Applications of accurate, high-precision Pb isotope ratio measurement by multi-collector ICP-MS

The isotope composition of Ph is difficult to determine accurately due to the lack of a stable normalisation ratio. Double and triple-spike addition techniques provide one solution and presently yield the most accurate measurements. A number of recent studies have claimed that improved accuracy and precision could also be achieved by multi-collector ICP-MS (MC-ICP-MS) Pb-isotope analysis using the addition of Tl of known isotope composition to Pb samples. In this paper, we verify whether the known isotope composition of Tl can be used for correction of mass discrimination of Pb with an extensive dataset for the NIST standard SRM 981, comparison of MC-ICP-MS with TIMS data, and comparison with three isochrons from different geological environments. When all our NIST SRM 981 data are normalised with one constant Tl-205/Tl-203 of 2.38869, the following averages and reproducibilities were obtained: Pb-207/Pb-206=0.91461+/-18; Pb-208/Ph-206 = 2.1674+/-7; and (PbPh)-Pb-206-Ph-204 = 16.941+/-6. These two sigma standard deviations of the mean correspond to 149, 330, and 374 ppm, respectively. Accuracies relative to triple-spike values are 149, 157, and 52 ppm, respectively, and thus well within uncertainties. The largest component of the uncertainties stems from the Ph data alone and is not caused by differential mass discrimination behaviour of Ph and Tl. In routine operation, variation of sample introduction memory and production of isobaric molecular interferences in the spectrometer's collision cell currently appear to be the ultimate limitation to better reproducibility. Comparative study of five different datasets from actual samples (bullets, international rock standards, carbonates, metamorphic minerals, and sulphide minerals) demonstrates that in most cases geological scatter of the sample exceeds the achieved analytical reproducibility. We observe good agreement between TIMS and MC-ICP-MS data for international rock standards but find that such comparison does not constitute the ultimate. test for the validity of the MC-ICP-MS technique. Two attempted isochrons resulted in geological scatter (in one case small) in excess of analytical reproducibility. However, in one case (leached Great Dyke sulphides) we obtained a true isochron (MSWD = 0.63) age of 2578.3 +/- 0.9 Ma, which is identical to and more precise than a recently published U-Pb zircon age (2579 3 Ma) for a Great Dyke websterite [Earth Planet. Sci. Lett. 180 (2000) 1-12]. Reproducibility of this age by means of an isochron we regard as a robust test of accuracy over a wide dynamic range. We show that reliable and accurate Pb-isotope data can be obtained by careful operation of second-generation MC-ICP magnetic sector mass spectrometers. (C) 2002 Elsevier Science B.V. All rights reserved.

Application of the maximum entropy method to the (2 + 1)D four-fermion model

We investigate spectral functions extracted using the maximum entropy method from correlators measured in lattice simulations of the (2+1)-dimensional four-fermion model. This model is particularly interesting because it has both a chirally broken phase with a rich spectrum of mesonic bound states and a symmetric phase where there are only resonances. In the broken phase we study the elementary fermion, pion, sigma, and massive pseudoscalar meson; our results confirm the Goldstone nature of the π and permit an estimate of the meson binding energy. We have, however, seen no signal of σ→ππ decay as the chiral limit is approached. In the symmetric phase we observe a resonance of nonzero width in qualitative agreement with analytic expectations; in addition the ultraviolet behavior of the spectral functions is consistent with the large nonperturbative anomalous dimension for fermion composite operators expected in this model.

One-dimensional quantum walk with unitary noise

The effect of unitary noise on the discrete one-dimensional quantum walk is studied using computer simulations. For the noiseless quantum walk, starting at the origin (n=0) at time t=0, the position distribution P-t(n) at time t is very different from the Gaussian distribution obtained for the classical random walk. Furthermore, its standard deviation, sigma(t) scales as sigma(t)similar tot, unlike the classical random walk for which sigma(t)similar toroott. It is shown that when the quantum walk is exposed to unitary noise, it exhibits a crossover from quantum behavior for short times to classical-like behavior for long times. The crossover time is found to be Tsimilar toalpha(-2), where alpha is the standard deviation of the noise.

The medicine and epidemiology of bovine respiratory disease in feedlots

Bovine Respiratory Disease (BRD) results from a complex, multifactorial interaction of stressors, animal susceptibility, and respiratory pathogens. The infectious agents associated with BRD are ubiquitous among cattle populations. Typically, one or a combination of stressors are necessary to initiate BRD. Prevention of BRD should, therefore, address management procedures to minimise stressors. Administration of vaccines against BRD agents may help reduce the incidence of BRD but is unlikely to eliminate the condition. The effectiveness of antimicrobials in the treatment of BIRD depends primarily on early recognition and treatment. The use of antioxidant vitamins, minerals or other agents in the prevention and treatment of BRD warrants further research.

