938 resultados para Microscopia - Força atômica
Resumo:
The use of biofuels remotes to the eighteenth century, when Rudolf Diesel made the first trials using peanut oil as fuel in a compression ignition engine. Based on these trials, there was the need for some chemical change to vegetable oil. Among these chemical transformations, we can mention the cracking and transesterification. This work aims at conducting a study using the thermocatalytic and thermal cracking of sunflower oil, using the Al-MCM-41 catalyst. The material type mesoporous Al-MCM-41 was synthesized and characterized by Hydrothermical methods of X-ray diffraction, scanning electron microscopy, nitrogen adsorption, absorption spectroscopy in the infrared and thermal gravimetric analysis (TG / DTG).The study was conducted on the thermogravimetric behavior of sunflower oil on the mesoporous catalyst cited. Activation energy, conversion, and oil degradation as a function of temperature were estimated based on the integral curves of thermogravimetric analysis and the kinetic method of Vyazovkin. The mesoporous material Al-MCM-41 showed one-dimensional hexagonal formation. The study of the kinetic behavior of sunflower oil with the catalyst showed a lower activation energy against the activation energy of pure sunflower oil. Two liquid fractions of sunflower oil were obtained, both in thermal and thermocatalytic pyrolisis. The first fraction obtained was called bio-oil and the second fraction obtained was called acid fraction. The acid fraction collected, in thermal and thermocatalytic pyrolisis, showed very high level of acidity, which is why it was called acid fraction. The first fraction was collected bio-called because it presented results in the range similar to petroleum diesel
Resumo:
The produced water is a byproduct formed due to production of petroleum and carries with it a high amount of contaminants such as oil particles in suspension, organic compounds and metals. Thus, these latter pollutants are very difficult to treat because of its high solubility in water. The objective of this work is to use and evaluate a microemulsioned system to remove metals ( K , Mg , Ba , Ca , Cr , Mn , Li , Fe ) of synthetic produced water. For the extraction of metals, it was used a pseudoternary diagram containing the following phases: synthetic produced water as the aqueous phase (AP), hexane as organic phase (OP), and a cosurfactant/surfactant ratio equal to four (C/S = 4) as the third phase, where the OCS (saponified coconut oil) was used as surfactant and n-butanol as cosurfactant. The synthetic produced water was prepared in a bench scale and the region of interest in the diagram for the removal of metals was determined by experimental design called. Ten points located in the phase Winsor II were selected in an area with a large amount of water and small amounts of reagents. The samples were analyzed in atomic absorption spectrometer, and the results were evaluated through a statistical assesment, allowing the efficiency analysis of the effects and their interactions. The results showed percentages of extraction above 90% for the metals manganese, iron, chromium, calcium, barium and magnesium, and around 45% for metals lithium and potassium. The optimal point for the simultaneous removal of metals was calculated using statistical artifact multiple response function (MR). This calculation showed that the point of greatest extraction of metals occurs was the J point, with the composition [72% AP, 9% OP, 19% C/S], obtaining a global extraction percentage about 80%. Considering the aspects analyzed, the microemulsioned system has shown itself to be an effective alternative in the extraction of metals on synthetic produced water remediation
Resumo:
Although there are a wide variety of additives that act in fresh state, to adjust the properties of cement, there is also a search by additions that improve the tenacity of the cement in the hardened state. This, in turn, can often be increased by inserting fibers, which act on the deflection of microcracks. This study aimed to use a microfiber glass wool (silica-based) as an additive reinforcing the cement matrix, improving the rupture tenacity, in order to prevent the propagation of microcracks in the cement sheath commonly found in oil wells submitted to high temperatures. The fibers were added at different concentrations, 2 to 5% (BWOC) and varied average sizes, grinding for 90 s, 180 s, 300 s, 600 s. The cement slurries were made with a density of 1,90 g/ cm3 (15,6 lb/gal), using Portland cement CPP- Special Class as the hydraulic binder and 40% silica flour. The characterization of the fiber was made by scanning electron microscopy (SEM), particle size by sieving, X-ray fluorescence (XRF), X-ray diffraction (XRD) and thermogravimetry (TG / DTG). Were performed technological tests set by the API (American Petroleum Institute) by rheology, stability, free water, compressive strength, as well as testing rupture energy, elastic modulus and permeability. The characterization results showed good thermal stability of the microfiber glass wool for application in oil wells submitted to steam injection and, also, that from the particle size