Análise de desempenho de um fogão solar construído a partir de sucatas de antena de tv

Given the growing environmental crisis caused by degradation, mainly due to the use of polluting energy sources, increasing the growing use of renewable energies worldwide, with emphasis on solar energy, an abundant supply and available to everyone, which can be harnessed in several ways: electricity generation; dehydration of food; heating, disinfection and distillation and cooking. The latter has as its primary feature the viability of clean, renewable energy for society, combating ecological damage caused by large-scale use of firewood for cooking foods, use in tropical countries with high solar radiation, and has funding NGOs throughout the world with the goal of achieving low-income population. The proposed project consists of a solar cooker for concentration, working from the reflection of sunlight by a hub that they converge to a focal point at the bottom of the pot, getting lots of heat. The solar cooker under study consists of two elliptical reflecting parabolas made from the recycling of scrap TV antenna, having 0.29 m² of surface area for each antenna, which were covered by multiple mirrors of 2 mm thick and mounted on a metal structure, with correction for the mobility of the apparent movement of the sun. This structure was built with the recycling of scrap metal, possessing a relatively low cost compared with other solar cookers, around US$ 50.00. This cost becomes negligible, since that will involve a great benefit to not have fuel costs for each meal, unlike the use of gas or firewood for cooking food. The tests show that the cooker has reached the maximum temperature of 740 ° C, for boiling water in an average time of 28 minutes, cooking various types of foods such as potatoes, rice and pasta in an average time of 45 minutes and still going as a solar oven, making pizza baking and meat. These cooking times do not differ much from the cooking times on a gas stove, it becomes the solar cooker as a good consumer acceptance, and furthermore not to deliver the same gases that can poison the food as with the wood stove. Proves the viability of using the stove to cook or bake in two daily meals for a family, still presenting a position to improve his performance with the addition of new materials, equipment and techniques

Palhada do sorgo de guiné gigante no estabelecimento de plantas daninhas em área de plantio direto

A palhada na superfície do solo pode interferir na infestação de plantas daninhas das culturas de verão. O objetivo deste trabalho foi avaliar o efeito da quantidade de palhada do sorgo de guiné gigante sobre a população de plantas daninhas em área de plantio direto. O delineamento experimental foi de blocos ao acaso com quatro repetições. Os tratamentos constaram de 0, 6.100, 7.100, 19.500, 26.700, 28.100 e 30.200 kg ha-1 de palhada do sorgo de guiné sobre os quais foi realizada a semeadura de soja cultivar Monsoy-6101 na densidade de 25 sementes por metro e no espaçamento de 0,45 m entre linhas. Trinta dias após a semeadura, realizou-se o levantamento de plantas daninhas, em quatro amostras por parcela, por meio de moldura metálica de 1 m². Houve redução significativa do número de plantas daninhas estabelecidas com o incremento da palhada. A partir de 15.000 kg ha-1,o controle de plantas daninhas é superior a noventa por cento.

Murcha-de-curtobacterium do feijoeiro no Estado de Santa Catarina e reação de genótipos a Curtobacterium flaccumfaciens pv. flaccumfaciens

Avaliou-se a ocorrência da murcha-de-curtobacterium em lavouras de feijoeiro comum em algumas localidades do Estado de Santa Catarina, nas safras 2002/03 e 2003/04, e o comportamento dos genótipos BRS Valente, Carioca, CHC 97-29, CHP 97-26, CNPF 8104, Diamante Negro, Empasc 201 - Chapecó, IAPAR 44, IPR Graúna, IPR Juriti, IPR Uirapuru, LP 9728, Pérola, SCS 202-Guará, Sel. CP 9310635, TPS Bionobre, TPS Bonito, TPS Magnífico, TPS Nobre, TPS Soberano e Xamego perante Curtobacterium flaccumfaciens pv. flaccumfaciens (Cff), em condições de casa-de-vegetação. As cultivares IAC Carioca Akytã, IAC Carioca Aruã e IAC Carioca Pyatã foram empregadas como padrões de resistência a Cff. As avaliações dos sintomas ocorreram aos 5, 10, 15, 20 e 25 dias após a inoculação (DAI) e, posteriormente, foi estimada a área abaixo da curva de progresso da murcha-de-curtobacterium (AACPMC), em cada genótipo. A doença esteve presente nos municípios de Campos Novos, Faxinal dos Guedes, Guatambu, Ipuaçu, Ponte Serrada e Tigrinhos e que, aos 10 DAI, as cultivares SCS 202 - Guará e IPR Juriti mostraram baixa severidade. Porém, aos 25 DAI, somente as cultivares padrões foram resistentes e apresentaram menor AACPMC.

