Design of salient pole PM synchronous machines for a vehicle traction application – Analysis and

This doctoral thesis presents a study on the development of a liquid-cooled frame salient pole permanent-magnet-exited traction machine for a four-wheel-driven electric car. The emphasis of the thesis is put on a radial flux machine design in order to achieve a light-weight machine structure for traction applications. The design features combine electromagnetic and thermal design methods, because traction machine operation does not have a strict operating point. Arbitrary load cycles and the flexible supply require special attention in the design process. It is shown that accurate modelling of the machine magnetic state is essential for high-performance operation. The saturation effect related to the cross-saturation has to be taken carefully into account in order to achieve the desired operation. Two prototype machines have been designed and built for testing: one totally enclosed machine with a special magnet module pole arrangement and another through-ventilated machine with a more traditional embedded magnet structure. Both structures are built with magnetically salient structures in order to increase the torque production capability with the reluctance torque component. Both machine structures show potential for traction usage. However, the traditional embedded magnet design turns out to be mechanically the more secure one of these two machine options.

Novel Methods for Error Modeling and Parameter Identification of a Redundant Serial-Parallel Hybrid Robot

To obtain the desirable accuracy of a robot, there are two techniques available. The first option would be to make the robot match the nominal mathematic model. In other words, the manufacturing and assembling tolerances of every part would be extremely tight so that all of the various parameters would match the “design” or “nominal” values as closely as possible. This method can satisfy most of the accuracy requirements， but the cost would increase dramatically as the accuracy requirement increases. Alternatively, a more cost-effective solution is to build a manipulator with relaxed manufacturing and assembling tolerances. By modifying the mathematical model in the controller, the actual errors of the robot can be compensated. This is the essence of robot calibration. Simply put, robot calibration is the process of defining an appropriate error model and then identifying the various parameter errors that make the error model match the robot as closely as possible. This work focuses on kinematic calibration of a 10 degree-of-freedom (DOF) redundant serial-parallel hybrid robot. The robot consists of a 4-DOF serial mechanism and a 6-DOF hexapod parallel manipulator. The redundant 4-DOF serial structure is used to enlarge workspace and the 6-DOF hexapod manipulator is used to provide high load capabilities and stiffness for the whole structure. The main objective of the study is to develop a suitable calibration method to improve the accuracy of the redundant serial-parallel hybrid robot. To this end, a Denavit–Hartenberg (DH) hybrid error model and a Product-of-Exponential (POE) error model are developed for error modeling of the proposed robot. Furthermore, two kinds of global optimization methods, i.e. the differential-evolution (DE) algorithm and the Markov Chain Monte Carlo (MCMC) algorithm, are employed to identify the parameter errors of the derived error model. A measurement method based on a 3-2-1 wire-based pose estimation system is proposed and implemented in a Solidworks environment to simulate the real experimental validations. Numerical simulations and Solidworks prototype-model validations are carried out on the hybrid robot to verify the effectiveness, accuracy and robustness of the calibration algorithms.

Detection and phylogenetic analysis of porcine enteric calicivirus, genetically related to the Cowden strain of sapovirus genogroup III, in Brazilian swine herds

Sapovirus of the Caliciviridae family is an important agent of acute gastroenteritis in children and piglets. The Sapovirus genus is divided into seven genogroups (G), and strains from the GIII, GVI and GVII are associated with infections in swine. Despite the high prevalence in some countries, there are no studies related to the presence of porcine enteric sapovirus infections in piglets in Brazil. In the present study, 18 fecal specimens from piglets up to 28 days were examined to determine the presence of sapovirus genome by RT-PCR assay, using primers designed to amplify a 331 bp segment of the RNA polymerase gene. In 44.4% (8/18) of fecal samples, an amplified DNA fragment was obtained. One of these fragments was sequenced and submitted to molecular and phylogenetic analysis. This analysis revealed high similarity, with nucleotides (87%) and amino acids (97.8%), to the Cowden strain, the GIII prototype of porcine enteric calicivirus. This is the first description of sapovirus in Brazilian swine herds.

