935 resultados para TOP-pelletti
Resumo:
In order to effectively suppress the noise radiation from large electrical power transformers, both the structure-borne and air-borne sound fields need to be characterised. The characterisation can be made either from theoretical predictions or by in-situ measurements. This paper presents the study of the sound radiation from a large power transformer in a substation. The radiation pattern can be predicted from the measured acceleration distribution and the predicted value is not affected by other noise sources. Alternatively, the farfield sound pressure level can be predicted from the sound pressure level measured at NEMA locations. Both the near- and far-field power radiation can be in-situ measured using the sound intensity technique. It is shown that both the vibration of a transformer tank wall and the radiated noise consist of a series of tonal components mainly at the first few harmonic frequencies of 100 Hz. Also, the neglect of the noise radiation from the transformer (top and bottom) lids does not affects the accuracy of the transformer radiation characterisation. (C) 1998 Elsevier Science Ltd. All rights reserved.
Resumo:
A variable-density groundwater model is used to analyse the effects of tidal fluctuations on sea-water intrusion in an unconfined aquifer. It is shown that the tidal activity forces the sea-water to intrude further inland and it also creates a thicker interface than would occur without tidal effects. Moreover, the configuration of the interface is radically changed when the tidal fluctuations are included. This is because of the dramatic changes in the flow pattern and velocity of the groundwater near the shoreline. For aquifer depths much larger than tidal amplitudes, the tidal fluctuation does not have much effect on how far the sea-water intrudes into the aquifer; nevertheless, a significant change in the configuration of concentration contours because of the effect of tidal fluctuations is observed. This change is more noticeable at the top of the aquifer, near the water table, than at the bottom of the aquifer, and is caused by the infiltration of salt water into the top of the aquifer at higher tidal levels. A flatter beach slope, therefore, intensifies this phenomenon. The interface configurations do not change noticeably over the course of a tidal cycle. Neglecting tidal fluctuation effects results in an inaccurate evaluation of the water table elevation at the land end of the aquifer, although no distinguishable difference is seen between the water tables near the shoreline. Where the landward boundary condition is a constant head, the effects of tidal fluctuations on sea-water intrusion are more pronounced than for cases where the landward boundary condition is a specified flux. Also it is shown that the effects of tidal fluctuations are more significant for a sloping beach than for a vertical shoreline and the salt water intrudes further inland for the sloping case. (C) 1999 Elsevier Science B.V. All rights reserved.
Theoretical and numerical analyses of convective instability in porous media with upward throughflow
Resumo:
Exact analytical solutions have been obtained for a hydrothermal system consisting of a horizontal porous layer with upward throughflow. The boundary conditions considered are constant temperature, constant pressure at the top, and constant vertical temperature gradient, constant Darcy velocity at the bottom of the layer. After deriving the exact analytical solutions, we examine the stability of the solutions using linear stability theory and the Galerkin method. It has been found that the exact solutions for such a hydrothermal system become unstable when the Rayleigh number of the system is equal to or greater than the corresponding critical Rayleigh number. For small and moderate Peclet numbers (Pe less than or equal to 6), an increase in upward throughflow destabilizes the convective flow in the horizontal layer. To confirm these findings, the finite element method with the progressive asymptotic approach procedure is used to compute the convective cells in such a hydrothermal system. Copyright (C) 1999 John Wiley & Sons, Ltd.
Resumo:
To investigate the influence of physical activity on bone mineral accrual during the adolescent years, we analyzed 6 years of data from 53 girls and 60 boys. Physical activity, dietary intakes, and anthropometry were measured every 6 months and dual-energy X-ray absorptiometry scans of the total body (TB), lumbar spine (LS), and proximal femur (Hologic 2000, array mode) were collected annually. Distance and velocity curves for height and bone mineral content (BMC) were fitted for each child at several skeletal sites using a cubic spline procedure, from which ages at peak height velocity (PHV) and peak BMC velocity (PBMCV) were identified. A mean age- and gender-specific standardized activity (Z) score was calculated for each subject based on multiple yearly activity assessments collected up until age of PHV. This score was used to identify active (top quartile), average (middle 2 quartiles), or inactive (bottom quartile) groups. Two-way analysis of covariance, with height and weight at PHV controlled for, demonstrated significant physical activity and gender main effects (but no interaction) for PBMCV, for BMC accrued for 2 years around peak velocity, and for BMC at 1 year post-PBMCV for the TB and femoral neck and for physical activity but not gender at the LS (all p < 0.05). Controlling for maturational and size differences between groups, we noted a 9% and 17% greater TB BMC for active boys and girls, respectively, over their inactive peers 1 year after the age of PBMCV. We also estimated that, on average, 26% of adult TB bone mineral was accrued during the 2 years around PBMCV.