Viabilidade térmica de um forno solar fabricado com sucatas de pneus

The proposed design provides a solar furnace alternative, box-like, low-cost operation to be used in cooking, comprising three scrap tires to make the recycling thereof. The tires were coupled to each other, forming an enclosure, which stood on its bottom covered by a parable multiple mirrors made from a urupema (sieve indigenous) and the inner sides of the oven aluminum sheet painted black, obtained from beer cans, thus being made to obtain the increase in the concentration of solar radiation incident on the inside of the prototype studied. Two tires were attached, leaving an air layer between them, with the function of thermal insulation. The third tire aimed to support the other two and thermally insulate the bottom of the oven. Externally was placed a metal frame with flat mirrors to reflect the incident rays into the oven, having a mobility to correct the apparent motion of the sun. Its primary feature is the viability of clean, renewable energy to society by tackling the ecological damage caused by the large-scale use of wood for cooking food. The tests show that the furnace reached the maximum temperature of 123.8 °C and baking various foods such as pizza, bun, and other lasagne in an average time 50 minutes. Proves the feasibility of using the oven. Presenting still able to improve their performance with the addition of new materials, equipment and techniques

Estudo da movimentação de plantas aquáticas imersas presentes no reservatório da UHE Eng. Souza Dias - Jupiá

O objetivo deste estudo foi desenvolver um método para determinação de pontos de reprodução e de suas respectivas importâncias na disseminação das espécies E. densa, E. najas e C. demersum no reservatório de Jupiá. Foram monitorados dez locais nos quais se encontrou registro de altas infestações dessas espécies. Dois desses locais situam-se no rio Paraná, nas lagoas denominadas de Ferradura e Pernilongo; os outros oito sítios estão localizados no rio Tietê, nas lagoas marginais Testemunha, Barrenta, Vírgula e Flórida, e no leito do rio nos pontos Acima da Ponte dos Barrageiros, Abaixo da Ponte, Baía ao Lado da Ponte e em frente da Praia de Itapura. em cada um desses sítios de reprodução foram liberados e monitorados dez blocos de plantas aquáticas imersas por mês. Os blocos possuíam volume de 0,14 cm³ e receberam uma etiqueta plástica de identificação externa e uma bóia de cor laranja, com o objetivo de serem facilmente localizadas ou visualizadas à distância. Após a soltura, cada bloco foi georreferenciado por meio de um aparelho GPS, sendo o seu deslocamento avaliado a cada 15 dias. Os sítios Lagoa Vírgula, Lagoa Testemunha e Lagoa Barrenta destacaram-se quanto ao número de blocos (30, 20 e 19 blocos, respectivamente), que percorreram distâncias superiores a 500 m e, conseqüentemente, saíram de seus respectivos locais de reprodução. A grande maioria dos blocos permaneceu dentro da Lagoa Flórida; somente 12 blocos saíram e alcançaram o leito do rio Tietê. O sítio denominado Leito Acima da Ponte foi o que mais se destacou dentre os três localizados no leito do rio Tietê, pois forneceu 18 blocos de plantas, enquanto os sítios Abaixo da Ponte e Baía ao Lado da Ponte forneceram 15 e 14 blocos, respectivamente. O sítio Praia de Itapura foi o que apresentou menor importância em relação ao fornecimento de plantas imersas no rio Tietê, sendo localizadas apenas 11 bóias com deslocamento superior a 500 m. Os sítios de reprodução localizados no rio Paraná também contribuíram para o fornecimento de plantas imersas ao reservatório de Jupiá; nove blocos saíram da Lagoa Pernilongo e apresentaram deslocamentos superiores a 500 m. Entretanto, os sítios Lagoa Barrenta e Lagoa Ferradura foram aqueles que mais contribuíram com a chegada de plantas na tomada de água da UHE Eng. Souza Dias, uma vez que foram recolhidos, respectivamente, seis e quatro blocos de plantas provenientes desses locais de dispersão. A metodologia utilizada mostrou-se eficaz quanto à avaliação da movimentação de plantas aquáticas imersas dentro do reservatório de Jupiá.