Painesuodattimen automatisoidun kankaanvaihtolaitteen kehittäminen ja tekninen tuotteistaminen

Tässä työssä tarkastellaan CE-merkintään vaadittavia teknisen tuotteistamisen vaiheita käyttäen esimerkkinä painesuodattimen automatisoidun kankaanvaihtolaitteen suunnitteluprosessia. Työssä selvitetään, mitä vaihtoehtoja on painesuodattimen lisälaitteiden luokitteluksi, että ne saadaan tuotteistettua Euroopan talousalueella (ETA). Esimerkkinä käytettävä kankaanvaihtolaite on suunniteltu käyttäen järjestelmällisen koneensuunnittelun menetelmää. CE-merkinnän vaatima riskianalyysi on tehty laitteelle standardin SFS-EN ISO 12100:2010 mukaisesti. Tuloksena saatu laitteen prototyyppi täyttää pääosin laitteelle asetettavat vaatimukset. Kustannusarvio ylittää kuitenkin toivotun omakustannehinnan valoverhojen suhteellisen kalliin hinnan takia. Kustannusarvion mukaan prototyyppi voidaan kuitenkin valmistaa edullisesti, sillä valoverhot eivät ole pakollisia laitteen toiminnallisissa testeissä. Ennen tuotteistamista valoverhojen korvaamisen mahdollisuutta muulla turvatekniikalla on kuitenkin tutkittava. Suunnitteluvaiheen jälkeen laitteen turvallisuuden voidaan todeta olevan vähintään riittävällä tasolla. Riskianalyysi on kuitenkin päivitettävä dokumentti, ja laitteen turvallisuus täytyy varmistaa prototyyppiä testaamalla. Työn perusteella voidaan todeta, että huomioimalla laitteen mahdollisesti aiheuttamat vaaratilanteet jo tuotesuunnittelun alussa, voidaan tuotekehitysprosessia nopeuttaa. Tunnistamalla vaaratilanteet suunnittelun varhaisessa vaiheessa voidaan vähentää riskien määrää, ja siten tarvetta riskien pienentämiselle. Näin vähennetään rakenteen suunnittelun ja riskianalyysin iterointikierrosten määrää, jolloin myös tuotteistamisprosessi nopeutuu.

Sähköavusteisen polkupyörän energian talteenotto lineaarigeneraattorilla

Sähköavusteisten polkupyörien määrä on kasvussa. Kasvua hidastavana tekijänä voidaan pitää niiden keskimäärin yli 1000 euron hintaa, josta suurin osa johtuu akustosta. Tämän työn tarkoituksena on selvittää lineaarigeneraattorin hyödynnettävyyttä sähköavusteisissa polkupyörissä. Lisäksi työssä kuvataan vaiheittain prototyypin suunnittelu ja rakentaminen. Mikäli lineaarigeneraattori-avusteisella sähköpolkupyörällä saavutetaan huomattava pidennys toimintamatkaan, voidaan pyörät varustaa halvemmilla ja kapasiteetiltään pienemmillä akuilla. Lineaarigeneraattorin hankintaa kannustaisi se, että se maksaisi vähemmän kuin vaihto suurempikapasiteettiseen akustoon.

PV-1: Leukocyte trafficking molecule and vascular marker

The distinction between lymphatic vessels and blood vessels is a crucial factor in many studies in immunology, vascular biology and cancer biology. They both share several characteristics and perform related, though different functions. They are equally important for the performance of the human immune system with the continuous recirculation of leukocytes from the tissues via lymphatics to the blood vessels and back into the tissue presenting the link between both systems. This study was undertaken to elucidate the differences in the gene expression between primary blood- and lymphatic endothelial cells as well as the two immortalized cell lines HMEC-1 (human microvascular endothelial cell line 1) and TIME (telomerase immortalized microvascular endothelial cell line). Furthermore, we wanted to investigate the mystery surrounding the identity of the antigen recognized by the prototype blood vascular marker PAL-E. In the last step we wanted to study whether the PAL-E antigen would be involved in the process of leukocyte migration from the bloodstream into the surrounding tissue. Our results clearly show that the gene expression in primary blood endothelial cells (BEC), lymphatic endothelial cells (LEC) and the cell lines HMEC-1 and TIME is plastic. Comparison of a large set of BEC- and LEC datasets allowed us to assemble a catalog of new, stable BEC- or LEC specific markers, which we verified in independent experiments. Additionally, several lines of evidence demonstrated that PAL-E recognizes plasmalemma vesicle associated protein 1 (PV-1), which can form complexes with vimentin and neuropilin-1. Finally, numerous in vitro and in vivo experiments identify the first function of the protein PV-1 during leukocyte trafficking, where it acts as regulatory molecule.

