Modified Stranski–Krastanov growth in Ge/Si heterostructures via nanostenciled pulsed laser deposition

The combination of nanostenciling with pulsed laser deposition (PLD) provides a flexible, fast approach for patterning the growth of Ge on Si. Within each stencilled site, the morphological evolution of the Ge structures with deposition follows a modified Stranski–Krastanov (SK) growth mode. By systematically varying the PLD parameters (laser repetition rate and number of pulses) on two different substrate orientations (111 and 100), we have observed corresponding changes in growth morphology, strain and elemental composition using scanning electron microscopy, atomic force microscopy and μ-Raman spectroscopy. The growth behaviour is well predicted within a classical SK scheme, although the Si(100) growth exhibits significant relaxation and ripening with increasing coverage. Other novel aspects of the growth include the increased thickness of the wetting layer and the kinetic control of Si/Ge intermixing via the PLD repetition rate.

Reduced graphene oxide growth on 316L stainless steel for medical applications

We report a new method for the growth of reduced graphene oxide (rGO) on the 316L alloy of stainless steel (SS) and its relevance for biomedical applications. We demonstrate that electrochemical etching increases the concentration of metallic species on the surface and enables the growth of rGO. This result is supported through a combination of Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), scanning electron microscopy (SEM), density functional theory (DFT) calculations and static water contact angle measurements. Raman spectroscopy identifies the G and D bands for oxidized species of graphene at 1595 cm(-1) and 1350 cm(-1), respectively, and gives an ID/IG ratio of 1.2, indicating a moderate degree of oxidation. XPS shows -OH and -COOH groups in the rGO stoichiometry and static contact angle measurements confirm the wettability of rGO. SEM and AFM measurements were performed on different substrates before and after coronene treatment to confirm rGO growth. Cell viability studies reveal that these rGO coatings do not have toxic effects on mammalian cells, making this material suitable for biomedical and biotechnological applications.

Synthesis, characterization, and electronic structure studies of cubic Bi1.5ZnTa1.5O7 for photocatalytic applications

Bi1.5ZnTa1.5O7 (BZT) has been synthesized using an alkoxide based sol-gel reaction route. The evolution of the phases produced from the alkoxide precursors and their properties have been characterized as function of temperature using a combination of thermogravimetric analysis (TGA) coupled with mass spectrometry (MS), infrared emission spectrometry (IES), X-ray diffraction (XRD), ultraviolet and visible (UV-Vis) spectroscopy, Raman spectroscopy, and N2 adsorption/desorption isotherms. The lowest sintering temperature (600∘C) to obtain phase pure BZT powders with high surface area (14.5m2/g) has been determined from the thermal decomposition and phase analyses.The photocatalytic activity of the BZT powders has been tested for the decolorization of organic azo-dye and found to be photoactive under UV irradiation.The electronic band structure of the BZT has been investigated using density functional theory (DFT) calculations to determine the band gap energy (3.12 eV) and to compare it with experimental band gap (3.02 eV at 800∘C) from optical absorptionmeasurements. An excellent match is obtained for an assumption of Zn cation substitutions at specifically ordered sites in the BZT structure.

Simple Method of Preparing Graphene Flakes by an Arc-Discharge Method

Arc discharge between graphite electrodes under a relatively high pressure of hydrogen yields graphene flakes generally containing 2-4 layers in the inner wall region of the arc chamber. The graphene flakes so obtained have been characterized by X-ray diffraction, atomic force microscopy, transmission electron microscopy, and Raman spectroscopy. The method is eminently suited to dope graphene with boron and nitrogen by carrying out arc discharge in the presence of diborane and pyridine respectively.

Graphene, the new nanocarbon

Graphene is a fascinating new nanocarbon possessing, single-, bi- or few- (<= ten) layers of carbon atoms forming six-membered rings. Different types of graphene have been investigated by X-ray diffraction, atomic force microscopy, transmission electron microscopy, scanning tunneling microscopy and Raman spectroscopy. The extraordinary electronic properties of single-and bi-layer graphenes are indeed most unique and unexpected. Other properties of graphene such as gas adsorption characteristics, magnetic and electrochemical properties and the effects of doping by electrons and holes are equally noteworthy. Interestingly, molecular charge-transfer also markedly affects the electronic structure and properties of graphene. Many aspects of graphene are yet to be explored, including synthetic strategies which can yield sufficient quantities of graphene with the desired number of layers.

