A Comparati ve Study of Mechanical and Tribological Properties of AISI-304 and AISI-316 Submitted to Glow Discharge Nitriding

Mechanical and tribological properties of AISI 304 and AISI 316 stainless steels submitted to glow discharge ion nitriding are reported. The atmosphere was 20:80 - N2:H2 with substrate temperatures ranging from 300 to 500 °C. Treatment at 300 °C produced expanded austenite (γN) in both steels. Increasing the temperature, the phases γ′-Fe4N and ε- Fe2+xN were present and the latter is the major phase for AISI 304. At 500 °C, the CrN phase was also identified in both steels. Hardnesses of about 13-14 GPa at near surface regions were obtained in both steels. Moreover, AISI 316 nitrided at 500 °C has the deepest hard layer. Tribological tests showed that wear can be reduced by up to a factor of six after the nitriding processes, even for a working temperature of 300 °C. The profiles during and after nanoscratch tests did not reveal significant differences after nitriding processes in both steels.

A Comparative Study of Mechanical and Tribological Properties of AISI-304 and AISI-316 Submitted to Glow Discharge Nitriding

Mechanical and tribological properties of AISI 304 and AISI 316 stainless steels submitted to glow discharge ion nitriding are reported. The atmosphere was 20:80 - N2:H2 with substrate temperatures ranging from 300 to 500 °C. Treatment at 300 °C produced expanded austenite (γN) in both steels. Increasing the temperature, the phases γ′-Fe4N and ε- Fe2+xN were present and the latter is the major phase for AISI 304. At 500 °C, the CrN phase was also identified in both steels. Hardnesses of about 13-14 GPa at near surface regions were obtained in both steels. Moreover, AISI 316 nitrided at 500 °C has the deepest hard layer. Tribological tests showed that wear can be reduced by up to a factor of six after the nitriding processes, even for a working temperature of 300 °C. The profiles during and after nanoscratch tests did not reveal significant differences after nitriding processes in both steels.

Desmame em recém-nascidos de muito baixo peso ao nascer no primeiro retorno ambulatorial após a alta hospitalar

Investigate intrahospital and neonatal determinants associated to the weaning of very low birth weight (VLBW) infants. Methods: 119 VLBW (<1500g) infants 81 were monitored from July 2005 through August 2006, from birth to the first ambulatory visit after maternity discharge. This maternity unit uses the Kangaroo Method and the Baby Friendly Hospital Initiative. Results: Out of 119 VLBW infants monitored until discharge, 88 (75%) returned to the facility, 22 (25%) were on exclusive breastfeeding (EB) and 66 (75%) were weaned (partial breastfeeding or formula feeding). Univariate analysis found an association between weaning and lower birth weight, longer stays in the NICU and longer hospitalization times, in addition to more prolonged enteral feeding and birth weight recovery period. Logistic regression showed length of NICU stay as being the main determinant of weaning. Conclusion: The negative repercussion on EB of an extended stay in the NICU is a significant challenge for health professionals to provide more adequate nutrition to VLBW infants

Estimation of genetic parameters for partial egg production periods by means of random regression models

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Partial protection against tissue cysts formation in pigs vaccinated with crude rhoptry proteins of Toxoplasma gondii

A vaccine containing crude Toxoplasma gondii rhoptry proteins incorporated in the immunostimulating complexes (ISCOM) adjuvant was tested in pigs for protecting against tissue cyst formation. For this, 38 mixed breed pigs were divided into four groups, G1 (vaccinated challenged, n = 10) received two doses (100 mu g/dose) of the rhoptry vaccine at days 0 and 21, G2 (vaccinated challenged, n = 10) received viable tachyzoites (7 x 10(7)) of the RH strain at day 0, G3 (unvaccinated challenged, n = 10) and G4 (unvaccinated unchallenged, n = 8). Pigs were challenged with 4 x 10(4) VEG strain oocysts 57 days later. The G1 pigs produced high IgG antibody levels in the indirect enzyme-linked immunosorbent assay (ELISA) after the second dose of rhoptry vaccine, but were not clinically protected against a high dose oocyst challenge. Partial protection was observed in G1 at the chronic phase of infection, when compared with G3. Pigs in group 2 developed high antibody levels and were protected against clinic signs. T gondii was not detected in two (G1) and three (G2) pigs by mouse bioassay. The results indicate partial protection in pigs vaccinated with a rhoptry vaccine. (c) 2005 Elsevier B.V. All rights reserved.