Maastotyökoneen ajomoottorin hybridisointiin soveltuvan napavaihteiston dynamiikan mallinnus.

Työn tavoitteena oli mallintaa maastotyökoneen ajomoottorin hybridisointiin soveltuvan napavaihteiston dynamiikka. Työ tehtiin osana Saimaan ammattikorkeakoulun tutkimusprojektia, jonka tarkoituksena oli ajomoottorin ja integroidun napavaihteiston kaupallistaminen maastotyökoneisiin. Maastotyökoneena simulointimallissa käytettiin tyypillistä maataloustraktoria, johon kytkettiin vielä peräkärry. Traktorin renkaiden napaan oli kytketty ajomoottorina toimiva sähkömoottori, jonka sisään simuloitu napavaihteisto oli integroitu. Napavaihteiston dynamiikan mallintamiseen käytettiin monikappaledynamiikan simulointiohjelmistoa (Adams). Ohjelmalle määritettiin napavaihteiston komponenttien parametrit, joista voitiin simuloida vaihteiston dynaaminen käyttäytyminen. Simuloidusta mallista saatiin kytkimiin kohdistuvat voimat kytkentätilanteessa sekä sähkömoottorin väännön suunnanvaihtotilanteessa eri akselin pituuksilla, eri kytkinten nopeuseroilla, eri traktorin painoilla ja eri kuormilla ajettaessa. Mallissa simuloitiin myös sähkömoottorin käyttäytyminen vaihteenvaihtotilanteessa eri pyörimisnopeuden säätimen kertoimilla. Työssä huomattiin, että akselin mitoituksella voitiin vaikuttaa vaihteistossa ilmeneviin voimiin kytkimen kytkentähetkellä. Myös kytkimen hammastuksessa olevalla hammasvälyksellä voitiin vaikuttaa kytkimiin kohdistuviin voimiin suunnanvaihtotilanteissa. Vaihteistoon kohdistuvista voimista voidaan jatkossa suunnitella kytkimen ja akselin profiili, jotta vaihteisto kestää siihen kohdistuvat voimat.

Numerical and experimental investigation of thermal louvers for space applications

Thermal louvers, using movable or rotating shutters over a radiating surface, have gained a wide acceptance as highly efficient devices for controlling the temperature of a spacecraft. This paper presents a detailed analysis of the performance of a rectangular thermal louver with movable blades. The radiative capacity of the louver, determined by its effective emittance, is calculated for different values of the blades opening angle. Experimental results obtained with a prototype of a spacecraft thermal louver show good agreement with the theoretical values.

Single axis controlled attraction type magnetic bearing

This paper presents a new type of magnetic bearing with active control only in axial direction. The bearing uses two pairs of permanent magnets working in attraction mode to restrict the radial motion and a control system composed of two electromagnets, a gap sensor and a controller to keep the axis in a fixed axial position. The principle, the dynamic model for axial motion and the control system for this bearing are presented. Finally, by experiments conducted in a prototype, the effectiveness of the presented concept is shown.

Talousveden tuotannon ja jakelun tietohuollon kehittäminen julkisomisteisessa vesilaitoksessa