From Polymorph Screening to Dissolution Testing - Solid Phase Analysis during Pharmaceutical Development and Manufacturing

Solid materials can exist in different physical structures without a change in chemical composition. This phenomenon, known as polymorphism, has several implications on pharmaceutical development and manufacturing. Various solid forms of a drug can possess different physical and chemical properties, which may affect processing characteristics and stability, as well as the performance of a drug in the human body. Therefore, knowledge and control of the solid forms is fundamental to maintain safety and high quality of pharmaceuticals. During manufacture, harsh conditions can give rise to unexpected solid phase transformations and therefore change the behavior of the drug. Traditionally, pharmaceutical production has relied on time-consuming off-line analysis of production batches and finished products. This has led to poor understanding of processes and drug products. Therefore, new powerful methods that enable real time monitoring of pharmaceuticals during manufacturing processes are greatly needed. The aim of this thesis was to apply spectroscopic techniques to solid phase analysis within different stages of drug development and manufacturing, and thus, provide a molecular level insight into the behavior of active pharmaceutical ingredients (APIs) during processing. Applications to polymorph screening and different unit operations were developed and studied. A new approach to dissolution testing, which involves simultaneous measurement of drug concentration in the dissolution medium and in-situ solid phase analysis of the dissolving sample, was introduced and studied. Solid phase analysis was successfully performed during different stages, enabling a molecular level insight into the occurring phenomena. Near-infrared (NIR) spectroscopy was utilized in screening of polymorphs and processing-induced transformations (PITs). Polymorph screening was also studied with NIR and Raman spectroscopy in tandem. Quantitative solid phase analysis during fluidized bed drying was performed with in-line NIR and Raman spectroscopy and partial least squares (PLS) regression, and different dehydration mechanisms were studied using in-situ spectroscopy and partial least squares discriminant analysis (PLS-DA). In-situ solid phase analysis with Raman spectroscopy during dissolution testing enabled analysis of dissolution as a whole, and provided a scientific explanation for changes in the dissolution rate. It was concluded that the methods applied and studied provide better process understanding and knowledge of the drug products, and therefore, a way to achieve better quality.

Conformational analysis of small disulfide loops. Spectroscopic and theoretical studies on a synthetic cyclic tetrapeptide containing cystine

The conformational analysis of the synthetic peptide Boc-Cys-Pro-Val-Cys-NHMe has been carried out, as a model for small disulfide loops, in biologically active polypeptides. 'H NMR studies (270 MHz) establish that the Val(3) and Cys(4) NH groups are solvent shielded, while 13C studies establish an all-trans peptide backbone. Circular dichroism and Raman spectroscopy provide evidence for a right-handed twist of the disulfide bond. Analysis of the vicinal (JaB)c oupling constants for the two Cys residues establishes that XI - *60° for Cys(4), while some flexibility is suggested at Cys( 1). Conformational energy calculations, imposing intramolecular hydrogen bonding constraints, favor a P-turn (type I) structure with Pro(2)-Va1(3) as the corner residues. Theoretical and spectroscopic results are consistent with the presence of a transannular 4 - 1 hydrogen bond between Cys( 1) CO and Cys(4) NH groups, with the Val NH being sterically shielded from the solvent environment.

Historical review of light scattering studies

This paper reviews the earlier experimental studies on light scattering in quartz near its phase transition, which ultimately laid the foundation for the basic concept of the soft mode. The theoretical work on the subject has been briefly referred to. A list of ferroelectrics in which soft mode studies have been carried out near TC using laser Raman spectroscopy is appended. Reference has also been made to the appearance of the central mode with abnormal increase in intensity at TC.

Vibrational spectroscopic studies of the ferroelectric LiRbSO4

Lithium rubidium sulphate, LiRbSO4 (LRS), undergoes a sequence of four phase transitions at 166, 185, 202 and 204°C. The phase between 202 and 204°C is incommensurate. Polarized phonon Raman spectra in the frequency region of 50-1200 cm-1 are presented to identify the external and internal vibrational modes at room temperature. The internal mode frequencies of the sulphate ions are presented in the temperature region from -150 to 230°C covering all the phase transitions. The total integrated areas of the 1, 2 and 4 modes show an anomalous increase across the phase transitions. The frequencies of the symmetric stretching (1) and symmetric bending (2) modes do not show any changes at the phase transitions, but the width of the 2 mode shows changes across the phase transitions. A small increase in the linewidth of the 2 mode observed in the incommensurate phase is attributed to the influence of the incommensurate modulation wave. A DSC thermogram showed endothermic peaks during heating at all the phase transitions. The IR spectrum recorded at room temperature showed the expected Au and Bu internal modes.

