PRODUCTION OF BIOFUEL INTERMEDIATES FROM WOODY FEEDSTOCKS VIA FAST PYROLYSIS AND TORREFACTION

The main objective of this research was to investigate pyrolysis and torrefaction of forest biomass species using a micropyrolysis instrument. It was found that 30-45% of the original sample mass remained as bio-char in the pyrolysis temperature range of 500 - 700˚C for aspen, balsam, and switchgrass. The non-char mass was converted to gaseous and vapor products, of which 10-55% was water and syngas, 2-12% to acetic acid, 2-12% to hydroxypropanone, 1-3% to furaldehyde, and 5-15% to various phenolic compounds. In addition, several general trends in the evolution of gaseous species were indentified when woody feedstocks were pyrolyzed. With increasing temperature it was observed that: (1) the volume of gas produced increased, (2) the volume of CO2 decreased and the volumes of CO and CH4 increased, and (3) the rates of gas evolution increased. In the range of torrefaction temperature (200 - 300˚C), two mechanistic models were developed to predict the rates of CO2 and acetic acid product formation. The models fit the general trend of the experimental data well, but suggestions for future improvement were also noted. Finally, it was observed that using torrefaction as a pre-curser to pyrolysis improves the quality of bio-oil over traditional pyrolysis by reducing the acidity through removal of acetic acid, reducing the O/C ratio by removal of some oxygenated species, and removing a portion of the water.

Design Optimization of Modern Machine-drive Systems for Maximum Fault Tolerant and Optimal Operation

Modern electric machine drives, particularly three phase permanent magnet machine drive systems represent an indispensable part of high power density products. Such products include; hybrid electric vehicles, large propulsion systems, and automation products. Reliability and cost of these products are directly related to the reliability and cost of these systems. The compatibility of the electric machine and its drive system for optimal cost and operation has been a large challenge in industrial applications. The main objective of this dissertation is to find a design and control scheme for the best compromise between the reliability and optimality of the electric machine-drive system. The effort presented here is motivated by the need to find new techniques to connect the design and control of electric machines and drive systems. A highly accurate and computationally efficient modeling process was developed to monitor the magnetic, thermal, and electrical aspects of the electric machine in its operational environments. The modeling process was also utilized in the design process in form finite element based optimization process. It was also used in hardware in the loop finite element based optimization process. The modeling process was later employed in the design of a very accurate and highly efficient physics-based customized observers that are required for the fault diagnosis as well the sensorless rotor position estimation. Two test setups with different ratings and topologies were numerically and experimentally tested to verify the effectiveness of the proposed techniques. The modeling process was also employed in the real-time demagnetization control of the machine. Various real-time scenarios were successfully verified. It was shown that this process gives the potential to optimally redefine the assumptions in sizing the permanent magnets of the machine and DC bus voltage of the drive for the worst operating conditions. The mathematical development and stability criteria of the physics-based modeling of the machine, design optimization, and the physics-based fault diagnosis and the physics-based sensorless technique are described in detail. To investigate the performance of the developed design test-bed, software and hardware setups were constructed first. Several topologies of the permanent magnet machine were optimized inside the optimization test-bed. To investigate the performance of the developed sensorless control, a test-bed including a 0.25 (kW) surface mounted permanent magnet synchronous machine example was created. The verification of the proposed technique in a range from medium to very low speed, effectively show the intelligent design capability of the proposed system. Additionally, to investigate the performance of the developed fault diagnosis system, a test-bed including a 0.8 (kW) surface mounted permanent magnet synchronous machine example with trapezoidal back electromotive force was created. The results verify the use of the proposed technique under dynamic eccentricity, DC bus voltage variations, and harmonic loading condition make the system an ideal case for propulsion systems.

