Influence of kaolinite/carbon black hybridization on combustion and thermal decomposition behaviors of NR composites

A series of NR composites filled with modified kaolinite (MK), carbon black (CB) and the hybrid fillercontained MK and CB, were prepared by melt blending. The microstructure, combustion and thermaldecomposition behaviors of NR composites were characterized by TEM, XRD, infrared spectroscopy, conecalorimeter test (CCT) and thermal-gravimetric analysis (TG). The results show that the filler hybridizationcan improve the dispensability and shape of the kaolinite sheets in the rubber matrix and change theinterface bond between kaolinite particles and rubber molecules. NR-3 filled by 10 phr MK and 40 phr CBhas the lowest heat release rate (HRR), mass loss rate (MLR), total heat release (THR), smoke productionrate (SPR) and the highest char residue among all the NR composites. Therefore, the hybridization ofthe carbon black particles with the kaolinite particles can effectively improve the thermal stability andcombustion properties of NR composites.

Fine tuning of elasticity via crosslinking collagen-based materials to mediate mechanotransduction and stability using corona treatment

The common goal of tissue engineering is to develop substitutes that can closely mimic the structure of extracellular matrix (ECM). However, similarly important is the intensive material properties which have often been overlooked, in particular, for soft tissues that are not to bear load assumingly. The mechanostructural properties determine not only the structural stability of biomaterials but also their physiological functionality by directing cellular activity and regulating cell fate decision. The aim here is to emphasize that cells could sense intensive material properties like elasticity and reside, proliferate, migrate and differentiate accordinglyno matter if the construct is from a natural source like cartilage, skin etc. or of synthetic one. Meanwhile, the very objective of this work is to provide a tunable scheme for manipulating the elasticity of collagen-based constructs to be used to demonstrate how to engineer cell behavior and regulate mechanotransduction. Articular cartilage was chosen as it represents one of the most complex hierarchical arrangements of collagen meshwork in both connective tissues and ECM-like biomaterials. Corona discharge treatment was used to produce constructs with varying density of crosslinked collagen and stiffness accordingly. The results demonstrated that elastic modulus increased up to 33% for samples treated up to one minute as crosslink density was found to increase with exposure time. According to the thermal analysis, longer exposure to corona increased crosslink density as the denaturation enthalpy increased. However the spectroscopy results suggested that despite the stabilization of the collagen structure the integrity of the triple helical structure remained intact. The in vitro superficial culture of heterologous chondrocytes also determined that the corona treatment can modulate migration with increased focal adhesion of cells due to enhanced stiffness, without cytotoxicity effects, and providing the basis for reinforcing three-dimensional collagen-based biomaterials in order to direct cell function and mediate mechanotransduction.

Foot massage versus quiet presence on agitation and mood in people with dementia : a randomised controlled trial

Background There is increasing interest in using complementary and alternative treatments to manage behavioural and psychological symptoms of dementia such as agitation, aggression and depressed mood. Objective To compare the effect of foot massage (intervention) and quiet presence (control) on agitation and mood in people with dementia. Design A randomised controlled trial using a within-subjects, crossover design. Settings Five long-term care facilities in Brisbane, Australia. The primary outcome was the Cohen-Mansfield Agitation Inventory (CMAI) and the secondary outcome was the Observed Emotion Rating Scale (OERS). The screening and data collection research assistants, families, and care staff were blinded to participant allocation. Participants Participants of the study were 55 long-term care residents aged 74–103 years (mean age 86.5), with moderate to severe dementia and a history of agitated behaviour according to the Pittsburgh Agitation Scale. A computer-program randomised participants to 10-min foot massage (intervention) or quiet presence (control), every weekday for 3 weeks. Results A carry-over effect was identified in the data, and so the data was treated as a parallel groups RCT. The mean total CMAI increased in both groups (reflecting an increase in agitation) with this increase greater in the quiet presence group than the foot massage group (p=0.03). There was a trend towards a difference on OERS General Alertness, with a positive change in alertness for participants in the foot massage group (indicating reduced alertness) and a negative change for participants in the quiet presence group (indicating increased alertness) (F(1,51)=3.88, p=0.05, partial ή2=0.07). Conclusions The findings highlight the need for further research on the specific conditions under which massage might promote relaxation and improve mood for people with dementia. The unfamiliar research assistants and variations in usual activity may have contributed to the increase in agitation and this needs further research.