Mechanisms of molecular doping of graphene: A first-principles study

Doping graphene with electron donating or accepting molecules is an interesting approach to introduce carriers into it, analogous to electrochemical doping accomplished in graphene when used in a field-effect transistor. Here, we use first-principles density-functional theory to determine changes in the electronic-structure and vibrational properties of graphene that arise from the adsorption of aromatic molecules such as aniline and nitrobenzene. Identifying the roles of various mechanisms of chemical interaction between graphene and a molecule, we bring out the contrast between electrochemical and molecular doping of graphene. Our estimates of various contributions to shifts in the Raman-active modes of graphene with molecular doping are fundamental to the possible use of Raman spectroscopy in (a) characterization of the nature and concentration of carriers in graphene with molecular doping, and (b) graphene-based chemical sensors.

Phthalocyanine macrocycle as stabilizer for gold and silver nanoparticles

A one-step process was used for the preparation of gold and silver nanoparticles stabilized by an aminophthalocyanine macrocycle. The resultant nanoparticles were characterized by absorption spectra, infrared spectroscopy, scanning electron microscopy and transmission electron microscopy. The nanoparticles were found to possess relatively narrow size distribution. The gold nanoparticles have an average diameter of similar to 2 nm, while silver particles have 4-5 nm. Preliminary studies on fluorescence and surface enhanced Raman spectroscopy were carried out using these nanoparticles. Fluorescence studies indicate that gold nanoparticles do not quench the fluorescence, while silver nanoparticles do. The stabilized nanoparticles showed enhancement of the Raman signals, thus revealing that they are good substrates for surface enhanced Raman scattering studies.

Synthesis of liquid crystalline benzothiazole base derivatives: A study of their optical and electrical properties

Two new donor-acceptor type liquid crystalline semiconductors based on benzothiazole have been synthesized. Their structural, photophysical and electronic properties were investigated using X-ray diffraction, atomic force microscopy, cyclic voltammetry, UV-Vis, photoluminescence, and Raman spectroscopy. The liquid crystalline behaviour of the molecules was thoroughly examined by differential scanning calorimetry (DSC) and optical polarizing microscope. The DSC and thermogravimetric analysis (TGA) show that these materials posses excellent thermal stability and have decomposition temperatures in excess of 300 degrees C. Beyond 160 degrees C both molecules show a smectic A liquid crystalline phase that exists till about 240 degrees C. Field-effect transistors were fabricated by vacuum evaporating the semiconductor layer using standard bottom gate/top contact geometry. The devices exhibit p-channel behaviour with hole mobilities of 10(-2) cm(2)/Vs. (C) 2009 Elsevier B.V. All rights reserved.

A one-step technique to prepare aligned arrays of carbon nanotubes

A simple effective pyrolysis technique has been developed to synthesize aligned arrays of multi-walled carbon nanotubes (MWCNTs) without using any carrier gas in a single-stage furnace at 700 °C. This technique eliminates nearly the entire complex and expensive machinery associated with other extensively used methods for preparation of CNTs such as chemical vapour deposition (CVD) and pyrolysis. Carbon source materials such as xylene, cyclohexane, camphor, hexane, toluene, pyridine and benzene have been pyrolyzed separately with the catalyst source material ferrocene to obtain aligned arrays of MWCNTs. The synthesized CNTs have been characterized by scanning electron microscopy (SEM), x-ray diffraction (XRD), transmission electron microscopy (TEM), thermogravimetric analysis (TGA) and Raman spectroscopy. In this technique, the need for the tedious and time-consuming preparation of metal catalysts and continuously fed carbon source material containing carrier gas can be avoided. This method is a single-step process where not many parameters are required to be monitored in order to prepare aligned MWCNTs. For the production of CNTs, the technique has great advantages such as low cost and easy operation.

Pd and Pt ions as highly active sites for the water-gas shift reaction over combustion synthesized zirconia and zirconia-modified ceria

Noble metal substituted ionic catalysts were synthesized by solution combustion technique. The compounds were characterized by X-ray diffraction, FT-Raman spectroscopy, and X-ray photoelectron spectroscopy. Zirconia supported compounds crystallized in tetragonal phase. The solid solutions of ceria with zirconia crystallized in fluorite structure. The noble metals were substituted in ionic form.The water-gas shift reaction was carried out over the catalysts.Negligible conversions were observed with unsubstituted compounds. The substitution of a noble metal ion was found to enhance the reaction rate. Equilibrium conversion was obtained below 250 degrees C in the presence of Pt ion substituted compounds. The formation of Bronsted acid-Bronsted base pairs was proposed to explain the activity of zirconia catalysts. The effect of oxide ion vacancies on the reactions over substituted ceria-zirconia solid solutions was established. (c)2010 Elsevier B.V. All rights reserved.