Resumo:
In the first of three experiments, 11 participants generated pronation and supination movements of the forearm, in time with an auditory metronome. The metronome frequency was increased in eight steps (0.25 Hz) from a base frequency of 1.75 Hz. On alternating trials, participants were required to coordinate either maximum pronation or maximum supination with each beat of the metronome. In each block of trials, the axis of rotation was either coincident with the long axis of the forearm, above this axis, or below this axis. The stability of the pronate-on-the-beat pattern, as indexed by the number of pattern changes, and the time of onset of pattern change, was greatest when the axis of rotation of the movement was below the long axis of the forearm. In contrast, the stability of the supinate-on-the-beat pattern was greatest when the axis of rotation of the movement was above the long axis of the forearm. In a second experiment, we examined how changes in the position of the axis of rotation alter the activation patterns of muscles that contribute to pronation and supination of the forearm. Variations in the relative dominance of the pronation and supination phases of the movement cycle across conditions were accounted for primarily by changes in the activation profile of flexor carpi radialis (FCR) and extensor carpi radialis longus (ECR). In the Final experiment we examined how these constraints impact upon the stability of bimanual coordination. Thirty-two participants were assigned at random to one of four conditions, each of which combined an axis of rotation configuration (bottom or top) for each limb. The participants generated both inphase (both limbs pronating simultaneously, and supinating simultaneously) and antiphase (left limb pronating and right limb supinating simultaneously, and vice versa) patterns of coordination. When the position of the axis of rotation was equivalent for the left and the right limb, transitions from antiphase to inphase patterns of coordination were Frequently observed. In marked contrast, when the position of the axis of rotation for the left and right limb was contradistinct, transitions From inphase to antiphase patterns of coordination occurred. The results demonstrated that when movements are performed in an appropriate mechanical context, inphase patterns of coordination are less stable than antiphase patterns.
Resumo:
This is an overview of the first burden of disease and injury studies carried out in Australia. Methods developed for the World Bank and World Health Organization Global Burden of Disease Study were adapted and applied to Australian population health data. Depression was found to be the top-ranking cause of non-fatal disease burden in Australia, causing 8% of the total years lost due to disability in 1996. Mental disorders overall were responsible for nearly 30% of the non-fatal disease burden. The leading causes of total disease burden (disability-adjusted life years [DALYs]) were ischaemic heart disease and stroke, together causing nearly 18% of the total disease burden. Depression was the fourth leading cause of disease burden, accounting for 3.7% of the total burden. Of the 10 major risk factors to which the disease burden can be attributed, tobacco smoking causes an estimated 10% of the total disease burden in Australia, followed by physical inactivity (7%).
Resumo:
We consider continuous observation of the nonlinear dynamics of single atom trapped in an optical cavity by a standing wave with intensity modulation. The motion of the atom changes the phase of the field which is then monitored by homodyne detection of the output field. We show that the conditional Hilbert space dynamics of this system, subject to measurement-induced perturbations, depends strongly on whether the corresponding classical dynamics is regular or chaotic. If the classical dynamics is chaotic, the distribution of conditional Hilbert space vectors corresponding to different observation records tends to be orthogonal. This is a characteristic feature of hypersensitivity to perturbation for quantum chaotic systems.
Resumo:
Rheological properties of nine unprocessed unifloral Australian honeys (bloodwood, blue top iron bark, gum top, heath, narrow leafed iron bark, stringy bark, tea tree yapunyah and yellow box) were analysed over a range of temperatures (1-40 degreesC) The temperature effect on the viscosity follow ed an Arrhenius-type relationship and ail honey varieties exhibited Newtonian behaviour. if the Arrhenius equation constants (mu (0) and E-a) for a particular honey are known, the Arrhenius model can be used to calculate the viscosity of these honeys at specific temperatures, negating the need for tedious viscosity determination. (C) 2000 Academic Press.