Emergence and fate of siloxanes in waste streams: Release mechanisms, partitioning and persistence in three environmental compartments

Siloxanes are widely used in personal care and industrial products due to their low surface tension, thermal stability, antimicrobial and hydrophobic properties, among other characteristics. Volatile methyl siloxanes (VMS) have been detected both in landfill gas and biogas from anaerobic digesters at wastewater treatment plants. As a result, they are released to gas phase during waste decomposition and wastewater treatment. During transformation processes of digester or landfill gas to energy, siloxanes are converted to silicon oxides, leaving abrasive deposits on engine components. These deposits cause increased maintenance costs and in some cases complete engine overhauls become necessary. ^ The objectives of this study were to compare the VMS types and levels present in biogas generated in the anaerobic digesters and landfills and evaluate the energetics of siloxane transformations under anaerobic conditions. Siloxane emissions, resulting from disposal of silicone-based materials, are expected to increase by 29% within the next 10 years. Estimated concentrations and the risk factors of exposure to siloxanes were evaluated based on the initial concentrations, partitioning characteristics and persistence. It was determined that D4 has the highest risk factor associated to bioaccumulation in liquid and solid phase, whereas D5 was highest in gas phase. Additionally, as siloxanes are combusted, the particle size range causes them to be potentially hazardous to human health. When inhaled, they may affix onto the alveoli of the lungs and may lead to development of silicosis. Siloxane-based COD-loading was evaluated and determined to be an insignificant factor concerning COD limits in wastewater. ^ Removal of siloxane compounds is recommended prior to land application of biosolids or combustion of biogas. A comparison of estimated costs was made between maintenance practices for removal of siloxane deposits and installation/operation of fixed-bed carbon absorption systems. In the majority of cases, the installation of fixed-bed adsorption systems would not be a feasible option for the sole purpose of siloxane removal. However they may be utilized to remove additional compounds simultaneously.^

Risk of African swine fever introduction into the European Union through transport-associated routes: returning trucks and waste from international ships and planes

BACKGROUND The uncontrolled presence of African swine fever (ASF) in Russian Federation (RF) poses a serious risk to the whole European Union (EU) pig industry. Although trade of pigs and their products is banned since the official notification in June 2007, the potential introduction of ASF virus (ASFV) may occur by other routes, which are very frequent in ASF, and more difficult to control, such as contaminated waste or infected vehicles. This study was intended to estimate the risk of ASFV introduction into the EU through three types of transport routes: returning trucks, waste from international ships and waste from international planes, which will be referred here as transport-associated routes (TAR). Since no detailed and official information was available for these routes, a semi-quantitative model based on the weighted combination of risk factors was developed to estimate the risk of ASFV introduction by TAR. Relative weights for combination of different risk factors as well as validation of the model results were obtained by an expert opinion elicitation. RESULTS Model results indicate that the relative risk for ASFV introduction through TAR in most of the EU countries (16) is low, although some countries, specifically Poland and Lithuania, concentrate high levels of risk, the returning trucks route being the analyzed TAR that currently poses the highest risk for ASFV introduction into the EU. The spatial distribution of the risk of ASFV introduction varies importantly between the analyzed introduction routes. Results also highlight the need to increase the awareness and precautions for ASF prevention, particularly ensuring truck disinfection, to minimize the potential risk of entrance into the EU. CONCLUSIONS This study presents the first assessment of ASF introduction into the EU through TAR. The innovative model developed here could be used in data scarce situations for estimating the relative risk associated to each EU country. This simple methodology provides a rapid and easy to interpret results on risk that may be used for a target and cost-effective allocation of resources to prevent disease introduction.