Avaliação da eficiência de catalisadores comerciais na obtenção de biodiesel de algodão (Gossipium hisutum L.)

The increasing demand for energy and the environment consequences derived from the use of fossil energy, beyond the future scarcity of the oil that currently is the main power plant of the world, it stimulated the research around the production of biodiesel. In this work the synthesis of biodiesel of cotton in the methyl route was carried through, for had been in such a way used catalyst commercial homogeneous, Na-Methylat and the K-Methylat, aiming to the evaluation of the efficiency of them. An experimental planning 23 was elaborated aiming to evaluate the influence of the variable (molar reason oil/alcohol, % of catalyst and temperature) in the process as well as indicating the excellent point of operation in each case. The biodiesel was analyzed by gaseous chromatography, indicating a conversion of 96,79% when used Na-Methylat® as catalytic, and 95,65% when the K-Methylat® was used. Optimum result found with regard to the conversion was obtained at the following conditions: molar reason oil/alcohol (1:8), temperature of 40°C and 1% of catalyst Na-Methylat, reaching a 96,79% conversion, being, therefore, above of the established for the European norm (96.5%). The analysis of regression showed that the only significant effect for a confidence level of 95%, was of the changeable temperature. The variance analysis evidenced that the considered model is fitted quite to the experimental response, being statistically significant; however it does not serve inside for make forecasts of the intervals established for each variable. The best samples were analyzed by infra-red (IR) that identified the strong bands of axial deformation C=O of methylic ester, characterized through analyses physicochemical that had indicated conformity with the norms of the ANP, that with the thermal and rheological analyses had together evidenced that biodiesel can be used as combustible alternative in substitution to diesel

Síntese e caracterização de tungstatos de cério e estrôncio para fins catalíticos

The main goal of this work was to produce nanosized ceramic materials of the family of the tungstates (tungstates of cerium and strontium), and test them for their catalytic activity in processes involving the transformation of methane (CH4). The methodology used for the synthesis of the ceramic powders involved the complexation combining EDTA-citrate. The materials characterization was performed using simple and differential thermogravimetry, x-ray diffraction, transmission electron microscopy, and energy dispersive spectroscopy (EDS). The microstructure analysis was performed using the refinement by the Rietveld method, and the crystallite size and distribution of the materials was elucidate by the Scherrer and Williamson-Hall methods. The conditions of the synthesis process for the three envisaged materials (SrWO4, SrWO4 using tungsten oxide concentrate as raw material, and Ce2(WO4)3) were adjusted to obtain a single phase crystalline material. The catalytic tests were carried out in the presence of methane and synthetic air, which is composed of 21% O2 and 79% N2. The analysis of the conversion of the reaction was done with the aid of an fourier transform infrared device (FTIR). The analysis showed that, structurally, the SrWO4 produced using raw materials of high and poor purity (99% and 92%, respectively) are similar. The ideal parameters of calcination, in the tested range, are temperature of 1000 °C and time of calcination 5 hours. For the Ce2(WO4)3, the ideal calcination time and are temperature 15 hours and 1000°C, respectively. The Williamson-Hall method provided two different distributions for the crystallite size of each material, whose values ranged between the nanometer and micrometer scales. According to method of Scherrer, all materials produced were composed of nanometric crystallites. The analyses of transmission electron microscopy confirmed the results obtained from the Williamson- Hall method for the crystallite size. The EDS showed an atomic composition for the metals in the SrWO4 that was different of the theoretical composition. With respect to the catalytic tests, all materials were found to be catalytically active, but the reaction process should be further studied and optimized.