Foot massage and physiological stress in people with dementia : a randomized controlled trial

Background There is increasing interest in using complementary and alternative treatments to manage behavioural and psychological symptoms of dementia such as agitation, aggression and depressed mood. Objective To compare the effect of foot massage (intervention) and quiet presence (control) on agitation and mood in people with dementia. Design A randomised controlled trial using a within-subjects, crossover design. Settings Five long-term care facilities in Brisbane, Australia. The primary outcome was the Cohen-Mansfield Agitation Inventory (CMAI) and the secondary outcome was the Observed Emotion Rating Scale (OERS). The screening and data collection research assistants, families, and care staff were blinded to participant allocation. Participants Participants of the study were 55 long-term care residents aged 74–103 years (mean age 86.5), with moderate to severe dementia and a history of agitated behaviour according to the Pittsburgh Agitation Scale. A computer-program randomised participants to 10-min foot massage (intervention) or quiet presence (control), every weekday for 3 weeks. Results A carry-over effect was identified in the data, and so the data was treated as a parallel groups RCT. The mean total CMAI increased in both groups (reflecting an increase in agitation) with this increase greater in the quiet presence group than the foot massage group (p=0.03). There was a trend towards a difference on OERS General Alertness, with a positive change in alertness for participants in the foot massage group (indicating reduced alertness) and a negative change for participants in the quiet presence group (indicating increased alertness) (F(1,51)=3.88, p=0.05, partial ή2=0.07). Conclusions The findings highlight the need for further research on the specific conditions under which massage might promote relaxation and improve mood for people with dementia. The unfamiliar research assistants and variations in usual activity may have contributed to the increase in agitation and this needs further research.

Exploring the effect of aquatic exercise on behaviour and psychological wellbeing in people with moderate to severe dementia : a pilot study of the Watermemories Swimming Club

Aim To explore the effects of a dementia-specific, aquatic exercise intervention on behavioural and psychological symptoms in people with dementia (BPSD). Method Residents from two aged care facilities in Queensland, Australia, received a 12-week intervention consisting of aquatic exercises for strength, agility, flexibility, balance and relaxation. The Psychological Well-Being in Cognitively Impaired Persons Scale (PW-BCIP) and the Revised Memory and Behaviour Problems Checklist (RMBPC) were completed by registered nurses at baseline, week 6, week 9 and post intervention. Results Ten women and one man (median age = 88.4 years, interquartile range = 12.3) participated. Statistically significant declines in the RMBPC and PW-BCIP were observed over the study period. Conclusion Preliminary evidence suggests that a dementia-specific, aquatic exercise intervention reduces BPSD and improves psychological well-being in people with moderate to severe dementia. With further testing, this innovative intervention may prove effective in addressing some of the most challenging aspects of dementia care.

The Watermemories Swimming Club

This pilot project aimed to try something different - rekindle positive memories of swimming in people with dementia who enjoyed swimming throughout their lives, and involve them in active swimming again using a swimming club intervention. Club members were recruited from two residential aged care facilities in Queensland, Australia (n=25 recruited, n=18 commenced, n=11 (median age=88.4, IQR=12.3; 1 male) completed the intervention). The 12 week program consisted of two, 45 minute sessions per week held at a municipal pool, using a trained instructor and assistants. Measures, taken at baseline, Week 6, Week 9 and post intervention included psychosocial and physical assessments such as the Revised Memory and Behavior Problems Checklist, Psychological Well-Being in Cognitively Impaired Persons, Seniors Physical Performance Battery and bioelectric impedance analysis. Stakeholder focus groups determined the barriers and facilitators for the club. Three outcomes have been achieved: 1) the development of a dementia specific, evidence-based, aquatic exercise program. This valuable resource will ensure that the benefits will be maximized with tailored exercises for strength, agility, flexibility, balance, relaxation and stress reduction, 2) improved quality of life for members, with statistically significant improvements in psychological wellbeing (χ2 =8.66, p<0.05), BPSD expression (χ2=16.91, p=0.001) and staff distress (χ2=16.86, p=0.001) and 3) an informative website with instructional video clips and a manual to assist others in implementing and maintaining a Watermemories Swimming Club. This pilot project has provided strong evidence that aquatic exercise can produce positive physical, psychosocial and behavioral outcomes for people with dementia.