Improvement of termite resistance, dimensional stability and mechanical properties of pine wood by paraffin impregnation

Paraffin has been used as surface protection of wood throughout the ages but its use for impregnation to improve wood resistance to biodegradation is recent. This study determined the main improvements on wood properties with paraffin impregnation. Healthy Pinus pinaster Ait. wood was impregnated with paraffin at different levels using a hot–cold process. Weight gain, equilibrium moisture content and dimensional stability (ASE) at 35 and 65 % relative humidity, termite durability against Reticulitermes grassei (Clément), bending strength, bending stiffness (MOE) and Janka hardness were determined. Density increased from 0.57 to 0.99, ASE ranged between 38–96 % and 16–71 % for 35 and 65 % relative humidity, respectively. Equilibrium moisture content decreased from 9.9 and 12.0 % to 0.8 and 3.6 % for 35 and 65 % relative humidity. Termite durability improved from level 4 to level 3 of attack, and higher termite mortality was found in treated wood (52 % against 17 %). Bending strength (MOR) increased with paraffin weight gain, reaching a 39 % increase. MOE also increased by about 13 % for wood with a weight gain around 80 %. Janka hardness increased significantly reaching about 40 % for wood with 80 % weight gain. Paraffin impregnated wood has improved properties with regard to equilibrium moisture content, dimensional stability and density, bending strength and Janka hardness, and resistance against termites.

Investigating the Roles and Requirements, Manifestations and Management of Metadata in the Creation of Reliable and Preservation of Authentic Electronic Entities Created by Dynamic, Interactive and Experiential Systems: Report on the Work and Findings of the Interpares 2 Description Cross Domain Group

Metadata that is associated with either an information system or an information object for purposes of description, administration, legal requirements, technical functionality, use and usage, and preservation, plays a critical role in ensuring the creation, management, preservation and use and re-use of trustworthymaterials, including records. Recordkeeping1 metadata, of which one key type is archival description, plays a particularly important role in documenting the reliability and authenticity of records and recordkeeping systemsas well as the various contexts (legal-administrative, provenancial, procedural, documentary, and technical) within which records are created and kept as they move across space and time. In the digital environment, metadata is also the means by which it is possible to identify how record components – those constituent aspects of a digital record that may be managed, stored and used separately by the creator or the preserver – can be reassembled to generate an authentic copy of a record or reformulated per a user’s request as a customized output package.Issues relating to the creation, capture, management and preservation of adequate metadata are, therefore, integral to any research study addressing the reliability and authenticity of digital entities, regardless of the community, sector or institution within which they are being created. The InterPARES 2 Description Cross-Domain Group (DCD) examined the conceptualization, definitions, roles, and current functionality of metadata and archival description in terms of requirements generated by InterPARES 12. Because of the needs to communicate the work of InterPARES in a meaningful way across not only other disciplines, but also different archival traditions; to interface with, evaluate and inform existing standards, practices and other research projects; and to ensure interoperability across the three focus areas of InterPARES2, the Description Cross-Domain also addressed its research goals with reference to wider thinking about and developments in recordkeeping and metadata. InterPARES2 addressed not only records, however, but a range of digital information objects (referred to as “entities” by InterPARES 2, but not to be confused with the term “entities” as used in metadata and database applications) that are the products and by-products of government, scientific and artistic activities that are carried out using dynamic, interactive or experiential digital systems. The nature of these entities was determined through a diplomatic analysis undertaken as part of extensive case studies of digital systems that were conducted by the InterPARES 2 Focus Groups. This diplomatic analysis established whether the entities identified during the case studies were records, non-records that nevertheless raised important concerns relating to reliability and authenticity, or “potential records.” To be determined to be records, the entities had to meet the criteria outlined by archival theory – they had to have a fixed documentary format and stable content. It was not sufficient that they be considered to be or treated as records by the creator. “Potential records” is a new construct that indicates that a digital system has the potential to create records upon demand, but does not actually fix and set aside records in the normal course of business. The work of the Description Cross-Domain Group, therefore, addresses the metadata needs for all three categories of entities.Finally, since “metadata” as a term is used today so ubiquitously and in so many different ways by different communities, that it is in peril of losing any specificity, part of the work of the DCD sought to name and type categories of metadata. It also addressed incentives for creators to generate appropriate metadata, as well as issues associated with the retention, maintenance and eventual disposition of the metadata that aggregates around digital entities over time.

