Surface modification of polymeric materials by cold atmospheric plasma jet

In this work we report the surface modification of different engineering polymers, such as, polyethylene terephthalate (PET), polyethylene (PE) and polypropylene (PP) by an atmospheric pressure plasma jet (APPJ). It was operated with Ar gas using 10 kV, 37 kHz, sine wave as an excitation source. The aim of this study is to determine the optimal treatment conditions and also to compare the polymer surface modification induced by plasma jet with the one obtained by another atmospheric pressure plasma source the dielectric barrier discharge (DBD). The samples were exposed to the plasma jet effluent using a scanning procedure, which allowed achieving a uniform surface modification. The wettability assessments of all polymers reveal that the treatment leads to reduction of more than 40 degrees in the water contact angle (WCA). Changes in surface composition and chemical bonding were analyzed by x-ray photoelectron spectroscopy (XPS) and Fourier-Transformed Infrared spectroscopy (FTIR) that both detected incorporation of oxygen-related functional groups. Surface morphology of polymer samples was investigated by Atomic Force Microscopy (AFM) and an increase of polymer roughness after the APPJ treatment was found. The plasma-treated polymers exhibited hydrophobic recovery expressed in reduction of the O-content of the surface upon rinsing with water. This process was caused by the dissolution of low molecular weight oxidized materials (LMWOMs) formed on the surface as a result of the plasma exposure. (C) 2014 Elsevier B.V. All rights reserved.

Comparative study of toxicity of azo dye Procion Red MX-5B following biosorption and biodegradation treatments with the fungi Aspergillus niger and Aspergillus terreus

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Aquatic toxicity of dyes before and after photo-Fenton treatment

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Adsorção do corante luganil azul por espuma de poliuretano

The industrial development has created many environmental problems that can be observed through the changes in air, soil and water. The pollution of water bodies with compounds present in textile effluents cause beyond the visual pollution, changes in biological cycles, mainly by changing the process of photosynthesis. Due to these environmental implications it is necessary a treatment of livestock manure. The process of adsorption of the dye is a technique that has been successfully employed for effective removal of the color of the effluent. The purpose of this study was to investigate the application of a polyurethane foam plant of castor oil as an alternative adsorbent for removal of dyes in textile effluents. The study was conducted with the dye “luganil azul”, as adsorbent and the foam in a flexible manner and sprayed. It also investigated the influence of pH on the adsorption dye. The kinetic data were obtained, noting that the pH influence on adsorption. Adsorption isotherms of the dye in aqueous solution using the foam in a flexible manner also were determined experimentally.

Avaliação do potencial genotóxico e mutagênico do efluente de uma refinaria de petróleo e dos rios sob sua influência, por meio de bioensaios com Oreochromis niloticus (Perciformes, Cichlidae)

The petrochemical industry represents a sector of intense activity, in constant expansion and great economic importance for Brazil. In order to be used in various human activities petroleum needs to suffer a refinement process that, besides requiring large amounts of water, produces large amounts of wastes, which are discharged in hydric resources. Petroleum is a complex mixture mainly comprised by hydrocarbons, many of them are recognized as toxic chemicals, which are able to induce a considerable environmental pollution. Since water is an important resource for the maintenance of ecosystems and is also the final receiver of effluent discharges of the petroleum industry, there is an imminent need to monitor, constantly, the hydric resources that are influenced by this industrial activity, so that it can be ensured the environmental health. This study aimed, mainly, to analyze the quality of water samples derived from refinement process performed of the largest petroleum refinery in Brazil (REPLAN), in distinct steps of the industry treatment, and waters of rivers associated to its activity. Micronuclei and Nuclear Abnormalities tests were performed in erythrocytes of the fish species Oreochromis niloticus exposed to water samples derived from refinery use and to rivers under the influence of their effluents, in order to evaluate its possible toxic, genotoxic and mutagenic effects. The results obtained show that the treatment carried out by the refinery, during the evaluated periods, was effective, since the substances present in the water samples did not induce significant genotoxic and/or mutagenic alterations in the genetic material of the test organisms. On the other hand, when the substances present in the refinery effluent mix with the ones derived from other industrial activities developed upstream of this industry, the resultant compound, in some periods, presented genotoxic potencial, characterized by a rise of erythrocytic...