Sterilizing tissue-materials using pulsed power plasma

This paper investigates the potential of pulsed power to sterilize hard and soft tissues and its impact on their physico-mechanical properties. It hypothesizes that pulsed plasma can sterilize both vascular and avascular tissues and the transitive layers in between without deleterious effects on their functional characteristics. Cartilage/bone laminate was chosen as a model to demonstrate the concept, treated at low temperature, at atmospheric pressure, in short durations and in buffered environment using a purposed-built pulsed power unit. Input voltage and time of exposure were assigned as controlling parameters in a full factorial design of experiment to determine physical and mechanical alteration pre- and post-treatment. The results demonstrated that, discharges of 11 kV sterilized samples in 45 s, reducing intrinsic elastic modules from 1.4 ± 0.9 to 0.9 ± 0.6 MPa. There was a decrease of 14.1 % in stiffness and 27.8 % in elastic-strain energy for the top quartile. Mechanical impairment was directly proportional to input voltage (P value < 0.05). Bacterial inactivation was proportional to treatment time for input voltages above 32 V (P < 0.001; R Sq = 0.98). Thermal analysis revealed that helix-coil transition decelerated with exposure time and collagen fibrils were destabilized as denaturation enthalpy reduced by 200 μV. We concluded by presenting a safe operating threshold for pulsed power plasma as a feasible protocol for effective sterilization of connective tissues with varying level of loss in mechanical robustness which we argue to be acceptable in certain medical and tissue engineering application.

Total heat transfer measurements on a flight investigation of reentry environment model

Stagnation-point total heat transfer was measured on a 1:27.7 model of the Flight Investigation of Reentry Environment II flight vehicle. Experiments were performed in the X1 expansion tube at an equivalent flight velocity and static enthalpy of 11 km/s and 12.7 MJ/kg, respectively. Conditions were chosen to replicate the flight condition at a total flight time of 1639.5 s, where radiation contributed an estimated 17-36% of the total heat transfer. This contribution is theorized to reduce to <2% in the scaled experiments, and the heating environment on the test model was expected to be dominated by convection. A correlation between reported flight heating rates and expected experimental heating, referred to as the reduced flight value, was developed to predict the level of heating expected on the test model. At the given flow conditions, the reduced flight value was calculated to be 150 MW/m2. Average stagnation-point total heat transfer was measured to be 140 ± 7% W/m2, showing good agreement with the predicted value. Experimentally measured heat transfer was found to have good agreement of between 5 and 15% with a number of convective heating correlations, confirming that convection dominates the tunnel heating environment, and that useful experimental measurements could be made in weakly coupled radiating flow

Numerical study of lid-driven square cavity with heat generation using LBM

In this study, the mixed convection heat transfer and fluid flow behaviors in a lid-driven square cavity filled with high Prandtl number fluid (Pr = 5400, ν = 1.2×10-4 m2/s) at low Reynolds number is studied using thermal Lattice Boltzmann method (TLBM) where ν is the viscosity of the fluid. The LBM has built up on the D2Q9 model and the single relaxation time method called the Lattice-BGK (Bhatnagar-Gross-Krook) model. The effects of the variations of non dimensional mixed convection parameter called Richardson number(Ri) with and without heat generating source on the thermal and flow behavior of the fluid inside the cavity are investigated. The results are presented as velocity and temperature profiles as well as stream function and temperature contours for Ri ranging from 0.1 to 5.0 with other controlling parameters that present in this study. It is found that LBM has good potential to simulate mixed convection heat transfer and fluid flow problem. Finally the simulation results have been compared with the previous numerical and experimental results and it is found to be in good agreement.

Investigation on Temperature-Dependent Electrical Conductivity of Carbon Nanotube/Epoxy Composites for Sustainable Energy Applications

Composites with carbon nanotubes are becoming increasingly used in energy storage and electronic devices, due to incorporated excellent properties from carbon nanotubes and polymers. Although their properties make them more attractive than conventional smart materials, their electrical properties are found to be temperature-dependent which is important to consider for the design of devices. To study the effects of temperature in electrically conductive multi-wall carbon nanotube/epoxy composites, thin films were prepared and the effect of temperature on the resistivity, thermal properties and Raman spectral characteristics of the composite films was evaluated. Resistivity-temperature profiles showed three distinct regions in as-cured samples and only two regions in samples whose thermal histories had been erased. In the vicinity of the glass transition temperature, the as-cured composites exhibited pronounced resistivity and enthalpic relaxation peaks, which both disappeared after erasing the composites’ thermal histories by temperature cycling. Combined DSC, Raman spectroscopy, and resistivity-temperature analyses indicated that this phenomenon can be attributed to the physical aging of the epoxy matrix and that, in the region of the observed thermal history-dependent resistivity peaks, structural rearrangement of the conductive carbon nanotube network occurs through a volume expansion/relaxation process. These results have led to an overall greater understanding of the temperature-dependent behaviour of conductive carbon nanotube/epoxy composites, including the positive temperature coefficient effect.