Tablettien soveltuvuus annosjakeluun

Koneellinen annosjakelu on kasvava lääkehuollon osa-alue, jossa lääkkeet pakataan koneellisesti pieniin annoskertakohtaisiin pusseihin kahden viikon erissä. Aikaisemmin lääkevalmisteiden soveltuvuutta koneelliseen annosjakeluun ei ole systemaattisesti tutkittu. Tutkimus tehtiin yhteistyössä Espoonlahden apteekin annosjakeluyksikön kanssa ja sen tavoitteena oli määrittää annosjakeluprosessin kannalta optimaaliset ominaisuudet annosjaeltavalle tabletille rikkoutumisten ja siirtymien vähentämiseksi. Rikkoutuminen on lääkevalmisteen murentumista, puolittumista tai muuta rikkoutumista annosjakelun aikana. Siirtymä on lääkevalmisteen jakelu väärään annospussiin. Prosentuaalisesti rikkoutumisia ja siirtymiä on jakelumäärästä hyvin vähän, mutta määrällisesti paljon ja koko ajan enemmän koneellisen annosjakelun yleistyessä. Rikkoutumiset ja siirtymät aiheuttavat paljon lisätyötä pussien korjaamisen takia, joten niiden määrää on pyrittävä vähentämään. Lisäksi tavoitteena oli selvittää lääkkeiden valmistajilta kysyttävissä olevat asiat lääkevalmisteiden ominaisuuksista ja säilyvyydestä, jotta voitaisiin päätellä valmisteen soveltuvuus koneelliseen annosjakeluun kirjallisen tiedon perusteella. Tutkimuksen tulosten perusteella rikkoutumisten ja siirtymien vähentämiseksi optimaalinen tablettivalmiste annosjakeluun on pienehkö tai keskisuuri, päällystetty, luja ja jakouurteeton ja optimaalinen ilman suhteellinen kosteustaso annosjakeluyksikön tuotantotiloissa olisi noin 30 – 40 %. Lääkkeiden valmistajilta kysyttäviä seikkoja ovat koon, päällysteen, murtolujuuden ja jakouurteen lisäksi valmisteen säilyvyys alkuperäispakkauksen ulkopuolella sekä valmisteen valo-, lämpö- ja kosteusherkkyys. Rikkoutumisten ja siirtymien lisäksi tutkittiin myös kosteusherkän asetyylisalisyylihappovalmisteen (Disperin 100 mg) säilyvyyttä 25 °C ja 60 % RH olosuhteissa, koska tuotantotilojen ilman kosteustasoa ei ole säädelty. Säilyvyystutkimuksen kesto oli neljä viikkoa. Se on riittävä, koska se on enimmäisaika, jonka tabletit ovat annosjakeluprosessin yhteydessä pois alkuperäispakkauksestaan ennen käyttöä. Tabletteja säilytettiin avoimessa alkuperäispakkauksessa (purkki), suljetussa alkuperäispakkauksessa, annosjakelukoneen kasetissa ja kahdessa erilaisessa annospussissa (uusi ja käytössä oleva materiaali). Tulosten mukaan annosjakelukoneen kasetti suojaa kosteudelta yhtä huonosti kuin avoin purkki. Uusi pussimateriaali sen sijaan suojaa kosteudelta paremmin kuin tällä hetkellä käytössä oleva materiaali. Raman -spektroskopiamittausten perusteella asetyylisalisyylihappotableteissa ei ehdi neljän viikon seurannan aikana tapahtua asetyylisalisyylihapon hajoamista salisyylihapoksi. Kosteus heikentää tablettien murtolujuutta, mikä saattaa aiheuttaa enemmän rikkoutumisia. Kosteustaso olisi hyvä olla säädettävissä vakioksi tuotantotiloissa tai purkaa tabletit kasetteihin mahdollisimman lähellä jakelua rikkoutumisten ehkäisemiseksi, etenkin ilman kosteustason ollessa korkea. Lisäksi tutkittiin lääkevalmisteen lämpöherkkyyttä koska annosjakelukoneen saumauslaite altistaa annospussit noin 75 °C lämmölle, jos annosjakelukone pysäytetään kesken työn. Tutkimus tehtiin XRPD:llä, jolla voidaan säätää näytteen lämpötilaa. Lämpöherkkyystutkimusten perusteella 75 °C lämpö ei ehdi tunnin aikana aiheuttaa muutoksia karbamatsepiinitabletissa (Neurotol 200 mg). Tuloksista selvisi, että tutkitun valmisteen sisältämä karbamatsepiini ei kuitenkaan ole lämpöherkin muoto, joten muita lämpöherkkiä lääkevalmisteita tulisi tutkia lisätiedon saamiseksi lämmön vaikutuksista.