Poultry feed metabolizable energy determination using total or partial excreta collection methods

The aim of this work was to compare the efficiency of total (TC) or partial (PC) collection excreta methods to determine metabolizable energy in poultry feeds. A number of 180 12- to 21-day-old broilers were distributed into two treatments of six replicates of 10 birds each. A reference-diet was formulated to supply broiler requirements, and the test-diets consisted of 60% of reference diets and 40% of corn or soybean meal. Celite was added at 1% to the diets as a marker. Excreta and diet samples were analyzed for dry matter, energy, nitrogen, and acid-insoluble ash (AIA). AME of corn determined by partial collection (PC) was higher (3544 kcal/kg) as compared to total collection (TC) (3133 kcal/kg). However, no difference were observed for soybean meal (1797 vs. 1821 kcal/kg) between both methods. Marker recovery rates in the excreta were 101, 111, and 96% for the basal-diet, and the test-diets with corn or soybean meal, respectively. This result indicates the importance of marker recovery rate in the excreta to evaluate feed AME and digestibility.

Changes on emitter discharge under different water temperature and pressure

The study was conducted at the Research Laboratory of Hydraulic and Irrigation Group in the Rural Engineering Department, Technical University of Madrid (Universidad Politecnica de Madrid), Madrid, Spain. Water temperatures of 20, 30, 40 degrees C and system pressures often encountered in irrigation practices of 80, 90, 100, 110, 120, 130, 140, 150, 160, 170, 180, 190 and 200 k Pa were applied to determine the effects of different water temperatures and pressures on emitter discharge. Non-pressure compensating in-line emitter which has turbulent flow regime with a long-path (labyrinth), emitter discharge was 4 L h(-1) at system pressure of 100 kPa according to the manufacturer recommended, was used. Emitters were spaced 20 cm along the drip laterals with 16 mm diameter. Discharge equations and coefficients of variation related to temperatures of 20, 30 and 40 degrees C were obtained as q = 0.375H(0.51), q = 0.358H(0.52), q = 0.346H(0.53) and 2.68, 2.09, 3.65, respectively. Discharge of the emitter was affected by different system pressures and increased as potentially (R = 0993-0996). In general. the emitter discharge increased with increasing temperature. However, especially in the common system pressures of 90-120 k Pa, differences of obtained emitter discharges between the different water temperatures were not significant (1%).

Avaliação do comportamento tribológico de compósitos poliéster/fibra de vidro utilizando resíduos de poliéster/fibra de vidro e carbonato de cálcio como carga

The use of composite materials and alternative is being increased every day, as it becomes more widespread awareness that the use of renewable and not harmful to the environment is part of a new environmentally friendly model. Since its waste (primarily fiberglass) can not be easily recycled by the difficulty that still exists in this process, since they have two phases mixed, a polymeric matrix thermoset difficult to recycle because it is infusible and phase of fiber reinforcements. Thermoset matrix composites like Polyester + fiberglass pose a threat due to excessive discharge. Aiming to minimize this problem, aimed to reuse the composite Polyester + fiber glass, through the wastes obtained by the grinding of knifes and balls. These residues were incorporated into the new composite Polyester/Fiberglass for hot compression mold and compared tribological to composites with filler CaCO3, generally used as filler, targeting a partial replacement of CaCO3 by such waste. The composites were characterized by thermal analysis (TGA, DSC and DMA), by the surface integrity (roughness determination, contact angle and surface energy), mechanical properties (hardness) and tribological tests (wear and coefficient of dynamic friction) in order to evaluate the effect of loads and characterize these materials for applications that can take, in the tribological point of view since waste Polyester + fiberglass has great potential for replacement of CaCO3

Diagnóstico de descarga de cátodo oco de ar e pós-descarga Ar N2 por espectroscopia de emissão óptica e espectrometria de massa

Many applications require that the plasma discharge is produced apart from the surface to be processed, thus preventing damage caused by bombardment and/or plasma radiation. In the post-discharge regime in various applications thermally sensitive materials can be used. In this work, active species produced by discharge and post-discharge hollow cathode were diagnosed by optical emission spectroscopy and mass spectrometry. The discharge was produced with the gases Ar and Ar - N2 gas flow ranging from 1 to 6 cm3/min and electric current between 150 to 600 mA. It was estimated that the ion density inside the hollow cathode, with 2 mm diameter ranged between 7.71 and 14.1 x 1015 cm-3. It was observed that the gas flow and the electric current changes the emission intensity of Ar and N2 species. The major ionic species detected by quadrupole mass spectrometry were Ar+ and N2+. The ratio of optical emission intensities of N2(1 +)/Ar(811 nm) was related to the partial pressure of N2 after the hollow cathode discharge at low pressure

Comparison of Botryosphaeran production by the ascomyceteous fungus Botryosphaeria sp., grown on different carbohydrate carbon sources, and their partial structural features

The influence of glucose concentration and other carbohydrates (monosaccharides: fructose, galactose, mannose; polyols: mannitol and sorbitol; disaccharides: lactose, sucrose and commercial sucrose; and industrial sugarcane molasses) were compared as sole carbon sources for the production of Botryosphaeran, an exopolysaccharide (EPS) produced by Botryosphaeria sp. The optimum glucose concentration for EPS production was 50 g 1(-1). With the exception of mannitol, the fungus produced EPS on all carbon sources studied, with highest yields occurring with sucrose followed by glucose. All EPS showed exclusively glucose after acid hydrolysis and monosaccharide analysis. FTIR spectroscopy demonstrated the presence of beta-anomers indicating that all the EPS produced by Botryosphaeria sp. on the different carbon sources were essentially of the beta-D-glucan type.