Avaliação cinética e potencial do Nb2O5 obtido a partir de um complexo de nióbio para formação do oleato de metila através da reação de esterificação do ácido oleico

Among the heterogeneous catalysts materials made from niobium show up as an alternative to meet the demand of catalysts for biodiesel production. This study aims to evaluate the potential of a heterogeneous catalyst derived from a complex of niobium in the reaction of methyl esterification of oleic acid. The catalyst was synthesized after calcination at different temperatures of a niobium complex ((NH4)3[NbO(C2O4)3].H2O) generating a niobium oxide nanostructure with a different commercial niobium oxide used to synthesize the complex. The commercial niobium oxide, the complex niobium and niobium catalyst were characterized by thermogravimetry (TG and DTA), surface area analysis (BET), scanning electron microscopy (SEM) and X-ray diffraction (XRD), showing the catalyst has researched morphological and crystallographic indicating a catalytic potential higher than that of commercial niobium oxide characteristics. Factorial with central composite design point, with three factors (calcination temperature, molar ratio of alcohol/oleic acid and mass percentage of catalyst) was performed. Noting that the optimal experimental point was given by the complex calcination temperature of 600°C, a molar ratio alcohol/oleic acid of 3.007/1 and the catalyst mass percentage of 7.998%, with a conversion of 22.44% oleic acid in methyl oleate to 60 min of reaction. We performed a composite linear and quadratic regression to determine an optimal statistical point of the reaction, the temperature of calcination of the complex at 450°C, the molar ratio of alcohol/oleic acid 3.3408/1 and mass percentage of catalyst of 7.6833% . Kinetic modeling to estimate parameters for heterogeneous catalysis it set well the experimental results with a final conversion of 85.01% with 42.38% of catalyst and without catalyst at 240 min reaction was performed. Allowing to evaluate the catalyst catalytic studied has the potential to be used in biodiesel production

Equilíbrio líquido-líquido para o sistema biodiesel de óleo de semente de melão (Cucumis melo l.) + metanol + glicerina

Rio Grande do Norte, northeast state from Brazil, it is the greatest producer and exporter of yellow melon, well known as Spanish melon. Despite the consumption of this fruit to be mainly its pulp, melon seeds are an important source of lipids considered an industrial residue it has been discharge product. The use of oilseeds in order to produce biodiesel establishes an important raw material and the increase of its production promotes the national development of the agriculture. In this background, the aim of this work has been to use oil from seeds of yellow melon to produce biodiesel and to accomplish a study of the phase equilibrium of the system evolving biodiesel, methanol and glycerin. The biodiesel was obtained by oil transesterification through methylic route with molar ratio 1:9.7 (oil:alcohol) and with a mass of NaOH of 0.5% from the oil mass; the reaction time was 73 minutes at 55 °C. A yield of 84.94% in biodiesel was achieved. The equilibria data present a well-characterized behavior with a great region of two phases. The tie lines indicate that methanol has a best solubility in the phase that is rich in glycerin. Consistency of the experimental data was made based on Othmer-Tobias and Hand correlations which values above 0.99 were found to correlation coefficients, this fact confers a good thermodynamic consistency to the experimental data. NRTL and UNIQUAC models were employed to predict liquid-liquid equilibrium of this system. It was observed a better concordance of the results when NRTL was applied (standard deviation 1.25%) although the UNIQUAC model has presented a quite satisfactory result either (standard deviation 2.70%). The NRTL and UNIQUAC models were also used to evaluate the effect of temperature in the range of 328 K to 358 K, in which a little change in solubility with respect to the data obtained at 298 K was observed, thus being considered negligible the effect of temperature

Produção de bioetanol a partir de pedúnculo de caju (Anacardium occidentale L.) por fermentação submersa