In overweight patients with chronic hepatitis C, circulating insulin is associated with hepatic fibrosis: implications for therapy

Background/Aims: Host factors such as increased body mass index (BMI) and genotype-specific viral factors contribute to the development of steatosis in patients with chronic hepatitis C (HCV). We hypothesized that host metabolic factors associated with increased BMI may play a role in disease progression. Methods: Fasting serum was collected from 160 patients with chronic HCV at the time of liver biopsy and 45 age, gender and BMI matched controls, and assessed for levels of insulin, c-peptide and leptin. Results: Patients with viral genotype 3 had more severe steatosis (P = 0.0001) and developed stages 1 and 2 fibrosis at a younger age (P < 0.05) than patients with genotype 1. For both genotypes, overweight patients had significantly more steatosis and increased insulin and leptin levels. In contrast to lean patients, there was a statistically significant increase in circulating insulin levels with increasing fibrosis in overweight patients with chronic HCV (P = 0.03). Following multivariate analysis, insulin was independently associated with fibrosis (P = 0.046) but not inflammation (P = 0.83). There was no association between serum leptin levels and stage of fibrosis. Conclusions: Increasing circulating insulin levels may be a factor responsible for the association between BMI and fibrosis in patients with HCV, irrespective of viral genotype. (C) 2003 European Association for the Study of the Liver. Published by Elsevier B.V. All rights reserved.

Assessing forest fire as a potential PCDD/F source in Queensland, Australia

Forest fires are suggested as a potential and significant source of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs), even though no studies to date provide sufficient evidence to confirm forest fires as a source of PCDD/Fs. Recent investigations in Gueensland, Australia have identified a widespread contamination of PCDDs (in particular OND) in soils and sediments in the coastal region from an unknown source of PCDD/Fs. Queensland is predominately rural; it has few known anthropogenic sources of PCDD/Fs, whereas forest fires are a frequent occurrence. This study was conducted to assess forest fires as a potential source of the unknown PCDD/F contamination in Queensland. A combustion experiment was designed to assess the overall mass of PCDD/Fs before and after a simulated forest fire. The results from this study did not identify an increase in Sigma-PCDD/Fs or OCDD after the combustion process. However, specific non-2,3,7,8 substituted lower chlorinated PCDD/Fs were elevated after the combustion process, suggesting formation from a precursor. The results from this study indicate that forest fires are unlikely to be the source of the unknown PCDD contamination in Gueensland, rather they are a key mechanism for the redistribution of PCDD/Fs from existing sources and precursors.

An SNP-based PCR assay to differentiate between Listeria monocytogenes lineages derived from phylogenetic analysis of the sigB gene

The alternative sigma factor sigB gene is involved in the stress response regulation of Listeria monocytogenes, and contributes towards growth and survival in adverse conditions. This gene was examined to determine if it could be a useful indicator of lineage differentiation, similar to the established method based on ribotyping. The sigB sequence was resolved in four local L. monocytogenes strains and the phylogenetic relationship among these, and a further 21 sigB gene sequences from strains of different serotype and lineage including two Listeria innocua strains, obtained from the GenBank database were determined. The sigB nucleotide sequences of these 25 Listeria strains were then examined for single nucleotide polymorphic (SNP) sites that could differentiate between the three lineages. Based on nucleotide sequences L. monocytogenes lineage F serotype 1/2b and 4b clustered together, lineage II/serotype 1/2a and 1/2c strains clustered together, lineage III/serotypes 4a and 4c strains clustered together and L. innocua strains clustered together as an outgroup. SNPs differentiating the three lineages were identified. Individual allele-specific PCR reactions based on these polymorphisms were successful in grouping known and a further 37 local L. monocytogenes isolates into the three lineages. (C) 2003 Elsevier B.V. All fights reserved.

Análise da fibrose do tecido adiposo de mulheres submetidas à abdominoplastia e cirurgia bariátrica