Remoção de cromo de resíduos de curtumes por argilitos da formação Corumbataí - SP

The tanning wastes are characterized to be significant sources of pollution in the hydrosphere when non adjusted or disposed adequated form. That happens because this industry type uses the chromium to tan hides, and this element is present in discharges concentrations in final wastes, characterizing this waste type as dangerous, according to the Associação Brasileira de Normas Técnicas, através da Norma Brasileira 10.004 de 2004. Due to this, the research proposes a form to reduction chromium of the tanning wastes through the process of adsorption. For that were used mining-wastes of Corumbataí Formation clays, material commonly used in the production of ceramic products in Rio Claro (SP). They were accomplished laboratory essays that involved the preparation of different clays pulps and subsequent mixture of these with the tanning wastes, maintaining them under different mixing times and adsorption contacts. After the separation of the mixtures, the leached were chemically analyzed and it was seen the efficiency of chromium reduction and your relationship with the variation of different times of contact clays/wastes and different grain sizes used in the pulps preparation.

Uso de sistemas construídos de áreas alagadas (Constructed Wetland System - CWS) para tratamento de efluentes

A large proportion of fresh water is greatly impaired due to increasing pollution; this could be minimized through the expansion of investment in sanitation programs. But the major problem faced by third world countries and developing ones in this respect, is the high cost of projects and their implementation. In an attempt to find a simple technology, efficient and inexpensive, this study aimed to verify the effectiveness of using constructed wetland systems (CWS) for removal of bacteria and nutrients from sanitary sewer effluent from the STS Piracicamirim - Piracicaba - SP. The installation of prototypes was followed, and testing prior to regularize the flow held, but due to malfunction of these and outages of the STS activity can not evaluate the effectiveness of both as to the parameters proposed: temperature, pH, dissolved oxygen, conductivity, total dissolved solids (TDS), nitrite, nitrate, ammonia, total nitrogen, total phosphorus, chemical oxygen demand (COD), sulfide, sulfate, biochemical oxygen demand (BOD), total coliform and Escherichia coli. To establish results about the effectiveness of these types if the system were conducted literature reviews of papers published with the same theme. Analysis of these results showed fairly good efficiencies in wastewater treatment, especially for nutrients and coliforms

Uso de sistemas construídos de áreas alagadas (Constructed Wetland System - CWS) tipo ascendente/descendente, para tratamento de efluentes avícolas

Human development and population growth during the twentieth century increased the water demand, tripling its consumption between 1950 and 1990. As the water streams were polluted; and as water is the source of minerals and also regulates vital functions, it becomes the vehicle of transmission and consequently spreads many diseases. Probably, the industries are the major responsible for this pollution when they dump untreated effluents to water streams, saturating the already insufficient net of sanitation facilities polluting water and soil. An effective treatment has been established with low cost in Europe and the United States, through constructed systems on wetlands Constructed Wetland Systems - CWSs, gradually used in other countries in the last three decades. Lately, we observe a continuous growth in Brazilian poultry business, and poultry industry showed greatest dynamism in the country, following the global market. Pondering this information and the efficiency of such treatment, this work aimed to study prototypes, in a laboratory scale, simulating ascending and descending types of CWSs, vegetated with aquatic macrophytes Eichhornia crassipes and the uses of aggregates and soil, to treat industrial wastewater from slaughterhouses and aviary. We conducted the initial characterization of the effluent to have an idea of its constituents and to scale the system and the continuous flow. Furthermore, we characterized the soil to be used in this system. The collects are periodically made in the refrigeration industry FRICOCK FRIGORIFICAÇÃO AVICULTURA INDÚSTRIA E COMÉRCIO LTDA. for local treatment simulation. The effluent that was treated with 12 prototypes of CWSs are analyzed with some frequency. The results of these reviews were compared to the effluent coming from the industry... (Complete abstract click electronic access below)

Tratamento de águas oleosas oriundas do processo de produção de óleo de dendê utilizando a flotação por ar dissolvido