data, it was possible to suggest that microfibers milled up to 300 s, are ideal to act as reinforcement to the cement slurries. The rheological parameters, there was committal of plastic viscosity when larger lengths were inserted of microfiber (F90). The values obtained by free water and stability were presented according to API. The mechanical properties, the incorporation of microfiber to the cement slurries gave better rupture tenacity, as compared to reference cement slurries. The values of compressive strength, elastic modulus and permeability have been maintained with respect to the reference cement slurries. Thus, cement slurries reinforced with microfiber glass wool can ensure good application for cementing oil wells submitted to steam injection, which requires control of microcracks, due to the thermal gradients
Resumo:
In this study, it has been investigated the influence of silver film deposition onto 100% polyester woven and non-woven, on the survival of Escherichia coli and Staphylococcus aureus in contact with these surfaces. The treatment was performedin a chamber containing the working gas at low pressure (~ 10-2 mbar). Some process parameters such as as voltage: 470 V; pressure: 10-2 mbar; current : 0.40 A and gas flow: 6 and 10 cm3/min were kept constant. For the treatments with purêargon plasma using a flow of 6 and 10 cm3/min, different treatment times were evaluated, such as, 10 , 20, 30, 40, 50 and 60 minutes. Contact angle (sessile drop), measurements were used to determine the surface tension of the treated fabrics and its influence on the bacteria grow as weel as the possibilities of a biofilm formation. The formation of a silver film, as well as the amount of this element was verified byEDX technique. The topography was observed through scanning electron microscopy (SEM) to determine the size of silver grains formed on the surfaces of the fabric and assess homogeneity of treatment. The X-ray diffraction (XRD) was used to analyze the structure of silver film deposition. The woven fabric treatments enabled the formation of silver particulate films with particle size larger than the non-woven fabrics. With respect to bacterial growth, all fabrics were shown to be bactericidal for Staphylococcus aureus (S. aureus), while for the Escherichia coli (E. coli), the best results were found for the non-woven fabric (TNT) treated with a flow of 10 cm3/min to both bacteria
Resumo:
Aiming to reduce and reuse waste oil from oily sludge generated in large volumes by the oil industry, types of nanostructured materials Al-MCM-41 and Al-SBA-15, with ratios of Si / Al = 50, were synthesized , and calcined solids used as catalysts in the degradation of oily sludge thermocatalytic oil from oilfield Canto do Amaro, in the state of Rio Grande do Norte. Samples of nanostructured materials were characterized by thermogravimetric analysis (TG / DTG), X-ray diffraction (XRD), scanning electron microscopy (SEM), absorption spectroscopy in the infrared Fourier transform (FT-IR) and adsorption nitrogen (BET). The characterization showed that the synthesized materials resulted in a catalyst nanostructure, and ordered pore diameter and surface area according to existing literature. The oily sludge sample was characterized by determining the API gravity and sulfur content and SARA analysis (saturates, aromatics, resins and asphaltenes). The results showed a material equivalent to the average oil with API gravity of 26.1, a low sulfur content and considerable amount of resins and asphaltenes, presented above in the literature. The thermal and catalytic degradation of the oily sludge oil was performed from room temperature to 870 ° C in the ratios of heating of 5, 10 and 20 ° C min-1. The curves generated by TG / DTG showed a more accelerated degradation of oily sludge when it introduced the nanostructured materials. These results were confirmed by activation energy calculated by the method of Flynn-Wall, in the presence of catalysts reduced energy, in particular in the range of cracking, showing the process efficiency, mainly for extraction of lightweight materials of composition of oily sludge, such as diesel and gasoline
Resumo:
The resistance of aluminum and their alloys, to the corrosion phenomenon, in aqueous solutions, is a result of the oxide layer formed. However, the corrosion process in the aluminum alloy is associated with the presence a second phase of particles or the presence of chloride ions which promote the disruption of the oxide layer located producing the corrosion process. On the other hand, the term water produced is used to describe the water after the separation of the oil and gas in API separators. The volumes of produced water arrive around 5 more times to the volume of oil produced. The greatest feature of the water is the presence of numerous pollutants. Due to the increased volume of waste around the world in the current decade, the outcome and the effect of the discharge of produced water on the environment has recently become an important issue of environmental concern where numerous treatments are aimed at reducing these contaminants before disposal. Then, this study aims to investigate the electrochemical corrosion behavior of aluminum alloy 6060 in presence of water produced and the influence of organic components as well as chloride ions, by using the electrochemical techniques of linear polarization. The modification of the passive layer and the likely breakpoints were observed by atomic force microscopy (AFM). In the pit formation potential around -0.4 to -0.8 V/EAg/AgCl was observed that the diffusion of chloride ions occurs via the layer formed with the probable formation of pits. Whereas, at temperatures above 65 °C, it was observed that the range of potential for thepit formation was -0.4 to -0.5 V/EAg/AgCl. In all reactions, the concentration of Al(OH)3 in the form of a gel was observed