Assessing the role of Mediterranean evergreen oaks canopy cover in land surface albedo and temperature using a remote sensing-based approach

Modifications in vegetation cover can have an impact on the climate through changes in biogeochemical and biogeophysical processes. In this paper, the tree canopy cover percentage of a savannah-like ecosystem (montado/dehesa) was estimated at Landsat pixel level for 2011, and the role of different canopy cover percentages on land surface albedo (LSA) and land surface temperature (LST) were analysed. A modelling procedure using a SGB machine-learning algorithm and Landsat 5-TM spectral bands and derived vegetation indices as explanatory variables, showed that the estimation of montado canopy cover was obtained with good agreement (R2 = 78.4%). Overall, montado canopy cover estimations showed that low canopy cover class (MT_1) is the most representative with 50.63% of total montado area. MODIS LSA and LST products were used to investigate the magnitude of differences in mean annual LSA and LST values between contrasting montado canopy cover percentages. As a result, it was found a significant statistical relationship between montado canopy cover percentage and mean annual surface albedo (R2 = 0.866, p < 0.001) and surface temperature (R2 = 0.942, p < 0.001). The comparisons between the four contrasting montado canopy cover classes showed marked differences in LSA (χ2 = 192.17, df = 3, p < 0.001) and LST (χ2 = 318.18, df = 3, p < 0.001). The highest montado canopy cover percentage (MT_4) generally had lower albedo than lowest canopy cover class, presenting a difference of −11.2% in mean annual albedo values. It was also showed that MT_4 and MT_3 are the cooler canopy cover classes, and MT_2 and MT_1 the warmer, where MT_1 class had a difference of 3.42 °C compared with MT_4 class. Overall, this research highlighted the role that potential changes in montado canopy cover may play in local land surface albedo and temperature variations, as an increase in these two biogeophysical parameters may potentially bring about, in the long term, local/regional climatic changes moving towards greater aridity.

"Portuguese Observatory of Taeniasis and Cysticercosis": A "One Health" example for epidemiological surveillance of one neglected disease in a European country