This study was developed to evaluate the performance of different coagulant and pH dosages by applying the use of Dissolved Air Flotation (FAD) to enable its use in effluent treatment of the extraction process of palm oil. The study was developed in the laboratory, where studies about emulsions stability were made for the production of a synthetic effluent which best suit the characteristics of raw effluent. The synthetic water that would be used in the tests of FAD was produced, once the stability and characterization which best approached the raw wastewater was obtained. Trials tested three coagulant doses, combined with various pH ranges and five upward velocities (Va), finding an optimal range of this combination. Some operating parameters such as time and gradient of rapid mixing (20 s / 1000 s-1), time and gradient flotation (15 min / 60 s-1), chamber pressure saturation (450 kPa) and recirculation rate (20%) were set. In this way, samples were collected for analysis of the removal of turbidity parameters, suspended solids and oils and greases. This one is obtained by a correlation turbidity x oils and greases, referring to the previous analysis. The degree of removal obtained were 73,97% for turbidity, 51,4% for total suspended solids and 86,2% for oils and greases. Removal rates may be increased in later studies, by ranging the velocity gradient and flocculation parameters and the recirculation ratio, and by using lower flotation speeds to these effluent characteristics.

Ajuste do modelo QUAL2K e simulação de cenários para o Ribeirão Claro

The project has as objective to adjust the model QUAL2K to “Ribeirão Claro” river to evaluate the behavior of OD and DBO when are simulated the following sceneries: (i) implantation of a hypothetic wastewater station treatment that treats all the effluent thrown nowadays in the body of water; (ii) increase of withdrawal flow of DAAE to public supply and (iii) increase of nowadays flow of wastewater throwing, being the two last caused for the population increasing. The results obtained allowed to conclude that the model QUAL2K presented a good adjustment to the variable OD and a reasonable adjustment to the variable DBO, being that the same was suitable to the simulation of the sceneries proposed.

Avaliação da auto-suficiência energética em reatores anaeróbios aplicados ao tratamento de resíduos da indústria de produção do etanol

Ethanol, the main automotive biofuel, has its production based on the fermentation of sugars found in biological materials and on the distillation of the alcoholic media formed during the fermentative process. Stillage is the main residue from ethanol production, containing a high organic loading in addition to acidic and corrosive characteristics. Considering the available technologies to treat stillage, we highlight anaerobic digestion, which allows the reduction of the impacts associated to pollutants loading of this effluent and the generation of energy from the methane gas produced in the process. Based on the high treatment efficiency usually associated to the anaerobic process, this work aimed to assess whether anaerobic systems applied to the treatment of stillage are energetically self-sufficient. First we evaluated the energy recovery capacity in an anaerobic reactor applied to the treatment of stillage resulting from corn-to-ethanol processing. The results indicated the great influence that a correct selection of electrical equipment and their respective operating periods have on the net energy balance of the anaerobic treatment. The high energy consumption of the heater would not allow the system to achieve a positive net energy balance – the maximum energy recovery would reach only 0.68% of the consumption. However, the replacement of the mixture equipment would result in energy gains ranging from 8.5 to 967.9% of the consumption. In this work we also assessed the efficiency of methane yields for a few studies and the correlation between some parameters of the anaerobic process. With respect to the methane yield, we noted that mesophilic systems tend to be more advantageous than the thermophilic ones (efficiency of 76.45 ± 22.51% vs. 69.40 ± 30.36%). Considering the study... (Complete abstract click electronic access below)

Análise ambiental em um canteiro de obras

The building sector can cause the environmental degradation, by the natural resources consumption, machinery use and natural landscape modifying. The environmental management system (EMS) improves the environmental quality and makes the companies more competitive. So, this work developed an environmental management system in a building site focused on the solid waste and in the development of mitigation proposals for the most significant environmental impacts. To develop this work it was necessary to follow the building site activities; evaluate the solid waste management; identify the law requirements; identify the environmental aspects and impacts; evaluate the environmental impacts; and propose alternatives for mitigating the adverse environmental critical impacts. The main proposals are the reduction of the waste generation in the place that it’s generated; the reuse and correct final disposal of that wastes; the treatment and reuse of the effluent; and the supervising in the trucks and machineries avoiding the oil spilling and the air pollution