A fibrose é um acúmulo demasiado de matriz extracelular, resultante de um desequilíbrio entre a síntese e a degradação dos seus componentes. É associada às alterações metabólicas do tecido adiposo, contudo sua ocorrência nos diferentes depósitos e repercussões clínicas ainda não são totalmente compreendidas. O objetivo deste estudo foi analisar a fibrose no tecido adiposo em relação à presença de obesidade, localização do depósito [tecido adiposo subcutâneo abdominal (TASA) e visceral (TAV)] e sua associação a variáveis clínicas. Amostras de gordura do TASA e TAV foram obtidas de 21 mulheres submetidas à cirurgia bariátrica (IMC>40Kg/m2) e 25 amostras de TASA das submetidas à abdominoplastia (IMC<30Kg/m2). As amostras foram processadas para histologia convencional. O corante picrosirius foi utilizado para avaliação das fibras colágenas totais. As imagens obtidas foram analisadas no ADIPOSOFT®. O percentual de fibrose no TASA e no TAV foi analisado com testes estatísticos não paramétricos, adotando-se um valor de p<0,05. A fibrose no TASA foi maior em mulheres com obesidade (p<0.0006). A fibrose entre os depósitos de TASA e de TAV foi observada apenas em mulheres pardas e negras com obesidade (p<0,012). A fibrose no TASA não foi correlacionada com as variáveis clínicas nas mulheres sem obesidade. No entanto, nas submetidas à cirurgia bariátrica, foram observadas correlações da fibrose no TASA com Índice de Massa Corpórea (IMC), hemoglobina glicada (A1c), LDL e triglicerídeos; e no TAV com porcentagem de perda gordura pré-operatório, % de perda de gordura total, % de massa magra pré, Taxa Metabólica Basal (TBM) e Gasto Energético Basal (GEB). Os parâmetros metabólicos e de perfil antropométrico antes da cirurgia bariátrica foram associados à fibrose no TASA, enquanto os parâmetros após a cirurgia foram associados à fibrose no TAV.

Reducing fuel consumption through modular vehicle architectures

By identifying energy waste streams in vehicles fuel consumption and introducing the concept of lean driving systems, a technological gap for reducing fuel consumption was identified. This paper proposes a solution to overcome this gap, through a modular vehicle architecture aligned with driving patterns. It does not address detailed technological solutions; instead it models the potential effects in fuel consumption through a modular concept of a vehicle and quantifies their dependence on vehicle design parameters (manifesting as the vehicle mass) and user behavior parameters (driving patterns manifesting as the use of a modular car in lighter and heavier mode, in urban and highway cycles). Modularity has been functionally applied in automotive industry as manufacture and assembly management strategies; here it is thought as a product development strategy for flexibility in use, driven by environmental concerns and enabled by social behaviors. The authors argue this concept is a step forward in combining technological solutions and social behavior, of which eco-driving is a vivid example, and potentially evolutionary to a lean, more sustainable, driving culture.

A Wireless EEG Acquisition Platform based on Embedded Systems

This paper proposes a wireless EEG acquisition platform based on Open Multimedia Architecture Platform (OMAP) embedded system. A high-impedance active dry electrode was tested for improving the scalp- electrode interface. It was used the sigma-delta ADS1298 analog-to-digital converter, and developed a “kernelspace” character driver to manage the communications between the converter unit and the OMAP’s ARM core. The acquired EEG signal data is processed by a “userspace” application, which accesses the driver’s memory, saves the data to a SD-card and transmits them through a wireless TCP/IP-socket to a PC. The electrodes were tested through the alpha wave replacement phenomenon. The experimental results presented the expected alpha rhythm (8-13 Hz) reactiveness to the eyes opening task. The driver spends about 725 μs to acquire and store the data samples. The application takes about 244 μs to get the data from the driver and 1.4 ms to save it in the SD-card. A WiFi throughput of 12.8Mbps was measured which results in a transmission time of 5 ms for 512 kb of data. The embedded system consumes about 200 mAh when wireless off and 400 mAh when it is on. The system exhibits a reliable performance to record EEG signals and transmit them wirelessly. Besides the microcontroller-based architectures, the proposed platform demonstrates that powerful ARM processors running embedded operating systems can be programmed with real-time constrains at the kernel level in order to control hardware, while maintaining their parallel processing abilities in high level software applications.

Application of Gage R&R methodology for improving the training and evaluation of automatic optical inspection machine operators

The current level of demand by customers in the electronics industry requires the production of parts with an extremely high level of reliability and quality to ensure complete confidence on the end customer. Automatic Optical Inspection (AOI) machines have an important role in the monitoring and detection of errors during the manufacturing process for printed circuit boards. These machines present images of products with probable assembly mistakes to an operator and him decide whether the product has a real defect or if in turn this was an automated false detection. Operator training is an important aspect for obtaining a lower rate of evaluation failure by the operator and consequently a lower rate of actual defects that slip through to the following processes. The Gage R&R methodology for attributes is part of a Six Sigma strategy to examine the repeatability and reproducibility of an evaluation system, thus giving important feedback on the suitability of each operator in classifying defects. This methodology was already applied in several industry sectors and services at different processes, with excellent results in the evaluation of subjective parameters. An application for training operators of AOI machines was developed, in order to be able to check their fitness and improve future evaluation performance. This application will provide a better understanding of the specific training needs for each operator, and also to accompany the evolution of the training program for new components which in turn present additional new difficulties for the operator evaluation. The use of this application will contribute to reduce the number of defects misclassified by the operators that are passed on to the following steps in the productive process. This defect reduction will also contribute to the continuous improvement of the operator evaluation performance, which is seen as a quality management goal.