Vesilaitokset kuluttavat merkittäviä määriä energiaa, johon on alettu kiinnittää huomiota viime vuosina. Energiatehokkuuden edistämisen hidasteeksi on noussut puutteellinen tietohuolto sekä vesilaitosten yhteisten tunnuslukujen ja kriteerien puuttuminen. Diplomityön tavoitteena on selvittää tietohuollon ongelmia Tampereen Vedellä. Työn tavoitteena on myös tutkia veden tuotannon ja jakelun energiatehokkaiden ohjaustapojen löytämistä tietohuollon ja tunnuslukujen avulla. Työssä käytetyt metodologiat ovat Tampereen Veden työntekijöiden haastattelut, prototyypin analysointi sekä vedenottamoiden ominaisenergiaan liittyvien mittauspisteiden läpikäynti. Diplomityön tuloksena saatiin laaja kuva Tampereen Veden tietohuoltoon liittyvistä ongelmista. Merkittävimmät tietohuollon haasteet liittyvät työntekijöihin, järjestelmiin sekä mittauspisteiden puuttumiseen. Mittauspisteet ja niiden tallentuminen ovat edellytys tunnuslukujen luomiselle. Tunnuslukuja voidaan hyödyntää energiatehokkaiden ohjaustapojen löytämiseksi, mutta vesilaitosten yhteiset kriteerit tunnusluvuille puuttuvat. Energiatehokkuustunnuslukuja on tarve tutkia lisää ja kehittää yhteistyötä vesilaitosten välillä tunnuslukujen luomiseksi sekä vertailutietojen saamiseksi.

Design and implementation of a peer-to-peer client for device management

The aim of this master’s thesis was to specify a system requiring minimal configuration and providing maximal connectivity in the vein of Skype but for device management purposes. As peer-to-peer applications are pervasive and especially as Skype is known to provide this functionality, the research was focused on these technologies. The resulting specification was a hybrid of a tiered hierarchical network structure and a Kademlia based DHT. A prototype was produced as a proof-of-concept for the hierarchical topology, demonstrating that the specification was feasible.

Design and testing of an armature-reaction-compensated permanent magnet synchronous generator for island operation

At present, permanent magnet synchronous generators (PMSGs) are of great interest. Since they do not have electrical excitation losses, the highly efficient, lightweight and compact PMSGs equipped with damper windings work perfectly when connected to a network. However, in island operation, the generator (or parallel generators) alone is responsible for the building up of the network and maintaining its voltage and reactive power level. Thus, in island operation, a PMSG faces very tight constraints, which are difficult to meet, because the flux produced by the permanent magnets (PMs) is constant and the voltage of the generator cannot be controlled. Traditional electrically excited synchronous generators (EESGs) can easily meet these constraints, because the field winding current is controllable. The main drawback of the conventional EESG is the relatively high excitation loss. This doctoral thesis presents a study of an alternative solution termed as a hybrid excitation synchronous generator (HESG). HESGs are a special class of electrical machines, where the total rotor current linkage is produced by the simultaneous action of two different excitation sources: the electrical and permanent magnet (PM) excitation. An overview of the existing HESGs is given. Several HESGs are introduced and compared with the conventional EESG from technical and economic points of view. In the study, the armature-reaction-compensated permanent magnet synchronous generator with alternated current linkages (ARC-PMSG with ACL) showed a better performance than the other options. Therefore, this machine type is studied in more detail. An electromagnetic design and a thermal analysis are presented. To verify the operation principle and the electromagnetic design, a down-sized prototype of 69 kVA apparent power was built. The experimental results are demonstrated and compared with the predicted ones. A prerequisite for an ARC-PMSG with ACL is an even number of pole pairs (p = 2, 4, 6, …) in the machine. Naturally, the HESG technology is not limited to even-pole-pair machines. However, the analysis of machines with p = 3, 5, 7, … becomes more complicated, especially if analytical tools are used, and is outside the scope of this thesis. The contribution of this study is to propose a solution where an ARC-PMSG replaces an EESG in electrical power generation while meeting all the requirements set for generators given for instance by ship classification societies, particularly as regards island operation. The maximum power level when applying the technology studied here is mainly limited by the economy of the machine. The larger the machine is, the smaller is the efficiency benefit. However, it seems that machines up to ten megawatts of power could benefit from the technology. However, in low-power applications, for instance in the 500 kW range, the efficiency increase can be significant.