Resumo:
Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)
Resumo:
Seaweeds are organisms known to exhibit a variety of biomolecules with pharmacological properties. The coast of Rio Grande do Norte has over 100 species of seaweeds, most of them not yet explored for their pharmacological potential. Sugars and phenolic compounds are the most studied of these being assigned a range of biological properties, such as anticoagulant , antiinflammatory, antitumor and antioxidant activities. In this work, we obtained methanolic extracts from thirteen seaweeds of the coast of Rio Grande do Norte (Dictyota cervicornis; Dictiopterys delicatula; Dictyota menstruallis; D. mertensis; Sargassum filipendula; Spatoglossum schröederi; Acanthophora specifera; Botryocladia occidentalis; Caulerpa cupresoides; C. racemosa; C. prolifera; C. sertularioides e Codium isthmocladum). They were evaluated as anticoagulant and antioxidant drugs, as well as antiproliferative drugs against the tumor cell line HeLa. None of the methanolic extracts showed anticoagulant activity, but when they were evaluated as antioxidant drugs all of extracts showed antioxidant activity in all tests performed (total antioxidant capacity, sequestration of superoxide and hydroxyl radicals, ferric chelation and reductase activity), especially the algae D. mentrualis, D. cilliolata and C. prolifera, who had the greatest potential to donate electrons.In addition, the ability of iron ions chelation appears as the main antioxidant mechanism of the methanolic extracts of these seaweeds mainly for the extract of the C. racemosa seaweed, which reached almost 100% activity. In the MTT assay, all extracts showed inhibitory activity at different levels againts HeLa cells. Moreover, D. cilliolata (MEDC) and D. menstrualis (MEDM) extracts showed specific activity to this cell line, not inhibiting the viability of 3T3 normal cell line, so they were chosen for detailing the antiproliferative mechanism of action. Using flow cytometry, fluorescence microscopy and in vitro assays we demonstrated that MEDC and MEDM induced apoptosis in HeLa cells by activation of caspases 3 and 9 and yet, MEDC induces cell cycle arrest in S phase. Together, these results showed that the methanolic extracts of brown seaweed D. menstrualis and D. cilliolata may contain agents with potential use in combatting cells from human uterine adenocarcinoma. This study also points to the need for more in-depth research on phytochemical and biological context to enable the purification of biologically active products of these extracts
Resumo:
Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)
Resumo:
Tamoxifen (TX), a drug used in the treatment of breast cancer, may cause hepatic changes in some patients. The consequences of its use on the liver tissues of rats with or without diabetes mellitus (DM) have not been fully explored. The purpose of this multidisciplinary study was to evaluate the correlation between plasma hepatic enzyme levels and the presence of iron overload in the hepatic tissue of female Wistar rats with or without streptozotocin-induced DM and using TX. Female rats were studied in control groups: C-0 (non-drug users), C-V (sorbitol vehicle only) and C-TX (using TX). DM (diabetic non-drug users) and DM-TX (diabetics using TX) were the test groups. Sixty days after induced DM, blood samples were collected for glucose, alanine aminotransferase (ALT), aspartate aminotransferase (AST) alkaline phosphatase (ALP) and bilirubin measures. Hepatic fragments were processed and stained with hematoxylin and eosin (H&E), Masson s trichrome, Perls. The hepatic iron content was quantified by atomic absorption spectrometry. AST, ALT and ALP levels were significantly elevated in the DM and DM-TX groups, with unchanged bilirubin levels. Liver iron overload using Perls stain and atomic absorption spectrometry were observed exclusively in groups C-TX and DM-TX. There was positive correlation between AST, ALT and ALP levels and microscopic hepatic siderosis intensity in group DM-TX. In conclusion, TX administration is associated with liver siderosis in diabetic and non-diabetic rats. In addition, TX induced liver iron overload with unaltered hepatic function in 2 non-diabetic rats and may be a useful tool for investigating the biological control of iron metabolism
Resumo:
The aim of the present study was to assess the effectiveness and adverse effects on dental enamel caused by nightguard vital bleaching with 10% carbamide peroxide. This was accomplished through the interaction of researchers from different areas such as dentistry, materials engineering and physics. Fifty volunteers took part in the doubleblind randomized controlled clinical trial. They were allocated to an experimental group that used Opalescence PF 10% (OPA) and a control group that used a placebo gel (PLA). Fragments of human dental enamel from the vestibular surface of healthy premolars, extracted for orthodontic reasons, were fixed to the vestibular surface of the first upper molars of the volunteers for in situ observation. Bleaching was performed at night for 21 days. The observation periods included Baseline (BL), T0 (21 days), T30 (30 days after treatment) and T180 (180 days after treatment, only for the OPA group). Tooth color was assessed by comparing it with the Vita® scale and by the degree of satisfaction expressed by the volunteer. We also assessed adverse clinical effects, dental sensitivity and gingival bleeding. The study of adverse effects on enamel was conducted in vivo and in situ, using the DIAGNOdent® laser fluorescence device to detect mineral loss. Scanning electron microscopy (SEM) was used to check for superficial morphological alterations, energy dispersive spectrophotometry (EDS) to semiquantitatively assess chemical composition using the Ca/P ratio, and the x-ray diffraction (XRD) technique to observe alterations in enamel microstructure. The results showed that nightguard vital bleaching with 10% carbamide peroxide was effective in 96% of the cases, versus 8% for the PLA group. Dental sensitivity was present in 36% (9/25) of the cases. There was no significant association between gingival bleeding and the type of gel used (p = 1.00). In vivo laser fluorescence analysis showed no difference in values for the control group, whereas in the OPA group there was a statistically significant difference between baseline values in relation to the subsequent periods (p<0.01), with lower mean values for post-bleaching times. There was a significant difference between the groups for times T0 and T30. Micrographic analysis showed no enamel surface alterations related to the treatment performed. No significant alteration in Ca/P ratio was observed in the OPA group (p = 0.624) or in the PLA group (p = 0.462) for each of the observation periods, nor between the groups studied (p=0.102). The XRD pattern for both groups showed the presence of three-phase Hydroxyapatite according to JCPDS files (9-0432[Ca5(PO4)3(OH)], 18-0303[Ca3(PO4)2.xH2O] and 25-0166[Ca5(PO4)3(OH, Cl, F)]). No other peak associated to other phases was found, independent of the group analyzed, which reveals there was no disappearance, nucleation or phase transformation. Neither was there any alteration in peak pattern location. With the methodology and protocol used in this study, nightguard vital bleaching with 10% carbamide peroxide proved to be an effective and safe procedure for dental enamel
Resumo:
Conselho Nacional de Desenvolvimento Científico e Tecnológico
Resumo:
The aim of this study was to assess the acute and chronic effects of zinc in serum iron profile of children aged 6-9 years in relation to nutritional status and dietary intake. The study participants were 11 children regardless of sex, aged 6-9 years. They were selected from three public schools of the city of Natal, Brazil. Body mass index was used to assess nutritional status. In order to determine the patterns of childhood growth and ideal weight we used the standards of the World Health Organization. The dietary intake assessment was based on information from a three-day prospective food survey. The variables were energy intake, protein, lipids, carbohydrates, fiber, calcium, iron and zinc. All children underwent an intravenous administration of zinc (IVAZn) before and after oral administration of zinc (OAZn) (5 mg Zn / day) for three months. We measured serum iron, hematocrit, hemoglobin and total protein, before and after the use of oral zinc. The analysis of hematocrit, hemoglobin and total protein was performed using standard methods of clinical laboratory. Zinc levels and serum iron were measured by atomic absorption spectrophotometry. The project was evaluated and approved by the Ethics in Research Committee of Federal University of Rio Grande do Norte. Results: All children had normal weight. The consumption of energy, fat, fiber, calcium and iron were below recommended levels. However, the levels of protein and carbohydrates were high. Protein and zinc increased significantly after OAZn. Carbohydrate and protein were elevated in the blood. After OAZn, both protein and zinc increased, being statistically significant. Conclusion: The potential inhibitory effect of physiological or pharmacological doses of zinc on the profile of serum iron was observed in children with healthy weight and aged between 6 and 9 years. This negative effect of zinc did not affect the levels of hematocrit or hemoglobin, and therefore did not cause anemia. This was a multidisciplinary study, involving researchers from medicine, nutrition and pharmacy. This met the requirements of multidisciplinarity of the Post Graduate Program in Health Sciences of Federal University of Rio Grande do Norte.
