de políticas públicas no estado do Paraná

Brazil is internationally acknowledged for its renewable sources, most notably, hydroelectric power plant projects which correspond to 65% of electricity production supply to the National Interconnected System. The main question behind this research is: what are the weights and the relative importance of the variables which have influence on the decision making process for the expansion of hydroelectric generation projects in Parana? The main objective is to propose a multi-criteria decision procedure, in association with water sources options that take into consideration the weight and relative importance of the alternatives having influence on the decision by enterprises in the generation of electricity in the state of Paraná. As far as the approach to the problem is concerned, this research can be classified as having mixed methodologies, applying Content Analysis, Delphi technique and the Analytic Hierarchy Process. Following Delphi methodology, a group of 21 was selected for data collection, all of those linked to Paranaense hydroelectricity market. And the main result was the construction of a decision tree in which it was possible to identify the importance and relative weight of the elements associated with the four dimensions of energy. In environmental dimension, the highest relative weight was placed on the loading capacity of Parana system; the economic dimension, the amortization of investment; in social dimension, the generation of direct work places and in institutional dimension, the availability of suitable sources of financing. Policy makers and business managers make their decisions based on specific criteria related to the organization segment, market information, economic and political behavior among other indicators that guide them in dealing with the typical tradeoffs of projects in hydropower area. The results obtained in the decision tree show that the economic bias is still the main factor in making investment decisions. However, environmental impacts on the State loading capacity, income generation, providing opportunities for direct as well as indirect jobs. And at an institutional level, the absence of funding sources show that the perception of experts is focused on other issues beyond the logic behind development per se. The order of priority of variables in this study indicates that in the current environment of uncertainty in the Brazilian economy as many variables must be analyzed and compared in order to optimize the scarce resources available to expand local development in relation to Paranaense water matrix.

Plataforma Cloud para monitoreo remoto de sistemas fotovoltaicos aislados en el Ecuador

Los sistemas fotovoltaicos son fuentes emergentes de energías renovables que generan electricidad a partir de la radiación solar. El monitoreo de los sistemas fotovoltaicos aislados proporciona información necesaria que permite a sus propietarios mantener, operar y controlar estos sistemas, reduciendo los costes de operación y evitando indeseadas interrupciones en el suministro eléctrico de zonas aisladas. En este artículo, se propone el desarrollo de una plataforma para el monitoreo de sistemas fotovoltaicos aislados en el Ecuador con el objetivo fundamental de desarrollar una solución escalable, basada en el uso de software libre, en el empleo de sensores de bajo consumo y en el desarrollo de servicios web en la modalidad ‘Software as a Service’ (SaaS) para el procesamiento, gestión y publicación de información registrada y la creación de un innovador centro de control solar fotovoltaico en el Ecuador.

Utilização de glúten de trigo na alimentação de dourada, Sparus aurata (Linnaeus, 1758)

A incorporação de fontes proteicas alternativas à farinha de peixe na alimentação de espécies piscícolas tem sido objecto de variados estudos no âmbito da nutrição animal. Neste contexto realizou-se o presente trabalho, cujo objectivo foi determinar o nível de substituição ideal de farinha de peixe por glúten de trigo na alimentação de dourada. Foram realizados dois ensaios, um de crescimento e um de digestibilidade. O ensaio de crescimento efectuou-se para determinar qual o nível máximo de substituição sem que os animais apresentassem diferenças significativas em termos de taxa de crescimento. O ensaio de digestibilidade teve como principal objectivo determinar qual das dietas testadas proporcionaria melhores valores de utilização digestiva por parte dos animais. Tendo em conta os resultados dos ensaios e as condições experimentais em que se realizaram, verificou-se que a substituição até 40% não afecta significativamente o desempenho zootécnico das douradas. ABSTRACT; The incorporation of alternative protein sources in fish diets has been the aim of many scientific experiments in animal nutrition. ln this study, the main objective was to evaluate the ideal level of wheat gluten incorporation in substitution of fishmeal in diets for gilthead sea bream (Sparus aurata L). To reach this objective, two experiments were carried out, in which growth and digestibility were studied. The aim of the growth experiment was to evaluate the maximum level of fish meal substitution by wheat gluten (20%, 40%, 60% and 80%), without affecting significantly the animals growth rate. The digestibility experiment took place to evaluate which animals presented better food utilization with the tested diets (20%, 40%, 60% and 80%). Observing the results of these two experiments, it was concluded that the substitution until 40% did not affect significantly the performance of the fishes.