Sistema para formação e avaliação dos operadores das máquinas de inspeção ótica automática

A montagem de circuitos eletrónicos é um processo extremamente complexo, e como tal muito difícil de controlar. Ao longo do processo produtivo, é colocada solda no PCB (printed circuit board), seguidamente são colocados os componentes eletrónicos que serão depois soldados através de um sistema de convecção, sendo por fim inspecionados todos os componentes, com o intuito de detetar eventuais falhas no circuito. Esta inspeção é efetuada por uma máquina designada por AOI (automatic optical inspection), que através da captura de várias imagens do PCB, analisa cada uma, utilizando algoritmos de processamento de imagem como forma de verificar a presença, colocação e soldadura de todos os componentes. Um dos grandes problemas na classificação dos defeitos relaciona-se com a quantidade de defeitos mal classificados que passam para os processos seguintes, por análise errada por parte dos operadores. Assim, apenas com uma formação adequada, realizada continuamente, é possível garantir uma menor taxa de falhas por parte dos operadores e consequentemente um aumento na qualidade dos produtos. Através da implementação da metodologia Gage R&R para atributos, que é parte integrante da estratégia “six sigma” foi possível analisar a aptidão dos operadores, com base na repetição aleatória de várias imagens. Foi desenvolvido um software que implementa esta metodologia na formação dos operadores das máquinas AOI, de forma a verificar a sua aptidão, tendo como objetivo a melhoria do seu desempenho futuro, através da medição e quantificação das dificuldades de cada pessoa. Com esta nova sistemática foi mais fácil entender a necessidade de formação de cada operador, pois com a constante evolução dos componentes eletrónicos e com o surgimento de novos componentes, estão implícitas novas dificuldades para os operadores neste tipo de tarefa. Foi também possível reduzir o número de defeitos mal classificados de forma significativa, através da aposta na formação com o auxílio do software desenvolvido.

Integration of management systems: towards a sustained success and development of organizations

Effective environmental management within companies, integrated with other management areas like quality and occupational health and safety, is nowadays assumed to be a strategic way to implement and improve lean and cleaner production. Also, sustainable development (SD) and business sustainability can be achieved through a better coordinated management of processes versus associated resources. This paper presents an in depth discussion regarding the promotion of integrated management systems, their benefits and major contribution towards the sustainable development of cleaner production related features. It addresses issues regarding the contributions resulting from the integration of standardized Management System (MS) from both internal and external perspectives. Complementing the overall review of aspects to the development of integrated management systems a survey was conducted in order to better understand the relevance of the identified success factors. The main findings in this paper are as follows: a contextualization model of sustainable development and integrated management systems considering the Triple Bottom Line: economic, social and environmental; and, a method and associated model to support the development of integrated management systems as well as general guidelines to support integration. It can be concluded that a proactive approach and commitment to cleaner production, supported by an integrated management system, brings relevant savings for organizations as well as providing value to the relevant interested parties.

Body composition, muscle strength, functional capacity, and physical disability risk in liver transplanted familial amyloidotic polyneuropathy patients

Abstract: Background: Familial amyloidotic polyneuropathy (FAP) is a neurodegenerative disease leading to sensory and motor polyneuropathies, and functional limitations. Liver transplantation is the only treatment for FAP, requiring medication that negatively affects bone and muscle metabolism. The aim of this study was to compare body composition, levels of specific strength, level of physical disability risk, and functional capacity of transplanted FAP patients (FAPTx) with a group of healthy individuals (CON). Methods: A group of patients with 48 FAPTx (28 men, 20 women) was compared with 24 CON individuals (14 men, 10 women). Body composition was assessed by dual-energy X-ray absorptiometry, and total skeletal muscle mass (TBSMM) and skeletal muscle index (SMI) were calculated. Handgrip strength was measured for both hands as was isometric strength of quadriceps. Muscle quality (MQ) was ascertained by the ratio of strength to muscle mass. Functional capacity was assessed by the six-minute walk test. Results: Patients with FAPTx had significantly lower functional capacity, weight, body mass index, total fat mass, TBSMM, SMI, lean mass, muscle strength, MQ, and bone mineral density. Conclusion: Patients with FAPTx appear to be at particularly high risk of functional disability, suggesting an important role for an early and appropriately designed rehabilitation program.