Resumo:
Background We present a method (The CHD Prevention Model) for modelling the incidence of fatal and nonfatal coronary heart disease (CHD) within various CHD risk percentiles of an adult population. The model provides a relatively simple tool for lifetime risk prediction for subgroups within a population. It allows an estimation of the absolute primary CHD risk in different populations and will help identify subgroups of the adult population where primary CHD prevention is most appropriate and cost-effective. Methods The CHD risk distribution within the Australian population was modelled, based on the prevalence of CHD risk, individual estimates of integrated CHD risk, and current CHD mortality rates. Predicted incidence of first fatal and nonfatal myocardial infarction within CHD risk strata of the Australian population was determined. Results Approximately 25% of CHD deaths were predicted to occur amongst those in the top 10 percentiles of integrated CHD risk, regardless of age group or gender. It was found that while all causes survival did not differ markedly between percentiles of CHD risk before the ages of around 50-60, event-free survival began visibly to differ about 5 years earlier. Conclusions The CHD Prevention Model provides a means of predicting future CHD incidence amongst various strata of integrated CHD risk within an adult population. It has significant application both in individual risk counselling and in the identification of subgroups of the population where drug therapy to reduce CHD risk is most cost-effective. J Cardiovasc Risk 8:31-37 (C) 2001 Lippincott Williams & Wilkins.
Resumo:
Background: Between 1998 and 1999, a burden of disease assessment was carried out in Victoria, Australia applying and improving on the methods of the Global Burden of Disease Study. This paper describes the methods and results of the calculations of the burden due to 22 mental disorders, adding 14 conditions not included in previous burden of disease estimates, Methods: The National Survey of Mental Health and Wellbeing provided recent data on the occurrence of the major adult mental disorders in Australia. Data from international studies and expert advice further contributed to the construction of disease models, describing each condition in terms of incidence, average duration and level of severity, with adjustments for comorbidity with other mental disorders. Disability weights for the time spent in different states of mental ill health were borrowed mainly from a study in the Netherlands, supplemented by weights derived in a local extrapolation exercise. Results: Mental disorders were the third largest group of conditions contributing to the burden of disease in Victoria, ranking behind cancers and cardiovascular diseases. Depression was the greatest cause of disability in both men and women. Eight other mental disorders in men and seven in women ranked among the top twenty causes of disability. Conclusions: Insufficient information on the natural history of many of the mental disorders, the limited information on the validity of mental disorder diagnoses in community surveys and considerable differences between ICD-10 and DSM-IV defined diagnoses were the main concerns about the accuracy of the estimates. Similar and often greater concerns have been raised in relation to the estimation of the burden from common non-fatal physical conditions such as asthma, diabetes and osteoarthritis. In comparison, psychiatric epidemiology can boast greater scientific rigour in setting standards for population surveys.
Resumo:
We use the finite element method to model the heat transfer phenomenon through permeable cracks in hydrothermal systems with upward throughflow. Since the finite element method is an approximate numerical method, the method must be validated before it is used to soh,e any new, kind of problem. However, the analytical solution, which can be used to validate the finite element method and other numerical methods, is rather limited in the literature, especially, for the problem considered here. Keeping this in mind, we have derived analytical solutions for the temperature distribution along the vertical axis of a crack in a fluid-saturated porous layer. After the finite element method is validated by comparing the numerical solution with the analytical solution for the same benchmark problem, it is used to investigate the pore-fluid flow and heat transfer in layered hydrothermal systems with vertical permeable cracks. The related analytical and numerical results have demonstrated that vertical cracks are effective and efficient members to transfer heat energy from the bottom section to the top section in hydrothermal systems with upward throughflow.
Resumo:
This work presents new Structural data from a high-pressure/low-temperature (HP/LT) metamorphic terrane exposed on the islands of Syros and Sifnos (Cyclades, Greece). The structure and the metamorphism of a relatively coherent HP/LT rock section were studied in order to elucidate how strain was accommodated at deep crustal levels during the formation and exhumation of HP/LT rocks. At least three deformation phases associated with eclogite- and blueschist-facies conditions (P = 8-15 kbar; T = 400-550 degreesC) were recognised. The earliest deformation fabric (S1), preserved as inclusion trails within garnet porphyroblasts, is aligned to define a sub-vertical schistosity (at present orientation), which is frequently orthogonal to the flat matrix schistosity (S2), and may indicate that deep crustal thickening involved upright folding. The currently dominant fabric in the HP rock section, S2, is Usually moderately dipping and locally contains NW-trending glaucophane lineations, symmetric pressure-shadows and eclogitic boudins. The symmetric structures associated with this fabric seem to indicate coaxial vertical thinning, although the existence of non-coaxial structures out of the study area cannot be excluded. Glaucophane-bearing shear bands (S3), with top-to-NW sense of shearing, locally crosscut the earlier structures. The latest recognised fabric (D4) is scarce and often absent within the HP rocks. It is associated with top-to-NE kinematic criteria that formed at greenschist-facies conditions (P = 4-7 kbar; T = 400-450 degreesC). Based on these observations, it is suggested that partitioning of strain occurred at different crustal levels and at different times. Deep crustal deformation was governed by thickening via upright folding followed by coaxial vertical thinning, whereas non-coaxial shearing occurred when the rocks were already exhumed to relatively shallow crustal levels. The earliest fabrics (D1 to D3) pertain to Alpine orogenesis and possibly to syn-orogenic extension, whereas the latest correspond to whole-crust back-are extension. (C) 2002 Elsevier Science Ltd. All rights reserved.