Recently, global demand for ethanol fuel has expanded very rapidly, and this should further increase in the near future, almost all ethanol fuel is produced by fermentation of sucrose or glucose in Brazil and produced by corn in the USA, but these raw materials will not be enough to satisfy international demand. The aim of this work was studied the ethanol production from cashew apple juice. A commercial strain of Saccharomyces cerevisiae was used for the production of ethanol by fermentation of cashew apple juice. Growth kinetics and ethanol productivity were calculated for batch fermentation with different initial sugar (glucose + fructose) concentration (from 24.4 to 103.1 g.L-1). Maximal ethanol, cell and glycerol concentrations (44.4 g.L-1, 17.17 g.L-1, 6.4 g.L-1, respectively) were obtained when 103.1 g.L-1 of initial sugar concentration were used, respectively. Ethanol yield (YP/S) was calculated as 0.49 g (g glucose + fructose)-1. Pretreatment of cashew apple bagasse (CAB) with dilute sulfuric acid was investigated and evaluated some factors such as sulfuric acid concentration, solid concentration and time of pretreatment at 121°C. The maximum glucose yield (162.9 mg/gCAB) was obtained by the hydrolysis with H2SO4 0.6 mol.L-1 at 121°C for 15 min. Hydrolysate, containing 16 ± 2.0 g.L-1 of glucose, was used as fermentation medium for ethanol production by S. cerevisiae and obtained a ethanol concentration of 10.0 g.L-1 after 4 with a yield and productivity of 0.48 g (g glucose)-1 and 1.43 g.L-1.h-1, respectively. The enzymatic hydrolysis of cashew apple bagasse treated with diluted acid (CAB-H) and alkali (CAB-OH) was studied and to evaluate its fermentation to ethanol using S. cerevisiae. Glucose conversion of 82 ± 2 mg per g CAB-H and 730 ± 20 mg per g CAB-OH was obtained when was used 2% (w/v) of solid and loading enzymatic of 30 FPU/g bagasse at 45 °C. Ethanol concentration and productivity was achieved of 20.0 ± 0.2 g.L-1 and 3.33 g.L-1.h-1, respectively when using CAB-OH hydrolyzate (initial glucose concentration of 52.4 g.L-1). For CAB-H hydrolyzate (initial glucose concentration of 17.4 g.L-1), ethanol concentration and productivity was 8.2 ± 0.1 g.L-1 and 2.7 g.L-1.h-1, respectively. Hydrolyzates fermentation resulted in an ethanol yield of 0.38 g/g glucose and 0.47 g/g glucose, with pretreated CABOH and CAB-H, respectively. The potential of cashew apple bagasse as a source of sugars for ethanol production by Kluyveromyces marxianus CE025 was evaluated too in this work. First, the yeast CE025 was preliminary cultivated in a synthetic medium containing glucose and xylose. Results showed that it was able to produce ethanol and xylitol at pH 4.5. Next, cashew apple bagasse hydrolysate (CABH) was prepared by a diluted sulfuric acid pre-treatment. The fermentation of CABH was conducted at pH 4.5 in a batch-reactor, and only ethanol was produced by K. marxianus CE025. The influence of the temperature in the kinetic parameters was evaluated and best results of ethanol production (12.36 ± 0.06 g.L-1) was achieved at 30 ºC, which is also the optimum temperature for the formation of biomass and the ethanol with a volumetric production rate of 0.25 ± 0.01 g.L-1.h-1 and an ethanol yield of 0.42 ± 0.01 g/g glucose. The results of this study point out the potential of the cashew apple bagasse hydrolysate as a new source of sugars to produce ethanol by S. cerevisiae and K. marxianus CE025. With these results, conclude that the use of cashew apple juice and cashew apple bagasse as substrate for ethanol production will bring economic benefits to the process, because it is a low cost substrate and also solve a disposal problem, adding value to the chain and cashew nut production

Recuperação e purificação de ramnolipídeos produzidos por pseudomonas aeruginosa P029-GVIIA utilizando melaço de cana como substrato