Cysticercosis results from the ingestion Taenia solium eggs directly by faecal-oral route or contaminated food or water. Human tapeworm carriers who have become infected after ingesting pork meat contaminated with cysticerci release these eggs. Cysticercosis occurs after tapeworm eggs are ingested by an intermediate host (pig or human) and then hatch, migrate, and lodge in the host's tissues, where they develop onto larval cysticerci. When they lodged in the central nervous system of humans, results in the disease condition called Neurocysticercosis (NCC), with a heterogeneous manifestations depending of the locations of cysts, number, size and their stage of evolution (1). Consequently the prognostic ranges from asymptomatic to situations leading to death in 2% to 9.8%. of cases (7) In swine’s there are few studies, but recent works have proved that animals, for the same reasons, also have neurological abnormalities, expressed by seizures, stereotypic walk in circles, chewing motions with foamy salivation included tonic muscle contractions followed by a sudden diminution in all muscle tone leading to collapse (2). Conventional domestic wastewater treatment processes may not be totally effective in inactivating parasites eggs from Taenia solium, allowing some contamination of soils and agricultural products (11). In Portugal there are some evidence of aggregation of human cysticercosis cases in specific regions, bases in ecological design studies (6). There are few information about human tapeworm carriers and social and economic factors associated with them. Success in knowledge and consequently in lowering transmission is limited by the complex network of biological and social factors that maintain the spread. Effective control of mostly zoonosis require One Health approach, after a real knowledge and transparency in the information provided by the institutions responsible for both animal and human health, allowing sustained interventions targeted at the transmission cycle's crucial nodes. In general, the model used to control, reflects a rural reality, where pigs are raised freely, poor sanitation conditions and incipient sanitary inspection. In cysticercosis, pigs are obligate intermediate hosts and so considered as first targets for control and used as sentinels to monitor environmental T. solium contamination (3). Usually environmental contamination with Taenia spp. eggs is a key issue in most of studies with landscape factors influencing presence of Taenia spp. antigens in both pigs and humans (5). Soil-related factors as well as socio-economic and behavioural factors are associated with the emergence of significant clustering human cysticercosis (4,5). However scarce studies has been produced in urban environmental and in developed countries with the finality to characterize the spatial pattern. There are still few data available regarding its prevalence and spatial distribution; Transmission patterns are likely to exhibit correlations as housing conditions, water supply, basic sanitation, schooling and birthplace of the individual or relatives, more than pigs rearing free, soil conditions (9). As a matter of fact, tapeworm carriers from endemic zones can auto-infect or transmit infection to other people or arrive already suffering NCC (as a result of travelling to or being a citizen from an endemic cysticercosis country) to a free cysticercosis country. Transmission is fecal-oral; this includes transmission through person-to-person contact, through autoinfection, or through contaminated food This has been happening in different continents as North America (5.4–18% been autochthonous), Europe and Australia (7). Recently, case reports of NCC have also emerged from Muslim countries. (10). Actually, different papers relate an epidemic situation in Spain and Portugal (7, 8). However the kind of study done does not authorize such conclusion. There are no evidence that infections were acquired in Portugal and there are not characterized the mode of transmission. Papers with these kind of information will be allow to have economic consequences resulted from artificial trade barriers with serious consequences for pig producers and pig meat trade. We need transparency in information’s that allow provide the basis to support the development and targeting of future effective control programmes (and prove we need that). So, to have a real picture of the disease, it is necessary integrate data from human, animal and environmental factors surrounding human and pig cases to characterize the pattern of the transmission. The design needs to be able to capture unexpected, and not common outcomes (routine data). We need to think “One Health” to get a genuine image of the situation.

Climate seasonality limits leaf carbon assimilation and wood productivity in tropical forests.

The seasonal climate drivers of the carbon cy- cle in tropical forests remain poorly known, although these forests account for more carbon assimilation and storage than any other terrestrial ecosystem. Based on a unique combina- tion of seasonal pan-tropical data sets from 89 experimental sites (68 include aboveground wood productivity measure- ments and 35 litter productivity measurements), their asso- ciated canopy photosynthetic capacity (enhanced vegetation index, EVI) and climate, we ask how carbon assimilation and aboveground allocation are related to climate seasonal- ity in tropical forests and how they interact in the seasonal carbon cycle. We found that canopy photosynthetic capacity seasonality responds positively to precipitation when rain- fall is < 2000 mm yr-1 (water-limited forests) and to radia- tion otherwise (light-limited forests). On the other hand, in- dependent of climate limitations, wood productivity and lit- terfall are driven by seasonal variation in precipitation and evapotranspiration, respectively. Consequently, light-limited forests present an asynchronism between canopy photosyn- thetic capacity and wood productivity. First-order control by precipitation likely indicates a decrease in tropical forest pro- ductivity in a drier climate in water-limited forest, and in cur- rent light-limited forest with future rainfall < 2000 mm yr-1.

Modelling photochemical production of fine particulates in a toluene/NOx/water vapour system