Flowers of Gomphrena globosa L. as an alternatve source of betacyanins: optimization of the extraction using response surface methodology

Betacyanins are betalain pigments that display a red-violet colour which have been reported to be three times stronger than the red-violet dye produced by anthocyanins [1]. The applications of betacyanins cover a wide range of matrices, mainly as additives or ingredients in the food industry, cosmetics, pharmaceuticals and livestock feed. Although, being less commonly used than anthocyanins and carotenoids, betacyanins are stable between pH 3 to 7 and suitable for colouring in low acid matrices. In addition, betacyanins have been reported to display interesting medicinal character as powerful antioxidant and chemopreventive compounds either in vitro or in vivo models [2]. Betacyanins are obtained mainly from the red beet of Beta vulgaris plant (between I 0 to 20 mg per I 00 g pulp) but alternative primary sources are needed [3]. In addition, independently of the source used, the effect of the variables that affect the extraction of betacyanins have not been properly described and quantified. Therefore, the aim of this study was to identifY and optimize the conditions that maximize betacyanins extraction using the tepals of Gomphrena globosa L. flowers as an alternative source. Assisted by the statistical technique of response surface methodology, an experimental design was developed for testing the significant explanatory variables of the extraction (time, temperature, solid-liquid ratio and ethanolwater ratio). The identification was performed using high-performance liquid chromatography coupled with a photodiode array detector and mass spectrometry with electron spray ionization (HPLC-PDAMS/ ESI) and the response was measured by the quantification of these compounds using HPLC-PDA. Afterwards, a response surface analysis was performed to evaluate the results. The major betacyanin compounds identified were gomphrenin 11 and Ill and isogomphrenin IJ and Ill. The highest total betacyanins content was obtained by using the following conditions: 45 min of extraction. time, 35•c, 35 g/L of solid-liquid ratio and 25% of ethanol. These values would not be found without optimizing the conditions of the betacyanins extraction, which moreover showed contrary trends to what it has been described in the scientific bibliography. More specifically, concerning the time and temperature variables, an increase of both values (from the common ones used in the bibliography) showed a considerable improvement on the betacyanins extraction yield without displaying any type of degradation patterns.

Enquadramento legal e estudo económico de parques eólicos

Portugal, no intuito de alcançar metas ambientais e económicas a que se propôs, e de reduzir a dependência das importações de energia, tem aumentado o investimento em eletricidade produzida a partir de energias renováveis (FER-E). Apesar do consenso em torno da sua utilização, as energias renováveis deparam-se com barreiras de várias ordens que dificultam a sua difusão no mercado. A atuação do Estado neste enquadramento passa por criar modelos de promoção da FER-E. A maioria dos países da União Europeia, incluindo Portugal, aplica as tarifas feed-in (FIT) como instrumento central de suporte à FER-E, inserido num modelo de apoio que contempla outros parâmetros de construção considerados críticos para o seu sucesso. No seguimento do estágio realizado na empresa Senvion Portugal a presente tese explora os programas e modelos de apoio às FER-E em Portugal, nomeadamente as que se referem à energia eólica. Bem como os trabalhos realizados com as equipas de O&M e a realização de um estudo de viabilidade económica da substituição de aerogeradores no parque eólico de Picos Verdes II.

Ecological effects of flow and temperature regimes on fish communities in temperate rivers

Les organismes aquatiques sont adaptés à une grande variabilité hydrique et thermique des rivières. Malgré ceci, la régulation des eaux suscite des changements aux débits qui peuvent provoquer des impacts négatifs sur la biodiversité et les processus écologiques en rivière. Celle-ci peut aussi causer des modifications au niveau des régimes thermiques et des caractéristiques de l’habitat du poisson. Des données environnementales et biologiques décrivant l’habitat du poisson existent, mais elles sont incomplètes pour plusieurs rivières au Canada et de faible qualité, limitant les relations quantitatives débit-température-poissons à un petit nombre de rivières ou à une région étudiée. La recherche menée dans le cadre de mon doctorat concerne les impacts de la génération d'hydroélectricité sur les rivières; soit les changements aux régimes hydriques et thermiques reliés à la régulation des eaux sur la variation des communautés ichtyologiques qui habitent les rivières régulées et naturelles au Canada. Suite à une comparaison d’échantillonnage de pêche, une méthode constante pour obtenir des bons estimés de poisson (richesse, densité et biomasse des espèces) a été établie pour évaluer la structure de la communauté de poissons pour l’ensemble des rivières ciblées par l’étude. Afin de mieux comprendre ces changements environnementaux, les principales composantes décrivant ces régimes ont été identifiées et l’altération des régimes hydriques pour certaines rivières régulées a été quantifiée. Ces résultats ont servi à établir la relation significative entre le degré de changement biotique et le degré de changement hydrique pour illustrer les différences entre les régimes de régulation. Pour faire un complément aux indices biotiques déjà calculés pour l’ensemble des communautés de poissons (diversité, densité et biomasse des espèces par rivière), les différences au niveau des guildes de poissons ont été quantifiées pour expliquer les divers effets écologiques dus aux changements de régimes hydriques et thermiques provenant de la gestion des barrages. Ces derniers résultats servent à prédire pour quels traits écologiques ou groupes d’espèces de poissons les composantes hydriques et thermiques sont importantes. De plus, ces derniers résultats ont servi à mettre en valeur les variables décrivant les régimes thermiques qui ne sont pas toujours inclues dans les études hydro-écologiques. L’ensemble des résultats de cette thèse ont des retombées importantes sur la gestion des rivières en évaluant, de façon cohérente, l’impact de la régulation des rivières sur les communautés de poissons et en développant des outils de prévision pour la restauration des écosystèmes riverains.