Biosurfactants are molecules produced by microorganisms mainly bacteria as Pseudomonas and Bacillus. Among the biosurfactants, rhamnolipids play an important role due to their tensoactive as well as emulsifying properties. Besides can be produced in a well consolidated way the production costs of biosurfactants are quite expansive mainly if downstream processing is goning to be considered. Actually, attention has been given to identification of biosurfactants as well as optimization of its fermentative processes including downstream ones. This work deals with the development of strategies to recovery and purification of rhamnolipids produced by Pseudomonas aeruginosa P029-GVIIA using sugar-cane molasses as substrate. Broth free of cells was used in order to investigate the best strategies to recovery and purification produced by this system. Between the studied acids (HCl and H2SO4) for the acid precipitation step, HCl was the best one as has been showed by the experimental design 24. Extraction has been carried out using petroleum ether and quantification has been done using the thioglycolic acid method. Adsorption studies were carried out with activated carbon in a batch mode using a 24 experimental design as well as combined with an hydrophobic resin Streamline Phenyl aiming to separate the produced biosurfactant. Biosurfactant partial identification was carried out using High Performance Liquid Chromatography (HPLC). Experiments in batch mode showed that adsorption has been controlled mainly by pH and temperature. It was observed a reduction of 41.4% for the liquid phase and the solid phase it was possible to adsorb up to 15 mg of rhamnolipd/g of activated carbon. The kinetics of adsorption has been well fitted to a pseudo-first order reaction with velocity constant (k1) of 1.93 x 10-2 min-1. Experiments in packed bed ranging concentration on eluent (acetone) has been shown the highest recovery factor of 98% when pure acetone has been used. The combined effect if using activated carbon with an hydrophobic resin Streamline Phenyl has been shown successful for the rhamnolipids purification. It has been possible to purify a fraction of the crude broth with 98% of purity when the eluted of activated carbon packed bed was used with pure acetone

Influência das condições de cultivo na produção de antígenos recombinantes de Leishmania i. chagasi utilizando Escherichia coli M15 cultivada em incubador rotativo e biorreator

Escherichia coli has been one of the most widely used hosts in recombinant protein production, in both laboratory and industrial scale since the advent of recombinant DNA technology. Despite the substantial progress of studies on the molecular biology and immunology of infections, there is currently no medication-based prophylaxis capable of preventing leishmaniasis. As such, there is a great need to identify specific antigens for the development of vaccines and diagnostic kits against visceral leishmaniasis. Thus, the primary goal of the present study is to assess the influence of cultivation conditions on the production of Leishmania chagasi antigens, carried out in a rotating incubator and bioreactor. To that end, several assays were conducted to evaluate the kinetic behavior of antigens (648, 503) of Leishmania. i. chagasi in two different compositions of media (2xTY, TB), with and without an inducer. In order to improve expression, assays were performed in a benchtop bioreactor using the best conditions obtained in a rotating incubator, in addition to assessing the influence of stirring speed. Results show that high complexity of the cultivation medium favored kinetic growth of clones (648, 503). However, in assays submitted to induction by IPTG, this elevated complexity did not promote the expression of recombinant proteins. Expression of antigens 648 and 503 exhibited behavior associated with growth and, in terms of location, proteins 648 and 503 are intracellularly stored. Lactose may be the most adequate inducer in protein expression, when considering factors, cost, toxicity and stability. Elevated stirring may increase cell growth in clone 53, although it may not result in high concentrations for the protein of interest. On the other hand, positive results were obtained for all recombinant clones (648, 503) tested, confirmed by the electrophoretic profile

Construção e aplicação de uma sequência didática para o ensino de trigonometria usando software geogebra

The present study aims to analyze the potentialities and limitations of GeoGebra software on what concerns trigonometry s teaching and learning processes. Taking the present resources of public school from the state of Rio Grande do Norte, the research intends to answer the following question: Could we use the current conditions of public school and the Geogebra software to optimize the trigonometry s learning and teaching processes situation? . To make it a possible to answer the question above, a module of investigative activities was created and applied. The methodological intervention was made among second year High School students from a public school in Natal, RN. The theoretical reference of Mathematics Didactics was taken was a base, adopting the conceptions of Borba and Penteado (2001), Valente (1999) and Zulatto (2002, 2007) about the use of Information Technology (IT) on Mathematics classrooms. In order to create the investigative activities helped us to understand how the students make their constructions and their visual perception through the process of dragging images on the computer screen. Furthermore, the activities done with the GeoGebra software s resources facilitate the resolution of trigonometry situations