This work investigates the computer modelling of the photochemical formation of smog products such as ozone and aerosol, in a system containing toluene, NOx and water vapour. In particular, the problem of modelling this process in the Commonwealth Scientific and Industrial Research Organization (CSIRO) smog chambers, which utilize outdoor exposure, is addressed. The primary requirement for such modelling is a knowledge of the photolytic rate coefficients. Photolytic rate coefficients of species other than N02 are often related to JNo2 (rate coefficient for the photolysis ofN02) by a simple factor, but for outdoor chambers, this method is prone to error as the diurnal profiles may not be similar in shape. Three methods for the calculation of diurnal JNo2 are investigated. The most suitable method for incorporation into a general model, is found to be one which determines the photolytic rate coefficients for N02, as well as several other species, from actinic flux, absorption cross section and quantum yields. A computer model was developed, based on this method, to calculate in-chamber photolysis rate coefficients for the CSIRO smog chambers, in which ex-chamber rate coefficients are adjusted by accounting for variation in light intensity by transmittance through the Teflon walls, albedo from the chamber floor and radiation attenuation due to clouds. The photochemical formation of secondary aerosol is investigated in a series of toluene-NOx experiments, which were performed in the CSIRO smog chambers. Three stages of aerosol formation, in plots of total particulate volume versus time, are identified: a delay period in which no significant mass of aerosol is formed, a regime of rapid aerosol formation (regime 1) and a second regime of slowed aerosol formation (regime 2). Two models are presented which were developed from the experimental data. One model is empirically based on observations of discrete stages of aerosol formation and readily allows aerosol growth profiles to be calculated. The second model is based on an adaptation of published toluene photooxidation mechanisms and provides some chemical information about the oxidation products. Both models compare favorably against the experimental data. The gross effects of precursor concentrations (toluene, NOx and H20) and ambient conditions (temperature, photolysis rate) on the formation of secondary aerosol are also investigated, primarily using the mechanism model. An increase in [NOx]o results in increased delay time, rate of aerosol formation in regime 1 and volume of aerosol formed in regime 1. This is due to increased formation of dinitrocresol and furanone products. An increase in toluene results in a decrease in the delay time and an increase in the rate of aerosol formation in regime 1, due to enhanced reactivity from the toluene products, such as the radicals from the photolysis of benzaldehyde. Water vapor has very little effect on the formation of aerosol volume, except that rates are slightly increased due to more OH radicals from reaction with 0(1D) from ozone photolysis. Increased temperature results in increased volume of aerosol formed in regime 1 (increased dinitrocresol formation), while increased photolysis rate results in increased rate of aerosol formation in regime 1. Both the rate and volume of aerosol formed in regime 2 are increased by increased temperature or photolysis rate. Both models indicate that the yield of secondary particulates from hydrocarbons (mass concentration aerosol formed/mass concentration hydrocarbon precursor) is proportional to the ratio [NOx]0/[hydrocarbon]0

Raised Floor System applications for refurbishing office spaces

While raised floors as a building component has been around since the 70's, its application in terms of a holistic system in the fit-out of commercial office buildings has not been fully embraced due to some inherent problems and negative perceptions of the stakeholders involved. Today, the new generation of raised floor systems(RFS) offers a suite of innovative and integrated products and solutions, and as such are not only suitable for the changing office space requirements, but also capable of meeting tbe smart and sustainable challenges, which are becoming the prerequisite in the refurbishment of existing buildings. As there has been a prediction for continued growth in refurbishment projects in major cities around the globe, RFS as an alternative methodology warrants new examination and highlight. This paper introduces research recently completed in Australia that provided a holistic approach to the application of RFS enabled by intelligent building technologies, and examined key issues of project development when refurbishing commercial office buildings. It focuses on the constructability of RFS, and how it will respond to smart feature requirements in buildings while extending service life, meeting new organisational change and workplace health needs for applications in today's office environment. It also introduces key project procurement issues and the integrated decision support when dealing with the refurbishment of office buildings. The paper recommends procurement strategies as well as the justification of adopting the RFS technology in the Australian office building sector. Given the current economic downturn, refitting as opposed to new build .projects will come onto the spotlight. This paper will provide valuable information for building owners and developers alike when contemplating the retrofit of office buildings.