Resumo:
Slumping of hardsetting seedbeds upon wetting is likely to determine the shrinking and development of strength on drying. Different processes have been invoked, including aggregate disruption, material relocation, and compaction. To gain a better understanding of the role played by compaction compared with aggregate disruption in seedbed slumping and shrinking, mechanical analysis was combined with previous morphogenetical description. The global structural behavior of repacked seedbeds of a hardsetting sandy loam soil was studied after wetting and again after subsequent drying. Bulk density was measured in 5-mm-depth increments using gamma attenuation, and water content was determined at 10-mm-depth increments. Various wetting conditions were used to simulate a range of climatic and management conditions, including flood irrigation, furrow irrigation of a formed seedbed, drip irrigation, and rainfall. Aggregate coalescence under overburden pressure played the main role in slumping, even though microcracking enhanced coalescence. Most of the slumping occurred at calculated effective stress > 1.1 kPa. Intense aggregate breakdown at the top of seedbeds under fast wetting led to slight slumping because the resulting clogging of the initial interaggregate packing voids was balanced, in part, by the increase in microporosity resulting from aggregate disruption. However, aggregate coalescence induced by overburden pressure developing at the seedbed bottom often resulted in a strong decrease in total porosity. The effect of rainfall kinetic energy on crust bulk density was strong compared with the effect of fast wetting (bulk density increase of about 0.07 Mg m(-3) and 0.03 Mg m(-3), respectively) and could be ascribed to compaction rather than to aggregate breakdown. Shrinking on drying was related to the continuity of the microstructure resulting from wetting rather than to the intensity of slumping. Aggregate breakdown led to more shrinking than did aggregate coalescence.
Resumo:
Exact analytical solutions of the critical Rayleigh numbers have been obtained for a hydrothermal system consisting of a horizontal porous layer with temperature-dependent viscosity. The boundary conditions considered are constant temperature and zero vertical Darcy velocity at both the top and bottom of the layer. Not only can the derived analytical solutions be readily used to examine the effect of the temperature-dependent viscosity on the temperature-gradient driven convective flow, but also they can be used to validate the numerical methods such as the finite-element method and finite-difference method for dealing with the same kind of problem. The related analytical and numerical results demonstrated that the temperature-dependent viscosity destabilizes the temperature-gradient driven convective flow and therefore, may affect the ore body formation and mineralization in the upper crust of the Earth. Copyright (C) 2003 John Wiley Sons, Ltd.
Resumo:
Consumers worldwide are increasingly concerned with sustainable production and consumption. Recently, a comprehensive study ranked 17 countries in regard to their environmentally friendly behaviour among consumers. Brazil was one of the top countries in the list. Yet, several studies highlight significant differences between consumers` intentions to consume ethically, and their actual purchase behaviour: the so-called `Attitude-Behaviour Gap`. In developing countries, few studies have been conducted on this issue. The objective of this study is therefore to investigate the gap between citizens` sustainability-related attitudes and food purchasing behaviour using empirical data from Brazil. To this end, Brazilian citizens` attitudes towards pig production systems were mapped through conjoint analysis and their coexistence with relevant pork product-related purchasing behaviour of consumers was investigated through cluster analysis. The conjoint experiment was carried Out with empirical data collected from 475 respondents surveyed in the South and Center-West regions of Brazil. The results of the conjoint analysis were used for a subsequent cluster analysis in order to identify clusters of Brazilian citizens with diversified attitudes towards pig production systems, using socio-demographics, attitudes towards sustainability-related themes that are expected to influence the way they evaluate pig production systems, and consumption frequency of various pork products as clusters` background information. Three clusters were identified as `indifferent`, `environmental conscious` and `sustainability-oriented` citizens. Although attitudes towards environment and nature had indeed an influence on citizens` specific attitudes towards pig farming at the cluster level, the relationship between `citizenship` and consumption behaviour was found to be weak. This finding is similar to previous research conducted with European consumers: what people (in their role of citizens) think about pig production systems does not appear to significantly influence their pork consumption choices. Improvements in the integrated management of this chain would better meet consumers` sustainability-related expectations towards pig production systems.