Matemática Védica no ensino das quatro operações

This paper describes a study on the possibilities of teaching Vedic Mathematics for teaching the four operations. For this various literature sources were consulted considering three main aspects. The first of a historical-cultural, in order to gather information about the Mathematics originated from Vedic civilization, which highlight (Plofker, 2009), (Joseph, 1996), (Bishop, 1999), (Katz, 1998), (Almeida , 2009). This sought to emphasize relationships of the development of this culture with the math involved in the book Vedic Mathematics written by Tirthaji and published in 1965. In this respect the work brings notes on the history of mathematics on the development of mathematics in ancient India. The second aspect was related to teaching mathematics through research activities in the classroom, in this sense, I sought a bibliography to assist in the construction of a proposed activity to teach the four operations, based on the sutras of Vedic Mathematics, but within an investigative approach, assisting in the development of mental calculation strongly stimulated by the Vedic Mathematics Sutras. The authors were adopted (Mendes, 2006, 2009a, 2009b), Bridge (2003). The third aspect considered to search for books on teaching Vedic Mathematics, written by other authors, based on the book by Tirthaji. This revealed Vedic Mathematics textbooks adopted in schools and free courses in the UK, USA and India, all based on the book Vedic Mathematics of Tirthaji. From the bibliographical studies were prepared didactic guidelines and suggested activities for the teacher, to assist in teaching the four operations. The educational product, consisting of Chapters 4 and 5, is the body of the dissertation and consists of didactic guidelines and suggestions for activities that aim to contribute to the teachers who teach initial years of elementary school

A relação gramatical objeto direto : implicações para o ensino de língua materna

This paper attempts to investigate the discourse manifestations of the grammatical relation direct object with respect to the syntactic, semantic and pragmatic properties that underlie this element. The research adopts theoretical orientation of the functionalism from North American and Brazilian schools inspired in Givón (1995, 2001), Hopper and Thompson (1980), Chafe (1979), Furtado da Cunha, Oliveira, Martelotta (2003) inter alia. From functionalism, the research uses principles of iconicity, markedness and informativity and it analize categories of transitivity, grounding and animacy. This research is anchored in prototype model (TAYLOR 1995); construction grammar model (GOLDBERG 1996, 2002). Both theoretical orientations share the view that language is a malleable living organism subject to socio-cultural context. Grammar is then the result of created, maintained, and systematized linguistic patterns developed from and used for language use. According to a functional linguistics and cognitivist linguistics verbs are stored in the speakers lexicon in syntactic-semantic frames which are more frequent. These frames carry information concerning obligatory and optional arguments and the semantic roles these arguments take in the clause. The analysis focuses on the semantic type of the verbs and its relationship with the argument encoded as a direct object observing the aspectual nature of verbs. Direct objects are classified according to their morphology (lexical or pronominal noun phrase), semantic role, informational content and animacy. This study discusses pedagogical implications with relation to how the grammatical concepts touched on this paper are treated in school textbooks. The empirical data come from Corpus Discurso & Gramática: a língua falada e escrita na cidade do Natal (FURTADO DA CUNHA, 1998). This corpus is composed of texts that contain spoken and written modalities. These modalities are in turn organized according to different types: personal narratives, retold narrative, description of preferred place, procedural place, procedural description and report on argumentation. The sample data totals 40 texts produced by four language consultants of the last graduation date. The paper shows that the same syntactic structures (formed through Subject-Verb-Object) correspond to different semantic-pragmatic structures in relation to specific communicative purposes even verb is an event, process or state. The argument structure are not aleatory but are related to experience; that is the way humans conceptualize the world and talk about it