An intelligent data mining technique for product quality improvement

Advances in data mining have provided techniques for automatically discovering underlying knowledge and extracting useful information from large volumes of data. Data mining offers tools for quick discovery of relationships, patterns and knowledge in large complex databases. Application of data mining to manufacturing is relatively limited mainly because of complexity of manufacturing data. Growing self organizing map (GSOM) algorithm has been proven to be an efficient algorithm to analyze unsupervised DNA data. However, it produced unsatisfactory clustering when used on some large manufacturing data. In this paper a data mining methodology has been proposed using a GSOM tool which was developed using a modified GSOM algorithm. The proposed method is used to generate clusters for good and faulty products from a manufacturing dataset. The clustering quality (CQ) measure proposed in the paper is used to evaluate the performance of the cluster maps. The paper also proposed an automatic identification of variables to find the most probable causative factor(s) that discriminate between good and faulty product by quickly examining the historical manufacturing data. The proposed method offers the manufacturers to smoothen the production flow and improve the quality of the products. Simulation results on small and large manufacturing data show the effectiveness of the proposed method.

Engaging energy saving through motivation-specific social comparison

Comparison is widely used in research projects and commercial products whose goal is to motivate energy saving at home. This research builds on fundamental theories from social psychology in an attempt to shed light on how to motivate consumers to conserve energy by providing relevant people for social comparison depending on consumer’s motivation to compare. To support the research process, the mobile application EnergyWiz was developed through a theory-driven design approach. Along with other features EnergyWiz provides users with three types of social comparison – normative, one-on-one and ranking. The results of interviews with prospective users are used to derive design suggestions for relevant people for comparison (comparison subjects).

Australian queer student activists' media representations of queer

Queer student activists are a visible aspect of Australian tertiary communities. Institutionally there are a number of organisations and tools representing and serving gay, lesbian, bisexual, transgender, intersex and ‘otherwise queer identifying’ (GLBTIQ) students. ‘Queer’ is a contentious term with meanings ranging from a complex deconstructive academic theory to a term for ‘gay’. Despite the institutional applications, the definition remains unclear and under debate. In this thesis I examine queer student activists’ production of print media, a previously under-researched area. In queer communities, print media provides crucial grounding for a model of queer. Central to identity formation and activism, this media is a site of textuality for the construction and circulation of discourses of queer student media. Thus, I investigate the various ways Australian queer student activists construct queer, queer identity, and queer activism in their print media. I use discourse analysis, participant observation and semi-structured interviews to enable a thorough investigation of both the process and the products of queer student media. My findings demonstrate that queer student activists’ politics are grounded in a range of ideologies drawing from Marxism, Feminism, Gay Liberation, Anti-assimilation and Queer Theory. Grounded in queer theoretical perspectives of performativity this research makes relatively new links between Queer Theory and Media Studies in its study of the production contexts of queer student media. In doing so, I show how the university context informs student articulations of queer, proving the necessity to locate research within its social-cultural setting. My research reveals that, much like Queer Theory, these representations of queer are rich with paradox. I argue that queer student activists are actually theorising queer. I call for a reconceptualisation of Queer Theory and question the current barriers between who is considered a ‘theorist’ of queer and who is an ‘activist’. If we can think about ‘theory’ as encompassing the work of activists, what implications might this have for politics and analysis?

Value-adding to cellulosic ethanol: Lignin polymers

Lignocellulosic waste materials are the most promising feedstock for generation of a renewable, carbon-neutral substitute for existing liquid fuels. The development of value-added products from lignin will greatly improve the economics of producing liquid fuels from biomass. This review gives an outline of lignin chemistry, describes the current processes of lignocellulosic biomass fractionation and the lignin products obtained through these processes, then outlines current and potential value-added applications of these products, in particular as components of polymer composites. Research highlights The use of lignocellulosic biomass to produce platform chemicals and industrial products enhances the sustainability of natural resources and improves environmental quality by reducing greenhouse and toxic emissions. In addition, the development of lignin based products improves the economics producing liquid transportation fuel from lignocellulosic feedstock. Value adding can be achieved by converting lignin to functionally equivalent products that rely in its intrinsic properties. This review outlines lignin chemistry and some potential high value products that can be made from lignin. Keywords: Lignocellulose materials; Lignin chemistry; Application