Development of polymers for Non-CAR resists for EUV lithography

Three strategies for approaching the design and synthesis of non-chemically amplified resists (non-CARs) are presented. These are linear polycarbonates, star polyester-blk-poly(methyl methacrylate) and comb polymers with polysulfone backbones. The linear polycarbonates were designed to cleave when irradiated with 92 eV photons and high Tg alicyclic groups were incorporated into the backbone to increase Tg and etch resistance. The star block copolymers were designed to have a core that is sensitive to 92 eV photons and arms that have the potential to provide properties such as high Tg and etch resistance. Similarly the polysulfone comb polymers were designed to have an easily degradable polymer backbone and comb-arms that impart favorable physical properties. Initial patterning results are presented for a number of the systems.

Numerical modelling of porous injection in a radical farming scramjet

A numerical investigation of the behaviour of fuel injection through a porous surface in an inlet-fuelled, radial-farming scramjet is presented. The performance of porous fuel injection is compared to discrete port hole injection at an equivalence ratio of φ ≈ 0.4 for both cases. The comparison is performed at a Mach 6.5 flow condition with a total specific enthalpy of 4.3 MJ/kg. The numerical results are compared to experiments performed in the T4 shock tunnel where available. The presented results demonstrate for the first time, that porous fuel injection has the potential to outperform port hole injectors in scramjet engines in terms of fuel-air mixing, ignition delays and achievable combustion efficiencies despite reduced fuel penetration heights.

H2-O2 porous fuel injection in a radical farming scramjet

This paper reports on the experimental testing of oxygen compatible ceramic matrix composite porous injectors in a nominally two-dimensional hydrogen fuelled and oxygen enriched radical farming scramjet in the T4 shock tunnel facility. All experiments were performed at a dynamic pressure of 146 kPa, an equivalent flight Mach number of 9.7, a stagnation pressure and enthalpy of 40MPa and 4.3 MJ/kg respectively and at a fuelling condition that resulted in an average equivalence ratio of 0.472. Oxygen was pre-mixed with the fuel prior to injection to achieve enrichment percentages of approximately 13%, 15% and 17%. These levels ensured that the hydrogen-oxidiser mix injected into the engine always remained too fuel rich to sustain a flame without any additional mixing with the captured air. Addition of pre-mixed oxygen with the fuel was found to significantly alter the performance of the engine; enhancing both combustion and ignition and converting a previously observed limited combustion condition into one with sustained and noticeable combustion induced pressure rise. Increases in the enrichment percentage lead to further increases in combustion levels and acted to reduce ignition lengths within the engine. Suppressed combustion runs, where a nitrogen test gas was used, confirmed that the pressure rise observed in these experiments as attributed to the oxygen enrichment and not associated with the increased mass injected.

A detailed investigation of nominally 2-D radical-farming scramjet combustion

This paper reports on an investigation of the flow/chemistry coupling inside a nominally two-dimensional inlet-fuelled scramjet configuration. The experiments were conducted at a freestream Mach number of 7.3 and a total flow enthalpy of 4.3MJ/kg corresponding to a Mach 9.7 flight condition. The phenomenon of radical-farming has been studied in detail using two-dimensional OH* chemiluminescence imaging and emission spectroscopy. High signal levels of excited OH (OH*) were detected behind the first shock reflections inside the combustion chamber upstream of any measurable pressure rise from combustion, which occurred towards the rear of the combustor. The production of OH in the first hot pocket initiates the ignition process and then accelerates the combustion process in the next downstream hot pocket. This was confirmed by numerical simulations of premixed hydrogen/air flow through the scramjet. Chemical kinetics analyses reveal that the ignition process is governed by the interaction between various reaction groups leading to a chainbranching explosion for low mean temperature and pressure combustion flowfields.

Analysis of strain-rate dependent mechanical behavior of single chondrocyte : a finite element study

Various studies have been conducted to investigate the effects of impact loading on cartilage damage and chondrocyte death. These have shown that the rate and magnitude of the applied strain significantly influence chondrocyte death, and that cell death occurred mostly in the superficial zone of cartilage suggesting the need to further understand the fundamental mechanisms underlying the chondrocytes death induced at certain levels of strain-rate. To date there is no comprehensive study providing insight on this phenomenon. The aim of this study is to examine the strain-rate dependent behavior of a single chondrocyte using a computational approach based on Finite Element Method (FEM). An FEM model was developed using various mechanical models, which were Standard Neo-Hookean Solid (SnHS), porohyperelastic (PHE) and poroviscohyperelastic (PVHE) to simulate Atomic Force Microscopy (AFM) experiments of chondrocyte. The PVHE showed, it can capture both relaxation and loading rate dependent behaviors of chondrocytes, accurately compared to other models.