Partial characterization of proteins from baru (Dipteryx alata Vog) seeds

BACKGROUND: Baru (Dipteryx alata Vog.) is a fruit distributed throughout the Brazilian savanna and contains a seed with a high protein content, whose properties have been rarely explored. The purpose of this study was to characterize this protein, especially by isolation and quantifying its fractions and measuring some of its molecular properties.RESULTS: Baru seeds contain 244 g kg(-1) protein on a dry weight basis. Solubility profiles showed a preponderance of globulins. This fraction dominated the seed composition, with 61.7 wt% of the total soluble proteins. Albumins and glutelins accounted for 14 and 3.3 wt%, respectively. SDS-PAGE resolution of albumin and globulin showed main bands with molecular weights of 84 kDa and 64,66 and 73 kDa, respectively. The total protein of the flour and the globulin showed values of in vitro digestibility of 85.59% and 90.54%, relative to casein. Total globulin produced only one chromatographic peak, both on Sepharose CL-6B gel filtration and on DEAE-cellulose ion-exchange columns, eluted at a concentration of 0.12 mol L(-1) NaCl.CONCLUSION: The baru seed had high protein content with large quantities of storage proteins. The chromatographic and solubility profiles indicate the predominance of a fraction with characteristics of a legumin-type protein. (C) 2011 Society of Chemical Industry

Isolation and partial characterization of a 30 kDa adhesin from Paracoccidioides brasiliensis

The virulence of Paracoccidioides brasiliensis can be attenuated or lost after long periods of repeated subculturing and reestablished after animal inoculation. Only one adhesin (gp43) has been described until now, among the various identified components of P. brasiliensis, and gp43 shows adhesion to laminin. Thus, the present study was designed to isolate and characterize factors putatively related to the capacity of this fungus to adhere to the host by comparing P brasiliensis samples, taken before and after animal inoculation. The two samples differed in their pattern of adhesion and invasion. The sample recently isolated from animals (Pb18b) demonstrated a greater capacity to adhere and to invade the Vero cells than the one subcultured in vitro (Pb18a). Extract from Ph18b also showed higher levels of protein expression than that from Pb18a, when two-dimensional electrophoresis gels were compared. A protein species of 30 kDa, pI 4.9, was more evident in the Pb18b extract and had properties of adhesin. Laminin, but none of the other extracellular matrix (ECM) components, such as fibronectin, collagen I and IV, bound specifically to the P. brasiliensis 30 kDa protein. The roles of 30 kDa and gp43 in cellular interactions were investigated and the adhesion of P. brasiliensis yeast cells was intensively inhibited by pre-treatment of epithelial cells with 30 kDa protein and gp43. Thus, this study presents evidence that adhesion capacity could be related to virulence, and that a 30 kDa adhesin accumulated differentially in samples with different levels of pathogenicity. This protein and its adhesion characteristics are being published for the first time and may be related to the virulence of P brasiliensis. (c) 2005 Elsevier SAS. All rights reserved.

Treatment of PET and PU polymers by atmospheric pressure plasma generated in dielectric barrier discharge in air

Plasma treatments are frequently employed to modify surface properties of materials such as adhesivity, hydrophobicity, oleophobicity etc. Present work deals with surface modification of common commercial polymers such as polyethylene terephthalate (PET) and polyurethane (PU) by an air dielectric barrier discharge (DBD) at atmospheric pressure. The DBD treatment was performed in a plain reactor in wire-duct geometry (non-uniform field reactor), which was driven by a 60 Hz power supply. Material characterization was carried out by water contact angle measurements, atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The plasma-induced modifications are associated with incorporation of polar oxygen and nitrogen containing groups on the polymer surface. The AFM analysis reveals that the plasma treatment roughens the material surface. Due to these structural and morphological changes the surface of DBD-treated polymers becomes more hydrophilic resulting in enhanced adhesion properties. (C) 2010 Elsevier B.V. All rights reserved.

Surface modification of siloxane containing polyurethane polymer by dielectric barrier discharge at atmospheric pressure

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Modification of polyethylene terephthalate by atmospheric pressure dielectric barrier discharge (DBD) in view of improving the polymer wetting properties

Surface treatment of polymers by discharge plasmas has increasingly found industrial applications due to its capability of modifying uniformly the surface without changing the material bulk properties. This work deals with surface modification of polyethylene terephthalate (PET) by a dielectric barrier discharge (DBD) at atmospheric pressure. The treatments were conducted in air, nitrogen or argon plasma. The polymer surface was characterized by contact angle measurement, X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). The results show that the plasma treatment introduces oxygen-and nitrogen-related polar groups on the polymer surface and promotes the surface roughening. Both plasma-induced surface modifications contribute to the enhancement of the polymer wettability.