Remoção de matéria orgânica e nitrogênio de efluentes provenientes de abatedouros de bovinos por meio de reator aeróbio operando em bateladas sequenciais com adição de coagulante químico

The volume of liquid effluent generated in cattle slaughterhouses is quite high and cannot be released untreated in water bodies due to its high pollution load of predominantly organic origin. To minimize the environmental impacts of its industrial wastewater and meet the local environmental legislation, abattoirs shall make the treatment of these effluents. The present work aims to develop the study of a reactor by sequential batch pilot scale, in order to optimize their performance in treating wastewater from a cattle slaughterhouse. The treatment system used was developed and installed in the Laboratory of Wastewater Treatment, in Faculty of Science and Technology UNESP, Presidente Prudente campus. The procedure used followed the operation of sequential batch reactors, in which all processes and treatment operations occurring sequentially in a single unit, by establishing specific operating cycles, which comprise the following separated phases: aerobic reaction, anoxic reaction, sedimentation and emptying. Aiming to improve the quality of treatment was planned the addition of coagulant Poly Aluminum Chloride (PAC) in the reactor, by determining their optimal dosage by Jar-test trials. Were prepared four steps with specific operating cycles: step one or acclimatization (10 hour of aeration, one hour and 30 minutes of sedimentation and 30 minutes for exchanging the effluent); step 2 (6 hours of aeration or aerobic phase, 4 hours and 45 minutes of stirring or anoxic phase and 1 hour and 15 minutes for sedimentation and exchange effluent); step 3 (2 hours and 30 minutes of aeration, 8 hours and 15 minutes of stirring and 1 hour and 15 minutes for sedimentation and exchange) and step 4 (2 hours of aeration, 8 hours and 45 minutes of stirring and 1 hour and 15 minutes for sedimentation and exchange)... (Complete abstract click electronic access below)

Avaliação da toxicidade sobre Ceriodaphnia dubia das águas dos rios Atibaia, Jaguari e efluente tratado de refinaria de petróleo

Ensuring availability of quality water for human consumption causes becomes an increasing number of studies for the analysis of effluent before and after treatment, so that its release into receiving bodies do not cause significant changes in the river water and on the biological communities related to them. The biomarkers of toxicity have long been used to verify the potential toxic effluent and its correlation with the treatment efficiency of them. In this context, the cladoceran Ceriodaphnia dubia stands out because it is a benthic aquatic organism highly sensitive to environmental changes. In this study, to evaluate the interference of the release of treated wastewater of oil refinery in Rio Atibaia, we sought to determine the toxicity on population dynamics of Ceriodaphnia dubia microcrustacean in water samples upstream and downstream from the launch site, compared with samples from Rio Jaguarí at the point of capture by the company itself and treated effluent. We have studied the number of offspring produced in 10 replicates, each starting with a test individual of up to 24 hours for each sample and correlated the results with physical-chemical and microbiological tests performed by a laboratory technician. For most tests, the results indicate that the treated effluent gives sub-lethal toxicity to the microcrustacean, as delay the onset of the reproductive cycle of the same

Comparação de eficiências do uso de sistemas construídos de áreas alagadas (Constructed Wetland Systems - CWS), tipos ascendente e descendente, para tratamento de efluentes

Water is an essential element for life. The use of this element, to support the community, defines it as water resource. This feature is being misused and degraded by the dumping of highly contaminated effluents. The impoverishment of its quality poses a risk to human consumption. The necessity to manage this resource, treating the wastewater properly, requires the constant improvement of treatment systems. Another need is to adjust the cost of systems to the demands of communities with less financial clout. This study aimed to adapt and understand the systems of wetlands, improving its efficiency, in an attempt to collaborate with the enrichment of this technology. The practical evidence, with lab-scale prototypes, assembled in ETE Piracicamirim with urban sewage effluent contributed to highlight the problems and operating system design. The bibliographic review showed that several studies had effectiveness for treatment. But it was evident the need for better understanding of dimensioning definitions that better attempted to the answers into the project. Moreover, standardization of system conditions for the specific wastewater treatment is an interesting field, identified, for future studies yet contribute to environmental engineering and sanitation