Resumo:
Although many studies point to alterations in the organic concentrations of zinc in elderly patients, the mechanisms by which aging might cause changes in the metabolism of this nutrient remain unclear. Thus, we assessed the changes in plasma zinc, Zinc Binding Capacity to Plasma Protein (ZnBCPP) and Saturation Index (SI), comparing elderly individuals and young adults. The zinc analyses were performed by atomic absorption spectrophotometry. A statistically significant difference (p < 0.001) was found between the two groups, in relation to plasma zinc and SI, but the ZnBCPP did not differ between the younger and older subjects. In agreement with this result, it was shown in the young group that 76% (R2 = 0.760) of the ZnBCPP variations are explained by the variations in plasma zinc and SI. In the elderly group this measure decreased to 30.5% (R2 = 0.305). We conclude, therefore, that aging may be a factor associated to changes in control mechanisms and in zinc homeostasis, and could even alter ZnBCPP response patterns and other zinc-related indicators of nutritional status.
Resumo:
A resistência microbiana a antimicrobianos tem favorecido a busca por substâncias bioativas provenientes de plantas usadas na medicina popular, com o intuito de se obter novos fármacos com atividade antimicrobiana. Neste estudo, foi proposta a investigação da atividade antibacteriana do óleo-resina de Copaifera duckei e de diferentes extratos da casca de Pseudobombax marginatum, e seus possíveis mecanismos de ação. O potencial inibitório antibacteriano foi avaliado utilizando-se os métodos de difusão e diluição em ágar, e a bioautografia. O mecanismo de ação foi analisado por microscopia eletrônica, no qual se observou alterações na ultraestrutura bacteriana, e por eletroforese em SDS-PAGE, que determinou ação sobre as proteínas das superfícies celulares. A análise química foi realizada pelas técnicas de Espectrometria de massas acoplada ao Cromatógrafo a gás- EM/CG (C. duckei) e Cromatografia Líquida de Alta Eficiência- CLAE (P. marginatum). Entre as bactérias estudadas, B. cereus foi a mais suscetível às plantas em estudo, com concentrações inibitórias mínimas (CIMs) correspondentes a 0,3125 mg/mL para o óleo-resina de copaíba, e 0,5 mg/mL para extrato hidroalcoólico (1:1) e 0,512 mg/mL para a fração butanólica da casca P. marginatum, nos quais pôde-se observar alterações na parede celular do B. cereus, com remoção da camada S, espessamento da parede celular e formação de diversos septos nos centros de divisão celular. A análise química por EM/CG mostrou compostos terpênicos no óleo-resina de C. duckei, tendo como composto majoritário o β-bisaboleno, e a análise por CLAE mostrou a presença de compostos derivados da catequina na casca do P. marginatum. Desta forma, as plantas em estudo mostram um potencial antibacteriano considerável, podendo contribuir tanto na terapia antimicrobiana como na área de alimentos, tendo como um de seus prováveis sítios de ação a parede celular bacteriana