Development of a process for the direct synthesis of hydrogen peroxide in a novel microstructured reactor

Microreactors have proven to be versatile tools for process intensification. Over recent decades, they have increasingly been used for product and process development in chemical industries. Enhanced heat and mass transfer in the reactors due to the extremely high surfacearea- to-volume ratio and interfacial area allow chemical processes to be operated at extreme conditions. Safety is improved by the small holdup volume of the reactors and effective control of pressure and temperature. Hydrogen peroxide is a powerful green oxidant that is used in a wide range of industries. Reduction and auto-oxidation of anthraquinones is currently the main process for hydrogen peroxide production. Direct synthesis is a green alternative and has potential for on-site production. However, there are two limitations: safety concerns because of the explosive gas mixture produced and low selectivity of the process. The aim of this thesis was to develop a process for direct synthesis of hydrogen peroxide utilizing microreactor technology. Experimental and numerical approaches were applied for development of the microreactor. Development of a novel microreactor was commenced by studying the hydrodynamics and mass transfer in prototype microreactor plates. The prototypes were designed and fabricated with the assistance of CFD modeling to optimize the shape and size of the microstructure. Empirical correlations for the mass transfer coefficient were derived. The pressure drop in micro T-mixers was investigated experimentally and numerically. Correlations describing the friction factor for different flow regimes were developed and predicted values were in good agreement with experimental results. Experimental studies were conducted to develop a highly active and selective catalyst with a proper form for the microreactor. Pd catalysts supported on activated carbon cloths were prepared by different treatments during the catalyst preparation. A variety of characterization methods were used for catalyst investigation. The surface chemistry of the support and the oxidation state of the metallic phase in the catalyst play important roles in catalyst activity and selectivity for the direct synthesis. The direct synthesis of hydrogen peroxide was investigated in a bench-scale continuous process using the novel microreactor developed. The microreactor was fabricated based on the hydrodynamic and mass transfer studies and provided a high interfacial area and high mass transfer coefficient. The catalysts were prepared under optimum treatment conditions. The direct synthesis was conducted at various conditions. The thesis represents a step towards a commercially viable direct synthesis. The focus is on the two main challenges: mitigating the safety problem by utilization of microprocess technology and improving the selectivity by catalyst development.

Value engineering of InnoTrackTM

Middle section module of InnoTrackTM moving walk was re-engineered according to value analysis process. Self-supporting steel structure for moving walk was created as a result of this process. Designed structure was verified and validated by prototype tests and finite element method calculations. Self-supporting steel structure replaces the original design of middle section module in InnoTrackTM. Designed structure provides higher satisfaction to customers’ needs and at the same time, it uses less resources. The redesigned middle section module provides higher value to the customer.

Dynamiikan simulointi poralaitteiden tuotekehityksessä

Diplomityö käsittelee kallioporalaitteen eliniän kuormitusten arviointiin tarkoitetun simulointimallin rakentamista. Työssä luotiin modulaarinen malli, jolla voidaan simuloida dynaamisesti esteen yliajo. Esteen yliajo on perinteinen tehdastesti uusien laitteiden prototyypeille. Sillä pyritään saamaan selville laitteen maksimikuormitustapaukset. Pintaporalaitteen simulointimalli tehtiin ADAMS-ohjelmistolla laitteen suunnittelussa tehtyjä CAD-malleja hyödyntäen. ADAMS-ohjelmistolla mallinnettiin laitteen yksinkertaistettu mekaniikka siten, että laite oli jaettu viiteen eri moduuliin. Runko ja telasto olivat omana osionaan. Puomi ja syöttölaite oli oma kokoonpanonsa ja ohjaamo sekä katteet olivat kaksi erillistä modulia. Viides moduuli oli hydrauliikka, joka simuloitiin rinnakkaissimulointina EASY5-ohjelmistolla. Simuloituja esteen yliajon tuloksia verrattiin prototyyppilaitteen tehdastestien mitattuihin kuormituksiin. Vertailu tehtiin mallinnettujen neljän sylinterin paineita tarkastelemalla. Tuloksia tarkastellessa havaittiin, että simulaatiomalli antaa varsinkin staattisissa tarkasteluissa oikean suuntaisia tuloksia. Dynaamisissa tilanteissa koneen maksimikuormituksilla mallinnustarkkuus ei tämän työn laajuudessa ole riittävä varsinaiseen eliniän analysointiin. Sen sijaan mallinnustekniikka todettiin periaatteessa toimivaksi ja jatkokehityskelpoiseksi.